Search NASA⌕ Search

SEARCH · Search NASA

Results for “Distribution Transformer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Distributed Control Architecture for Gas Turbine Engine

The transformation of engine control systems from centralized to distributed architecture is both necessary and enabling for future aeropropulsion applications. The continued growth of adaptive control applications and the trend to smaller, light weight cores is a counter influence on the weight and volume of control system hardware. A distributed engine control system using high temperature electronics and open systems communications will reverse the growing trend of control system weight ratio to total engine weight and also be a major factor in decreasing overall cost of ownership for aeropropulsion systems. The implementation of distributed engine control is not without significant challenges. There are the needs for high temperature electronics, development of simple, robust communications, and power supply for the on-board electronics.

Dennis Culley↗
NASA NTRS1992

Extreme value statistics analysis of fracture strengths of a sintered silicon nitride failing from pores

Statistical analysis and correlation between pore-size distribution and fracture strength distribution using the theory of extreme-value statistics is presented for a sintered silicon nitride. The pore-size distribution on a polished surface of this material was characterized, using an automatic optical image analyzer. The distribution measured on the two-dimensional plane surface was transformed to a population (volume) distribution, using the Schwartz-Saltykov diameter method. The population pore-size distribution and the distribution of the pore size at the fracture origin were correllated by extreme-value statistics. Fracture strength distribution was then predicted from the extreme-value pore-size distribution, usin a linear elastic fracture mechanics model of annular crack around pore and the fracture toughness of the ceramic. The predicted strength distribution was in good agreement with strength measurements in bending. In particular, the extreme-value statistics analysis explained the nonlinear trend in the linearized Weibull plot of measured strengths without postulating a lower-bound strength.

Chao, Luen-Yuan↗
NASA NTRS1984

Spectral characteristics and meridional variations of energy transformations during the first and second special observation periods of FGGE

The global features and meridional spectral energy transformation variations of the first and second special observation periods of the First Global GARP Experiment (FGGE) are investigated, together with the latitudinal distribution of the kinetic energy balance. Specific seasonal characteristics are shown by the spectral distributions of the global transformations between (1) zonal mean and eddy components of the available potential energy, (2) the zonal mean and eddy components of the kinetic energy, and (3) the available potential energy and the kinetic energy. Maximum kinetic energy production is found to occur at subtropical latitudes, with a secondary maximum at higher middle latitudes. Between these two regions, there is another region characterized by the adiabatic destruction of kinetic energy above the lower troposphere.

Kung, E. C.↗
NASA NTRS1991

Cometary water-group ions in the region surrounding Comet Giacobini-Zinner - Distribution functions and bulk parameter estimates

The bulk parameters (number density and thermal energy density) of cometary water-group ions in the region surrounding Comet Giacobini-Zinner have been derived using data from the EPAS instrument on the ICE spacecraft. The derivation is based on the assumption that the pick-up ion distribution function is isotropic in the frame of the bulk flow, an approximation which has previously been shown to be reasonable within about 400,000 km of the comet nucleus along the spacecraft trajectory. The transition between the pick-up and mass-loaded regions occurs at the cometary shock, which was traversed at a cometocentric distance of about 100,000 km along the spacecraft track. Examination of the ion distribution functions in this region, transformed to the bulk flow frame, indicates the occurrence of a flattened distribution in the vicinity of the local pick-up speed, and a steeply falling tail at speeds above, which may be approximated as an exponential in ion speed.

Staines, K.↗
NASA NTRS1987

Space station electrical power distribution analysis using a load flow approach

The space station's electrical power system will evolve and grow in a manner much similar to the present terrestrial electrical power system utilities. The initial baseline reference configuration will contain more than 50 nodes or busses, inverters, transformers, overcurrent protection devices, distribution lines, solar arrays, and/or solar dynamic power generating sources. The system is designed to manage and distribute 75 KW of power single phase or three phase at 20 KHz, and grow to a level of 300 KW steady state, and must be capable of operating at a peak of 450 KW for 5 to 10 min. In order to plan far into the future and keep pace with load growth, a load flow power system analysis approach must be developed and utilized. This method is a well known energy assessment and management tool that is widely used throughout the Electrical Power Utility Industry. The results of a comprehensive evaluation and assessment of an Electrical Distribution System Analysis Program (EDSA) is discussed. Its potential use as an analysis and design tool for the 20 KHz space station electrical power system is addressed.

Emanuel, Ervin M.↗
NASA NTRS1986

Comparative energetics of the observed and simulated global circulation during the special observing periods of FGGE

Energetics of the observed and simulated global circulation are evaluated in the zonal spectral domain for the special observing periods of FGGE. The study utilizes GLA analyses of FGGE observational data and parallel simulation experiments. There are noticeable differences in energy transformations between the observation and simulation during SOP-1. These include the baroclinic conversion C(n) by the zonal mean motion and short-wave disturbances, and the nonlinear wave-wave interaction L(n) at the long and short waves. The energy transformations of the short-wave disturbances are much more intense in the simulated circulation than in the observation. However, good agreement is noted in the conversion and dissipation of kinetic energy in the large- and cyclone-wave range n = 1-10. Spectral distributions of global energy transformations at the long- and cyclone-wave range indicate that the SOP-2 simulation agrees more closely with the observed fields than the SOP-1 simulation. Other pertinent points of energetics diagnosis are also included in the discussion.

Kung, E. C.↗
NASA NTRS1993

Biasing and hierarchical statistics in large-scale structure

In this paper we consider the consequences for galaxy formation of an arbitrary, effectively local biasing transformation of a hierarchical underlying matter distribution. We show that a general form of such a transformation preserves the hierarchical properties and the shape of the dispersion in the limit of small fluctuations, i.e., on large scales, although the values of the hierarchical amplitudes may change arbitrarily. We present expressions for the induced hierarchical amplitudes S(g,j) of the galaxy distribution in terms of the matter amplitudes S(j) and biasing parameters for j = 3-7. For higher order correlations, j greater than 2, restricting to a linear bias is not a consistent approximation even at very large scales. To draw any conclusions from the galaxy distribution about matter correlations of order j, properties of biasing must be specified completely to order j - 1.

Fry, J. N.↗
NASA NTRS1980

Shaped reflector antenna analysis using the Jacobi-Bessel series

A vector radiation integral is derived for an offset shaped reflector illuminated by an arbitrarily located and oriented source. A procedure for expressing the integral in terms of a series of the Fourier transforms of an effective aperture distribution is discussed. The Jacobi-Bessel series is used to evaluate the Fourier transforms. Numerical results are presented for different reflector configurations and source locations.

Rahmat-Samii, Y.↗
NASA NTRS2017

Linear Transformer Drivers for Z-pinch Based Propulsion

The MSFC/UAH team has been developing of a novel power management and distribution system called a Linear Transformer Driver (LTD). LTD's hold the promise of dramatically reducing the required mass to drive a z-pinch by replacing the capacitor banks which constitute half the mass of the entire system. The MSFC?UAH tea, is developing this technology in hope of integrating it with the Pulsed Fission Fusion (PuFF) propulsion concept. High-Voltage pulsed power systems used for Z-Pinch experimentation have in the past largely been based on Marx Generators. Marx generators deliver the voltage and current required for the Z-Pinch, but suffer from two significant drawbacks when applied to a flight system: they are very massive, consisting of high-voltage capacitor banks insulated in oil-filled tanks and they do not lend themselves to rapid pulsing. The overall goal of Phase 2 is to demonstrate the construction of a higher voltage stack from a number of cavities each of the design proven in Phase 1 and to characterize and understand the techniques for designing the stack. The overall goal of Phase 3 is to demonstrate the feasibility of constructing a higher energy cavity from a number of smaller LTD stacks, to characterize and understand the way in which the constituent stacks combine, and to extend this demonstration LTD to serve as the basis for a 64 kJ pulse generator for Z-Pinch experiments.

Adams, Robert↗
NASA NTRS1975

The state of meteoritic material on the moon

Velocity distributions obtained from earth-based meteor observations and corrected to constant meteoroid mass are transformed to meteoroid impact velocity distributions at the moon. Average velocities at the moon thus obtained range from 13 to 18 km/sec. This information is then combined with impact heating estimates to determine the amounts of resident lunar material and incoming meteoritic material that is melted or vaporized. It is found that about 5% of the resulting melt and about 25% of the impact generated vapor should be of meteoritic content. The uncertainties in these estimates are rather large, however, because of uncertainties in the various experimental results required to establish the parameters used in this analysis. The impact generated melts and impact generated vapor deposits, if the latter can be found, should provide additional means for chemically separating out the meteoritic component in the lunar soil.

Zook, H. A.↗
NASA NTRS1986

Description of a 20 Kilohertz power distribution system

A single phase, 440 VRMS, 20 kHz power distribution system with a regulated sinusoidal wave form is discussed. A single phase power system minimizes the wiring, sensing, and control complexities required in a multi-sourced redundantly distributed power system. The single phase addresses only the distribution link; mulitphase lower frequency inputs and outputs accommodation techniques are described. While the 440 V operating potential was initially selected for aircraft operating below 50,000 ft, this potential also appears suitable for space power systems. This voltage choice recognizes a reasonable upper limit for semiconductor ratings, yet will direct synthesis of 220 V, 3 power. A 20 kHz operating frequency was selected to be above the range of audibility, minimize the weight of reactive components, yet allow the construction of single power stages of 25 to 30 kW. The regulated sinusoidal distribution system has several advantages. With a regulated voltage, most ac/dc conversions involve rather simple transformer rectifier applications. A sinusoidal distribution system, when used in conjunction with zero crossing switching, represents a minimal source of EMI. The present state of 20 kHz power technology includes computer controls of voltage and/or frequency, low inductance cable, current limiting circuit protection, bi-directional power flow, and motor/generator operating using standard induction machines. A status update and description of each of these items and their significance is presented.

Hansen, I. G.↗
NASA NTRS1986

Description of a 20 kilohertz power distribution system

A single phase, 440 VRMS, 20 kHz power distribution system with a regulated sinusoidal wave form is discussed. A single phase power system minimizes the wiring, sensing, and control complexities required in a multi-sourced redundantly distributed power system. The single phase addresses only the distribution links multiphase lower frequency inputs and outputs accommodation techniques are described. While the 440 V operating potential was initially selected for aircraft operating below 50,000 ft, this potential also appears suitable for space power systems. This voltage choice recognizes a reasonable upper limit for semiconductor ratings, yet will direct synthesis of 220 V, 3 power. A 20 kHz operating frequency was selected to be above the range of audibility, minimize the weight of reactive components, yet allow the construction of single power stages of 25 to 30 kW. The regulated sinusoidal distribution system has several advantages. With a regulated voltage, most ac/dc conversions involve rather simple transformer rectifier applications. A sinusoidal distribution system, when used in conjunction with zero crossing switching, represents a minimal source of EMI. The present state of 20 kHz power technology includes computer controls of voltage and/or frequency, low inductance cable, current limiting circuit protection, bi-directional power flow, and motor/generator operating using standard induction machines. A status update and description of each of these items and their significance is presented.

Hansen, I. G.↗
NASA NTRS1971

Frequency domain stability criteria for distributed nonlinear sampled-data systems.

Popov-type sufficient conditions are presented for the absolute stability of a class of closed loop sampled-data systems. The closed loop system consists of a linear distributed element, a feedback controller (linear or nonlinear), a sampler, and possibly a zero-order hold circuit. The distributed element is assumed to be finite Hankel transformable, and such that its dynamics can be represented by a transfer function which is the ratio of the multiple (Laplace and finite Hankel) transforms of output and input. The input is assumed to be distributed. The stability criterion presented here parallels the criterion for distributed systems that are finite Fourier transformable. An example is given to illustrate the applications of the stability criterion.

Nagarajan, N.↗
NASA NTRS1995

Three-dimensional object tracking system and method employing plural sensors and plural processors for performing parallel processing

A multiple sensor/multiple processor 3-D tracking system includes multiple sensor (camera) and DSP combinations and a controller connected so as to create a parallel computer from the multiple DSPs. The camera/DSP combinations and the controller are connected together to form a ring. For 3-D position measurement and tracking applications, each camera/DSP combination is programmed with an identical program to function as a node in a true parallel computer, and the transformation equations are solved in a distributed fashion using the entire parallel machine. The distributed processor processes the camera x and y point measurements in a distributed and parallel fashion to yield a solution to the coordinate transformation equations much more quickly than is possible with multiple camera/DSP combinations and a single processor.

Welch, Sharon S.↗
NASA NTRS2010

A Study of Cirrus Ice Particle Size Distribution Using TC4 Observations

An analysis of two days of in situ observations of ice particle size spectra, in convectively generated cirrus, obtained during NASA s Tropical Composition, Cloud, and Climate Coupling (TC4) mission is presented. The observed spectra are examined for their fit to the exponential, gamma, and lognormal function distributions. Characteristic particle size and concentration density scales are determined using two (for the exponential) or three (for the gamma and lognormal functions) moments of the spectra. It is shown that transformed exponential, gamma, and lognormal distributions should collapse onto standard curves. An examination of the transformed spectra, and of deviations of the transformed spectra from the standard curves, shows that the lognormal function provides a better fit to the observed spectra.

Tian, Lin↗
NASA NTRS2011

Wind and Temperature Spectrometry of the Upper Atmosphere in Low-Earth Orbit

Wind and Temperature Spectrometry (WATS) is a new approach to measure the full wind vector, temperature, and relative densities of major neutral species in the Earth's thermosphere. The method uses an energy-angle spectrometer moving through the tenuous upper atmosphere to measure directly the angular and energy distributions of the air stream that enters the spectrometer. The angular distribution gives the direction of the total velocity of the air entering the spectrometer, and the energy distribution gives the magnitude of the total velocity. The wind velocity vector is uniquely determined since the measured total velocity depends on the wind vector and the orbiting velocity vector. The orbiting spectrometer moves supersonically, Mach 8 or greater, through the air and must point within a few degrees of its orbital velocity vector (the ram direction). Pointing knowledge is critical; for example, pointing errors 0.1 lead to errors of about 10 m/s in the wind. The WATS method may also be applied without modification to measure the ion-drift vector, ion temperature, and relative ion densities of major ionic species in the ionosphere. In such an application it may be called IDTS: Ion-Drift Temperature Spectrometry. A spectrometer-based coordinate system with one axis instantaneously pointing along the ram direction makes it possible to transform the Maxwellian velocity distribution of the air molecules to a Maxwellian energy-angle distribution for the molecular flux entering the spectrometer. This implementation of WATS is called the gas kinetic method (GKM) because it is applied to the case of the Maxwellian distribution. The WATS method follows from the recognition that in a supersonic platform moving at 8,000 m/s, the measurement of small wind velocities in the air on the order of a few 100 m/s and less requires precise knowledge of the angle of incidence of the neutral atoms and molecules. The same is true for the case of ion-drift measurements. WATS also provides a general approach that can obtain non-equilibrium distributions as may exist in the upper regions of the thermosphere, above 500 km and into the exosphere. Finally, WATS serves as a mass spectrometer, with very low mass resolution of roughly 1 part in 3, but easily separating atomic oxygen from molecular nitrogen.

Herrero, Federico↗
NASA NTRS1991

Detection of reflector surface from near field phase measurements

The deviation of a reflector antenna surface from a perfect parabolic shape causes degradation of the performance of the antenna. The problem of determining the shape of the reflector surface in a reflector antenna using near field phase measurements is not a new one. A recent issue of the IEEE tansactions on Antennas and Propagation (June 1988) contained numerous descriptions of the use of these measurements: holographic reconstruction or inverse Fourier transform. Holographic reconstruction makes use of measurement of the far field of the reflector and then applies the Fourier transform relationship between the far field and the current distribution on the reflector surface. Inverse Fourier transformation uses the phase measurements to determine the far field pattern using the method of Kerns. After the far field pattern is established, an inverse Fourier transform is used to determine the phases in a plane between the reflector surface and the plane in which the near field measurements were taken. These calculations are time consuming since they involve a relatively large number of operations. A much faster method can be used to determine the position of the reflector. This method makes use of simple geometric optics to determine the path length of the ray from the feed to the reflector and from the reflector to the measurement point. For small physical objects and low frequencies, diffraction effects have a major effect on the error, and the algorithm provides incorrect results. It is believed that the effect is less noticeable for large distortions such as antenna warping, and more noticeable for small, localized distortions such as bumps and depressions such as might be caused by impact damage.

Ida, Nathan↗