Search NASA⌕ Search

SEARCH · Search NASA

Results for “Edge tone”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

79 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Screech Tones from Rectangular Jets with Spanwise Oblique Shock-Cell Structures

Understanding screech is especially important for the design of advanced aircraft because screech can cause sonic fatigue failure of aircraft structures. Although the connection between shock-cell spacing and screech frequency is well understood, the relation between non-uniformities in the shock-cell structures and the resulting amplitude, mode, and steadiness of screech have remained unexplored. This paper addresses the above issues by intentionally producing spanwise (larger nozzle dimension) variations in the shock-cell structures and studying the resulting spanwise screech mode. The spanwise oblique shock-cell structures were produced using imperfectly expanded convergent-divergent rectangular nozzles (aspect ratio = 5) with nonuniform exit geometries. Three geometries were studied: (a) a nozzle with a spanwise uniform edge, (b) a nozzle with a spanwise oblique (single bevelled) edge, and (c) a nozzle that had two spanwise oblique (double bevelled) cuts to form an arrowhead-shaped nozzle. For all nozzles considered, the screech mode was antisymmetric in the transverse (smaller nozzle dimension) direction allowing focus on changes in the spanwise direction. Three types of spanwise modes were observed: symmetric (1), antisymmetric (2), and oblique (3). The following significant results emerged: (1) for all cases the screech mode corresponds with the spanwise shock-cell structure, (2) when multiple screech modes are present, the technique presented here makes it possible to distinguish between coexisting and mutually exclusive modes, (3) the strength of shocks 3 and 4 influences the screech source amplitude and determines whether screech is unsteady. The results presented here offer hope for a better understanding of screech and for tailoring shock-containing jets to minimize fatigue failure of aircraft components.

Raman, Ganesh↗
NASA NTRSDate not supplied

Source Diagnostic Fan II (22-inch) Duct Mode Characteristics as Measured by the Rotating Rake Mode Measurement System while Operated in the NASA Glenn 9x15 Low Speed Wind Tunnel

The second entry of the Source Diagnostic Test (SDT2) was a continuation of the first SDT entry with additional parameters tested. The rotor, stators, and general flow path hardware used in SDT2 were the same as those for SDT1. This included a radial baseline set of stator vanes, which had a vane count such that the rotor-stator interaction at the fan blade passing fundamental was cut-off, as is typical for modern turbofans. Two sets of stator vanes were designed and tested with a count generating a cut-on rotor-stator interaction at the fan blade passing fundamental. One of the sets maintained the no aerodynamic sweep as the radial baseline, the other was designed with leading edge sweep with the intent to generate lower noise. The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present. The system is a radial rake immersed into the duct that continuously rotates about the duct centerline. For each of the three stator vane configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator interaction mode acoustic levels. Multiple-pure tones generated by the M5 rotor in the inlet were also measured.

Turbofan, Duct Modes↗
NASA NTRSDate not supplied

Source Diagnostic Fan II (22-inch) Duct Mode Characteristics as Measured by the Rotating Rake Mode Measurement System while Operated in the NASA Glenn 9x15 Low Speed Wind Tunnel

The second entry of the Source Diagnostic Test (SDT2) was a continuation of the first SDT entry with additional parameters tested. The rotor, stators, and general flow path hardware used in SDT2 were the same as those for SDT1. This included a radial baseline set of stator vanes, which had a vane count such that the rotor-stator interaction at the fan blade passing fundamental was cut-off, as is typical for modern turbofans. Two sets of stator vanes were designed and tested with a count generating a cut-on rotor-stator interaction at the fan blade passing fundamental. One of the sets maintained the no aerodynamic sweep as the radial baseline, the other was designed with leading edge sweep with the intent to generate lower noise. The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present. The system is a radial rake emersed into the duct that continuously rotates about the duct centerline. For each of the three stator vane configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator interaction mode acoustic levels. Multiple-pure tones generated by the M5 rotor in the inlet were also measured.

Turbofan↗
NASA NTRSDate not supplied

Investigation of the 30P30N Slat Flow Field with Passive Control Devices Using Particle Image Velocimetry

The leading-edge slat of a high-lift wing is one of the main noise contributors during approach and landing. This paper describes an experimental investigation of the velocity field associated with multiple passive noise treatments, including slat-cusp extensions, a cove filler, and a gap filler, on a two-dimensional multi-element high-lift 30P30N airfoil. Previous work documented comparisons of both surface and far field pressure fluctuations in the presence of these devices with those for a baseline case at different flow conditions. However, important information related to the velocity fields was missing from the previous measurements, hindering our ability to elucidate the changes in the flow physics associated with the noise treatments. Therefore, two-component Particle Image Velocity has been used to investigate the influence of passive noise treatments on the flow fields. All measurements are taken at an effective, free-air angle of attack of 5.5 degrees and a stowed-chord-based Reynolds number of 1.71 × 10e6. The measurements show that the slat extensions shorten the slat-cove shear layer trajectory, resulting in reduced growth of disturbances within the slat-cove shear layer. This leads to a shift of tonal peaks to higher frequencies and a reduction in the tonal amplitudes. The gap filler blocks the flow path through the gap, causing the reattachment location to shift to the main wing leading edge lower surface. Consequently, the feedback loop associated with the flow-acoustic interaction in the baseline case is eliminated, and the turbulent kinetic energy in the slat-cove shear layer is significantly reduced. However, extensive flow separation is observed on the suction side of the gap filler, which does not eliminate the noise reduction benefit due to the gap filler, but does degrade the aerodynamic performance of the high-lift configuration. Finally, the overall flow field in the presence of the cove filler is similar to that in the baseline case at the design angle of attack, but the slat-cove shear layer is eliminated leading to a suppression of the cavity tones associated with the shear layer. This change accounts for the reduction in slat noise as measured in previous work.

Aeroacoustics↗
NASA NTRS2007

Noise Benefits of Rotor Trailing Edge Blowing for a Model Turbofan

An advanced model turbofan was tested in the NASA Glenn 9- by 15-Foot Low Speed Wind Tunnel (9x15 LSWT) to explore far field acoustic effects associated with rotor Trailing-Edge-Blowing (TEB) for a modern, 1.294 stage pressure ratio turbofan model. The TEB rotor (Fan9) was designed to be aerodynamically similar to the previously tested Fan1, and used the same stator and nacelle hardware. Fan9 was designed with trailing edge blowing slots using an external air supply directed through the rotor hub. The TEB flow was heated to approximate the average fan exit temperature at each fan test speed. Rotor root blockage inserts were used to block TEB to all but the outer 40 and 20% span in addition to full-span blowing. A configuration with full-span TEB on alternate rotor blades was also tested. Far field acoustic data were taken at takeoff/approach conditions at 0.10 tunnel Mach. Far-field acoustic results showed that full-span blowing near 2.0% of the total flow could reduce the overall sound power level by about 2 dB. This noise reduction was observed in both the rotor-stator interaction tones and for the spectral broadband noise levels. Blowing only the outer span region was not very effective for lowering noise, and actually increased the far field noise level in some instances. Full-span blowing of alternate blades at 1.0% of the overall flow rate (equivalent to full-span blowing of all blades at 2.0% flow) showed a more modest noise decrease relative to full-span blowing of all blades. Detailed hot film measurements of the TEB rotor wake at 2.0% flow showed that TEB was not every effective for filling in the wake defect at approach fan speed toward the tip region, but did result in overfilling the wake toward the hub. Downstream turbulence measurements supported this finding, and support the observed reduction in spectral broadband noise.

Woodward, Richard P.↗
NASA NTRS1999

Design of a Low Speed Fan Stage for Noise Suppression

This report describes the design of a low tip speed, moderate pressure rise fan stage for demonstration of noise reduction concepts. The fan rotor is a fixed-pitch configuration delivering a design pressure ratio of 1.378 at a specific flow of 43.1 lbm/sec/sq ft. Four exit stator configurations were provided to demonstrate the effectiveness of circumferential and axial sweep in reducing rotor-stator interaction tone noise. The fan stage design was combined with an axisymmetric inlet, conical convergent nozzle, and nacelle to form a powered fan-nacelle subscale model. This model has a 22-inch cylindrical flow path and employs a rotor with a 0.30 hub-to-tip radius ratio. The design is fully compatible with an existing NASA force balance and rig drive system. The stage aerodynamic and structural design is described in detail. Three-dimensional (3-D) computational fluid dynamics (CFD) tools were used to define optimum airfoil sections for both the rotor and stators. A fan noise predictive system developed by Pratt & Whitney under contract to NASA was used to determine the acoustic characteristics of the various stator configurations. Parameters varied included rotor-to-stator spacing and vane leading edge sweep. The structural analysis of the rotor and stator are described herein. An integral blade and disk configuration was selected for the rotor. Analysis confirmed adequate low cycle fatigue life, vibratory endurance strength, and aeroelastic suitability. A unique load carrying stator arrangement was selected to minimize generation of tonal noise due to sources other than rotor-stator interaction. Analysis of all static structural components demonstrated adequate strength, fatigue life, and vibratory characteristics.

Dalton, W. N.↗
NASA NTRS2017

AI and Autonomy Initiatives for NASA’s Deep Space Network (DSN)

NASA’s Deep Space Network (DSN) consists of thirteen large (34- and 70-meter) antennas that are used to communicate with approximately 40 NASA and partner spacecraft, all at great distance from the earth (generally at Lunar distances and beyond). The DSN has a long history — over 50 years — and has evolved with cutting edge, often custom, telecommunications equipment and associated software systems. In recent years, and in preparation for an increasing future demand, there has been an effort to invest in initiatives that will result in significant cost savings in the future. These efforts are building on, or augmenting, the recent deployment of “Follow-the-Sun” operations (day shift remote operational control of the entire network from each of the three antenna complexes in turn) — which is being deployed in 2017. This paper focuses on Adaptive Demand Access: in a paradigm shift from completely pre-planned operations, this concept calls for spacecraft to signal their intent (or not) for near-future contacts, in case they have science results of interest, or have experienced an anomaly. This would take advantage of a beacon tone transmission, which can be detected using smaller antennas. When a connection request is received, the DSN ground systems would adaptively accommodate the request, inserting the contact into the plan as soon as possible, subject to constraints and priorities. The demand access concept incorporates onboard data analysis and science data processing, so that beacon tones can be generated with maximum information. This area is representative of several where infusing AI technologies can lead to improved effectiveness of the DSN as the network readies for support of expanded Mars exploration efforts in the 2020’s and beyond.

Wyatt, E. Jay↗