Search NASA⌕ Search

SEARCH · Search NASA

Results for “Conducted Emissions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Comparative life cycle analysis on ethylene production from electrocatalytic reduction of carbon dioxide

Ethylene is one of the largest greenhouse gas emitters and the most diversly used commodity chemicals globally. Electrocatalytic reduction of CO 2 to ethylene received great attention from the research society to decarbonize the ethylene production. Here, in this study, a life-cycle analysis is conducted using the Greenhouse Gases, Regulated Emissions, and Energy use in Technologies (GREET) model on the three electrocatalytic CO 2 -reduction pathways (or “e-ethylene” pathways): i) cascade conversion via carbon monoxide intermediate; ii) single-step conversion in membrane electrode assembly (MEA); and iii) single-step conversion in alkaline flow cell. The results showed that the electricity consumption is the lowest for the cascade pathway (164 MJ/kg), thus resulting in the lowest cradle-to-gate carbon intensity [18 kgCO 2 e/kg with United States (US) average grid)] among the three pathways followed by the single-step MEA (32 kgCO 2 e/kg) and then by the single-step alkaline (56 kgCO 2 e/kg). However, all three e-ethylene pathways were significantly more carbon-intensive than their fossil-based counterpart (1.1 kgCO 2 e/kg) due to their excessive energy consumption with the current state of technology. With renewable electricity, all three pathways yielded negative carbon intensity: from -3.1 kgCO 2 e/kg to -1.6 kgCO 2 e/kg depending on the source of CO 2 . The threshold carbon intensity of electricity (TCIE), defined as the upper bound of the carbon intensity of electricity to achieve lower carbon intensity for e-ethylene compared to fossil-based ethylene, is calculated for both current and future state of e-ethylene technologies. The cascade pathway had the highest TCIE out of the three e-ethylene pathways for both current (92 gCO 2 e/kWh) and future (124 gCO 2 e/kWh) state of technologies. However, the carbon intensity of average US grid (i.e., 467 and 303 gCO 2 e/kWh for current and future projections) were higher than the TCIEs of the corresponding timeline. Thus, reducing electricity requirement for e-ethylene pathways and bringing low-carbon generation mix in the United States (US) grid faster than the current projection are both essential to decarbonize ethylene and its downstream chemicals/polymers.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Synthetic and Mechanistic Implications of Chlorine Photoelimination in Nickel/Photoredox C(sp 3 )–H Cross-Coupling

In recent years, the development of light-driven reactions has contributed numerous advances in synthetic organic chemistry. A particularly active research area combines photoredox catalysis with nickel catalysis to accomplish otherwise inaccessible cross-coupling reactions. In these reactions, the photoredox catalyst absorbs light to generate an electronically excited charge-transfer state that can engage in electron or energy transfer with a substrate and the nickel catalyst. Our group questioned whether photoinduced activation of the nickel catalyst itself could also contribute new approaches to cross-coupling. Over the past 5 years, we have sought to advance this hypothesis for the development of a suite of mild and site-selective C(sp 3 )–H cross-coupling reactions with chloride-containing coupling partners via photoelimination of a Ni–Cl bond. On the basis of a report from the Nocera laboratory, we reasoned that photolysis of a Ni(III) aryl chloride species, generated by single-electron oxidation of a typical Ni(II) intermediate in cross-coupling, might allow for the catalytic generation of chlorine atoms. Combining this with the ability of Ni(II) to accept alkyl radicals, we hypothesized that photocatalytically generated chlorine atoms could mediate hydrogen atom transfer (HAT) with C(sp 3 )–H bonds to generate a substrate-derived alkyl radical that is captured by the Ni center in cross-coupling. A photoredox catalyst was envisioned to promote the necessary single-electron oxidation and reduction of the Ni catalyst to facilitate an overall redox-neutral process. Overall, this strategy would offer a visible-light-driven mechanism for chlorine radical formation enabled by the sequential capture of two photons. As an initial demonstration, we developed a Ni/photoredox-catalyzed α-oxy C(sp 3 )–H arylation of cyclic and acyclic ethers. This method was extended to a mild formylation of abundant and complex aryl chlorides through selective 2-functionalization of 1,3-dioxolane. Seeking to develop a suite of reactions that introduce carbon at all different oxidation states, we explored C(sp 3 )–H cross-coupling with trimethyl orthoformate, a common laboratory solvent. We found that trimethyl orthoformate serves as a source of methyl radical for a methylation reaction via β-scission from a tertiary radical generated upon chlorine-mediated HAT. Since chlorine radical is capable of abstracting unactivated C(sp 3 )–H bonds, our efforts have also been directed at cross-coupling with a range of feedstock chemicals, such as alkanes and toluenes, along with late-stage intermediates, using chloroformates as coupling partners. Overall, this platform enables access to valuable synthetic transformations with (hetero)aryl chlorides, which despite being the most ubiquitous and inexpensive aryl halide coupling partners, are rarely reactive in Ni/photoredox catalysis. Little is known about the photophysics and photochemistry of organometallic Ni complexes relevant to cross-coupling. We have conducted mechanistic investigations, including computational, spectroscopic, emission quenching, and stoichiometric oxidation studies, of Ni(II) aryl halide complexes common to Ni/photoredox reactions. These studies indicate that chlorine radical generation from excited Ni(III) is operative in the described C(sp 3 )–H functionalization methods. More generally, the studies illustrate that the photochemistry of cross-coupling catalysts cannot be ignored in metallaphotoredox reactions. We anticipate that further mechanistic understanding should facilitate catalyst design and lead to the development of new synthetic methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Renewable Polyurethanes from Sustainable Biological Precursors

Due to the depletion of fossil fuels, higher oil prices, and greenhouse gas emissions, the scientific community has been conducting an ongoing search for viable renewable alternatives to petroleum-based products, with the anticipation of increased adaptation in the coming years. New academic and industrial developments have encouraged the utilization of renewable resources for the development of ecofriendly and sustainable materials, and here, we focus on those advances that impact polyurethane (PU) materials. Vegetable oils, algae oils, and polysaccharides are included among the major renewable resources that have supported the development of sustainable PU precursors to date. Renewable feedstocks such as algae have the benefit of requiring only sunshine, carbon dioxide, and trace minerals to generate a sustainable biomass source, offering an improved carbon footprint to lessen environmental impacts. Incorporation of renewable content into commercially viable polymer materials, particularly PUs, has increasing and realistic potential. Biobased polyols can currently be purchased, and the potential to expand into new monomers offers exciting possibilities for new product development. This Review highlights the latest developments in PU chemistry from renewable raw materials, as well as the various biological precursors being employed in the synthesis of thermoset and thermoplastic PUs. We also provide an overview of literature reports that focus on biobased polyols and isocyanates, the two major precursors to PUs.

09 BIOMASS FUELS↗
DOE OSTI2023

Accelerating Quantum Materials Development with Advances in Transmission Electron Microscopy

Quantum materials are driving a technology revolution in sensing, communication, and computing, while simultaneously testing many core theories of the past century. Materials such as topological insulators, complex oxides, superconductors, quantum dots, color center-hosting semiconductors, and other types of strongly correlated materials can exhibit exotic properties such as edge conductivity, multiferroicity, magnetoresistance, superconductivity, single photon emission, and optical-spin locking. These emergent properties arise and depend strongly on the material’s detailed atomic-scale structure, including atomic defects, dopants, and lattice stacking. In this review, we describe how progress in the field of electron microscopy (EM), including in situ and in operando EM, can accelerate advances in quantum materials and quantum excitations. We begin by describing fundamental EM principles and operation modes. We then discuss various EM methods such as (i) EM spectroscopies, including electron energy loss spectroscopy (EELS), cathodoluminescence (CL), and electron energy gain spectroscopy (EEGS); (ii) four-dimensional scanning transmission electron microscopy (4D-STEM); (iii) dynamic and ultrafast EM (UEM); (iv) complementary ultrafast spectroscopies (UED, XFEL); and (v) atomic electron tomography (AET). We describe how these methods could inform structure–function relations in quantum materials down to the picometer scale and femtosecond time resolution, and how they enable precision positioning of atomic defects and high-resolution manipulation of quantum materials. For each method, we also describe existing limitations to solve open quantum mechanical questions, and how they might be addressed to accelerate progress. Among numerous notable results, our review highlights how EM is enabling identification of the 3D structure of quantum defects; measuring reversible and metastable dynamics of quantum excitations; mapping exciton states and single photon emission; measuring nanoscale thermal transport and coupled excitation dynamics; and measuring the internal electric field and charge density distribution of quantum heterointerfaces- all at the quantum materials’ intrinsic atomic and near atomic-length scale. Finally, we conclude by describing open challenges for the future, including achieving stable sample holders for ultralow temperature (below 10K) atomic-scale spatial resolution, stable spectrometers that enable meV energy resolution, and high-resolution, dynamic mapping of magnetic and spin fields. With atomic manipulation and ultrafast characterization enabled by EM, quantum materials will be poised to integrate into many of the sustainable and energy-efficient technologies needed for the 21st century.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

High-current electron sources for Superconducting Radiofrequency injectors

Accelerators are finding increasing use in numerous fields such as medicine, industry accelerator-based nuclear energy programs and others. A recent survey reveals only 20 high-energy accelerators worldwide serve elementary-particle physics while thousands of accelerators are routinely used in hospitals and industry (packaging, food sterilization, etc.).

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Evaluation of Thermal & Mechanical Properties of Additively Manufactured Monolithic SiC for Solar Receiver Applications

Increasing the operating temperatures of solar receivers is paramount to the efficiency of concentrated solar thermal (CST) and solar power (CSP) systems. Owing to its high temperature stability combined with excellent thermal and optical properties, SiC has been the material of choice for application in high-temperature solar receivers. State-of-the-art SiC volumetric concentrating solar air receivers such as the honeycomb design have successfully demonstrated in field exit air temperatures approaching 800oC. However, a successful application of CST systems for the decarbonization of heat reliant industrial sectors requires significant increases in the temperature capability of SiC receiver technology. Supported by an award from the Solar Technology Office (SETO), US Department of Energy (DOE), GE Research in collaboration with Heliogen Holdings Inc, is engaged in the development of an ultra-High Operating Temperature SiC-matrix Solar Thermal Air Receiver (HOTSSTAR) enabled by additive manufacturing. The program objective is to design and demonstrate a techno-economically viable SiC air receiver technology that can achieve exit air temperatures up to 1100oC for CST applications. We report and discuss the results of our testing and evaluation of thermal and mechanical properties of reaction-bonded SiC fabricated via binder jet printing to support the receiver component design, development, and analyses.

14 SOLAR ENERGY↗
DOE OSTI2025

Gas-Gap Calorimeter Sizing and Rating Tools for Heat Pipe Experimentation

Effective gas-gap calorimeter sizing and rating tools are required to design calorimeters that enable well-defined operating conditions, high cooling powers, and accurate calorimetry. The present report describes two tools utilizing Microsoft Excel and MathWorks MATLAB that enable the sizing and rating of gas-gap calorimeters with a He-Ar binary gas mixture in the gap. The Excel tools are two easy-to-use spreadsheets for calculating heat pipe operating temperature or He-Ar mole fractions given the required inputs. The MATLAB tool includes similar models with more robust solution algorithms along with sub-options for full-vacuum, static gas-gap, and forced circulation in the gas-gap. The accuracy of the developed tools were demonstrated by comparing with existing work in literature. The MATLAB tool was used for a parametric study to determine the gas-gap thickness, coolant gap thickness, coolant flow rate, and coolant inlet temperatures for the testing of a 3/4 in outer diameter heat pipe up to powers of 10 kW and temperatures of 1,000°C. The effects of heat pipe and calorimeter inner shell surface emissivities were investigated, considering the inability to control or accurately measure surface emissivities in most applications. It was found that controlling the He-Ar mole fractions provides a wide operating range for gas-gap thicknesses around ~ 0.042--0.090 in (~ 1.07--2.29 mm) for a surface emissivity range of 0.4--0.8, since conduction heat transfer is a significant fraction of the heat transfer across the gas-gap. In addition, it was found that turbulent flow in the coolant gap is needed at high input powers to prevent shell temperatures from approaching the boiling temperature of the water coolant. The parametric study resulted in choosing stainless steel tubes with an outer diameter and thickness of 1 x 0.065 in as the inner shell, and a 1-1/2 x 0.156 in as the outer shell of the calorimeter. Overall, this report presents the necessary information for the sizing and rating of gas-gap calorimeters with He-Ar mixtures for the testing of high-temperature heat pipes (~ 500--1,000°C).

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Mobile measurement of CH4 around the SGP ARM site during June 23-26, 2024

A mobile measurement campaign from June 23-26, 2024 was conducted to detect and quantify CH₄ emissions within about 8 km of the SGP site. Using a LI-COR LI-7810 tracer gas analyzer mounted on a vehicle, we sampled CH₄ along predefined routes surrounding a suspected source area around the SGP ARM site. Measurements were collected between 04:30 and 09:00 local time when the PBL was shallow, increasing sensitivity to surface emissions. Driving speeds were kept below 5 mph to minimize pressure-related artifacts.

{"Trace Gas Analyzer for methane","Measured mixing↗
DOE OSTI2022

Hybrid Capture for Net-Negative Emissions

The Energy & Environmental Research Center, in partnership with the U.S. Department of Energy and North Dakota ethanol producer Red Trail Energy, LLC (RTE), completed an initial engineering design (IED) for a potential hybrid capture system at the RTE CCS (carbon capture and storage) site. The RTE CCS Project is currently operating a CO2 capture facility, adjacent to the RTE ethanol facility in western North Dakota, and injecting the CO2 more than a mile below RTE property for permanent storage. This novel process would add capturing CO2 produced from natural gas boilers to the existing bioprocessing capture system to achieve a net-negative CO2 emissions industrial process at commercial scale (~310,000 tonnes/yr CO2). Initial findings of the IED showed the hybrid system to be technically viable with a moderate estimated cost of $55/tonne CO2 captured for the hybrid system. A cradle-to-gate life cycle assessment (LCA) was also conducted, showing preliminary net-negative carbon emissions potential anticipated from implementing a hybrid CCS system at a commercial scale. Recommended next steps toward potential implementation include hybrid capture system demonstration testing for detailed engineering and LCA model comparisons with low-carbon fuel incentive programs for financial support.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

US energy system transitions under cumulative emissions budgets

Cumulative emissions budgets are increasingly being used by decision makers and analysts to understand emissions reductions and associated transitions in the context of long-term goals such as limiting global mean temperature increase over the century to 1.5 or 2°C (IPCC, 2014). While previous studies have explored the implications of cumulative emissions budgets for the global economy, few studies have conducted regional and national-level analyses (Iyer et al., 2015; Riahi et al., 2015). This paper explores cumulative emissions budgets through 2050 consistent with the 1.5 and 2°C long-term temperature goals in the context of the United States. We employ a state-level model of the United States embedded within a global human-Earth system model (GCAM-USA) to study the implications of such budgets for the U.S. energy system (Iyer et al., 2017a; Iyer et al., 2017b). Our results show that achieving the stringent cumulative emissions budgets entails accelerated deployment of energy conserving technology, almost complete decarbonization of the power sector and increased electrification of buildings and industrial end-use sectors and decarbonization of transport employing a combination of electrification and the substitution of bioenergy for fossil fuels by the mid-century. We also find substantial state-level differences in the relative roles of these decarbonization strategies. Furthermore, our results highlight that increased ambition in the near-term will be valuable in setting the stage for smoother transformations in the future to achieve stringent cumulative emissions budgets consistent with long-term temperature goals established by the international community.

Feijoo, Felipe↗
DOE OSTI2024

SHOCK TUBE IGNITION STUDIES OF RENEWABLE DIESEL FUELS FOR MEDIUM AND HEAVY-DUTY TRANSPORTATION

Currently extensive research on alternative fuels is being conducted due to their increasing demand to reduce greenhouse emissions. One renewable fuel studied in this work is dimethyl ether (DME) blended with propane(C3H8) as a potential mixture for heavy-duty engines used in semi-trucks. The blend has the potential to drastically reduce particulate and greenhouse gas emissions compared to a conventional diesel engine operating under similar conditions. To develop the use of mixture, one must conduct detailed conceptual and simulation studies before progressing to detail studies in CFD, engine modifications, and live testing. For simulations, accurate high-fidelity chemical kinetic models are necessary. However, the validity of the chemical kinetic mechanism for operating conditions of a heavy-duty mixing-controlled compression (MCCI) engine was widely unknown until recent work presented here and published. In this work, we studied the ignition of DME and propane blends in a shock tube under MCCI engine conditions. Ignition delay time (IDT) gathered behind the reflected shock for DME-propane mixtures for heavy-duty compression ignition (CI) engine parameters. Testing was conducted for undiluted varieties spanning from temperatures of 700 to 1100 K at pressures ranging from 55 to 84 bar for various blends (100% CH3OCH3, 100% C3H8, 60% CH3OCH3/ 40% C3H8) of DME and propane were combusted in synthetic air (21% O2/ 79% N2). Several experiments were conducted at higher pressures (90-120 bar) to improve the model performance and accuracy. The ignition delay times (IDTs) were compared to recent mechanisms, including Aramco3.0, NUIG, and Dames et al. A common trend among the mechanisms was overpredicted experimental IDTs. Further studies were conducted by a sensitivity analysis using the Dames et al. model, and critical reactions sensitive to IDTs of DME-propane mixture near 60 bar are outlined. Chemical analysis was conducted on the NTC region to explain chemical kinetics which is critical for developing MCCI heavy duty engines.

Mohammed, Zuhayr Pasha↗
DOE OSTI2025

Effect of self-generated magnetic fields on x-ray emission in Kr-filled targets at the National Ignition Facility

We examine the effects of self-generated magnetic fields in a Kr gas pipe x-ray source platform. X-ray emission from Kr plasma is dependent on the plasma conditions, as the ionization state is largely a function of temperature. Magnetic fields are known to limit heat conduction, which increases temperature. We show that the emission in simulations of the gas pipe x-ray source is dependent on how self-generated magnetic fields are modeled. The inclusion of self-generated magnetic fields in simulations more accurately captures the emission of lower energy x-ray emission (L-shell), bringing results closer to experiments. The modeled x-ray emission and self-generated magnetic fields are shown to be particularly sensitive to the inclusion of the Nernst effect in simulations. Severely limiting the Nernst effect leads to a hotter Kr plasma, which can account for the discrepancy seen in earlier studies. By modifying the Nernst effect multiplier, we can achieve better experimental agreement in x-ray emission from gas pipes; the value of the multiplier that leads to the best agreement is dependent on the laser power of the drive. Currently, the suppression factor of the Nernst effect needed for high power drives (PL>200 TW) is more restrictive than what is currently put forward by non-local models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Techno-Economic Analysis and Life Cycle Assessment of Waste Lignin Fractionation and Valorization Using the ALPHA Process

Techno-Economic Analysis (TEA) and Life Cycle Assessment (LCA) were performed on the Aqueous Lignin Purification with Hot Agents (ALPHA) process, which is being investigated for the fractionation and purification of raw, bulk lignins recovered from cellulosic ethanol biorefineries or Kraft pulp mills. Here, ALPHA is proposed for the isolation of lignin from a corn stover-to-ethanol plant into purified low, medium, and high molecular weight (MW) fractions for producing polyurethane foam, activated carbon, and carbon fiber, respectively. A scenario analysis was conducted to determine the effect of ALPHA solvent choice on process economics and environmental performance. Solvent choice was found to have a significant impact on ALPHA, with a minimum selling price of 838/tonne with use of acetic acid vs 463/tonne with ethanol. Conversion of the lignin, processed with ethanol solvent, to high-value products yields 151 million/year in profit, which over 30 years results in a total net present value of 533 million. A life cycle assessment was conducted to determine the “gate-to-gate” greenhouse gas emissions and energy consumption of the lignin-based products compared to fossil-based equivalents. In conclusion, a value allocation scenario was conducted and it was determined that products generated using the ALPHA process with ethanol have similar or lower greenhouse gas emissions than the same products from fossil feedstocks.

09 BIOMASS FUELS↗
DOE OSTI2025

Combined TDLAS and chemiluminescence imaging in a flat flame burner operated with NH3/H2 blends

Ammonia is a promising hydrogen carrier due to its favorable storage and transport characteristics. However, its direct use in combustion systems is limited by low flammability and potential for high nitrogen oxide emissions. To better understand ammonia combustion, researchers conducted experiments using a flat flame burner and measured species profiles using tunable-diode-laser-absorption-spectroscopy and chemiluminescence imaging. They tested three flame conditions with different ammonia-hydrogen blends and oxygen levels. The results were compared to simulations using various kinetic mechanisms, including one that accounts for excited species chemistry. The goal is to provide direct information about species profiles in a simple system, isolating chemical kinetics from fluid dynamic effects, which can inform the development of more efficient and low-emission combustion systems using ammonia.

ammonia combustion↗
DOE OSTI2021

Molecular dynamics simulations of energy accommodation between gases and polymers for ultra-low thermal conductivity insulation

Determining the energy accommodation between gases and solids is essential to developing porous thermal insulation materials with ultra-low effective thermal conductivity that reduce energy use, greenhouse gas emissions, and fossil fuel consumption. The energy accommodation coefficients of most gases, however, have been rarely studied, especially with respect to solids that have relatively high thermal resistivity, e.g., polymers. Here, by using all-atom nonequilibrium molecular dynamics simulations, we reveal the accommodation coefficients of He, Ar, N 2 , and O 2 with polymers, mainly polystyrene. We find that their values are around 0.51, 0.72, 0.79, and 0.90, respectively, suggesting a critical reexamination of the commonly used theoretical maximum value of 1. We have also conducted experiments and validated the value for air, which is about 0.81. Such a change in accommodation coefficients can lead to a reduction of about 70%, 50%, 35%, and 20% in the thermal conductivity of He, Ar, N 2 , and O 2 gases in nano pores (below 100 nm) or at low pressures (below 1 millibar). With these new accommodation coefficients, we find that in a 10 nm pore with ambient pressure at 300 K, the gas thermal conductivity of He, Ar, N 2 , and O 2 in porous polystyrene can be as low as 9.7 × 10 –4 , 3.4 × 10 –4 , 7.3 × 10 –4 , and 8.5 × 10 –4 W·m –1 ·K –1 , respectively, which are two to three orders of magnitude lower than their bulk values, promising higher thermal resistivity of insulation materials. This work reveals the fundamental energy exchange between gases and polymers, providing important guidance for designing high-performance thermal insulation materials for various applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Role of Interface Band Alignment in Epitaxial SrTiO 3 /GaAs Heterojunctions

Recent concerns surrounding climate change and the contribution of fossil fuels to greenhouse gas (GHG) emissions have sparked interest and advancements in renewable energy sources including wind, solar, and hydroelectricity. These energy sources, often referred to as “clean energy”, generate no operational onsite GHG emissions. They also offer the potential for clean hydrogen production through water electrolysis, presenting a viable solution to create an environmentally friendly alternative energy carrier with the potential to decarbonize industrial processes reliant on hydrogen. To conduct a full life cycle analysis, it is crucial to account for the embodied emissions associated with renewable and nuclear power generation plants as they can significantly impact the GHG emissions linked to hydrogen production and its derived products. In this work, we conducted a comprehensive analysis of the embodied emissions associated with solar photovoltaic (PV), wind, hydro, and nuclear electricity. We investigated the implications of including plant-embodied emissions in the overall emission estimates of electrolysis hydrogen production and subsequently on the production of synthetic ammonia, methanol, and Fischer– Tropsch (FT) fuels. Results show that average embodied GHG emissions of solar PV, wind, hydro, and nuclear electricity generation in the United States (U.S.) were estimated to be 37, 9.8, 7.2, and 0.3 g CO 2 e/kWh, respectively. Life cycle GHG emissions of electrolytic hydrogen produced from solar PV, wind, and hydroelectricity were estimated as 2.1, 0.6, and 0.4 kg of CO 2 e/kg of H 2 , respectively, in contrast to the zero-emissions often used when the embodied emissions in their construction were excluded. Average life cycle emission estimates (CO 2 e/kg) of synthetic ammonia, methanol, and FT-fuel from solar PV electricity are increased by 5.5, 16, and 49 times, respectively, compared to the case when embodied emissions are excluded. This change also depends on the local irradiance for solar power, which can result in a further increase of GHG emissions by 35–41% in areas of low irradiance or reduce GHG emissions by 21–25% in areas with higher irradiance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Spectral emission properties of a nitrogen-doped diamond (001) photocathode: Hot electron transport and transverse momentum filtering

The electron emission properties of a single-crystal nitrogen-doped diamond(001) photocathode inserted in a 10 kV DC photoelectron gun are determined using a tunable (235–410 nm) ultraviolet laser radiation source for photoemission from both the back nitrogen-doped substrate face and the front homoepitaxially grown and undoped diamond crystal face. Here, the measured spectral trends of the mean transverse energy and quantum efficiency of the emitted electrons are both anomalous and nonmonotonic, but are shown to be consistent with (i) the known physics of electron photoexcitation from the nitrogen substitution states into the conduction bands of diamond, (ii) the energy position and dispersion characteristics of the conduction bands of diamond in the (001) emission direction, (iii) the effective electron affinity of the crystal faces, (iv) the strong electron-(optical)phonon coupling in diamond, and (v) the associated hot electron transport dynamics under energy equipartition with the optical phonons. Notably, the observed hot electron emission is shown to be restricted parallel to the photocathode surface by the low transverse effective masses of the emitting band states—a transverse momentum filtering effect.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strained bilayer WSe 2 with reduced exciton-phonon coupling

We explore excitonic absorption and emission in bilayer WSe 2 under tensile strain. We observe a redshift of 110 meV in the energy of the A exciton absorption peak (at the direct gap at the K point in the Brillouin zone) under 2.1% uniaxial tensile strain. In addition, under the same strain, the spectral linewidth of the A exciton at room temperature decreases by a factor of 2, from 70 to 36 meV. We show that this decrease is a result of suppression of phonon-mediated exciton scattering channels. This suppression is associated with the relative upshift under strain of the Q valley in the conduction band (involved in the indirect exciton emission), which is nearly degenerate with the K valley (involved in the A exciton). We analyze the strain-dependent absorption and photoluminescence spectra to determine the relative positions of these valleys and to infer intervalley scattering rates. Our model describes well the decrease and the distinct trends in the A exciton linewidth of monolayer and bilayer WSe 2 under strain. The findings show that strain can be used to tune, as well as to probe, the relative energies of band extrema and exciton scattering channels in two-dimensional semiconductors.

36 MATERIALS SCIENCE↗