Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dynamic contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructural Passivation of Patterned Al 2 O 3 Back Contacts on CdS/CdTe Solar Cells

Abstract Patterned aluminum oxide (Al 2 O 3 ) back contact on cadmium telluride (CdTe) solar cells can effectively mitigate the loss of the majority carriers while retaining the passivation benefits for minority carriers. This study investigates the impact of the point‐contact geometry on cell performance, where the spacing of the microholes is systematically varied at a constant microhole diameter (≈16 µm). Microhole arrays are created on an evaporated Al 2 O 3 layer (≈30 nm) on CdTe using laser‐beam lithography and selective wet etching processes. Comparative analysis indicates a significant decrease in fill factor (FF) and short‐circuit current ( I SC ) when the contact fraction falls below 30%, likely due to the Al 2 O 3 barrier impeding majority carriers. Above this fraction, FF and I SC are comparable to those of baseline CdTe cells without Al 2 O 3 . Open‐circuit voltage ( V OC ) shows a gradual decrease as Al 2 O 3 coverage is reduced but exhibits a slight increase (<15 mV) when the contact fraction exceeds 30%. Cathodoluminescence (CL) characterization reveals that significantly improved radiative recombination occurs within the CdTe grain bulk with Al 2 O 3 , whereas this effect on grain boundaries is minimal. The findings imply complex local carrier dynamics in the patterned back‐contact region, closely tied to the microstructural properties of CdTe‐based solar cells.

Roy, Etee Kawna↗
DOE OSTI2023

Dynamical responses of constrained pipe conveying fluids and its dependence on the modeling of the contact force

Accurately modeling the impact force used in the analysis of loosely constrained cantilevered pipes conveying fluid is imperative. If little information is known of the motion-limiting constraints used in experiments, the analysis of the system may yield inaccurate predictions. Here in this work, multiple forcing representations of the impact force are defined and analyzed for a cantilevered pipe that conveys fluid. Depending on the representation of the impact force, the dynamics of the pipe can vary greatly when only the stiffness of the constraints is known from experiments. Three gap sizes of the constraints are analyzed, and the representation of the impact force used to analyze the system is found to significantly affect the response of the pipe at each gap size. An investigation on the effects of the vibro-impact force representation is performed through using basin of attraction analysis and nonlinear characterization of the system’s response.

42 ENGINEERING↗
DOE OSTI2022

Tracking structural solvent reorganization and recombination dynamics following e – photoabstraction from aqueous I – with femtosecond x-ray spectroscopy and scattering

Here we present a sub-picosecond resolved investigation of the structural solvent reorganization and geminate recombination dynamics following 400 nm two-photon excitation and photodetachment of a valence p electron from the aqueous atomic solute, I–(aq). The measurements utilized time-resolved X-ray Absorption Near Edge Structure (TR-XANES) spectroscopy and X-ray Solution Scattering (TR-XSS) at the Linac Coherent Light Source x-ray free electron laser in a laser pump/x-ray probe experiment. The XANES measurements around the L 1 -edge of the generated nascent iodine atoms (I 0 ) yield an average electron ejection distance from the iodine parent of 7.4 ± 1.5 Å with an excitation yield of about 1/3 of the 0.1M NaI aqueous solution. The kinetic traces of the XANES measurement are in agreement with a purely diffusion-driven geminate iodine–electron recombination model without the need for a long-lived (I 0 :e–) contact pair. Nonequilibrium classical molecular dynamics simulations indicate a delayed response of the caging H 2 O solvent shell and this is supported by the structural analysis of the XSS data: We identify a two-step process exhibiting a 0.1 ps delayed solvent shell reorganization time within the tight H-bond network and a 0.3 ps time constant for the mean iodine–oxygen distance changes. The results indicate that most of the reorganization can be explained classically by a transition from a hydrophilic cavity with a well-ordered first solvation shell (hydrogens pointing toward I–) to an expanded cavity around I 0 with a more random orientation of the H 2 O molecules in a broadened first solvation shell.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Molecular basis for higher affinity of SARS-CoV-2 spike RBD for human ACE2 receptor

Severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2) has caused substantially more infections, deaths, and economic disruptions than the 2002-2003 SARSCoV. The key to understanding SARS-CoV-2's higher infectivity lies partly in its host receptor recognition mechanism. Experiments show that the human angiotensin converting enzyme 2 (ACE2) protein, which serves as the primary receptor for both CoVs, binds to the receptor binding domain (RBD) of CoV-2's spike protein stronger than SARS-CoV's spike RBD. The molecular basis for this difference in binding affinity, however, remains unexplained from X-ray structures. To go beyond insights gained from X-ray structures and investigate the role of thermal fluctuations in structure, we employ all-atom molecular dynamics simulations. Microseconds-long simulations reveal that while CoV and CoV-2 spike-ACE2 interfaces have similar conformational binding modes, CoV-2 spike interacts with ACE2 via a larger combinatorics of polar contacts, and on average, makes 45% more polar contacts. Correlation analysis and thermodynamic calculations indicate that these differences in the density and dynamics of polar contacts arise from differences in spatial arrangements of interfacial residues, and dynamical coupling between interfacial and non-interfacial residues. Furthermore, these results recommend that ongoing efforts to design spike-ACE2 peptide blockers will benefit from incorporating dynamical information as well as allosteric coupling effects.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Insights on the continuous representations of piecewise-smooth nonlinear systems: limits of applicability and effectiveness

Dynamical systems subject to intermittent contact are often modeled with piecewise-smooth contact forces. However, the discontinuous nature of the contact can cause inaccuracies in numerical results or failure in numerical solvers. Representing the piecewise contact force with a continuous and smooth function can mitigate these problems, but not all continuous representations may be appropriate for this use. Here, five representations used by previous researchers (polynomial, rational polynomial, hyperbolic tangent, arctangent, and logarithm-arctangent functions) are studied to determine which ones most accurately capture nonlinear behaviors including super- and subharmonic resonances, multiple solutions, and chaos. The test case is a single-DOF forced Duffing oscillator with freeplay nonlinearity, solved using direct time integration. This work intends to expand on past studies by determining the limits of applicability for each representation and what numerical problems may occur.

42 ENGINEERING↗
DOE OSTI2021

Lattice Boltzmann Modeling of Drying of Porous Media Considering Contact Angle Hysteresis

Drying of porous media is governed by a combination of evaporation and movement of the liquid phase within the porous structure. Contact angle hysteresis induced by surface roughness is shown to influence multi-phase flows, such as contact line motion of droplet, phase distribution during drainage and coffee ring formed after droplet drying in constant contact radius mode. However, the influence of contact angle hysteresis on liquid drying in porous media is still an unanswered question. Lattice Boltzmann model (LBM) is an advanced numerical approach increasingly used to study phase change problems including drying. In this paper, based on a geometric formulation scheme to prescribe contact angle, we implement a contact angle hysteresis model within the framework of a two-phase pseudopotential LBM. The capability and accuracy of prescribing and automatically measuring contact angles over a large range are tested and validated by simulating droplets sitting on flat and curved surfaces. Afterward, the proposed contact angle hysteresis model is validated by modeling droplet drying on flat and curved surfaces. Then, drying of two connected capillary tubes is studied, considering the influence of different contact angle hysteresis ranges on drying dynamics. Finally, the model is applied to study drying of a dual-porosity porous medium, where phase distribution and drying rate are compared with and without contact angle hysteresis. The proposed model is shown to be capable of dealing with different contact angle hysteresis ranges accurately and of capturing the physical mechanisms during drying in different porous media including flat and curved geometries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Spontaneous imbibition in a square tube with corner films: theoretical model and numerical simulation

Spontaneous imbibition in an angular tube with corner films is a fundamental problem in many scientific and engineering processes. In this paper, a modified interacting capillary bundle model is developed to describe the liquid imbibition dynamics in a square tube with corner films. The square tube is decomposed into several interacting sub-capillaries and the local capillary pressure in each sub-capillary is derived based on the specific shape of its meniscus. The conductance of each sub-capillary is calculated using single-phase lattice Boltzmann simulation. The modified interacting capillary bundle model and color-gradient lattice Boltzmann method are used to simulate the liquid imbibition dynamics in the square tube with different fluid properties. The predictions by the modified interacting capillary bundle model match well with the lattice Boltzmann simulation results for different conditions, demonstrating the accuracy and robustness of the interacting capillary bundle model to describe the imbibition dynamics with corner films. In addition, the interacting capillary bundle model is helpful to investigate the mechanisms during spontaneous imbibition and the influences of fluid viscosity, surface tension, wetting phase contact angle and gravity on imbibition dynamics. Finally, a universal scaling law of imbibition dynamics for the main meniscus is developed and the scaling law for arc meniscus is also analyzed.

42 ENGINEERING↗
DOE OSTI2021

Chain and Segmental Dynamics in Polymer–Nanoparticle Composites with High Nanoparticle Loading

Recent experimental and simulation studies have shown that polymer–nanoparticle (NP) composites (PNCs) with ultra-high NP loading (>50%) exhibit remarkable mechanical properties and dramatic increases in polymer glass-transition temperature, viscosity, and thermal stability compared to the bulk polymer. These deviations in macroscopic properties suggest a slowdown in both segmental and chain-scale polymer dynamics due to confinement. In this work, we examine the polymer conformations and dynamics in these PNCs using molecular dynamics simulations of both unentangled and entangled coarse-grained polymers in random-close-packed NP packings with varying polymer fill fractions. We find that the changes in the polymer dynamics depend on the number of NPs in contact with a polymer segment. Using the number of polymer–NP contacts and different polymer chain conformations as criteria for categorization, we further examine the polymer dynamics at multiple length scales to show the high level of dynamic heterogeneity in PNCs with ultra-high NP loading.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Evaluating the active site-substrate interplay between x-ray crystal structure and molecular dynamics in chorismate mutase

Designing realistic quantum mechanical (QM) models of enzymes is dependent on reliably discerning and modeling residues, solvents, and cofactors important in crafting the active site microenvironment. Interatomic van der Waals contacts have previously demonstrated usefulness toward designing QM-models, but their measured values (and subsequent residue importance rankings) are expected to be influenceable by subtle changes in protein structure. Using chorismate mutase as a case study, this work examines the differences in ligand-residue interatomic contacts between an x-ray crystal structure and structures from a molecular dynamics simulation. Select structures are further analyzed using symmetry adapted perturbation theory to compute ab initio ligand-residue interaction energies. The findings of this study show that ligand-residue interatomic contacts measured for an x-ray crystal structure are not predictive of active site contacts from a sampling of molecular dynamics frames. In addition, the variability in interatomic contacts among structures is not correlated with variability in interaction energies. However, the results spotlight using interaction energies to characterize and rank residue importance in future computational enzymology workflows.

Chemistry↗
DOE OSTI2021

Experimental Investigation of Elastodynamic Nonlinear Response of Dry Intact, Fractured and Saturated Rock

Nonlinear elastodynamic response of fractured rocks carries crucial information on fracture features that can be exploited to forecast flow properties, friction constitutive behavior and poromechanical response. Well-controlled laboratory experiments are designed to measure the nonlinear elastodynamic response of Westerly granite in three states: dry intact, dry fractured and saturated fractured. We study the effect of fracturing and saturation in modifying the elastodynamic response of the rock. Each sample is tested at a normal stress level of 15 MPa. We measure the elastodynamic response of an intact L-shaped sample of Westerly Granite subjected to normal stress oscillations of prescribed amplitudes (0.2–1 MPa) and frequencies (0.1, 1, 10 Hz). Ultrasonic waves transmitted across the sample are used to monitor the evolution of wave velocity before, during and after dynamic stressing. Furthermore, the nonlinearity of the elastodynamic response is measured in terms of: (1) the offset in normalized wave velocity; (2) the amplitude of wave velocity fluctuation during the oscillations; and (3) recovery rate of the wave velocity post-oscillation. We observe that the three nonlinearity parameters show a similar trend. Irrespective of the parameter, the nonlinearity measures higher for sample in dry-intact condition than that for dry-fractured and the saturated-fractured sample exhibits smaller nonlinearity than the dry-fractured sample. As expected, the saturated sample exhibits less nonlinearity than the dry intact and fractured samples due to the presence of interstitial fluid and the resulting increased interface stiffness. Conversely, the dry intact rock shows a higher nonlinearity than the dry fractured. We use numerical simulations to show that the presence of fracture significantly alters the strain distribution across the bulk of the sample and only the contacting asperities are highly strained, thus resulting in a decrease in the measured elastodynamic nonlinearity.

58 GEOSCIENCES↗
DOE OSTI2024

TRUST Contact Thermal Conductance (TRUST-CTC) Report: FY24

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) project is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are critical to the current and future stockpile. Staff development will include cross-discipline collaboration to provide engineers with experience in both numerical simulations and experimental methods. This work uses and provides feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development. TRUST currently includes five testbeds and their associated engineering analysis baseline models (EABMs): 1. contact thermal conductivity, (CTC) 2. nonlinear dynamics, (ND) 3. sensors in environments for accelerometers, (SEA) 4. sensors in environments for fiber optic displacement gages, and (SEFOD) 5. sensors in environments for thermocouples (SETC). The TRUST project uses single-feature testbeds to quantify uncertainties in specific models and experiments and to identify capability development needs that can help to reduce these uncertainties. Each testbed is designed, configured, and tested in collaboration with groups with design and experimental capability: E-14 and MPA-CINT. The complementary simulations are conducted using W-13 analysis tools and stored in model repositories with plans for incremental progress toward EABM requirements. W-13 extends and exercises the testbed simulations in collaboration with experimentalists for uncertainty quantification of current and future materials, geometries, and environments. Additionally, TRUST is intended to provide engineers in W-13 and E-14 with experience in both numerical simulations and experimental methods through cross-discipline collaborations. Following the introduction to the TRUST project, the remainder of this report focuses on experimental and analytical efforts conducted in Fiscal Year (FY) 2024 relevant to the TRUST Contact Thermal Conductance (CTC) testbed.

42 ENGINEERING↗
DOE OSTI2025

Allosteric prediction via convolutional neural networks and protein structural and dynamical features

Allostery is the phenomenon whereby a binding event or covalent modification at one site in a protein modulates function at a distal site, thus changing a protein’s functional state. As such, it is a ubiquitous aspect of protein functional regulation. Computationally predicting allosteric states is important as part of the broader challenge of functional annotation, but it also has practical implications for drug development, as targeting an allosteric site often affords greater specificity compared with targeting an orthosteric site. This study introduces a machine learning approach to predict the allosteric functional state using the small G-protein KRas as the model system, due to its implication in many types of cancer and being well studied as a result with many x-ray crystallographic structures of KRas available with different mutations and ligands bound. Using structural and dynamical features that can be cast as images, namely interatomic distances, contact maps, covariance, and mutual information, supervised learning was performed using convolutional neural networks. Two pretrained convolutional neural network architectures, GoogLeNet and ResNet18, were fine-tuned to classify KRas into active or inactive states based on these features. Across training regimes, atomic contact maps emerged as the most effective structural feature, whereas linearized mutual information outperformed covariance in capturing dynamical correlations relevant to allostery. Models achieved significant validation accuracy, with atomic contact maps yielding up to 90% accuracy. In conclusion, the findings suggest that integrating global structural rearrangements and correlated motion patterns with deep learning can reliably predict protein allosteric states, offering a promising framework for understanding allosteric regulation and developing targeted therapeutics.

Rajeshwar T., Rajitha [Oak Ridge National Laborato↗
DOE OSTI2026

Molecular Dynamics Investigation of Oil Wetting on Synthetic Polymer Substrates

Understanding the interaction of polymer surfaces with nonpolar, low surface tension liquids, or whether a substrate is oleophobic versus oleophilic, is critical for applications ranging from antifingerprint coatings to oil–water separation membranes and oil spill remediation. Despite its technological importance, the molecular mechanisms underpinning polymer–oil wetting are not well characterized. Here, we employ molecular dynamics simulations to investigate the behavior of n-hexadecane in contact with chemically distinct polymer surfaces, spanning eight constitutional unit chemistries as well as amorphous and crystalline morphologies. This permits a critical examination of both thermodynamic and dynamic descriptors of oleophobicity, including oil contact angle, dewetting free energy, interfacial diffusivity, and a proposed “ghost probe energy,” which does not require explicit simulation of oil–polymer interactions. We find that the oil contact angle does not reliably distinguish oleophobic behavior across polymer chemistries, whereas other metrics provide clearer and more consistent differentiation. Analysis of the results reveals that polymer–oil wetting behavior is primarily governed by interfacial van der Waals interactions and modulated by surface flexibility and morphology. Collectively, this work establishes a computational framework for characterizing oil wetting and provides additional insight into what molecular-level factors dictate trends in oleophobicity.

lipids↗
DOE OSTI2025

The molten salt tritium transport experiment: A pumped fluoride salt loop for hydrogen isotope experimentation

Molten salt reactors (MSRs) and fusion reactors propose to use molten salts as coolants and breeder blanket materials, respectively. Tritium, however, poses safety concerns in both reactor types due to its ability to permeate through reactor materials and potential for environmental release. This manuscript addresses the tritium transport phenomena in molten salts and presents the design and analysis of the Molten Salt Tritium Transport Experiment (MSTTE). MSTTE is a forced-convection fluoride salt loop intended to measure hydrogen isotope permeation through structural materials in a flowing salt system. In the first phase, MSTTE will use FLiNaK salt and deuterium as surrogates for FLiBe and tritium, with future plans to utilize tritium and FLiBe. MSTTE couples a Copenhagen Atomics pumped salt loop with an external test section that introduces hydrogen isotopes into the loop and measures transport phenomena. The Hydrogen Injection System (HIS) controls hydrogen isotope introduction into the molten salt loop. Here, the permeation test section measures the permeation rate through stainless steel tubing in contact with flowing salt. Computational fluid dynamics (CFD) analysis ensures fully developed salt flow in the permeation test section. MSTTE is modeled with MELCOR-TMAP to predict the permeation rate as a function of experimental variables such as source term, salt flow rate, and salt temperature. Results indicate that the source term is the only parameter with a significant effect on the permeation rate. Pressure drop analysis suggests that the loop should operate below 200 LPM to maintain a pressure drop below 200 kPa. Additionally, finite-element analysis assesses thermal stress during loop operation to ensure the experiment's safe design. MSTTE will provide semi-integral data on tritium transport phenomena in molten salts and serve as a testbed for advancing molten salt technology.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Adaptively remeshed multiphysical modeling of resistance forge welding with experimental validation of residual stress fields and measurement processes

Welding processes used in the production of pressure vessels impart residual stresses in the manufactured component. Computational modeling is critical to predicting these residual stress fields and understanding how they interact with notches and flaws to impact pressure vessel durability. Here, in this work, we present a finite element model for a resistance forge weld and validate it using laboratory measurements. Extensive microstructural changes, near-melt temperatures, and large localized deformations along the weld interface pose significant challenges to Lagrangian finite element modeling. The proposed modeling approach overcomes these roadblocks in order to provide a high-fidelity simulation that can predict the residual stress state in the manufactured pressure vessel; a rich microstructural constitutive model accounts for material recrystallization dynamics, a frictional-to-tied contact model is coordinated with the constitutive model to represent interfacial bonding, and adaptive remeshing is employed to alleviate severe mesh distortion. An interrupted-weld approach is applied to the simulation to facilitate comparison to displacement measures. Several techniques are employed for residual stress measurement in order to validate the finite element model: neutron diffraction, the contour method, and the slitting method. Model-measurement comparisons are supplemented with detailed simulations that reflect the configurations of the residual-stress measurement processes themselves. The model results show general agreement with experimental measurements, and we observe some similarities in the features around the weld region. Factors that contribute to model-measurement differences are identified. Finally, we conclude with some discussion of the model development and residual stress measurement strategies, including how to best leverage the efforts put forth here for other weld problems.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Dynamically tunable membrane metasurfaces for infrared spectroscopy and strong light-matter interactions

Mid-infrared spectroscopy enables biochemical sensing by identifying vibrational molecular fingerprints, but it faces limitations in instrumentation portability and analytical sensitivity. Optical metasurfaces with strong mid-infrared photonic resonances provide an attractive solution towards on-chip spectrometry and sensitive molecular detection, yet their static nature hinders their anticipated impact. Here, we introduce and demonstrate dynamically tunable silicon membrane metasurfaces exhibiting high-Q transmissive resonances in the fingerprint region. By harnessing silicon’s thermo-optical properties, we achieve continuous modulation of coupling-induced transparency (CIT) modes that emerge upon the interference of quasi-bound states in the continuum (q-BICs) and surface lattice modes (SLMs). We measure a spectral tuning rate of 0.06 cm −1 K −1 by continuously sweeping the sharp CIT resonances over a 23.5 cm −1 spectral range across a temperature range of 300–700 K. In the current proof‑of‑concept implementation, the dynamic transmission control enables non-contact chemical analysis of polymer films by detecting characteristic absorption bands of polystyrene (1450 and 1492 cm −1 ) and poly(methyl methacrylate) (1730 cm −1 ) without requiring conventional spectrometers. When analyte molecules fill the metasurface-generated photonic cavities, we demonstrate vibrational strong coupling between the poly(methyl methacrylate)’s carbonyl band and the CIT mode, manifested in a Rabi splitting of ~43 cm −1 . Our results establish a new photonic platform that unites spectral precision, strong field enhancement, and reconfigurability, offering diverse potential for compact mid-infrared spectroscopy, molecular sensing, and programmable polaritonic photonics.

74 ATOMIC AND MOLECULAR PHYSICS↗