Search NASA⌕ Search

SEARCH · Search NASA

Results for “EBSD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Investigation of the effect of structural defects from hydride precipitation on superconducting properties of high purity SRF cavity Nb using magneto-optical and electron imaging methods

Abstract Nb is an elemental superconductor with a critical temperature of 9.3 K and is widely used to fabricate superconducting radiofrequency (SRF) cavities for particle accelerators. However, microstructural defects in Nb, such as grain boundaries (GBs) and dislocations, can act as pinning centers for magnetic flux that can degrade SRF cavity performance. Hydrogen contamination is also detrimental to SRF cavity performance due to the formation of normal conducting hydrides during cool down. In this study, disc shaped Nb bi-crystals extracted from high-purity large-grain Nb slices were investigated to study the effects of GBs, hydrogen, and dislocations on superconducting properties. Grain orientation and GB misorientation were measured using Laue x-ray diffraction and electron backscattered diffraction (EBSD) analyses. Cryogenic magneto-optical imaging was used to directly observe magnetic flux penetration below T c = 9.3 K. Damage caused by low temperature precipitation of hydrides and their dissolution upon reheating after cryogenic cycles was examined using electron channeling contrast imaging, and EBSD. The relationships between hydride formation, dislocation content, GBs, cryo-cooling, heat treatment (HT), and flux penetration indicate that both GB character and hydrogen content affect magnetic flux penetration. Such flux penetration could be facilitated by dislocation structures and low angle GBs resulting from hydride precipitation and HT.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Process-dependent anisotropic thermal conductivity of laser powder bed fusion AlSi10Mg: impact of microstructure and aluminum-silicon interfaces

Purpose AlSi10Mg alloy is commonly used in laser powder bed fusion due to its printability, relatively high thermal conductivity, low density and good mechanical properties. However, the thermal conductivity of as-built materials as a function of processing (energy density, laser power, laser scanning speed, support structure) and build orientation, are not well explored in the literature. This study aims to elucidate the relationship between processing, microstructure, and thermal conductivity. Design/methodology/approach The thermal conductivity of laser powder bed fusion (L-PBF) AlSi10Mg samples are investigated by the flash diffusivity and frequency domain thermoreflectance (FDTR) techniques. Thermal conductivities are linked to the microstructure of L-PBF AlSi10Mg, which changes with processing conditions. The through-plane exceeded the in-plane thermal conductivity for all energy densities. A co-located thermal conductivity map by frequency domain thermoreflectance (FDTR) and crystallographic grain orientation map by electron backscattered diffraction (EBSD) was used to investigate the effect of microstructure on thermal conductivity. Findings The highest through-plane thermal conductivity (136 ± 2 W/m-K) was achieved at 59 J/mm 3 and exceeded the values reported previously. The in-plane thermal conductivity peaked at 117 ± 2 W/m-K at 50 J/mm 3 . The trend of thermal conductivity reducing with energy density at similar porosity was primarily due to the reduced grain size producing more Al-Si interfaces that pose thermal resistance. At these interfaces, thermal energy must convert from electrons in the aluminum to phonons in the silicon. The co-located thermal conductivity and crystallographic grain orientation maps confirmed that larger colonies of columnar grains have higher thermal conductivity compared to smaller columnar grains. Practical implications The thermal properties of AlSi10Mg are crucial to heat transfer applications including additively manufactured heatsinks, cold plates, vapor chambers, heat pipes, enclosures and heat exchangers. Additionally, thermal-based nondestructive testing methods require these properties for applications such as defect detection and simulation of L-PBF processes. Industrial standards for L-PBF processes and components can use the data for thermal applications. Originality/value To the best of the authors’ knowledge, this paper is the first to make coupled thermal conductivity maps that were matched to microstructure for L-PBF AlSi10Mg aluminum alloy. This was achieved by a unique in-house thermal conductivity mapping setup and relating the data to local SEM EBSD maps. This provides the first conclusive proof that larger grain sizes can achieve higher thermal conductivity for this processing method and material system. This study also shows that control of the solidification can result in higher thermal conductivity. It was also the first to find that the build substrate (with or without support) has a large effect on thermal conductivity.

Engineering↗
DOE OSTI2026

Tailoring Thermal and Mechanical Performance Through Multimaterial Laser Powder Directed Energy Deposition of Copper and 17-4PH Stainless Steel

This study investigates the additive manufacturing (AM) processing, microstructural evolution, and resulting mechanical and thermal properties of multimaterial components combining 17-4PH stainless steel and pure copper (Cu) fabricated via laser powder directed energy deposition (LP-DED). Conventional tooling steels exhibit limited thermal conductivity, significantly constraining production throughput in high-volume processes. Incorporating Cu, with its superior thermal conductivity, could significantly enhance tool performance, though Cu and steel present metallurgical incompatibilities when processed via AM. A systematic investigation was conducted across compositions ranging from 0 to 100 wt% Cu, revealing critical thresholds influencing solidification behavior, defect formation, microstructure, hardness, and thermal transport. Optical microscopy, electron backscatter diffraction (EBSD), hardness testing, and thermal conductivity measurements provided comprehensive process–structure–property correlations. Severe hot cracking occurred at low-Cu contents (6–25 wt%), aligning generally well with crack susceptibility modeling, with an unexpected discrepancy at 25 wt%. Porosity remained low (≥99% dense) throughout the compositional spectrum. EBSD analysis revealed a transformation from columnar martensitic structures at low-Cu contents to equiaxed FCC Cu-dominated structures at higher Cu concentrations, highlighting the complex microstructural transitions driven by Cu-induced changes in solidification and phase stability. Hardness decreased from 330 HV (pure 17-4PH) to 62 HV (pure Cu), consistent with microstructural changes. Concurrently, thermal conductivity improved substantially from 13.5 W/m K to 367.9 W/m K, emphasizing Cu’s dominant role in thermal transport. The findings highlight the feasibility of leveraging compositional gradients between 17-4PH and Cu to achieve tailored tooling with optimized thermal and mechanical performance.

17-4PH↗
DOE OSTI2021

Hot rolling of ZK60 magnesium sheet with isotropic tensile properties from tubing made by Shear Assisted Processing and Extrusion (ShAPE)

In order to evaluate the viability of ShAPE processed Mg alloys as a feedstock for fabricating lightweight sheet material, tubes consisting of ShAPE-extruded Mg alloy ZK60 were flattened into plates and hot rolled at 450 °C to reductions of 37%, 68%, and 93%. The mechanical properties and microstructure of the rolled material were characterized through tensile testing and electron backscattered diffraction (EBSD). ZK60 specimens rolled to 68% reduction had tensile properties similar to published properties of rolled ZK60 sheets fabricated using conventional processes, and exhibited negligible tensile anisotropy referenced to the rolling direction. Additional rolling from 68% to 93% reduced the ultimate tensile stress in the rolling direction from 341.74±5.96 MPa to 260.76±22.4MPa. The yield stress and elongation to failure of the material also decreased from 292.16±1.11 MPa to 256.93±18.4 MPa and 6.95±1.94% to 3.38±0.51%, respectively, but negligible little anisotropy was observed with respect to loading direction. EBSD mapping indicated that the as-extruded ZK60 had texture rotated away from the basal direction which developed into a strong basal texture over numerous hot rolling steps. This evolution in texture has been observed after rolling for hot-rolled ZK60 fabricated through conventional extrusion processes. The initial grain structure was found to have experienced noticeable twinning from flattening the tube into plate. After hot rolling, the grain structure became more equiaxed, but the average grain diameter did not change appreciably from 5.15 ± 3.39 µm in the ShAPE extruded material, to 5.27 ± 12.44 µm in the 93% hot rolled sheet. This response to hot rolling is similar to the response of ZK60 fabricated using other methods such as Equal Channel Angular Processing (ECAP). Therefore, this work demonstrates ShAPE has the potential as an alternative method to producing feedstock for Mg alloy sheets. Modifications to the experimental procedure which could lead to improvements in observed properties are briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

How Austenitic Is a Martensitic Steel Produced by Laser Powder Bed Fusion? A Cautionary Tale

Accurate phase fraction analysis is an essential element of the microstructural characterization of alloys and often serves as a basis to quantify effects such as heat treatment or mechanical deformation. Additive manufacturing (AM) of metals, due to the intrinsic nonequilibrium solidification and spatial variability, creates additional challenges for the proper quantification of phase fraction. Such challenges are exacerbated when the alloy itself is prone to deformation-induced phase transformation. Using commonly available in-house X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) and less commonly used synchrotron-based high-energy X-ray diffraction, we characterized nitrogen-atomized 17-4 precipitation-hardening martensitic stainless steel, a class of AM alloy that has received broad attention within the AM research community. On the same build, our measurements recovered the entire range of reported values on the austenite phase fractions of as-built AM 17-4 in literature, from ≈100% martensite to ≈100% austenite. Aided by Calphad simulation, our experimental findings established that our as-built AM 17-4 is almost fully austenitic and that in-house XRD and EBSD measurements are subject to significant uncertainties created by the specimen’s surface finish. Hence, measurements made using these techniques must be understood in their correct context. Our results carry significant implications, not only to AM 17-4 but also to AM alloys that are susceptible to deformation-induced structure transformation and suggest that characterizations with less accessible but bulk sensitive techniques such as synchrotron-based high energy X-ray diffraction or neutron diffraction may be required for proper understanding of these materials.

17-4 steel↗
DOE OSTI2024

Focused Ion Beam Tomography of Alloy 617 Corroded in Molten Chloride Salt

Materials qualification of reactor structural materials is a critical step in rapid implementation of advanced nuclear reactor technologies, particularly to assess the corrosion performance in these designs. Accelerated qualification of reactor structural materials requires incorporating powerful computational toolsets, such as phase field modelling in the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework, to predict the evolution of structural materials due to corrosion. Accordingly, computational toolsets will require experimental data generated at appropriate length scales to validate accuracy. Focused ion beam (FIB) provides a high degree of control over manipulation of materials for analytical purposes, including capturing data on the evolution in the microstructure and elemental composition of materials at the mesoscale, an appropriate length scale for phase field modelling of intergranular diffusion phenomena using the MOOSE framework. For instance, the FEI Helios G4 UX dual beam plasma FIB microscope at the Irradiated Materials Characterization Laboratory (IMCL) is capable of backscatter diffraction (EBSD) and energy-dispersive x-ray spectroscopy (EDS) documenting the evolution in the microstructure and elemental composition, respectively. The Helios can perform EDS and EBSD three-dimensionally (3D) using tomography, which is then combined using different software packages to visualize 3D volumes correlating elemental composition to microstructural data. The purpose of this investigation was to develop a streamlined characterization and data processing workflow for 3D tomography studies on the FEI Helios G4 plasma FIB. The investigation is segmented into three parts: 1) Optimizing the data collection workflow, 2) identifying appropriate data processing and visualization software (i.e. DREAM.3D, MIPAR, and VGStudioMax), and 3) establishing an infrastructure for public release. The optimization of the data collection workflow is in collaboration with members of the U220 department to setup formal training on the tomography operation of the G4, through ThermoFisher Scientific, and exploring DREAM.3D, MIPAR, and VGStudioMax data processing/visualization software packages. VGStudioMax currently demonstrates the most promise for future use. Optimization of the data collection and processing workflow is still ongoing. A collaboration with INL High Performance Computing (HPC) established an open-source license for expediting the public release of FIB tomography datasets through HPC. FIB tomography data generated by the G4 will provide comprehensive data for validating 3D phase field mesoscale modelling tools within the MOOSE framework for accelerated qualification of reactor structural materials.

Copeland-Johnson, Trishelle↗
DOE OSTI2023

Calcite Twinning in Mollusk Shells and Carrara Marble

Mollusk shells protect the animals that form and inhabit them. They are composites of minerals and organics, with diverse mesostructures, including nacre, prismatic calcite, crossed-lamellar aragonite, and foliated calcite. Twins, that is, crystals mirror symmetric with respect to their coherent interface, occurring as formation or deformation twins, are observed in all mollusk shell mesostructures but never within calcite prisms. Here, nanotwins and microwins within single calcite prisms are observed in different shells. Using Polarization-dependent Imaging Contrast (PIC) mapping with 20–60 nm resolution, twins are observed to be 0.2–3 µm thick layers of differently oriented and colored crystals with respect to the main prism crystal. Multiple twins are interspersed with the prism crystal, parallel to one another, and similarly oriented. When comparing images of calcite prisms and twins obtained by PIC mapping and by Electron Back-Scattered Diffraction (EBSD), the images correspond precisely. All twins are e-twin types, with 127° angular distance between c-axes. E-twins are the most common deformation twins in geologic calcite, as also observed here in Carrara marble. Location of all twins near the outer surface of all shells and e-twin type both suggest that twins within calcite prisms in mollusk shells result from deformation twinning.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Quantitative study of the effect of grain boundary parameters on the slip system level Hall-Petch slope for basal slip system in Mg-4Al

Several theoretical studies have reported that the geometry and structure of grain boundaries in polycrystalline materials could impose a significant effect on the Hall-Petch slope. However, experimental observations are primarily limited by the ability of the techniques to accurately quantify the grain boundary strength and validate these theoretical models. Using high-resolution electron backscatter diffraction (HR-EBSD), the local stress tensor ahead of a slip band blocked by a grain boundary was quantified and coupled with a continuum dislocation pile-up model to assess the barrier strength of specific grain boundaries to specific slip systems, referred to as micro-Hall-Petch coefficient. For basal slip system in a deformed Mg-4Al alloy, the micro-Hall-Petch coefficient ($k^{basal}_{μ}$) varied significantly, from 0.054 to 0.184 MPa - m 1/2 for nine different grain boundaries. These results were correlated with geometric descriptors of the respective grain boundaries, with three-dimensional GB profile additionally measured via focused ion beam milling. It was found that the angle between the two slip plane traces on the grain boundary plane was the most sensitive parameter affecting $k^{basal}_{μ}$, followed by the angle between the slip directions. A functional form for calculation of $k^{basal}_{μ}$ depending on these two angles is proposed to augment crystal plasticity constitutive models with slip resistance dependent on some measure of the grain size. The method allows a new pathway to calibrate grain size strengthening parameters in crystal plasticity models, allowing further computational investigations of the interrelationship between texture, grain morphology, and the Hall Petch effect.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Estimation of micro-Hall-Petch coefficients for prismatic slip system in Mg-4Al as a function of grain boundary parameters

Grain size strengthening, referred to as the Hall-Petch effect, is a common strategy to improve the yield strength of magnesium (Mg) alloys. Several experimental studies have reported that the Hall-Petch slope strongly depends on the texture of the alloy. This effect arises from altering grain boundaries (GBs) resistance to different slip systems to transfer across adjacent grains. The grain boundary barrier strength of certain grain boundaries to basal slip, referred to as basal micro-Hall-Petch, was investigated in the previous work. Here in this study, the micro-Hall-Petch coefficient values for the prismatic slip $(k^{prismatic}_{μ})$ in Mg-4Al and their correlation with the grain boundary parameters were investigated. An experimental method was developed to initiate the prismatic slip band at low-stress levels. High-resolution electron backscatter diffraction (HR-EBSD) was used to measure the residual stress tensor, from which the resolved shear stress ahead of blocked prismatic slip bands was computed for seven different grain boundaries. $(k^{prismatic}_{μ})$ values for each individual GB were calculated by coupling the stress profile information with a continuum dislocation pile-up model. The $(k^{prismatic}_{μ})$ values vary from 0.138 MPa.m 1/2 to 0.685 MPa. m 1/2 which are almost three times larger than the calculated values for the basal micro-Hall-Petch. The $(k^{prismatic}_{μ})$ values were correlated with the GB parameters, and a functional relationship depending on the two most effective angles, the angle between the traces of the slip planes on the GB plane ($\phi$) and the angle between incoming and outgoing slip directions (κ), was proposed to estimate the Hall-Petch barrier for prismatic slip system. The work provides coefficients that can be supplied as input to crystal plasticity models to couple the effect of texture and grain size effectively.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Process-Structure-Property Relations for As-Deposited Solid-State Additively Manufactured High-Strength Aluminum Alloy

Solid-state additive manufacturing methods provide innovative solutions to circumvent problems associated with materials susceptible to hot cracking by avoiding liquid solid phase transformations. In this work, the process parameter influence on microstructural evolution and mechanical response of a fully dense aluminum alloy 7050 (AA7050) component manufactured via a rapid, solid-state additive manufacturing process known as Additive Friction Stir Deposition (AFS-D) was quantified for the first time. Three sections (starting dwell, transient, crossover of roads) of the deposition that exhibit differing thermomechanical processing histories were evaluated for the resulting microstructure and mechanical response. The microstructural characterization was performed on the as-deposited AA7050 via Electron Backscatter Diffraction (EBSD), TEM, optical microscopy, and Scanning Electron Microscopy (SEM). The microstructural characterization revealed refined constituent particles and grains throughout the as-deposited AA7050 microstructure. Furthermore, quasi-static tensile experiments were conducted in both the build and transverse directions, in order to quantify the orientation influence on tensile properties of the as-deposited AA7050 build. Spatially dependent tensile properties were observed in the material due to heat input variation coarsening of secondary phases towards the initial layers of the AFS-D build. Post-mortem analysis revealed that voids nucleated and coalesced from the overgrowth of the strengthening precipitates present in the material, resulting in fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the correlation between plastic strain and misorientation in polycrystalline body-centered-cubic microstructures with an emphasis on the grain size, loading history, and crystallographic orientation

In this work, the correlation between plastic strain and crystallographic misorientation, grain size, grain orientation, distance from grain boundary, and loading history were investigated experimentally and numerically for body-centered-cubic (BCC) polycrystalline microstructures based on a misorientation deviation (MD) approach. Nine monotonic tensile experiments were performed on two BCC titanium alloys inside a scanning electron microscope (SEM). The influence of reference orientation was explored both at the grain scale and at the mesoscale using electron backscattered diffraction (EBSD). The correlation between global plastic strain and the MD was quantified. The tendency for orientation change was quantified as a function of plastic strain and grain orientation for three crystallographic orientations (i.e., [100], [110], and [111]) with respect to tensile direction. The subpopulation of small grains exhibited a lower level of misorientation dispersion compared with larger grains, and this discrepancy became more pronounced at higher strains. An empirical equation was proposed to estimate the level of misorientation dispersion for individual grains as a function of grain size and global plastic strain level. Two interrupted in-situ SEM experiments were performed, and this resulted in a significantly increased misorientation compared with uninterrupted tests performed to similar plastic strain levels.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Stoichiometric effects on grain growth in zirconium carbide coatings for high-temperature nuclear fuel

Interest in coated particle fuel for space nuclear propulsion (SNP) has expanded in recent years due to successful demonstrations of the resiliency of the coatings to extreme environments. For SNP applications, the coating layer for the particle design needs to be able to withstand exposure to high temperature hydrogen during operating conditions. ZrC has been proposed as a protective layer, however, it is important to understand the high temperature behavior to ensure adequate protection to this fuel. In this study, surrogate ZrC coated particles were heat treated at 1900 °C up to 300 min, to examine how the microstructure evolves when exposed to high temperature. Scanning electron microscopy and electron backscatter diffraction (EBSD) were conducted to determine grain size and grain boundary character and orientation to determine the degree of change in the ZrC layer post heat treatment. Raman spectroscopy provided insight to understand how the as-fabricated stoichiometry of each sample contributed to the differences in grain growth behavior. Despite the as-fabricated samples showing a similar initial grain size and grain boundary character, the samples with a higher amount of excess carbon exhibited smaller grain areas and slower growth rates when exposed to 1900 °C. In conclusion, this investigation details the as-fabricated microstructure of the ZrC layer, specifically grain size, evolved under high temperature as this can impact the performance of the fuel under operating conditions.

EBSD↗
DOE OSTI2020

Integrated three-dimensional characterization of reactive phase formation and coarsening during isothermal annealing of metastable Zn–3Mg–4Al eutectic

Microstructural instabilities associated with a metastable lamellar eutectic when exposed to an elevated temperature were analyzed in a Zn-3Mg-4Al alloy as a model system. X-ray diffraction and scanning electron microscopy showed that annealing at a temperature 43 K below the equilibrium eutectic temperature converted the metastable ternary MgZn 2 /η-Zn/β-ZnAl eutectic to a stable mixture of Mg 2 Zn 11 /η-Zn/α-Al. 3D EBSD suggested that supersaturation of η-Zn with Mg and Al eased difficulties in nucleation of Mg 2 Zn 11 and α-Al at the MgZn 2 /η-Zn phase interfaces. Quasi-in-situ X-ray nanotomography revealed that a reactive diffusion process prevailed in an early stage of annealing leading to rapid consumption of MgZn 2 for growth of Mg 2 Zn 11 and concomitant thinning and pinch-off of η-Zn lamellae. The reactive diffusion process also brought about significant and quantifiable changes in the topological characteristics of the η-Zn phase at remarkably shorter time scales compared to Rayleigh instability and Ostwald ripening mechanisms. Overall, the present results provide fresh insights on the short-term annealing effects on metastable eutectics, with relevance to structural evolution in additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

An automated procedure built on MTEX for reconstructing deformation twin hierarchies from electron backscattered diffraction datasets of heavily twinned microstructures

Here we present a set of algorithms built on the MTEX and MATLAB graph toolboxes for automatic reconstruction of deformation twin hierarchies from Electron Backscatter Diffraction (EBSD) datasets with a focus on developing methods for heavily twinned microstructures (twin fractions >0.5). The algorithms address key issues arising at large strains, mainly: missing twin relationships, grouping of heavily deformed grain fragments into families of similar orientation originating from a single initial grain, identification of parent fragments for large twin volume fractions, and classification of families having twin relationships with multiple families. To facilitate the development of these algorithms, large-grained ultra-high purity α-Ti deformed in compression along two directions is investigated. Graphs are utilized to handle non-local geometric merging and to represent relationships throughout the reconstruction process. When determining if a grain fragment is from the undeformed microstructure, the combined metrics of the fragment's orientation volume fraction in the initial texture and the directed graph centrality measure of out-closeness (the number of nodes reached in a graph from a given node) are essential. To address automation in reconstructing the sequence of twinning and relating fragments originating from a single grain in the initial microstructure, the twin family tree is formulated as a minimum spanning tree emanating from the initial grain family. A scheme constructing the distances associated with twin relationship comprising the spanning tree is developed, and a novel quasi-directional Prim spanning tree algorithm is used to determine the twin family tree. The procedure is demonstrated to significantly improve the level of automation in reconstructing twin hierarchies in heavily twinned microstructure compared to other methodologies in literature. The procedure can readily be applied to analyses of twinning in metals, as well as provide an approach for routinely extracting twin statistics at larger deformation levels than previously possible. Significantly, the procedure is demonstrated to be capable of identifying third generation twinning in α-Ti microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Correlating dislocation structures to basal and prismatic slip bands near grain boundaries in tensile-tested Mg–4Al using a multiscale electron microscopy approach

Dislocation structures where basal and prismatic slip bands meet grain boundaries in tensile-tested Mg with 4 wt% Al (Mg–4Al) were studied using a multiscale electron microscopy approach to explore the assumptions made for the dislocation pileup theory: a) slip bands consist of dislocation arrays piling up near grain boundaries, and b) stress concentration in the adjacent grain is solely caused by dislocation pileup. After post-testing electron backscatter diffraction (EBSD) scans, focused-ion-beam (FIB) lift-out specimens were prepared from regions of interest so that the specimen plane is parallel to the bulk sample surface to allow for direct correlation between mesoscale and microscale characterization. High dislocation density and the dislocation arrays in the slip bands corroborated with the first assumption. Evidence of plastic deformation in all grains, however, showed that the second assumption was false. Additionally, dislocation structures including crystal rotation boundaries and dislocations dissociating to the basal plane provide additional stress relief mechanisms near grain boundaries that are not accounted for in many crystal plasticity models, which requires auxiliary models to more accurately predict the stress and strain distribution in a microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spall damage mechanisms in laser powder bed fabricated stainless steel 316L

This paper reports on spall damage mechanisms in laser powder bed fusion (LPBF) fabricated stainless steel 316L (SS316L) subjected to uniaxial, strain plate-impact loading and explores failure evolution with increasing impact velocity and peak pressure. Analysis of velocimetry profiles reveals a heterogeneous failure response with several different failure mechanisms activated during impact and resulting spall. The analysis is supported by optical microscopy and electron backscattered diffraction (EBSD) observation of soft recovered impacted samples, which show evidence of localized nano-twinning, twin growth, severe grain rotation, and grain refinement along the spall plane, in addition to pore nucleation, coalescence, and growth. Furthermore, the observed failure mechanisms, including crack formation and propagation along high angle grain boundaries (HAGBs), are not consistently indicative of ductile fracture typical of wrought stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Interplay of strain and phase evolution of laser powder bed fusion Ti–6Al–4V

While additive manufacturing (AM) provides a method of producing geometrically complex and highly detailed structures, the generation of residual strain in AM processes like laser powder bed fusion (L-PBF) can negatively impact performance-enabling properties. In applications such as orthopedic implants, specific performance windows require optimized microstructures in order to obtain desirable properties from multi-phase alloys like Ti–6Al–4V. This research aims to quantify the microscale origins of strain in L-PBF manufactured Ti–6Al–4V by understanding how strain is distributed at the grain and sub-grain scale, the interplay between phase evolution and strain, and examining post-processing strain relief strategies to control these features. Model spinal cage implants were manufactured from Ti–6Al–4V powder via L-PBF and then subjected to strain relieving heat treatment cycles above and below the Ti–6Al–4V β transus as a function of time and cooling rate. Residual strain was then studied via high resolution electron backscatter diffraction (HR-EBSD), and 2D strain maps with sub-micron resolution were generated for each post-processing state. It was found that macroscale thermal strains decreased with heat treatment time, but additional contributions from phase stabilizing residual strains retained primarily in the α' grains as lattice distortive strain remained. Additionally, the retention of β phase significantly changed the strain and dislocation distribution while reducing overall residual strain. In conclusion, these results were validated and reinforced with 3D mesoscopic micromechanical modeling of strain behavior across simulated microstructures, confirming that the local lattice dilation of α’ martensite is a primary contributor of microscale strain generation and retention in L-PBF Ti–6Al–4V.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Analysis of orientation-dependent deformation mechanisms in additively manufactured Zr using in-situ micromechanical testing: Twinning and orientation gradient

Here, orientation-dependent plasticity in zirconium (Zr)-alloy, which is produced through ultrasonic additive manufacturing (UAM) with subsequent hot-isostatic pressing (HIP), was analyzed by recording electron backscattered diffraction (EBSD) data during in-situ micromechanical testing. Three (0001) plane orientations of a hexagonal close-packed (HCP) structure were analyzed parallel to (1) the rolling direction [X||tensile direction (TD)], (2) the build direction [Z], and (3) the transverse direction [Y]. The analysis revealed that the grains with ~<0001>||TD show twin-dominant plasticity with three variants from {10 $\overline{1}$ 2}<$\overline{1}$ 011>; minor slipping with ($10\overline{1}$ 1)[$\overline{2}$ 113], and ($11\overline{2}$ 2)[$\overline{1} \overline{1}$ 23] pyramidal slip has also been observed. However, grains with orientation ~<0001>⊥TD are mainly sensitive to dislocations assisted plasticity-leading to orientation gradients formation. Furthermore, the neck formation was identified as originating from higher populated micro-crack locations and their association with localized plasticity at defect points in the UAM material. These results demonstrate that minimization of impurities to enable grain growth across prior foil interfaces makes HIP an effective methodology for producing Zr plate, with deformation characteristics expected for conventionally manufactured Zr.

36 MATERIALS SCIENCE↗