Search NASA⌕ Search

SEARCH · Search NASA

Results for “Euler angles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Inertial measurement unit pre-processors and post-flight STS-1 comparisons

The flight results show that the relative tri-redundant Inertial Measurement Unit IMU performance throughout the entire entry flight was within the expected accuracy. Comparisons are presented which show differences in the accumulated sensed velocity changes as measured by the tri-redundant IMUs (in Mean Equator and Equinox of 1950.0), differences in the equivalent inertial Euler angles as measured with respect to the M50 system, and finally, preliminary instrument calibrations determined relative to the ensemble average measurement set. Also, differences in the derived body axes rates and accelerations are presented. Because of the excellent performance of the IMUs during the STS-1 entry, the selection as to which particular IMU would best serve as the dynamic data source for entry reconstruction is arbitrary.

Findlay, J. T.↗

Selected stability and control derivatives from the first Space Shuttle entry

Primary stability and control derivative estimates garnered from the first Shuttle entry are reported. The craft was the first vehicle to maneuver over a wide range of hypersonic velocities, yielding data on flight characteristics from previously unexplored regimes. The flight envelope was confined to entry and safe landing, with no additional maneuvers to gain control data. Data for a Mach number range of 25-1.5 and altitudes of 515,000-50,000 ft are provided, and functional ranges of the Shuttle control surfaces and attitude jets are outlined. On-board systems gathered data on aerodynamic coefficient identification, flight condition and Euler angles, and jet chamber pressures. A maximum likelihood estimation program, which contained unknown stability and control derivatives, was used for control; a control input determined the value of the unknown derivatives, and the input and spacecraft response were measured. Longitudinal and lateral directional maneuvers and their derivative estimates are described, noting wind contamination of the sideslip measurements below Mach 3. Further maneuvering and stability tests are projected for subsequent flights.

Iliff, K. W.↗

The investigation of tethered satellite system dynamics

A progress report is presented that deals with three major topics related to Tethered Satellite System Dynamics. The SAO rotational dynamics computer code was updated. The program is now suitable to deal with inclined orbits. The output has been also modified in order to show the satellite Euler angles referred to the rotating orbital frame. The three-dimensional high resolution computer program SLACK3 was developed. The code simulates the three-dimensional dynamics of a tether going slack taking into account the effect produced by boom rotations. Preliminary simulations on the three-dimensional dynamics of a recoiling slack tether are shown in this report. A program to evaluate the electric potential around a severed tether is immersed in a plasma. The potential is computed on a three-dimensional grid axially symmetric with respect to the tether longitudinal axis. The electric potential variations due to the plasma are presently under investigation.

Lorenzini, E.↗

Gibbs vector kinematics and inverse dynamics for decoupled spacecraft attitude maneuvers

By use of Gibbs vectors as kinematic variables, multi-axial spacecraft equations of rotational motion are shown to be globally and rationally feedback-equivalent to a set of unconstrained and decoupled harmonic oscillators, driven by generalized acceleration commands. Advantages over alternative formulations with Euler angles and quaternions are pointed out.

Dwyer, T. A. W., III↗

On-line identification and attitude control for SCOLE

This paper documents on-line linear least-square identification and attitude control of SCOLE, a laboratory apparatus representing an offset-feed antenna attached to the Space Shuttle. Identification is done autonomously by starting a slew maneuver in pitch or roll with reaction jets and observing the time history data of associated Euler angles when the jets are quiescent. Linear least-square analysis is used to select the parameters that best fit the output of an Autoregressive (AR) model to the data. The control effectiveness of the jets is determined in a subsequent test, again using linear least squares. The parameters so derived are used to design switching lines for time-optimal attitude control. This report describes the identification and control algorithms and the experimental apparatus and procedures used. Also, experimental data are presented that reflect the performance of the identification algorithms and the attitude control system.

Montgomery, R. C.↗

Direct inversion of rigid-body rotational dynamics

The global linearization (inversion) of rigid-body rotational dynamics is reviewed and representations in terms of quaternions and direction cosines are compared. Certain properties common to quaternions and direction cosines that make their use preferable to Euler angles and that simplify the inversion procedure are described. Applications of the inversion procedure for state estimation and attitude control are discussed. To avoid complexities caused by aerodynamics, an example of direct inversion for linear feedback control of spacecraft attitude is given.

Bach, Ralph↗

Dynamic modeling of multi-jointed mechanical systems for space applications

The dynamic formulation, modeling and motion simulation of multijointed open-chained mechanical systems as applied to space-based robotic systems are presented. Equations of motion are formulated in a unique manner based on a form of Lagrange's equations for quasi-coordinates (Boltzmann-Hamel equations). In order that kinematic joint constraints can be satisfied for the situation where some joints have less than three degrees of freedom, the equations are transformed into forms in terms of relative angular velocities and Euler angles. Rigid multibody examples are presented which show that the method can provide a dynamic model of systems of varying complexity.

Quinn, R. D.↗

Direct inversion of rigid-body rotational dynamics

The global linearization (inversion) of rigid-body rotational dynamics is reviewed, and representations in terms of quaternions and direction cosines are compared. Certain properties common to quaternions and direction cosines that make their use preferable to Euler angles and that simplify the inversion procedure are described. Applications of the inversion procedure for state estimation and attitude control are discussed. To avoid complexities caused by aerodynamics, an example of direct inversion for linear feedback control of spacecraft attitude is given.

Bach, Ralph↗

Rapid torque-bounded line-of-sight pointing of SCOLE with a designer's choice of initial alignment

Researchers simplified the analytical expression of the line of sight (LOS) error, discovered and proved the independence of Euler angle Psi, calculated attitude angles corresponding to 0 degrees and 20 degrees LOS errors, determined choices of initial alignment, tailored the slew maneuvers for LOS pointing, simulated numerically the LOS pointing slew of the Spacecraft Control Laboratory Experiment (SCOLE), and evaluated the pointing performance.

Lin, Jiguan Gene↗

The effects of gravity darkening on the ultraviolet continuum polarization produced by circumstellar disks

We investigate the effects of gravity darkening on the UV continuum polarization produced by an axisymmetric disk that surrounds a rapidly rotating star. Although the model is a single scattering approximation, we do include the effects of attenuation (electron scattering plus hydrogen bound-free absorption) by the disk, using an approach similar to that of Sobolev (1963). Because of the gravity darkening of the star and the attenuation within the disk, the radiation field is not axially symmetric about the radius vector. This implies that the polarization source functions are no longer provided by the finite disk depolarization factors of Cassinelli, Nordsieck, & Murison (1987), which are functions of the intensity moments in a spherically symmetric atmosphere. We reformulate the polarization source functions using generalized intensity moment tensors (J, H(sub i), K(sub ij)) that are valid for an arbitrary radiation field and envelope geometry. We find that the polarization source functions are simplest when using intensity moments in the observer's reference frame. On the other hand, the intensity moments are most easily evaluated in the stellar reference frame. Using the rotation transformation properties of the generalized intensity moments, we relate the observer's moments to those evaluated in the stellar reference frame. Our procedure for determining the polarization source functions thus merely involves choosing a set of Euler angles for the coordinate rotations, and then evaluating the associated rotation matrix. The geometrical complications of polarization transfer are thus reduced to obtaining a coordinate rotation matrix.

Bjorkman, J. E.↗

Determination of radio-frame position for Earth and Jupiter from Ulysses encounter tracking

Radio metric tracking data acquired from the Ulysses spacecraft about its encounter with Jupiter in February 1992 allow an accurate measurement of some components of the orbital elements describing the positions of the Earth and Jupiter with respect to extragalactic radio sources. Range and Doppler data acquired from the Earth while the spacecraft is far from any planet provide an estimate of the spacecraft trajectory relative to the orbit of the Earth. Doppler data near Jupiter provide an accurate position determination of the spacecraft with respect to Jupiter. Very Long Baseline Interferometry observations of the spacecraft with respect to the distant radio sources provide a direct measure of the spacecraft position in the radio reference frame. Combining these measurements provides a means to estimate the locations of the Earth and Jupiter in the radio reference frame. One of the three Euler angles describing the orientation of the Earth's orbit in the radio frame has been determined to an accuracy of 50 nanoradians; the result agrees with other recent determinations of this orientation. The position of Jupiter at the time of Ulysses encounter has been determined to 15 nanoradians in ecliptic latitude and longitude.

Folkner, W. M.↗

Registration assisted mosaic generation

This paper presents a general strategy for assembling mosaics from numerous individual images where uncertainty exists in the position and orientation of those images. Both of the presented applications relate to remotely operated camera platforms, the first being the Galileo solid state imaging (SSI) camera presently in orbit around Jupiter, and the second being the Imager for Mars Pathfinder (IMP) stereo camera on Mars. A basic strategy in both applications is to determine the correct relative camera pointing followed by direct map projection of the images. It is assumed that approximate camera pointing exists sufficient to locate adjacent images and to place initial tiepoints within reach of the correlator. Spatial correlation is used to fix tiepoints whose initial locations are predicted by the camera pointing. We use either an fast fourier transform (fft) algorithm or a variant of Gruen's scheme permitting limited image rotation and skew. The Gruen correlator has three hierarchical modes: 1) A classical spatial least squares correlation on integral pixel boundaries used when rotation is small. 2) An annealing non-deterministic search used when rotations are unknown. A simplex deterministic search used for the end game. The correlation operation can be performed either interactively or autonomously. The final camera pointing solution relies upon a simplex downhill search in 2n or 3n dimensions where n is the number of images comprising the mosaic and the objective function to be minimized is the disagreement between tiepoint locations predicted from the camera pointing with those observed by the correlator. For Galileo the 3n unknowns are euler angles defining camera pointing in planet coordinates, and for Mars Pathfinder they are 2n unknowns representing commanded azimuth and elevation in the Lander coordinate system.

Lorre, Jean J.↗

X33 Reusable Launch Vehicle Control on Sliding Modes: Concepts for a Control System Development

Control of the X33 reusable launch vehicle is considered. The launch control problem consists of automatic tracking of the launch trajectory which is assumed to be optimally precalculated. It requires development of a reliable, robust control algorithm that can automatically adjust to some changes in mission specifications (mass of payload, target orbit) and the operating environment (atmospheric perturbations, interconnection perturbations from the other subsystems of the vehicle, thrust deficiencies, failure scenarios). One of the effective control strategies successfully applied in nonlinear systems is the Sliding Mode Control. The main advantage of the Sliding Mode Control is that the system's state response in the sliding surface remains insensitive to certain parameter variations, nonlinearities and disturbances. Employing the time scaling concept, a new two (three)-loop structure of the control system for the X33 launch vehicle was developed. Smoothed sliding mode controllers were designed to robustly enforce the given closed-loop dynamics. Simulations of the 3-DOF model of the X33 launch vehicle with the table-look-up models for Euler angle reference profiles and disturbance torque profiles showed a very accurate, robust tracking performance.

Shtessel, Yuri B.↗

AXAF Coordinate Transformation at XRCF

Coordinate transformation between focal plane and detector pixel systems must be handled carefully at the X-ray Calibration Facility (XRCF) as it will be during flight. The High Resolution Mirror Assembly (HRMA) X-ray Detection System (HXDS) stage dithers, and the five-axis mount (FAM) attachment points underwent various types of motion during testing. At the XRCF when the FAM moved, the Science Instrument Module (SIM) travel direction was not necessarily aligned with the mirror axis motion, and, in addition, an arbitrary position offset had to be calibrated. Misalignment from the mirror axis was assessed by measuring its displacement from the boresight configuration of the default FAM frame, and the HXDS stage was monitored for motion from the default FAM reference point. Mirror position, prescribed in a mirror modal coordinate system, was measured in HRMA pitch and yaw axes. Prior to corrections for dithering and FAM movement, the coordinate data at XRCF also had to be corrected for possible misalignments of the mirror mount relative to XRCF and the default FAM axes due to the movement of the FAM feet. Those misalignments were processed in terms of yaw-pitch-roll Euler angles in the mirror nodal coordinate, and in the default FAM frame, respectively. An AXAF Science Center (ASC) coordinate library, pixlib, has been built to support these coordinate transformations and was used during x-ray calibration at the George C. Marshall Space Flight Center, Huntsville, AL. The design and implementation of this library will be discussed.

He, Helen↗

Spacecraft Attitude Representations

The direction cosine matrix or attitude matrix is the most fundamental representation of the attitude, but it is very inefficient: It has six redundant parameters, it is difficult to enforce the six (orthogonality) constraints. the four-component quaternion representation is very convenient: it has only one redundant parameter, it is easy to enforce the normalization constraint, the attitude matrix is a homogeneous quadratic function of q, quaternion kinematics are bilinear in q and m. Euler angles are extensively used: they often have a physical interpretation, they provide a natural description of some spacecraft motions (COBE, MAP), but kinematics and attitude matrix involve trigonometric functions, "gimbal lock" for certain values of the angles. Other minimum (three-parameter) representations: Gibbs vector is infinite for 180 deg rotations, but useful for analysis, Modified Rodrigues Parameters are nonsingular, no trig functions, Rotation vector phi is nonsingular, but requires trig functions.

Markley, F. Landis↗

Modeling the Launch Abort Vehicle's Subsonic Aerodynamics from Free Flight Testing

An investigation into the aerodynamics of the Launch Abort Vehicle for NASA's Constellation Crew Launch Vehicle in the subsonic, incompressible flow regime was conducted in the NASA Langley 20-ft Vertical Spin Tunnel. Time histories of center of mass position and Euler Angles are captured using photogrammetry. Time histories of the wind tunnel's airspeed and dynamic pressure are recorded as well. The primary objective of the investigation is to determine models for the aerodynamic yaw and pitch moments that provide insight into the static and dynamic stability of the vehicle. System IDentification Programs for AirCraft (SIDPAC) is used to determine the aerodynamic model structure and estimate model parameters. Aerodynamic models for the aerodynamic body Y and Z force coefficients, and the pitching and yawing moment coefficients were identified.

Hartman, Christopher L.↗

Output Measurement Equations for Flexible Aircraft Flight Dynamics

A summary of output measurement equations for onboard sensors used in flight testing of flexible aircraft is presented. These equations include the effects of structural flexibility and are considerably more complex than the standard equations for rigid-body aircraft. The output equations discussed include accelerations from linear accelerometers, strains, angular rates, angular accelerations, Euler angles, true airspeed, and air flow angles. The output equations are derived in full form and then simplified in some cases. Linearized output equations, suitable for state-space or transfer function models, are also developed. Example flight test data from the X-56A subscale aeroelastic demonstrator is discussed, for reference.

Grauer, Jared A.↗

Method for Approximating the Vacuum Motions of Spinning Symmetrical Bodies with Nonconstant Spin Rates

The analysis includes non-constant spin rates and inertias and considers the effects of time-varying thrust misalignments, mass unbalance, and jet damping. The method was developed for bodies having small trans verse angular velocities. Results are presented in the form of equations for space-referenced Euler angles, flight-path angles, body-referenced attitude rates, and earth-referenced vehicle-trajectory coordinates. Also, equations for maximum wobble have been derived for certain input conditions. Comparisons with numerical solutions are included for two sample problems.

Martz, C. William↗