Search NASA⌕ Search

SEARCH · Search NASA

Results for “Constraints”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

Multidisciplinary Design Optimization of Low-Boom Supersonic Aircraft with Mission Constraints

Conceptual design of low-boom supersonic aircraft is heavily dictated by aircraft volume and lift distributions. These unique design characteristics make it a challenge to enforce mission requirements (such as static margins and trim requirements) during design optimization. This low-boom design challenge is resolved by using reversed equivalent area targets for low-fidelity low-boom inverse design and a block coordinate optimization (BCO) method for multidisciplinary design optimization (MDO). The corresponding low-boom MDO problem includes aircraft mission constraints on ranges, cruise speeds, trim for low-boom cruise, static margins for takeoff/cruise/landing, takeoff/landing field lengths, approach velocity, and tail rotation angles for trim at takeoff/landing, as well as fuselage volume constraints for passengers and main gear storage. The BCO method is developed to optimally resolve the conflicts between the low-boom inverse design objective and other design constraints. This method is successfully applied to design a low-boom supersonic configuration that carries 40 passengers, flies a low-boom mission with cruise Mach of 1.6 and range of 2,500 nm, and cruises overwater at Mach 1.8 with range of 3,600 nm. The generated configuration satisfies all specified mission constraints and has the potential to match a reversed equivalent area target with ground noise level below 70 PLdB.

Multidisciplinary design optimization↗
NASA NTRS1972

Redundancy of constraints in the classical and quantum theories of gravitation.

It is shown that in Dirac's version of the quantum theory of gravitation, the Hamiltonian constraints are greatly redundant. If the Hamiltonian constraint condition is satisfied at one point on the underlying, closed three-dimensional manifold, then it is automatically satisfied at every point, provided only that the momentum constraints are everywhere satisfied. This permits one to replace the usual infinity of Hamiltonian constraints by a single condition which may be taken in the form of an integral over the manifold. Analogous theorems are given for the classical Einstein Hamilton-Jacobi equations.

Moncrief, V.↗
NASA NTRS1974

Time-fixed rendezvous by impulse factoring with an intermediate timing constraint

A method is presented for factoring a two-impulse orbital transfer into a three- or four-impulse transfer which solves the rendezvous problem and satisfies an intermediate timing constraint. Both the time of rendezvous and the intermediate time of a alinement are formulated as any element of a finite sequence of times. These times are integer multiples of a constant plus an additive constant. The rendezvous condition is an equality constraint, whereas the intermediate alinement is an inequality constraint. The two timing constraints are satisfied by factoring the impulses into collinear parts that vectorially sum to the original impulse and by varying the resultant period differences and the number of revolutions in each orbit. Five different types of solutions arise by considering factoring either or both of the two impulses into two or three parts with a limit for four total impulses. The impulse-factoring technique may be applied to any two-impulse transfer which has distinct orbital periods.

Green, R. N.↗
NASA NTRS1975

Effect of attitude constraints on solar-electric geocentric transfers

The present work assesses the increase in flight time and fuel consumption due to introducing attitude constraints on both the thrust vector and the plane of the solar cell arrays on geocentrically orbiting spacecraft. A modified version of the SECKSPOT computer program calculates nearly time-optimal trajectories for the constrained case of zero pitch and roll. Unconstrained cases are generated with the SECKSPOT code. It is concluded that with a pitch constraint but without a roll constraint, power would not be a function of thrust direction, and so the time-optimal thruster direction would be along the projection of the primer vector in the plane normal to the radius vector. The roll constraint would cause power to become a function of thrust angle and sun angle. For certain sun angles the locus of the ratio of power to maximum power is concave and thus there may be jumps in the control angle. Comparisons are made for a SERT-C type mission between constrained and unconstrained cases in an inverse square gravity field.

Sackett, L. L.↗
NASA NTRS1979

Combined strength and aeroelastic wing synthesis via constraint approximation

A numerical optimization program using constraint approximations for preliminary sizing of wing structural design parameters to satisfy simultaneous strength and aeroelastic requirements is described. The effects of wing flexibility on loads and flutter are included. The iterative procedure approximates wing internal load distributions and flutter response in generating design constraints. Though a linear Taylor series approximation to the variation of flutter speed is made, constraints in general are formulated as nonlinear and solved in a minimum weight problem using a feasible directions search. The technique is demonstrated for the determination of the optimal ply orientations and for simultaneous sizing for strength and flutter with simple constraint approximations.

Mullen, J., Jr.↗
NASA NTRS1981

Effect of ply constraint on fatigue damage development in composite material laminates

It is shown that the effects of constraint on the response of composite materials can be classified as (1) in-plane effects, and (2) through-the-thickness effects; with in-plane constraint being the principal contributor to notched strength and changes in notched strength under quasi-static loading. It is also determined that the constraint situations that produce the greatest static strength do not minimize the extent of damage that develops under either static or cyclic loading, and that through-the-thickness constraint controls the pattern and spacing of transverse cracks in the characteristic damage state that determines those of strength and stress in unnotched laminates. It is concluded that the mode and the extent of damage in notched and unnotched constrained plies is governed by the stress state in those plies, as determined by the constraining ones, and the relationship of stress and strength states.

Stinchcomb, W. W.↗
NASA NTRS1982

Optimality criteria design and stress constraint processing

Methods for pre-screening stress constraints into either primary or side-constraint categories are reviewed; a projection method, which is developed from prior cycle stress resultant history, is introduced as an additional screening parameter. Stress resultant projections are also employed to modify the traditional stress-ratio, side-constraint boundary. A special application of structural modification reanalysis is applied to the critical stress constraints to provide feasible designs that are preferable to those obtained by conventional scaling. Sample problem executions show relatively short run times and fewer design cycle iterations to achieve low structural weights; those attained are comparable to the minimum values developed elsewhere.

Levy, R.↗
NASA NTRS1982

Hybrid optimization of truss structures with strength and buckling constraints

An efficient scheme utilizing standard nonlinear programming methodology is presented for the optimal design of elastic, redundant structures with strength and buckling constraints. Numerical examples are given which demonstrate how this method, involving a constraint redefinition, can successfully overcome certain problems typical to such structures. The scheme is applied to the design of a cantilever truss with strength and buckling constraints, in which optimal nonuniform cross section columns are used for all elements critical in buckling. It is found that permitting node movement and adding redundancies can lower the weight of the structure for the prescribed design constraints. In addition, the node excursions in this configuration are shown to be relatively small.

Hajela, P.↗
NASA NTRS1983

Structural optimization with dynamic behavior constraints

The minimum weight optimum design of damped linearly elastic structural systems subjected to periodic loading with behavior constraints on maximum deflections and side constraints on design variables is addressed. Attention is focused on the two major impediments to an optimal solution: (1) the time parametric nature of the behavior constraints; and (2) the severe nonconvexity of the design space. A solution method based on upper bound approximations for the behavior constraints and an innovative mathematical programming scheme for seeking the optimal frequency subspace is set forth. Numerical results for several test problems illustrate the effectiveness of the method reported.

Mills-Curran, W. C.↗
NASA NTRS1983

Constraints on the invariant functions of axisymmetric turbulence

Constraints are derived for the two invariant functions Q1 and Q2 that occur in Chandrasekhar's (1950) development of the axisymmetric turbulence theory. These constraints must be satisfied for the correlation tensor derived from Q1 and Q2 to be that of a stationary random process, i.e., for the turbulence to be realizable. The equivalent results in spectrum space are also developed. Applications of the constraints in aerodynamic noise modeling are discussed. It is shown that significant errors in prediction can be introduced by the use of turbulence models which violate the constraints.

Kerschen, E. J.↗
NASA NTRS1985

Development and application of a unified balancing approach with multiple constraints

The development of a general analytic approach to constrained balancing that is consistent with past influence coefficient methods is described. The approach uses Lagrange multipliers to impose orbit and/or weight constraints; these constraints are combined with the least squares minimization process to provide a set of coupled equations that result in a single solution form for determining correction weights. Proper selection of constraints results in the capability to: (1) balance higher speeds without disturbing previously balanced modes, thru the use of modal trial weight sets; (2) balance off-critical speeds; and (3) balance decoupled modes by use of a single balance plane. If no constraints are imposed, this solution form reduces to the general weighted least squares influence coefficient method. A test facility used to examine the use of the general constrained balancing procedure and application of modal trial weight ratios is also described.

Zorzi, E. S.↗
NASA NTRS1986

Numerical difficulties associated with using equality constraints to achieve multi-level decomposition in structural optimization

There has been recent interest in multidisciplinary multilevel optimization applied to large engineering systems. The usual approach is to divide the system into a hierarchy of subsystems with ever increasing detail in the analysis focus. Equality constraints are usually placed on various design quantities at every successive level to ensure consistency between levels. In many previous applications these equality constraints were eliminated by reducing the number of design variables. In complex systems this may not be possible and these equality constraints may have to be retained in the optimization process. In this paper the impact of such a retention is examined for a simple portal frame problem. It is shown that the equality constraints introduce numerical difficulties, and that the numerical solution becomes very sensitive to optimization parameters for a wide range of optimization algorithms.

Thareja, R.↗
NASA NTRS1988

Minimum weight design of rotorcraft blades with multiple frequency and stress constraints

Minimum weight designs of helicopter rotor blades with constraints on multiple coupled flap-lag natural frequencies are studied. Constraints are imposed on the minimum value of the blade autorotational inertia to ensure sufficient rotary inertia to autorotate in case of engine failure and on stresses to guard against structural failure due to blade centrifugal forces. Design variables include blade taper ratio, dimensions of the box beam located inside the airfoil and magnitudes of nonstructural weights. The program CAMRAD is used for the blade modal analysis; the program CONMIN is used for the optimization. A linear approximation involving Taylor series expansion is used to reduce the analysis effort. The procedure contains a sensitivity analysis consisting of analytical derivatives for objective function and constraints on autorotational inertia and stresses. Central finite difference derivatives are used for frequency constraints. Optimal designs are obtained for both rectangular and tapered blades. Using this method, it is possible to design a rotor blade with reduced weight, when compared to a baseline blade, while satisfying all the imposed design requirements.

Chattopadhyay, Aditi↗
NASA NTRS1988

Knowledge based tools for Hubble Space Telescope planning and scheduling: Constraints and strategies

The Hubble Space Telescope (HST) presents an especially challenging scheduling problem since a year's observing program encompasses tens of thousands of exposures facing numerous coupled constraints. Recent progress in the development of planning and scheduling tools is discussed which augment the existing HST ground system. General methods for representing activities, constraints, and constraint satisfaction, and time segmentation were implemented in a scheduling testbed. The testbed permits planners to evaluate optimal scheduling time intervals, calculate resource usage, and to generate long and medium range plans. Graphical displays of activities, constraints, and plans are an important feature of the system. High-level scheduling strategies using rule based and neural net approaches were implemented.

Miller, Glenn↗
NASA NTRS1987

Constraint-based stereo matching

The major difficulty in stereo vision is the correspondence problem that requires matching features in two stereo images. Researchers describe a constraint-based stereo matching technique using local geometric constraints among edge segments to limit the search space and to resolve matching ambiguity. Edge segments are used as image features for stereo matching. Epipolar constraint and individual edge properties are used to determine possible initial matches between edge segments in a stereo image pair. Local edge geometric attributes such as continuity, junction structure, and edge neighborhood relations are used as constraints to guide the stereo matching process. The result is a locally consistent set of edge segment correspondences between stereo images. These locally consistent matches are used to generate higher-level hypotheses on extended edge segments and junctions to form more global contexts to achieve global consistency.

Kuan, D. T.↗
NASA NTRS1989

Mars Rover Sample Return aerocapture configuration design and packaging constraints

This paper discusses the aerodynamics requirements, volume and mass constraints that lead to a biconic aeroshell vehicle design that protects the Mars Rover Sample Return (MRSR) mission elements from launch to Mars landing. The aerodynamic requirements for Mars aerocapture and entry and packaging constraints for the MRSR elements result in a symmetric biconic aeroshell that develops a L/D of 1.0 at 27.0 deg angle of attack. A significant problem in the study is obtaining a cg that provides adequate aerodynamic stability and performance within the mission imposed constraints. Packaging methods that relieve the cg problems include forward placement of aeroshell propellant tanks and incorporating aeroshell structure as lander structure. The MRSR missions developed during the pre-phase A study are discussed with dimensional and mass data included. Further study is needed for some missions to minimize MRSR element volume so that launch mass constraints can be met.

Lawson, Shelby J.↗
NASA NTRS1989

Performance constraints and compensation for teleoperation with delay

A classical control perspective is used to characterize performance constraints and evaluate compensation techniques for teleoperation with delay. Use of control concepts such as open and closed loop performance, stability, and bandwidth yield insight to the delay problem. Teleoperator performance constraints are viewed as an open loop time delay lag and as a delay-induced closed loop bandwidth constraint. These constraints are illustrated with a simple analytical tracking example which is corroborated by a real time, 'man-in-the-loop' tracking experiment. The experiment also provides insight to those controller characteristics which are unique to a human operator. Predictive displays and feedforward commands are shown to provide open loop compensation for delay lag. Low pass filtering of telemetry or feedback signals is interpreted as closed loop compensation used to maintain a sufficiently low bandwidth for stability. A new closed loop compensation approach is proposed that uses a reactive (or force feedback) hand controller to restrict system bandwidth by impeding operator inputs.

Mclaughlin, J. S.↗
NASA NTRS1990

Optimal control of singularly perturbed nonlinear systems with state-variable inequality constraints

The established necessary conditions for optimality in nonlinear control problems that involve state-variable inequality constraints are applied to a class of singularly perturbed systems. The distinguishing feature of this class of two-time-scale systems is a transformation of the state-variable inequality constraint, present in the full order problem, to a constraint involving states and controls in the reduced problem. It is shown that, when a state constraint is active in the reduced problem, the boundary layer problem can be of finite time in the stretched time variable. Thus, the usual requirement for asymptotic stability of the boundary layer system is not applicable, and cannot be used to construct approximate boundary layer solutions. Several alternative solution methods are explored and illustrated with simple examples.

Calise, A. J.↗