Search NASA⌕ Search

SEARCH · Search NASA

Results for “Crystalline systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

The vapor pressures of solid and liquid ozone

Vapor pressures of solid and liquid ozone have been measured over a temperature range 87 to below 66 K. The experiment was performed under flow conditions, and the gas was analyzed by a precision mass spectrometer system. In the range of solid ozone two forms, supercooled and crystalline ozone, were found. A least-square fit of the data for crystalline ozone resulted in the equation log P(torr) = A + B/T, where A = 10.460 and B = -1021.6. The estimated uncertainty of the data is + or - 1.0 percent. A triple-point temperature of 79.6 + or - 0.3 K was found where supercooled and crystalline ozone data intersect.

Hanson, David↗
NASA NTRSDate not supplied

High Resolution Imaging and Analysis of Terrestrial Impact Glass: Amorphous Materials, Phyllosilicates and Everything in Between

Introduction: Impact cratering is one of the most ubiquitous geologic processes shaping the surface of all solid bodies in our solar system. Impacts are also a major source of clay minerals, poorly crystalline clay-like phases and amorphous (i.e., lacking long-range atomic order) materials on Earth and Mars. Phyllosilicates and amorphous materials have consistently formed a major component (~20-70 wt%) of every single drilled rock and soil sample in Gale Crater on Mars, as determined by the CheMin instrument on Curiosity. The origin of the amorphous component is speculative, but could be primary impact or volcanic-produced glass(es) deposited via aeolian or fluvial processes, secondary aqueous alteration products or chemical precipitates; it is likely to be a combination of all three possibilities. Efforts to determine the composition of these materials across the rover’s traverse through Gale Crater are ongoing. Naturally occurring amorphous phases are found in a variety of environments on Earth, and terrestrial analogue studies may help shed light on how they may have formed on Mars. Primary and altered impact glass are likely widespread on Mars and may have contributed to the amorphous component found throughout Gale Crater. In its pristine, unaltered state, impact glass (i.e., melt glass) is considered amorphous. However, truly unaltered glass is rarely preserved in crater fill impactites as it quickly alters in the post-impact environ-ment, commonly forming a mixture of hydrated aluminosilicate phases whose structures are not always discernable at the microscale (i.e., they may be amorphous or contain short-range order). These phases are part of an incredibly complex group of materials; differences in their composition and crystalline structure (or lack thereof) and genetic relationship to the more well-crystalline clay minerals are often only discernable at the nanoscale, beyond the resolution of traditional X-ray diffractometers (XRD) and scanning electron microscopes/microprobes (SEM/EPMA) alone. In this contribution, we summarize recent results from ongoing characterization of clay minerals, poorly crystalline clay-like phases, and amorphous materials preserved in altered terrestrial impact glass from the Chicxulub (~66 Ma) and Ries (~15 Ma) impact structures. This work has been performed using a combination of high-resolution transmission electron microscopy (HR-TEM), SEM, microprobe/EPMA, Raman spectroscopy and XRD.

Impact crater↗
NASA NTRS2001

Plant Growth Experiments in Zeoponic Substrates: Applications for Advanced Life Support Systems

A zeoponic plant-growth system is defined as the cultivation of plants in artificial soils, which have zeolites as a major component (Allen and Ming, 1995). Zeolites are crystalline, hydrated aluminosilicate minerals that have the ability to exchange constituent cations without major change of the mineral structure. Recently, zeoponic systems developed at the National Aeronautics and Space Administration (NASA) slowly release some (Allen et at., 1995) or all of the essential plant-growth nutrients (Ming et at., 1995). These systems have NH4- and K-exchanged clinoptilolite (a natural zeolite) and either natural or synthetic apatite (a calcium phosphate mineral). For the natural apatite system, Ca and P were made available to the plant by the dissolution of apatite. Potassium and NH4-N were made available by ion-exchange reactions involving Ca(2+) from apatite dissolution and K(+) and NH4(+) on zeolitic exchange sites. In addition to NH4-N, K, Ca, and P, the synthetic apatite system also supplied Mg, S, and other micronutrients during dissolution (Figure 1). The overall objective of this research task is to develop zeoponic substrates wherein all plant growth nutrients are supplied by the plant growth medium for several growth seasons with only the addition of water. The substrate is being developed for plant growth in Advanced Life Support (ALS) testbeds (i.e., BioPLEX) and microgravity plant growth experiments. Zeoponic substrates have been used for plant growth experiments on two Space Shuttle flight experiments (STS-60; STS-63; Morrow et aI., 1995). These substrates may be ideally suited for plant growth experiments on the International Space Station and applications in ALS testbeds. However, there are several issues that need to be resolved before zeoponics will be the choice substrate for plant growth experiments in space. The objective of this paper is to provide an overview on recent research directed toward the refinement of zeoponic plant growth substrates.

Ming, Douglas W.↗
NASA NTRS2006

New Optical Constants for Amorphous and Crystalline H2O-ice and H2O-mixtures.

We will present the products of new laboratory measurements of ices relevant to Trans-Neptunian Objects. We have calculated the real and imaginary indices of refraction for amorphous and crystalline H2O-ice and also H2O-rich ices containing other molecular species. We create ice samples by condensing gases onto a cold substrate. We measure the thickness of the sample by reflecting a He-Ne laser off of the sample and counting interference fringes as it grows. We then collect transmission spectra of the samples in the wavelength range from 0.7-22 micrometers. Using the thickness and the transmission spectra of the ice we calculate the imaginary part of the index of refraction. We then use a Kramers-Kronig calculation to calculate the real part of the index of refraction (Berland et al. 1994; Hudgins et al. 1993). These optical constants can then be used to create model spectra for comparison to spectra from Solar System objects, including TNOs. We will summarize the difference between the amorphous and crystalline H2O-ice spectra. These changes include weakening of features and shifting of features to shorter wavelength. One important result is that the 2 pm feature is stronger in amorphous H2O ice than it is in crystalline H2O-ice. We will also discuss the changes seen when H2O is mixed with other components, including CO2, CH4, HCN, and NH3 (Bernstein et al. 2005; Bernstein et al. 2006).

Mastrapa, Rachel↗
NASA NTRS1993

Inter- and intra-crystalline oxygen isotope distribution of fassaites in Allende CAI

Calcium, aluminum-rich inclusions (CAI's) from carbonaceous chondrite are believed to be among the first solids to have formed in the early solar system and thus to preserve a record of conditions and processes that prevailed early in the solar nebula. We have measured inter- and intra- crystalline oxygen isotope distribution of fassaite in Type B1 CAI of Allende meteorite. Secondary ion mass spectrometry (SIMS) using negative Au primary ion was applied to in situ oxygen isotope ratio analysis on a polished thin section of the CAI. Present data indicate that O isotope composition is homogeneous inside of fassaite grains as well as among grains in the HN3-1 CAI, and that the delta(exp 18) O value (-24.14 percent relative to SMOW) determined previously could be applied to most fassaite grains. The results suggest that most fassaite grains are preexisting solids like spinel grains.

Yurimoto, Hisayoshi↗
NASA NTRS1987

Thermoplastic matrix composites - LARC-TPI, polyimidesulfone and their blends

Composites were fabricated from unidirectional unsized AS-4 carbon fiber and two baseline polyimides: benzophenone dianhydride-3,3'-diaminodiphenylsulfone (PISO2) and benzophenone dianhydride-3,3'-diaminobenzophenone (LARC-TPI). In addition, each polymer solution prior to prepregging was doped with various amounts of crystalline LARC-TPI powder to enhance melt flow during press molding. The 2:1, 1:1, and 1:2 ratios of crystalline to amorphous resin, respectively, were studied in the LARC-TPI system and the 1:2 ratio in the PISO2 system. Matrix characterization, prepreg fabrication/characterization and composite fabrication and physical/mechanical properties are described. The latter include three point short beam shear and flexure, dry and wet, as well as fracture toughness properties in selected compositions.

Johnston, Norman J.↗
NASA NTRS1991

Glass formation and crystallization in high-temperature glass-ceramics and Si3N4

The softening of glassy grain boundaries in ceramic matrix composites and Si3N4 at high temperatures reduces mechanical strength and the upper-use temperature. By crystallizing this glass to a more refractory crystalline phase, a material which performs at higher temperatures may result. Three systems were examined: a cordierite composition with ZrO2 as a nucleating agent; celsian compositions; and yttrium silicate glasses both in bulk and intergranular in Si3N4. For the cordierite compositions, a series of metastable phases was obtained. The crystallization of these compositions was summarized in terms of metastable ternary isothermal sections. Zircon formed at the expense of ZrO2 and spinel. In SiC composites, the transformations were slower. In celsian, two polymorphs were crystallized. One phase, hexacelsian, which always crystallized, even when metastable, had an undesirable volume change. The other phase, celsian, was very difficult to crystallize. In yttrium silicate bulk glasses, similar in composition to the intergranular glass in Si3N4, a number of polymorphs of Y2Si2O7 were crystallized. The conditions under which these polymorphs formed are compared with crystallization in Si3N4.

Drummond, Charles H., III↗
NASA NTRSDate not supplied

TEM and XRD Investigation of Impact Glass Alteration Products: Amorphous Materials, Phyllosilicates and Everything in Between

Impact cratering is one of the most ubiquitous geologic processes shaping the surface of all solid bodies in our solar system. Impacts are also a major source of clay minerals and poorly crystalline, clay-like materials on Earth and Mars[1,2].These phyllosilicates and related clay-like phases comprise an incredibly complex group of materials, and their characterization, even in controlled laboratory settings, remains a challenging endeavor. The nature and origin of clay minerals and amorphous materials on Mars, which form a major component (~20-70 wt %) of rock and soil samples in Gale Crater as determined by the CheMin instrument on Curiosity, have remained ambiguous[3]. These amorphous phases likely fall on a spectrum between pristine volcanic and/or impact-produced primary materials and clay minerals and related phases formed from aqueous alteration. Amorphous materials are common weathering products in terrestrial sediments, soils, and paleosols [e.g., 4,5].Primary impact materials (glass, melt rocks)are comparable in some ways to those generated volcanically [6], and so it may be possible that an amorphous component is preserved within altered impactites. There are hundreds of thousands of impact craters on Mars, and Curiosity and Perseverance are currently exploring ancient impact craters. We hypothesize that the sediments and lithologies in Gale and Jezero Craters and elsewhere contain altered impact products; it is therefore important to better understand the composition and structure of these materials. Here we present the first results from a study characterizing materials produced from impact glass alteration–clay minerals, poorly crystalline/amorphous materials–in terrestrial craters using Transmission Electron Microscopy (TEM), powder X-ray diffraction (pXRD)and chemical (EDS) analysis.

Impact crater↗
NASA NTRSDate not supplied

Interlaminar R-Curve Effects in Thermoplastic Composites: Experiments and Model Correlations

The interlaminar fracture behavior of thermoplastic composites under Mode-I and Mode-II static loading is investigated in this research. The material system under consideration is a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK)†. Characterization experiments were conducted to measure the load-displacement response, peak load, and propagation of delamination from a pre-implanted Kapton® insert. The Mode-I response was characterized using a double cantilever beam (DCB) test according to the ASTM D5528-22 standard. It was observed that the propagation exhibited significant resistance to delamination growth, i.e., an R-Curve effect. The test data indicated that the steady-state fracture toughness, G SS I , was approximately twice the mean initiation fracture toughness, G Ic . The Mode-II response of an end notch flexure (ENF) specimen tested according to the ASTM D7905-19 standard exhibited an unexpected stable behavior upon attaining peak load. Prior to attaining peak load, the Mode-II response exhibited some non-linearity, which may be attributed to nonlinear bulk material response, e.g., hyper-elasticity, viscoelasticity, plasticity, etc., and potentially friction at the load/support rollers and R-Curve effects. Finite element models based on the Cohesive Zone Method (CZM) and the Virtual Crack Closure Technique (VCCT) were used to predict the DCB and ENF specimen responses. DCB analysis results obtained using G SS I predicted propagation consistent with experimental data. However, results obtained with the as characterized G Ic were inaccurate in predicting delamination growth onset and peak load. ENF analysis results obtained with the as-characterized Mode-II fracture toughness, G IIc , were inaccurate in predicting the peak load and propagation. Hence, R-Curve effects were included in both DCB and ENF simulations, which enabled improved predictions. The experimentally determined Mode-I R-Curve was used for the DCB simulations, whereas an R-Curve was derived for Mode-II assuming that the change in compliance of the specimen was associated with crack growth only.

Prabhakar M Rao↗
NASA NTRSDate not supplied

Interlaminar R-Curve Effects in Thermoplastic Composites: Experiments and Model Correlations

The interlaminar fracture behavior of thermoplastic composites under Mode-I and Mode-II static loading is investigated in this research. The material system under consideration is a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK)†. Characterization experiments were conducted to measure the load-displacement response, peak load, and propagation of delamination from a pre-implanted Kapton® insert. The Mode-I response was characterized using a double cantilever beam (DCB) test according to the ASTM D5528-22 standard. It was observed that the propagation exhibited significant resistance to delamination growth, i.e., an R-Curve effect. The test data indicated that the steady-state fracture toughness, G SS I , was approximately twice the mean initiation fracture toughness, G Ic . The Mode-II response of an end notch flexure (ENF) specimen tested according to the ASTM D7905-19 standard exhibited an unexpected stable behavior upon attaining peak load. Prior to attaining peak load, the Mode-II response exhibited some non-linearity, which may be attributed to nonlinear bulk material response, e.g., hyper-elasticity, viscoelasticity, plasticity, etc., and potentially friction at the load/support rollers and R-Curve effects. Finite element models based on the Cohesive Zone Method (CZM) and the Virtual Crack Closure Technique (VCCT) were used to predict the DCB and ENF specimen responses. DCB analysis results obtained using G SS I predicted propagation consistent with experimental data. However, results obtained with the as characterized G Ic were inaccurate in predicting delamination growth onset and peak load. ENF analysis results obtained with the as-characterized Mode-II fracture toughness, G IIc , were inaccurate in predicting the peak load and propagation. Hence, R-Curve effects were included in both DCB and ENF simulations, which enabled improved predictions. The experimentally determined Mode-I R-Curve was used for the DCB simulations, whereas an R-Curve was derived for Mode-II assuming that the change in compliance of the specimen was associated with crack growth only.

Prabhakar Rao↗
NASA NTRS2024

Impact Response of Thermoplastic Composites – Experiments and Modeling

This study investigates the impact response of thermoplastic composite materials. The material system under consideration is a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK reinforced with T700G (T700/LMPAEK ). Several High Energy Dynamic Impact (HEDI) tests were performed wherein an aluminum projectile impacted T700/LMPAEK panels at different velocities. In the impact experiment studied herein, the projectile impacted the T700/LMAPEK panel at 73.2 m/s and rebounded. The ensuing damage to the T700/LMPAEK panel was characterized via ultrasonic C-scans, visualizing damage modes including matrix cracking and delaminations. Since the projectile rebounded, the fiber breakage damage mode was not evident. The impact event was modeled using a combined continuum damage mechanics and cohesive zone analysis approach with the commercially available hydrocode LS-DYNA®. The dynamic deformation and damage of the continuum, i.e., the plies in the T700/LMPAEK laminate, was modeled using a Deformation Gradient Decomposition (DGD) material model, i.e., MAT299 available within LS-DYNA. The interlaminar regions were treated as zero-thickness cohesive zones, wherein the dynamic delamination mechanics was modeled using a traction-separation formulation. Mixed-mode delamination growth was captured using the Benzegaggh-Kenane (B-K) traction-separation interpolation law. Strain-rate sensitivity of interlaminar fracture toughness was included using approximations based on published literature. The outcomes of the modeling effort are discussed herein which demonstrate good correlations with test data regarding panel deflection, panel-projectile interactions, damage modes and damage extent.

Impact modeling↗
NASA NTRS1986

Characterization of the tribological coating composition 77 wt % CaF2 - 23 wt % Li F fused to IN-750 alloy

A coating composed of 77 wt % CaF2 - 23 wt % LiF fused on IN-750 nickel-based alloy was studied using SEM, XRD, EDX, and optical microscopic methods. The surfaces examined were the as-fused coating with no subsequent treatment, the coating after ultrasonic cleaning in water, and the uncoated polished and etched metal. It was found that the coating reacts during fusion with Ti and Nb rich inclusions in the alloy. Numerous small rectangular crystallites of Ca(Ti,Nb) oxide are formed beneath an overlay of fused fluoride composition. These crystallines are stubby and appear to be embedded in the metal substrate surface. It is known from previous studies that this coating-alloy system has good tribological properties in extreme conditions, such as liquid fluorine. It has been concluded from the present study that the short firmly embedded crystalline protuberances contribute to the coating adherence and thereby to enhanced coating wear life.

Deadmore, D. L.↗
NASA NTRS1990

On diamond, graphitic and amorphous carbons in primitive extraterrestrial solar system materials

Carbon is among the most abundant elements in the universe and carbon chemistry in meteorites and comets is an important key to understanding many Solar System and interstellar processes. Yet, the mineralogical properties and interrelations between various structural forms of elemental carbon remain ambiguous. Crystalline elemental carbons include rhombohedral graphite, hexagonal graphite, cubic diamond, hexagonal diamond (i.e., lonsdaleite or carbon-2H) and chaoite. Elemental carbon also occurs as amorphous carbon and poorly graphitized (or turbostratic) carbon but of all the forms of elemental carbon only graphite is stable under physical conditions that prevail in small Solar System bodies and in the interstellar medium. The recent discovery of cubic diamond in carbonaceous chondrites and hexagonal diamond in chondritic interplanetary dust particles (IDPs) have created a renewed interest in the crystalline elemental carbons that were not formed by shock processes on a parent body. Another technique, Raman spectroscopy, confirms a widespread occurrence of disordered graphite in the Allende carbonaceous chondrite and in chondritic IDPs. Elemental carbons have also been identified by their characteristic K-edge features in electron energy loss spectra (EELS). However, the spectroscopic data do not necessarily coincide with those obtained by selected area electron diffraction (SAED). In order to interpret these data in terms of rational crystalline structures, it may be useful to consider the principles underlying electron diffraction and spectroscopic analyses. Electron diffraction depends on electron scattering, on the type of atom and the distance between atoms in a crystal lattice. Spectroscopic data are a function of the type of atom and the energy of bonds between atoms. Also, SAED is a bulk sampling technique when compared to techniques such as Raman spectroscopy or EELS. Thus, it appears that combined analyses provide contradictory results and that amorphous, or short-range ordered, carbon identified by conventional TEM imaging and SAED may show evidence for sp(3) bonds in EELS spectra. It is suggested that complex, nanometer-scale, mineralogical interrelations are common to all elemental carbons irrespective of their origin. The subsequent thermal history, or energy balance, will determine the ultimate microstructure.

Rietmeijer, Frans J. M.↗
NASA NTRS1993

A mineralized zone in Western Candor Chasma, Mars

Spectral evidence from Viking and Phobos orbiting spacecraft suggests the local development of crystalline ferric oxides in a small region within Mars' equatorial Valles Marineris canyon system. This is the same area noted for its anomalous coloration in Viking Orbiter image 583 A by McEwen. The unique hue of the region in Viking color data is due to a reduced green filter reflectance, relative to violet and red, in comparison to surrounding materials of similar albedo or average reflectance. For this reason, the region does not appear spectrally distinctive in later Survey Mission images which were acquired without the green filter. In high resolution, the spectral unit can be seen to correspond to two 20 km long depressions on the margins of Candor Mensa, a heavily eroded plateau-forming deposit on the canyon floor. Laminae are conspicuous in several places on the plateau, particularly where 15 to 20 cycles of alternating bright and dark laminae are exposed at approximately 200 meter vertical intervals. Laminae are also visible on the steep, vertically fluted cliffs to the south of this depression. Concentric laminae indicate a basis in the depression on the southeastern margin of Candor Mensa at the location of the less pronounced hue anomaly. A distinct lineation at the base of the scarp at the western end of the canyon transects mottled canyon floor deposits believed to be among the youngest in the Valles marineris. Water is implicated in the formation of the iron oxides, since the steep surfaces of layered sediments elsewhere on Candor Mensa show no evidence of unusual coloration despite the fact that these materials were deposited concurrently with the strata exposed in the depressions. This suggests that the mineralization is secondary in nature and developed locally in association with the depressions, which could have ponded surface runoff or groundwater seepage.

Geissler, P. E.↗
NASA NTRS2016

Abundant Solar Nebula Solids in Comets

Comets have been proposed to consist of unprocessed interstellar materials together with a variable amount of thermally annealed interstellar grains. Recent studies of cometary solids in the laboratory have shown that comets instead consist of a wide range of materials from across the protoplanetary disk, in addition to a minor complement of interstellar materials. These advances were made possible by the return of direct samples of comet 81P/Wild 2 coma dust by the NASA Stardust mission and recent advances in microscale analytical techniques. Isotopic studies of 'cometary' chondritic porous interplanetary dust particles (CP-IDPs) and comet 81P/Wild 2 Stardust samples show that preserved interstellar materials are more abundant in comets than in any class of meteorite. Identified interstellar materials include sub-micron-sized presolar silicates, oxides, and SiC dust grains and some fraction of the organic material that binds the samples together. Presolar grain abundances reach 1 weight percentage in the most stardust-rich CP-IDPs, 50 times greater than in meteorites. Yet, order of magnitude variations in presolar grain abundances among CP-IDPs suggest cometary solids experienced significant variations in the degree of processing in the solar nebula. Comets contain a surprisingly high abundance of nebular solids formed or altered at high temperatures. Comet 81P/Wild 2 samples include 10-40 micron-sized, refractory Ca- Al-rich inclusion (CAI)-, chondrule-, and ameboid olivine aggregate (AOA)-like materials. The O isotopic compositions of these refractory materials are remarkably similar to their meteoritic counterparts, ranging from 5 percent enrichments in (sup 16) O to near-terrestrial values. Comet 81P/Wild 2 and CP-IDPs also contain abundant Mg-Fe crystalline and amorphous silicates whose O isotopic compositions are also consistent with Solar System origins. Unlike meteorites, that are dominated by locally-produced materials, comets appear to be composed of materials that were formed across a wide swath of the early protoplanetary disk.

Messenger, S.↗