Search NASA⌕ Search

SEARCH · Search NASA

Results for “FIGHTER AIRCRAFT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Results of piloted simulator studies of fighter aircraft at high angles of attack

The experience gained at the NASA Langley Research Center during the application of simulator techniques to high angle of attack flight conditions for several current fighters is discussed. The discussion includes (1) the simulator hardware, (2) requirements for static and dynamic aerodynamic data inputs, (3) evaluation procedures, (4) correlation with flight, and (5) the effects of dynamic stability parameters. Results obtained with the simulator technique have correlated well with flight test experience, resulting in early identification of potential problems, identification of critical flight conditions, and solutions to various deficiencies in stability and control characteristics. Dynamic stability parameters, results indicate that certain parameters can have a large influence on the flying qualities and tactical effectiveness of fighters at high angles of attack.

Chambers, J. R.↗
NASA NTRS1984

Interference effects of thrust reversing on horizontal tail effectiveness of twin-engine fighter aircraft at Mach numbers from 0.15 to 0.90

An investigation was conducted in the Langley 16 foot Transonic Tunnel to determine the interference effects of thrust reversing on horizontal tail effectiveness of a twin engine, general research fighter model at approach and in-flight speeds. Twin vertical tails at three longitudinal locations were tested at a cant angle of 0 deg. One configuration was also tested at a cant angle of 20 deg. Two nonaxisymmetric nozzle reverser concepts were studied. Test data were obtained at Mach numbers of 0.15, 0.60, and 0.90 and at angles of attack from -3 to 9 deg. Nozzle pressure ratios varied from jet off to 7.0, depending upon Mach number. At landing approach speed (Mach number 0.15), thrust reverser operation usually resulted in large variations (up to 70% increase) in horizontal tail effectiveness as nozzle pressure ratio was varied at zero angle of attack or as angle of attack was varied at constant nozzle pressure ratio. There was always a decrease in effectiveness at Mach numbers of 0.60 and 0.90 as a result of reverser operation.

Capone, F. J.↗
NASA NTRS1979

Evaluation of turbo-propulsion simulators as a testing technique for fighter aircraft

Ames Research Center has under way a program to develop the technology for using turbine-powered jet engine simulators as a test technique for simulating installed jet engine characteristics in small-scale wind-tunnel models of complete VSTOL fighter configurations. The program consists of three key elements: (1) static testing SN003 prototype turbine engine simulator (MAPS), (2) the development of the Propulsion Simulator Calibration Laboratory at Ames, and (3) the design, fabrication, and testing of a twin-engine 'closely coupled' V/STOL fighter wind-tunnel model. The model will use the Compact Multi-mission Propulsion Simulator (CMAPS) and will also be tested in flow-through and jet-effects modes to assess the effect of simultaneous inlet and nozzle flow simulation. This paper includes a description of the planned effort and anticipated future tasks.

Bailey, R. O.↗
NASA NTRS1985

Rotary-balance experiments on a modern fighter aircraft configuration at high Reynolds numbers

NASA Ames Research Center's research program to investigate high-angle-of-attack aerodynamic phenomena associated with high-performance aircraft includes the development and use of rotary balance apparatuses for wind balance apparatuses for wind tunnel tests of airplane models in a coning motion. A large scale apparatus, developed for testing models at high Reynolds numbers in the Ames 12-Foot Pressure Wind Tunnel, was recently tested with an 0.05-scale F-15 fighter model. Measurements were made at low subsonic Mach numbers and chord Reynolds numbers of 1 to 5.5 million, with angles of attack from 0 to 90 deg and sideslip angles from -15 to +15 deg. Effects of Reynolds number, spin-rate parameter, model attitude, presence of a nose boom, and model/sting mounting angle were investigated.

Malcolm, G. N.↗
NASA NTRS1991

Aerodynamic control of fighter aircraft by manipulation of forebody vortices

Methods of enhancing aircraft controllability and maneuverability at high angles of attack by manipulating the forebody vortices are discussed. Pneumatic control methods including jet blowing, slot blowing, and suction, and mechanical control methods using forebody and nose tip strakes are reviewed. The potential of various control devices in controlling the forebody flow, and thus, providing controlled yawing moments at high angles of attack are illustrated using wind tunnel results from a generic fighter and water tunnel results from an F/A-18.

Malcolm, Gerald N.↗
NASA NTRS1975

Compatibility of take-off and landing with mission and manoeuvre performance requirements for fighter aircraft

By means of an aircraft synthesis program, the effect of engine cycle, thrust to weight ratio, and wing parameter combination on field and flight performance has been investigated. For three different engine/intake configurations, thrust to weight ration and wing loading were varied. Each combination represents an aircraft designed to meet a specified mission radius. Using different lift systems and ground deceleration devices, the conditions are shown under which a matching of flight and field performance is economically feasible.

Reich, D.↗
NASA NTRS1980

Flow Visualization Study of the F-14 Fighter Aircraft Configuration

Water tunnel studies were performed to qualitatively define the flow field of the F-14. Particular emphasis was placed on defining the vortex flows generated at high angles of attack. The flow visualization tests were conducted in the Northrop water tunnel using a 1/72 scale model of the F-14 with a wing leading-edge sweep of 20 deg. Flow visualization photographs were obtained for angles of attack up to 55 deg and sideslip angles up to 10 deg. The F-14 model was investigated to determine the vortex flow field development, vortex path, and vortex breakdown characteristics as a function of angle of attack and sideslip. Vortex flows were found to develop on the highly swept glove and on the upper surface of the forebody. At 10 deg of sideslip, the windward glove vortex shifted inboard and broke down farther forward than the leeward glove vortex. This asymmetric breakdown of the vortices in sideslip contributes to a reduction in the lateral stability above 20 deg angle of attack. The initial loss of directional stability is a consequence of the adverse sidewash from the windward vortex and the reduced dynamic pressure at the vertical tails.

Lorincz, D. J.↗
NASA NTRS1981

A computer technique for detailed analysis of mission radius and maneuverability characteristics of fighter aircraft

A computer technique to determine the mission radius and maneuverability characteristics of combat aircraft was developed. The technique was used to determine critical operational requirements and the areas in which research programs would be expected to yield the most beneficial results. In turn, the results of research efforts were evaluated in terms of aircraft performance on selected mission segments and for complete mission profiles. Extensive use of the technique in evaluation studies indicates that the calculated performance is essentially the same as that obtained by the proprietary programs in use throughout the aircraft industry.

Foss, W. E., Jr.↗
NASA NTRS1980

Flow visualization study of spanwise blowing applied to the F-4 fighter aircraft configuration

Water tunnel studies were performed to define the changes that occur in vortex flow fields above the wing due to spanwise blowing over the inboard and outboard wing panels and over the trailing-edge flaps. Flow visualization photographs were obtained for angles of attack up to 30 deg and sideslip angles up to 10 deg. The sensitivity of the vortex flows to changes in flap deflection angle, nozzle position, and jet momentum coefficient was determined. Deflection of the leading edge flap delayed flow separation and the formation of the wing vortex to higher angles of attack. Spanwise blowing delayed the breakdown of the wing vortex to farther outboard and to higher angles of attack. Spanwise blowing over the trailing edge flap entrained flow downward, producing a lift increase over a wide range of angles of attack. The sweep angle of the windward wing was effectively reduced in sideslip. This decreased the stability of the wing vortex, and it burst farther inboard. Reduced wing sweep required a higher blowing rate to maintain a stable vortex. A vortex could be stabilized on the outboard wing panel when an outboard blowing nozzle was used. Blowing from both an inboard and an outboard nozzle was found to have a favorable interaction.

Lorincz, D. J.↗
NASA NTRS1984

The Mission Radius and Maneuverability Characteristics of Fighter Aircraft

Computer program provides detailed analysis of mission radius and maneuverability characteristics of combat aircraft. Program combination of five mission modules representing mission profiles currently of interest. Each mission Module designed to determine combat radius or range capability for specific mission with associated ground rules and profile definitions.

Foss, W. E.., Jr.↗
NASA NTRS1983

Empennage/afterbody integration for single and twin-engine fighter aircraft

An extensive experimental program to determine the effects of empennage surfaces on single and twin-engine afterbody/nozzle drag has been conducted by the Propulsion Aerodynamics Branch at the NASA Langley Research Center. Empennage interference drag was obtained by using experimental values of afterbody/nozzle drag and computed values of empennage drag. The effects of tail location, span, number (single versus twin), toe angle, cant angle, camber and root chord length are discussed. The magnitude of empennage interference drag on single and twin engine configurations is examined.

Berrier, B. L.↗
NASA NTRS1984

A study of prediction methods for the high angle-of-attack aerodynamics of straight wings and fighter aircraft

Work is described dealing with two areas which are dominated by the nonlinear effects of vortex flows. The first area concerns the stall/spin characteristics of a general aviation wing with a modified leading edge. The second area concerns the high-angle-of-attack characteristics of high performance military aircraft. For each area, the governing phenomena are described as identified with the aid of existing experimental data. Existing analytical methods are reviewed, and the most promising method for each area used to perform some preliminary calculations. Based on these results, the strengths and weaknesses of the methods are defined, and research programs recommended to improve the methods as a result of better understanding of the flow mechanisms involved.

Mcmillan, O. J.↗
NASA NTRS1984

Assessment of aerodynamic performance of V/STOL and STOVL fighter aircraft

The aerodynamic performance of V/STOL and STOVL fighter/attack aircraft was assessed. Aerodynamic and propulsion/airframe integration activities are described and small and large scale research programs are considered. Uncertainties affecting aerodynamic performance that are associated with special configuration features resulting from the V/STOL requirement are addressed. Example uncertainties relate to minimum drag, wave drag, high angle of attack characteristics, and power induced effects.

Nelms, W. P.↗
NASA NTRS1985

Computer sizing of fighter aircraft

The computer sizing technique has been applied to a number of military mission profiles. Performance data can be determined for all segments of the selected profile, which typically include takeoff, climb, cruise, loiter, reserve and landing segments. Options are available for detailed calculation of combat performance and energy-maneuverability characteristics. Configuration changes, such as external fuel tank drop and weapon expenditure, can be included in the mission. In the sizing mode, aircraft gross weight, wing loading, and thrust-to-weight ratio are varied automatically to determine which combinations meet the design mission radius. The resulting performance data can be used to create a thumbprint plot. This plot is useful in determining the configuration size that best satisfies the mission and performance requirements. The sizing mode can also be used to perform parametric studies such as sensitivity of gross weight to alternate design conditions.

Coen, P. G.↗
NASA NTRS1986

Computer sizing of fighter aircraft

The computer sizing technique has been applied to a number of military mission profiles. Performance data can be determined for all segments of the selected profile, which typically include takeoff, climb, cruise, loiter, reserve and landing segments. Options are available for detailed calculation of combat performance and energy-maneuverability characteristics. Configuration changes, such as external fuel tank drop and weapon expenditure, can be included in the mission. In the sizing mode, aircraft gross weight, wing loading, and thrust-to-weight ratio are varied automatically to determine which combinations meet the design mission radius. The resulting performance data can be used to create a thumbprint plot. This plot is useful in determining the configuration size that best satisfies the mission and performance requirements. The sizing mode can also be used to perform parametric studies such as sensitivity of gross weight to alternate design conditions.

Coen, P. G.↗
NASA NTRS1984

Flutter optimization in fighter aircraft design

The efficient design of aircraft structure involves a series of compromises among various engineering disciplines. These compromises are necessary to ensure the best overall design. To effectively reconcile the various technical constraints requires a number of design iterations, with the accompanying long elapsed time. Automated procedures can reduce the elapsed time, improve productivity and hold the promise of optimum designs which may be missed by batch processing. Several examples are given of optimization applications including aeroelastic constraints. Particular attention is given to the success or failure of each example and the lessons learned. The specific applications are shown. The final two applications were made recently.

Triplett, W. E.↗
NASA NTRS1989

Application of Artificial Intelligence (AI) programming techniques to tactical guidance for fighter aircraft

A research program investigating the use of Artificial Intelligence (AI) programming techniques to aid in the development of a Tactical Decision Generator (TDG) for Within-Visual-Range (WVR) air combat engagements is discussed. The application of AI methods for development and implementation of the TDG is presented. The history of the Adaptive Maneuvering Logic (AML) program is traced and current versions of the (AML) program is traced and current versions of the AML program are compared and contrasted with the TDG system. The Knowledge-Based Systems (KBS) used by the TDG to aid in the decision-making process are outlined and example rules are presented. The results of tests to evaluate the performance of the TDG against a version of AML and against human pilots in the Langley Differential Maneuvering Simulator (DMS) are presented. To date, these results have shown significant performance gains in one-versus-one air combat engagements.

Mcmanus, John W.↗