Search NASA⌕ Search

SEARCH · Search NASA

Results for “Embodied carbon”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Strain Sensors, Methods of Making Same, and Applications of Same

In one aspect, the present invention relates to a layered structure usable in a strain sensor. In one embodiment, the layered structure has a substrate with a first surface and an opposite, second surface defining a body portion therebetween; and a film of carbon nanotubes deposited on the first surface of the substrate, wherein the film of carbon nanotubes is conductive and characterized with an electrical resistance. In one embodiment, the carbon nanotubes are aligned in a preferential direction. In one embodiment, the carbon nanotubes are formed in a yarn such that any mechanical stress increases their electrical response. In one embodiment, the carbon nanotubes are incorporated into a polymeric scaffold that is attached to the surface of the substrate. In one embodiment, the surfaces of the carbon nanotubes are functionalized such that its electrical conductivity is increased.

Biris, Alexandru S.↗
DOE OSTI2022

Embodied Energy in Pyrolysis and Solvolysis Approaches to Recycling for Carbon Fiber-Epoxy Reinforced Composite Waste Streams

Carbon fiber composites are increasingly used in aerospace, motorcycles, sporting, and high-performance vehicles, and their end of life recycling is of growing interest. This study deals with the life cycle assessment (LCA) of carbon fiber reinforced plastics (CFRP) waste streams. The embodied energy (EE) of recycling CFRP via two viable methods—i.e., pyrolysis and solvolysis—is studied. Both pyrolysis and solvolysis were studied for EE with different variants. Alongside fiber recovery from CFRP, the pyrolysis process calculations consider energy recovery from syngas and oil produced within the system. For pyrolysis, electric furnace and natural gas were primarily considered. For solvolysis, different solvent scenarios were considered, including (a) deionized water, (b) water and potassium hydroxide, (c) acetone and water, and (d) water with acetic acid and potassium hydroxide. Energy reduction from one generation to the next has also been highlighted. The EE for recycling CFRP is quantified and discussed for these scenarios in this paper.

composites↗
DOE OSTI2020

Fabrication of multilayered carbon MEMS devices

The various technologies presented herein relate to formation of carbon micromechanical systems (CMEMS), wherein the CMEMS comprise multiple layers of carbon structures and are formed using a plurality of photoresist precursors that are processed to form carbon. The various embodiments can be utilized in producing a plurality of CMEMS with full production level fabrication, e.g., 6 inch wafers can be processed. A pyrolyzed layer of carbon is lithographically defined after pyrolysis, wherein the post-pyrolysis etch process can produce carbon structures having repeatable and accurate device geometries, with straight sidewalls. A sacrificial layer can be applied to facilitate separation of a first carbon layer from a second carbon layer, wherein, upon pyrolysis to form the second carbon layer and lithography thereof, the sacrificial layer is removed to form a CMEMS comprising a first carbon layer (e.g., comprising bottom contacts) located beneath a second carbon layer (e.g., a mechanical layer).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Printable Fiber Reinforced Cement Composites – Feasibility Study

Additive manufacturing is enabling the manufacturability of structures with previously unattainable complexity or functionality, and there is growing interest in additive manufacturing of “printed” concrete structures. The focus of this Phase 1 Technical Collaboration (TC) project was to evaluate feasibility of printing hybrid cement composite structures reinforced with textile carbon fibers (tCF). This project leverages other (non-IACMI) projects on cement formulation and printing process development, as well as on the production process for tCF. This project’s primary focus was to explore cement composite mix design with textile carbon fibers to be manufactured by MonteFibre (TC partner) and evaluate suitable fiber-matrix interface or sizing for cement composites working with Michelman (TC Partner). This project supports IACMI’s goal of reducing the cost and embodied energy of carbon fiber composites. Cost is one of the fundamental challenges to carbon fiber reinforced cement composites. Cement is an extremely inexpensive material (approximately $\$$0.05/lb). Adding 1 wt% of conventional carbon fiber to cement quadruples its cost. Therefore, the need to use low-cost carbon fiber and ensure that the additional cost of the carbon fiber has a greater cost benefit to the final product. This was the first preliminary evaluation to integrate tCF reinforcement in cement composites, and such potential tCF utilization should significantly reduce materials cost. Cement composite production is energy and emissions intensive, thus by strengthening it less material will be required. Hence, the embodied energy and production time of the resulting structures will be reduced. Additionally, integrating these new materials into additive processes can enable selective use of the material in high load or stress areas. It is noteworthy that past work in this field of fiber reinforced cement composites did not consider the optimization of fiber-matrix interface using suitable sizing. Carbon fiber reinforcement offers potential added benefits of thermal conductivity (which affects cure rate) and flow behavior that could provide opportunities for site specific utilization of carbon fiber on hybrid cement structures (e.g. use the fiber reinforcement on outer surfaces to enhance strength and modulus and then infiltrating the internal structures with conventional concrete). MonteFibre was the industry lead and planned on supplying the tCF for this project. However, during the short Phase-1 duration of this project, MonteFibre was unable to produce tCF for this project due to manufacturing plant being off-line throughout the course of the project. The project team decided to pursue an alternate option which involved demonstrating printable concrete with steel fibers by the ORNL lead, Dr. Brian Post. The University of Tennessee collaboration team focused on evaluating the suitable chemical sizing for carbon fibers working with Michelman and also developed methods for material characterization of cement-based composites to evaluate the material response for compression, shear, flexure, and tension. The two milestones for University of Tennessee, Knoxville were realized related to identification of one sizing suitable for carbon fiber reinforced cement composite and developing data associated with mechanical behavior of unreinforced (neat) and carbon fiber reinforced cement composites. ORNL could not complete the task of carbon fiber reinforced printed cement composites due to the reasons mentioned earlier, but was able to replace tCF with steel fibers to demonstrate the feasibility of printing with fiber reinforced cement composites. The Project team reviewed possible sizing chemistry available in collaboration with Michelman for use on carbon fiber reinforcement in cement composites and concrete applications. Our initial goal was to identify a sizing most promising for formulation with textile carbon fibers (tCF) to deliver excellent mechanical properties in composite material state. Since tCF was not available for this project as originally envisioned, the team continued this task to identify a suitable sizing for carbon fiber applications by applying such sizing to lower cost carbon fibers currently available commercially from Zoltek called Panex fibers. At a future time this can be optimized for textile carbon fibers from Montefibre. The bulk of previous work on carbon fiber reinforced cement has neglected the importance of fiber-matrix adhesion on mechanical properties of the cement composite and identifying this missing link was an important accomplishment for future research. Tensile behavior of fiber reinforced concrete is important to evaluate in order to realize the dream of concrete products that do not need reinforcing steel. Important sample preparation and testing procedures were addressed in this study and it was concluded that substantial improvements in tensile behavior, without compromising compressive strength, and improved ductility can result from the use of carbon fiber reinforcement.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Whole-building life-cycle analysis with a new GREET® tool: Embodied greenhouse gas emissions and payback period of a LEED-Certified library

Embodied greenhouse gas (GHG) emissions of building components and buildings operations need to be quantified to holistically address building sustainability. To evaluate embodied GHG emissions of buildings and to provide insights on building materials and building design decisions toward decarbonization, we have recently created a building life-cycle assessment (LCA) module in the widely used Greenhouse gases, Regulated Emissions, and Energy use in Technologies (GREET (R)) LCA model. We applied the GREET building LCA module to examine embodied GHG impacts and the payback period of a LEED (Leadership in Energy and Environmental Design) certified public library in Chicago, USA. We developed localized, detailed life-cycle inventories to address individual building materials used in the library. We expanded the LCA system boundary to include the mechanical, electrical, and plumbing system, as well as refrigerant impacts, which are often ignored in previous studies. Results show that the total embodied GHG emissions are approximately 817 metric tons, or approximately 538 kg/m 2 . Sensitivity analysis highlights the positive role of increasing the use of recycled materials for reducing embodied GHG emissions. Sensitivity analysis on embodied GHG emissions payback periods shows the need to benchmark the embodied and operational carbon performance of buildings for comparison to alternative building designs and sustainability practices. Furthermore, this analysis demonstrates that building LCA models, such as the GREET building LCA module, which addresses embodied and operational GHG emission impacts of whole buildings holistically, could empower building architects, technology developers, manufacturers, and general contractors to address embodied and operational impacts holistically for building sustainability.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1982

Method and device for detection of a substance

A device is disclosed in which a discharge grid is provided that has a sufficiently high voltage potential across its grid electrodes so that a substance with predetermined characteristics causes an electric spark discharge to occur between electrodes. The electric spark discharge alters the predetermined characteristics of the substance by oxidation and/or vaporization so that the substance is no longer detectable by an electric spark discharge. A means is provided for counting the number of electric spark discharges. This count indicates the concentration of the substance having the predetermined characteristics. One embodiment disclosed detects longitudinally extending carbon fibers suspended in a gaseous medium. Another embodiment provides for the detection of carbon fibers adhesively attached to a collection tape. The tape is positioned against the discharge grid and a high voltage is periodically applied across the grid electrodes until electric spark discharges no longer occur.

Yang, L. C.↗
NASA NTRS2015

Systems and Methods for Fabricating Carbon Nanotube-Based Vacuum Electronic Devices

Systems and methods in accordance with embodiments of the invention proficiently produce carbon nanotube-based vacuum electronic devices. In one embodiment a method of fabricating a carbon nanotube-based vacuum electronic device includes: growing carbon nanotubes onto a substrate to form a cathode; assembling a stack that includes the cathode, an anode, and a first layer that includes an alignment slot; disposing a microsphere partially into the alignment slot during the assembling of the stack such that the microsphere protrudes from the alignment slot and can thereby separate the first layer from an adjacent layer; and encasing the stack in a vacuum sealed container.

Manohara, Harish↗
NASA NTRS2014

Carbon Fiber Foam Composites and Methods for Making the Same

Exemplary embodiments provide methods and apparatus of forming fibrous carbon foams (FCFs). In one embodiment, FCFs can be formed by flowing a fuel rich gas mixture over a catalytic material and components to be encapsulated in a mold to form composite carbon fibers, each composite carbon fiber having a carbon phase grown to encapsulate the component in situ. The composite carbon fibers can be intertwined with one another to form FCFs having a geometry according to the mold.

Leseman, Zayd Chad↗
DOE OSTI2022

Crack width control and mechanical properties of low carbon engineered cementitious composites (ECC)

Engineered Cementitious Composites (ECC) have superior properties with high tensile ductility and tight crack width compared to conventional concrete. The properties of ECC are significantly influenced by the material composition which can be tailored to enhance the sustainability of ECC. Towards this goal, recycled crumb rubber (CR) and silica fume (SF) were used to tailor the properties of a polypropylene-fiber reinforced ECC with a low carbon binder based on limestone calcined clay cement (LC3) in this study. Crumb rubber was found to be effective in enhancing strain-hardening performance and reducing the width of the multiple microcracks. However, a loss of compressive strength was accompanied by an increasing amount of CR. While silica fume or lower w/b ratio enhanced the compressive strength, the crack width of ECC increased at higher SF content or lower w/b. The underlying mechanisms of these trends were traced to the alteration of the matrix fracture toughness and fiber/matrix interfacial bond. Rubber particle bridging was found to contribute to crack width control. Finally, the combined use of the LC3 green binder and CR led to a lowering of the embodied and operational carbon footprint of ECC.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical and self-healing behavior of low carbon engineered cementitious composites reinforced with PP-fibers

While the ultrahigh tensile ductility and superior durability of Engineered Cementitious Composites (ECC) have been demonstrated, the relatively high energy and carbon intensity, as well as high material cost present potential impediments to broader ECC applications. The objective of this research is to develop a more sustainable and cost-effective ECC. The ordinary Portland cement (OPC) and the commonly used PVA fiber in conventional ECC were replaced by limestone calcined clay cement (LC3) and polypropylene (PP) fiber, respectively. The ECC compressive strength, tensile stress-strain relationship, and microcrack self-healing behavior were studied at three water to binder ratios (0.3, 0.2, 0.16). The novel LC3-PP-ECC showed a tensile strain capacity of greater than 6% and an intrinsically tight crack width below 82 μm when loaded to 1% tensile strain. Further, the LC3-PP-ECC demonstrated efficient recovery of the composite tensile ductility and ultimate tensile strength through self-healing. Compared to typical ECC made with OPC and PVA fiber, the material cost, embodied energy and carbon footprint of LC3-PP-ECC are reduced by 61%, 45%, and 48%, respectively. Here, the superior mechanical properties and durability combined with the low environmental impact and cost for material production promote LC3-PP-ECC as a sustainable material for structural and non-structural applications.

42 ENGINEERING↗
DOE OSTI2024

Upcycling of Mixed Aluminum Alloy Shredder Scrap using Shear Processing

Conservation of critical materials is an increasing area of focus in the Unites States. In 2023, aluminum was added to the US Department of Energy Final Critical Materials List which has spurred public and private research into sustainable management of these resources. Additionally, efficiency in manufacturing and conservation of natural resources are growing concerns with targets to lower global carbon emissions, as primary aluminum alloy production is energy intensive, requiring 14 MWh of electricity plus 0.4 tonnes of CO2 per tonne of Al. Due to these factors, is essential that more sustainable manufacturing methods for aluminum alloys are developed going forward. To this end, much research is ongoing on the topic of more efficient utilization and recovery. However, most of this research still requires primary aluminum in the production process. Here, it will be attempted to bypass the use of primary aluminum and produce useful material recycled from 100% post-consumer scrap. Even considering recent developments in recycling of Al scrap, there is still a large amount of post-consumer scrap that is underutilized due to high impurity content, and that amount will increase significantly as more and more aluminum alloys are utilized in vehicles. This “scrap wave” is expected to cover 80% of the demand for automotive aluminum alloys by 2050 . A challenge to be addressed before the coming scrap wave can be fully utilized is that the tolerance of manufacturing techniques to impurities or off-spec alloy compositions must be increased. Particularly, in 5000-and 6000-series alloys (the most common wrought alloys in durable products), excess iron, copper, and silicon create brittle intermetallics during casting that remain in the extruded microstructure which limit the formability, ductility, and corrosion resistance of the alloy. Concerningly, many of the highest-volume post-consumer aluminum scrap streams such as automotive shredder scrap contain a mix of alloys including both wrought and cast alloys. Their compositions can vary widely depending on geography and the time of year. Because they are mixed, they often contain high content of multiple alloying elements such as Si and Cu in higher concentrations than are found in typical wrought alloys. They may also be contaminated with non-Al alloys from fasteners that get mixed in and often have high content of unwanted elements such as Fe. As a method for utilizing these underused scrap streams that are high in tramp elements, an emerging extrusion technology is being developed at the Pacific Northwest National Laboratory (PNNL) that aims to upcycle 100% post-consumer aluminum scrap directly into extruded components without the addition of primary aluminum . This new technology, called Shear Assisted Processing and Extrusion (ShAPE), is enabling a shift away from today’s recycling paradigm by reaching deeper into lower-value scrap streams, using shredder scrap as the extrusion billet material. Sometimes referred to as Twitch or Tweak, these scrap streams result from shredding and sorting of automobiles, building materials, appliances, and consumer goods. ShAPE combines the linear axis of conventional extrusion with a rotating extrusion die. This rotating die applies large strain to the material during extrusion, which breaks up large impurity-containing intermetallic particles, reducing their deleterious effects. This has been demonstrated for 6063 machining scrap spiked with excess Fe, and Twitch scrap high in Fe, Si and Cu where strength and ductility were retained for both feedstock compositions. Additionally, the extreme plastic deformation during ShAPE enables extrusion of billets with high Si that are too brittle for processing by conventional extrusion. By using 100% post-consumer shedder scrap as feedstock, ShAPE has the potential to slash embodied energy and carbon in extruded components by >80% compared to conventional extrusion of primary aluminum alloys.

Milligan, Brian K.↗
DOE OSTI2024

Surrogate-assisted optimization under uncertainty for design for remanufacturing considering material price volatility

Remanufacturing is a well-established end-of-life (EOL) strategy that promises significant savings in energy and carbon emissions. However, the current design practices are not remanufacturing-inclusive, i.e., the majority of products are designed for a single life cycle. As a result, potential products that can sustain multiple life cycles are deprived of additional benefits of being designed for remanufacturing, such as reduced material usage, lower cost, and improved environmental impact. Moreover, the uncertainty in design, material selection, and economics are not considered to produce remanufacturable designs. Accordingly, this research proposes a design for remanufacturing (DfRem) framework that accounts for design uncertainty and material price volatility. The framework systematically explores the design space, performs design optimization under uncertainty, followed by topology optimization to provide additional mass savings, and finally, a price volatility analysis for plausible design material choices. The candidate designs are evaluated based on their design mass, material price volatility, failure mode characteristics, carbon footprint, and embodied energy impacts. The proposed framework's utility is demonstrated via the use of an engine cylinder head case study subjected to thermo-mechanical loads along with fatigue and wear failure. Considering grey cast iron and aluminum alloy as the design material choices, it was found that the cast iron design reduced the initial design mass by 6% as opposed to a 5% decrease for aluminum. On the other hand, about 8% area of the cast iron design failed due to fatigue, compared to 3% for aluminum. Here, we further observed that although the aluminum design provided better mechanical performance than the cast iron design, this material was more expensive and volatile in price.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development of Large Scale Extrusion Deposition for Structural Applications

Large Scale Extrusion Deposition (LSED) is an evolving additive manufacturing (AM) technology that research, such as that taking place at Oak Ridge National Laboratory (ORNL) and companies like Local Motors, are continuing to utilize and develop new applications. A major LSED application of interest has been molds and tooling as it allows for much shorter production time and lower cost. However, interest has been expanding into using LSED for more structural applications due to more frequent use of high performing polymer composites as feedstock. The use of LSED for structural applications is of particular interest to Local Motors as it is currently being used to create commercially viable, energy efficient electric vehicles. LSED offers a unique opportunity when compared to traditional manufacturing methods as it can significantly reduce the number of components necessary, while decreasing embodied energy and carbon emissions. Even with these benefits however, it is important that LSED is properly understood from a structural aspect as this field has not been as heavily researched as tooling. To ensure a high level of safety and repeatability is an essential responsibility of a manufacturer whose products are structural in nature. As such it is important to understand the materials and LSED process to make structural objects that the manufacturer can be confident in. The main goals of this project were to: develop and investigate materials that are of interest for structural LSED applications, further develop and understand the current machines used in LSED and develop simulations tools of LSED and the mechanical properties of the created structure. Material development focused on composite materials that have high mechanical properties and are stable in a variety of environments. The materials were tested to determine their as printed mechanical and thermal properties as these are necessary for simulations. Once the materials were investigated thoroughly, it allowed for simulations to be performed to compare to experimental data with simulations. Materials were also vetted to determine candidates for multi-material printing. The machine development focused around the areas of process monitoring, non-destructive evaluation, and quality control. Finally, the goal of the simulations was to develop a realistic model of printed structures, including in-process simulation and dynamic simulation. The routes to get to some of these goals and the depth in which they were investigated changed throughout the project due to personnel changes and the COVID-19 pandemic. This project resulted in many valuable results such as the development of an nondestructive evaluation (NDE) technique for interlayer defects, proof of simulation for warpage in simple parts, the development and utilization of a profilometer to monitor a print for defects or inconsistencies, thorough investigation of a material used commercially for structural LSED applications and valuable experimental data on the applicability and advantages of multi-material crush structures versus their neat counterparts by creation and testing of samples.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Apparatus and method for destructive removal of particles contained in flowing fluid

An apparatus and method for destructively removing particles from a flowing gas containing the particles is described. In the specific embodiments disclosed the apparatus is adapted to remove carbon particles from diesel engine exhaust products. The exhaust products are directed to a predetermined location where they are rapidly vaporized and combine with oxygen in the exhaust products to form carbon dioxide. Vaporization in one embodiment is effected by a discharge grid located within an exhaust conduit, the grid being chosen so that alternate conductors defining the grid are spaced apart a distance approximately 125 times the mean diameter of the particles to be removed. A voltage differential of approximately 690 volts is applied across adjacent conductors.

Yang, L. C.↗
DOE OSTI2022

Carbon supports for oxygen reduction catalysts

The invention provides a method of making a electrocatalyst from waste tires. The method comprises the steps of providing rubber pieces; optionally contacting the rubber pieces with a sulfonation bath to produce sulfonated rubber; pyrolyzing the rubber to produce tire-derived carbon composite comprising carbon black, wherein the pyrolyzing comprises heating to at least 200° C.-2400° C.; activating the tire-derived carbon composite by contacting the tire-derived carbon composite with an alkali anion compound to provide activated tire-derived carbon supports; and loading the activated carbon-based supports with platinum cubes. In another embodiment, the tire-derived carbon composite is activated by annealing in a carbon dioxide atmosphere.

Naskar, Amit K.↗
DOE OSTI2023

Investigation of pressure-controlled injection molding on the mechanical properties and embodied energy of recycled high-density polyethylene

Manufacturing with secondary feedstock has been identified as an effective strategy to improve plastic circularity. However, product quality inconsistencies arise due to variations in molecular weight, rheology, and mechanical properties. This work evaluates the processing of recycled high-density polyethylene using pressure-controlled injection molding with a focus on processing behavior and energy consumption. Further, the effects of injection velocity, packing pressure, and transfer position are benchmarked against a conventional velocity-controlled process. The experimental results show that the novel process control strategy significantly affects the mechanical properties, in-mold rheology, and energy consumption. Parts fabricated using pressure-controlled injection molding showed higher tensile properties due to increased macromolecular orientation. Additionally, reduced energy was used due to lower melt pressures required to completely replicate the cavity geometry. The results demonstrate the potential of the technology to support increased utilization of secondary feedstock and reduced carbon footprint.

36 MATERIALS SCIENCE↗
NASA NTRS2013

Bulk Cutting of Carbon Nanotubes Using Electron Beam Irradiation

According to some embodiments, the present invention provides a method for attaining short carbon nanotubes utilizing electron beam irradiation, for example, of a carbon nanotube sample. The sample may be pretreated, for example by oxonation. The pretreatment may introduce defects to the sidewalls of the nanotubes. The method is shown to produces nanotubes with a distribution of lengths, with the majority of lengths shorter than 100 tun. Further, the median length of the nanotubes is between about 20 nm and about 100 nm.

Ziegler, Kirk J.↗