Search NASA⌕ Search

SEARCH · Search NASA

Results for “Drag Coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Drag Coefficient Analysis of Arbitrary Fragment Geometry with Emphasis on Meshing Sensitivity Studies.

This report characterizes Mach number effects in the hypersonic range from Mach 3 to Mach 7 for an arbitrary, computationally generated fragment. Force and moment coefficients in the x, y, z direction were successfully obtained and resulting trends were compared with theoretical expectations. Three orientations were tested in the form of unit vectors: [1,0,0], [0,1,0], and [0,0,1]; these represent the i, j, k principle axes. The final results ultimately showcased a trend very similar to that shown in previous literature — drag coefficients for a given orientation decreased with increasing Mach number by a very small amount in the hypersonic range. It was therefore concluded that the aerodynamic quantities used to obtain the fragment trajectory at low hypersonic Mach numbers (such as Mach 3) can be used to characterize the aerodynamic qualities at higher hypersonic Mach numbers (Mach 5, 7) with a reasonably small margin. A sensitivity study was also conducted which ultimately defined drag effects as a result of changing grid spacing and normal extrusion parameters for the unstructured tetrahedral mesh used in the simulation. Further work can be done in the form of experimental validation, specifically with regards to wind tunnels and ballistic range testing. Error can be reduced by testing more mesh variabilities and capturing a larger amount of fragment orientations. The results for force and moment characteristics dependent on meshing parameters and high Mach numbers are satisfactory and consistent with expected trends.

42 ENGINEERING↗
NASA NTRS2003

Flight Reconstruction of the Mars Pathfinder Disk-Gap-Band Parachute Drag Coefficient

On July 4, 1997, the Mars Pathfinder (MPF) mission successfully landed on Mars. The entry, descent, and landing (EDL) scenario employed the use of a Disk-Gap-Band parachute design to decelerate the Lander. Flight reconstruction of the entry using MPF flight accelerometer data revealed that the MPF parachute decelerated faster than predicted. In the summer of 2003, the Mars Exploration Rover (MER) mission will send two Landers to the surface of Mars arriving in January 2004. The MER mission utilizes a similar EDL scenario and parachute design as that employed by MPF. As a result, characterizing the degree of underperformance of the MPF parachute system is critical for the MER EDL trajectory design. This paper provides an overview of the methodology utilized to estimate the MPF parachute drag coefficient as experienced on Mars.

Desai, Prasun↗
NASA NTRS1993

Roughness of Weddell Sea ice and estimates of the air-ice drag coefficient

Snow surface, ice surface, and ice underside roughness computed from 47 surface elevation profiles collected during a transect of the Weddell Sea are reported. Roughness spectra for all three surfaces and for both deformed and undeformed ice roll off roughly as k exp -1 when the wavenumber k is between 0.1 and 3 rad/m. The snow surface and underside spectra roll off somewhat faster than k exp -1, and the ice surface spectra roll off somewhat slower than k exp -1. It is argued that the excess spectral intensity at high wavenumbers in the Antarctic ice surface spectra results from the small-scale roughness that the ice sheet had on consolidation. The snow surface spectra are used to compute a roughness scale that parameterizes the air-ice momentum coupling and makes it possible to estimate the neutral stability drag coefficient referenced to a height of 10 m, C sub DN10. Typical C sub DN10 values are 1.1-1.4 x 10 exp -3 over undeformed ice and 1.3-1.8 x 10 exp -3 over deformed ice.

Andreas, Edgar L.↗
NASA NTRS1978

Section drag coefficients from pressure probe transverses of a wing wake at low speeds

An in-flight wing wake section drag investigation was conducted using traversing pitot and static probes. The primary objective was to develop measurement techniques and improve the accuracy of in-flight wing profile drag measurements for low values of dynamic pressure and Reynolds number. Data were obtained on a sailplane for speeds from about 40 knots to 125 knots at chord Reynolds numbers between 1,000,000 and 3,000,000. Tests were conducted with zero flap deflection, deflected flaps, and various degrees of surface roughness, and for smooth and rough atmospheric conditions. Several techniques were used to increase data reliability and to minimize certain bias errors. A discussion of the effects of a total pressure probe in a pressure gradient, and the effects of discrete turbulence levels, on the data presented and other experimental results is also included.

Montoya, L. C.↗
NASA NTRS1973

The effect of thermal stratification and evaporation on geostrophic drag coefficient in the atmospheric boundary layer

It is shown that the fields of velocity, eddy viscosity, potential temperature, and specific humidity in a planetary boundary layer are decoupled by the introduction of a free parameter, Q, which combines the effects of thermal and humidity stratification. Solutions of the whole system are shown to be obtainable by the method of trial and error on Q. Results show good agreement when both the thermal and humidity stratification are accounted for.

Yeh, G.-T.↗
NASA NTRS1975

Drag coefficients for astronomical observatory satellites

The first experimental European communications satellite Symphonie is a geostationary satellite. The satellite is designed and built in a joint project by French and German aerospace firms. A description is given of the basic technical concept of the satellite. The apogee motor is discussed along with the satellite stabilization system. The stabilization system provides a three-axis positional stabilization and an orbital stabilization. Attention is given to the spin stabilization phase, the sensors employed, the approache used for orbital correction maneuvers, and the conduction of simulation tests on the ground.

Williams, R. R.↗