Search NASA⌕ Search

SEARCH · Search NASA

Results for “EXHAUST NOZZLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Effects of nozzle exit geometry and pressure ratio on plume shape for nozzles exhausting into quiescent air

The effects of varying the exit geometry on the plume shapes of supersonic nozzles exhausting into quiescent air at several exit-to-ambient pressure ratios are given. Four nozzles having circular throat sections and circular, elliptical and oval exit cross sections were tested and the exit plume shapes are compared at the same exit-to-ambient pressure ratios. The resulting mass flows were calculated and are also presented.

Scallion, William I.↗
NASA NTRS2010

Multiple Exhaust Nozzle Effects on J-2X Gas Generator Outlet Impedance

The current test setup of the J-2X gas generator system uses a multiple nozzle configuration to exhaust hot gases to drive the propellant supply turbines. Combustion stability assessment of this gas generator design requires knowledge of the impedance effects the multiple nozzle configuration creates on the combustion chamber acoustic modes. Parallel work between NASA and Sierra Engineering is presented, showing two methods used to calculate the effective end impedance resulting from multiple nozzle configurations. The NASA method is a simple estimate of the effective impedance using the long wavelength approximation. Sierra Engineering has developed a more robust numerical integration method implemented in ROCCID to accommodate for multiple nozzles. Analysis using both methods are compared to J-2X gas generator test data collected over the past year.

Kenny, R. Jeremy↗
NASA NTRS1999

Static Performance of a Fixed-Geometry Exhaust Nozzle Incorporating Porous Cavities for Shock-Boundary Layer Interaction Control

An investigation was conducted in the model preparation area of the Langley 16-Foot Transonic Tunnel to determine the internal performance of a fixed-geometry exhaust nozzle incorporating porous cavities for shock-boundary layer interaction control. Testing was conducted at static conditions using a sub-scale nozzle model with one baseline and 27 porous configurations. For the porous configurations, the effects of percent open porosity, hole diameter, and cavity depth were determined. All tests were conducted with no external flow at nozzle pressure ratios from 1.25 to approximately 9.50. Results indicate that baseline nozzle performance was dominated by unstable, shock-induced, boundary-layer separation at over-expanded conditions. Porous configurations were capable of controlling off-design separation in the nozzle by either alleviating separation or encouraging stable separation of the exhaust flow. The ability of the porous nozzle concept to alternately alleviate separation or encourage stable separation of exhaust flow through shock-boundary layer interaction control offers tremendous off-design performance benefits for fixed-geometry nozzle installations. In addition, the ability to encourage separation on one divergent flap while alleviating it on the other makes it possible to generate thrust vectoring using a fixed-geometry nozzle.

Asbury, Scott C.↗
NASA NTRS1997

Development of a Telescoping Vaned Exhaust Nozzle for the ASTOVL LiftFan(Trademark) Application

A discussion on the development of a Telescoping, Vaned, Exhaust Nozzle (TEVEN) is presented. This nozzle was challenged to meet the thrust vectoring requirements of an Advanced Short Takeoff and Vertical Landing (ASTOVL) aircraft. The nozzle underwent a development process from concepts to detail design using computational flow analyses and from subscale performance verification tests to full-scale hardware design. The LiftFan(Trademark) nozzle is capable of providing a pitch vector range of about 80 degrees from up to 20 degrees forward to 60 degrees aft. In addition, a set of post exit yaw doors provide +/- 10 degrees yaw while maintaining a relatively high performance at all operating conditions. Further, the nozzle is axially compact, to be stowable in very short length (LJD less than 0.3), while efficiently converging the upstream nozzle flow from an annular cross section to a "D" shape at the nozzle exit. The discussion includes a review of various nozzle concepts, viscous flow analyses, and results from 1/3 scale nozzle model tests conducted at NASA LeRC Powered Lift Facility (PLF) in 1994.

Sokhey, Jack S.↗
NASA NTRS1950

Altitude Performance Characteristics of Turbojet-engine Tail-pipe Burner with Variable-area Exhaust Nozzle Using Several Fuel Systems and Flame Holders

A tail-pipe burner with a variable-area exhaust nozzle was investigated. From five configurations a fuel-distribution system and a flame holder were selected. The best configuration was investigated over a range of altitudes and flight Mach numbers. For the best configuration, an increase in altitude lowered the augmented thrust ratio, exhaust-gas total temperature, and tail-pipe combustion efficiency, and raised the specific fuel consumption. An increase in flight Mach number raised the augmented thrust ratio but had no apparent effect on exhaust-gas total temperature, tail-pipe combustion efficiency, or specific fuel consumption.

ENGINES, TURBOJET↗
NASA NTRS1979

Effect of shocks on film cooling of a full scale turbojet exhaust nozzle having an external expansion surface

Cooling is one of the critical technologies for efficient design of exhaust nozzles, especially for the developing technology of nonaxisymmetric (2D) nozzles for future aircraft applications. Several promising 2D nozzle designs have external expansion surfaces which need to be cooled. Engine data are scarce, however, on nozzle cooling effectiveness in the supersonic flow environment (with shocks) that exists along external expansion surfaces. This paper will present experimental film cooling data obtained during exploratory testing with an axisymmetric plug nozzle having external expansion and installed on an afterburning turbojet engine in an altitude test facility. The data obtained shows that the shocks and local hot gas stream conditions have a marked effect on film cooling effectiveness. An existing film cooling correlation is adequate at some operating conditions but inadequate at other conditions such as in separated flow regions resulting from shock-boundary-layer interactions.

Straight, D. M.↗
NASA NTRS1956

Effect of Several Design Variables on Internal Performance of Convergent-plug Exhaust Nozzles

Numerous experiments were conducted to determine factors which affect the internal performance of convergent-plug exhaust nozzles. The results of these experiments, which include effects of such things as plug shape, nozzle inlet Mach number, and outer-shell characteristics, provide a basis for optimum desifn from the standpoint of weight and size. The results also show performance penalties which can result when the nozzle is too small.

Krull, H George↗
NASA NTRS1986

Dynamic loads on twin jet exhaust nozzles due to shock noise

Acoustic near field data were collected with model single and twin jet nozzles to determine if closely spaced nozzles produce higher acoustic loading than do single nozzles. The tests were spurred by structural failure of the B-1 exhaust nozzle external flaps and similar damage on the F-15. The test was performed using two 5/8 in. ID pipes machined and placed side-by-side to mimic B-1 nozzles. A microphone mounted on the internozzle fairing measured acoustic levels near the nozzle exit plane. The nozzles oscillated significantly more than did a single nozzle over a wide range of nozzle pressure ratios. Acoustic levels in the dual jets exceeded single jet noise by as much as 20 dB, making acoustic resonance a definite candidate for structural damage in the twin jet configuration.

Norum, T. D.↗
NASA NTRS1954

Thrust characteristics of a series of convergent-divergent exhaust nozzles at subsonic and supersonic flight speeds

An experimental investigation of a series of four convergent-divergent exhaust nozzles was conducted in the Lewis 8-by-6 foot supersonic wind tunnel at Mach numbers of 0.1, 0.6, 1.6, and 2.0 over a range of nozzle pressure ratios. The thrust characteristics of these nozzles were determined by a pressure-integration technique. From a thrust standpoint, a nozzle designed to give uniform parallel flow at the exit had no advantage over the simple geometric design with conical convergent and divergent sections. The rapid-divergent nozzles might be competitive with the more gradual-divergent nozzles since the relatively short length of these nozzles would be advantageous from a weight standpoint and might result in smaller thrust losses due to friction. The thrusts, with friction losses neglected, were predicted satisfactorily by one-dimensional theory for the nozzles with relatively gradual divergence. The thrusts of the rapid-divergent designs were several percentages below the theoretical values at the design pressure ratio or above, while at low pressure ratios there was a considerable effect of free-stream Mach number, with thrusts considerably above theoretical values at subsonic speeds and somewhat above theoretical values at supersonic speeds. This Mach numb effect appeared to be related to the variation of the model base pressure with free-stream Mach number.

Fradenburgh, Evan A↗
NASA NTRS2004

Generation 1.5 High Speed Civil Transport (HSCT) Exhaust Nozzle Program

The objective of this program was to conduct an experimental and analytical evaluation of low noise exhaust nozzles suitable for future High-Speed Civil Transport (HSCT) aircraft. The experimental portion of the program involved parametric subscale performance model tests of mixer/ejector nozzles in the takeoff mode, and high-speed tests of mixer/ejectors converted to two-dimensional convergent-divergent (2-D/C-D), plug, and single expansion ramp nozzles (SERN) in the cruise mode. Mixer/ejector results show measured static thrust coefficients at secondary flow entrainment levels of 70 percent of primary flow. Results of the high-speed performance tests showed that relatively long, straight-wall, C-D nozzles could meet supersonic cruise thrust coefficient goal of 0.982; but the plug, ramp, and shorter C-D nozzles required isentropic contours to reach the same level of performance. The computational fluid dynamic (CFD) study accurately predicted mixer/ejector pressure distributions and shock locations. Heat transfer studies showed that a combination of insulation and convective cooling was more effective than film cooling for nonafterburning, low-noise nozzles. The thrust augmentation study indicated potential benefits for use of ejector nozzles in the subsonic cruise mode if the ejector inlet contains a sonic throat plane.

Thayer, E. B.↗
NASA NTRS1975

Summary of nozzle-exhaust plume flowfield analyses related to space shuttle applications

Exhaust plume shape simulation is studied, with the major effort directed toward computer program development and analytical support of various plume related problems associated with the space shuttle. Program development centered on (1) two-phase nozzle-exhaust plume flows, (2) plume impingement, and (3) support of exhaust plume simulation studies. Several studies were also conducted to provide full-scale data for defining exhaust plume simulation criteria. Model nozzles used in launch vehicle test were analyzed and compared to experimental calibration data.

Penny, M. M.↗
NASA NTRS1983

Thrust performance of a variable-geometry, divergent exhaust nozzle on a turbojet engine at altitude

A variable geometry, low aspect ratio, nonaxisymmetric, two dimensional, convergent-divergent exhaust nozzle was tested at simulated altitude on a turbojet engine to obtain baseline axial, dry thrust performance over wide ranges of operating nozzle pressure ratios, throat areas, and internal expansion area ratios. The thrust data showed good agreement with theory and scale model test results after the data were corrected for seal leakage and coolant losses. Wall static pressure profile data were also obtained and compared with one dimensional theory and scale model data. The pressure data indicate greater three dimensional flow effects in the full scale tests than with models. The leakage and coolant penalties were substantial, and the method to determine them is included.

Straight, D. M.↗
NASA NTRS1972

Analysis and design of three dimensional supersonic nozzles. Volume 1: Nozzle-exhaust flow field analysis by a reference plane characteristics technique

A second order numerical method employing reference plane characteristics has been developed for the calculation of geometrically complex three dimensional nozzle-exhaust flow fields, heretofore uncalculable by existing methods. The nozzles may have irregular cross sections with swept throats and may be stacked in modules using the vehicle undersurface for additional expansion. The nozzles may have highly nonuniform entrance conditions, the medium considered being an equilibrium hydrogen-air mixture. The program calculates and carries along the underexpansion shock and contact as discrete discontinuity surfaces, for a nonuniform vehicle external flow.

Dash, S.↗
NASA NTRS1982

Performance of a 2D-CD nonaxisymmetric exhaust nozzle on a turbojet engine at altitude

Baseline thrust and cooling data obtained with a 2D-CD versatile research exhaust nozzle mounted on a turbojet engine in an altitude chamber are presented. The tests covered a range of nozzle pressure ratios, nozzle pressure ratios, nozzle throat areas, and internal expansion area ratios. The thrust data obtained show good agreement with theory and scale model results after correcting the data for leakage and bypass cooling flows. Additional work is needed to improve predictability of cooling performance.

Straight, D. M.↗