SEARCH · Search NASA

Results for “FLOW - AIRFOILS - CASCADES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS2024

Measurements and Computational Analysis of the Turbulent Corner Flow on the NASA Juncture-Flow Model with a Symmetric Wing

The NASA Juncture Flow Experiment is designed to acquire high-quality flowfield data deep in the corner of a wing-fuselage junction for the purpose of computational fluid dynamics (CFD) validation and turbulence model improvement. This report presents and discusses the results of a recent experiment with the Juncture Flow Model in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The main objective of the test was to expand the existing juncture-flow dataset with a symmetric wing case that displays fully attached, incipient separation, and separated flow in the corner of the wing-fuselage junction, depending on the model angle of incidence. Laser Doppler velocimetry (LDV) measurements were made at three model angles of incidence (0° : fully attached, 1° : incipient separation, and 5° : separated flow) and for each angle, mean-flow and Reynolds-stress data were obtained on the fuselage and at several locations along the corner of the wing-fuselage junction. Supporting measurements were made during the test campaign and include model and tunnel wall static pressures, tunnel wall boundary-layer profiles, oil-flow visualizations, and laser-based measurements of the as-built model geometry and model position in the test section. A companion set of Reynolds-averaged Navier-Stokes (RANS) CFD simulations were also performed and those results were used to support the discussion of the experimental test results.

Juncture Flow↗

NASA NTRS1973

FORTRAN program for calculating velocities and streamlines on the hub-shroud mid-channel flow surface of an axial- or mixed-flow turbomachine. 1: User's manual

A FORTRAN 4 computer program has been developed that obtains a subsonic or shock-free transonic flow solution on the hub-shroud mid-channel flow surface of a turbomachine. The blade row may be fixed or rotating, and may be twisted and leaned. Flow may be axial or mixed, up to 45 deg from axial. Upstream and downstream flow variables may vary from hub to shroud, and provision is made to correct for loss of stagnation pressure. The results include velocities, streamlines, and flow angles on the flow surface; and approximate blade surface velocities. Subsonic solutions are obtained by a finite-difference stream-function solution. Transonic solutions are obtained by a velocity-gradient method, using information from a finite-difference stream-function solution at a reduced mass flow.

Katsanis, T.↗

NASA NTRS1974

FORTRAN program for calculating velocities and streamlines on the hub-shroud mid-channel flow surface of an axial-or mixed-flow turbomachine. 2: Programmer's manual

A FORTRAN-IV computer program, MERIDL, has been developed that obtains a subsonic or shock-free transonic flow solution on the hub-shroud mid-channel flow surface of a turbomachine. The blade row may be fixed or rotating and may be twisted and leaned. Flow may be axial or mixed, up to 45 deg from axial. Upstream and downstream flow variables can vary from hub to shroud, and provision is made to correct for loss of stagnation pressure. The results include velocities, streamlines, and flow angles on the flow surface and approximate blade surface velocities. Subsonic solutions are obtained by a finite-difference stream-function solution. Transonic solutions are obtained by a velocity-gradient method, using information from a finite-difference stream-function solution at a reduced mass flow.

Katsanis, T.↗

NASA NTRS1975

Three dimensional flow field in rocket pump inducers. Part 2: Mean flow and turbulence characteristics inside the rotor passage, and theoretical analysis

The measurement and prediction is reported of three dimensional flow fields in an axial flow inducer operating at a flow coefficient of 0.065 with air as the test medium. The experimental investigations included measurements of the blade static pressure and blade limiting streamline angle, and measurement of the three components of mean velocity, turbulence intensities and turbulence stresses at locations inside the inducer blade passage utilizing a rotating three-sensor hotwire probe. Analytical investigations were conducted to predict the three-dimensional inviscid flow. Total relative velocity distributions indicate a substantial velocity deficiency near the tip at mid-passage. High turbulence intensities and turbulence stresses are concentrated within this core region. Evidence of boundary layer interactions, blade blockage effects, radially inward flows, annulus wall effects and backflows are found to exist within the long, narrow passages of the inducer, emphasizing the complex nature of inducer flow which makes accurate prediction of the flow behavior extremely difficult.

Lakshminarayana, B.↗

NASA NTRS1982

Flow structure in continuous flow electrophoresis chambers

There are at least two ways that hydrodynamic processes can limit continiuous flow electrophoresis. One arises from the sensitivity of the flow to small temerature gradients, especially at low flow rates and power levels. This sensitivity can be suppressed, at least in principle, by providing a carefully tailored, stabilizing temperature gradient in the cooling system that surrounds the flow channel. At higher power levels another limitation arises due to a restructuring of the main flow. This restructuring is caused by buoyancy, which is in turn affected by the electro-osmotic crossflow. Approximate solutions to appropriate partial differential equations have been computed by finite difference methods. One set of results is described here to illustrate the strong coupling between the structure of the main (axial) flow and the electro-osmotic flow.

Deiber, J. A.↗

NASA NTRS1987

A critical evaluation of various methods for the analysis of flow-solid interaction in a nest of thin cylinders subjected to cross flows

Various experimental, analytical, and numerical analysis methods for flow-solid interaction of a nest of cylinders subjected to cross flows are reviewed. A nest of cylinders subjected to cross flows can be found in numerous engineering applications including the Space Shuttle Maine Engine-Main Injector Assembly (SSME-MIA) and nuclear reactor heat exchangers. Despite its extreme importance in engineering applications, understanding of the flow-solid interaction process is quite limited and design of the tube banks are mostly dependent on experiments and/or experimental correlation equations. For future development of major numerical analysis methods for the flow-solid interaction of a nest of cylinders subjected to cross flow, various turbulence models, nonlinear structural dynamics, and existing laminar flow-solid interaction analysis methods are included.

Kim, Sang-Wook↗

NASA NTRS1988

A review of various flow-solid interaction analysis methods with emphasis on recent advances in turbulence models and flow analysis methods

A review on various experimental, analytical, and numerical methods for the flow-solid interaction of a nest of cylinders subjected to cross flow is presented in this paper. In order to assess the possibility of initiating a development of major numerical analysis method for flow-solid interaction of a nest of cylinders in cross flows, a review on various turbulence models, numerical methods such as the finite element method and the finite difference method, and the available numerical methods for flow-solid interactions have been included in this paper. A multiple-time-scale turbulence model for complex turbulent flows and a finite element method for high Reynolds number flows have been introduced herein for the same reason.

Kim, S.-W.↗

NASA NTRS1991

Flow visualization and flow field measurements of a 1/12 scale tilt rotor aircraft in hover

The results are given of flow visualization studies and inflow velocity field measurements performed on a 1/12 scale model of the XV-15 tilt rotor aircraft in the hover mode. The complex recirculating flow due to the rotor-wake-body interactions characteristic of tilt rotors was studied visually using neutrally buoyant soap bubbles and quantitatively using hot wire anemometry. Still and video photography were used to record the flow patterns. Analysis of the photos and video provided information on the physical dimensions of the recirculating fountain flow and on details of the flow including the relative unsteadiness and turbulence characteristics of the flow. Recirculating flows were also observed along the length of the fuselage. Hot wire anemometry results indicate that the wing under the rotor acts to obstruct the inflow causing a deficit in the inflow velocities over the inboard region of the model. Hot wire anemometry also shows that the turbulence intensities in the inflow are much higher in the recirculating fountain reingestion zone.

Coffen, Charles D.↗

NASA NTRS1993

The ground vortex flow field associated with a jet in a cross flow impinging on a ground plane for uniform and annular turbulent axisymmetric jets

An experimental study was conducted of the impingement of a single circular jet on a ground plane in a cross flow. This geometry is a simplified model of the interaction of propulsive jet exhaust from a V/STOL aircraft with the ground in forward flight. Jets were oriented normal to the cross flow and ground plane. Jet size, cross flow-to-jet velocity ratio, ground plane-to-jet board spacing, and jet exit turbulence level and mean velocity profile shape were all varied to determine their effects on the size of the ground vortex interaction region which forms on the ground plane, using smoke injection into the jet. Three component laser Doppler velocimeter measurements were made with a commercial three color system for the case of a uniform jet with exit spacing equal to 5.5 diameters and cross flow-to-jet velocity ratio equal to 0.11. The flow visualization data compared well for equivalent runs of the same nondimensional jet exit spacing and the same velocity ratio for different diameter nozzles, except at very low velocity ratios and for the larger nozzle, where tunnel blockage became significant. Variation of observed ground vortex size with cross flow-to-jet velocity ratio was consistent with previous studies. Observed effects of jet size and ground plane-to-jet board spacing were relatively small. Jet exit turbulence level effects were also small. However, an annular jet with a low velocity central core was found to have a significantly smaller ground vortex than an equivalent uniform jet at the same values of cross flow-to-jet velocity ratio and jet exit-to-ground plane spacing. This may suggest a means of altering ground vortex behavior somewhat, and points out the importance of proper simulation of jet exit velocity conditions. LV data indicated unsteady turbulence levels in the ground vortex in excess of 70 percent.

Cavage, William M.↗

NASA NTRS1992

Aeroloads and secondary flows in a transonic mixed flow turbine stage

A numerical simulation of a transonic mixed flow turbine stage has been carried out using an average passage Navier-Stokes analysis. The mixed flow turbine stage considered here consists of a transonic nozzle vane and a highly loaded rotor. The simulation was run at the design pressure ratio and is assessed by comparing results with those of an established throughflow design system. The three-dimensional aerodynamic loads are studied as well as the development and migration of secondary flows and their contribution to the total pressure loss. The numerical results indicate that strong passage vortices develop in the nozzle vane, mix out quickly, and have little impact on the rotor flow. The rotor is highly loaded near the leading edge. Within the rotor passage, strong spanwise flows and other secondary flows exist along with the tip leakage vortex. The rotor exit loss distribution is similar in character to that found in radial inflow turbines. The secondary flows and non-uniform work extraction also tend to significantly redistribute a non-uniform inlet total temperature profile by the exit of the stage.

Kirtley, K. R.↗

NASA NTRS1991

Flow visualization and flow field measurements of a 1/12 scale tilt rotor aircraft in hover

Coffen, Charles D.↗

NASA NTRS1949

Two-dimensional compressible flow in turbomachines with conic flow surfaces

A general method of analysis is developed for two-dimensional, steady, compressible flow in stators or rotors of radial and mixed flow turbomachines with conic flow surfaces (surfaces of right circular cones generated by center line of flow passage in the axial-radial plane). The variables taken into account are: (1) tip speed of the rotor, (2) flow rate, (3) blade shape, (4) variation in passage height with radius, (5) number of blades, and (6) cone angle of the flow surface. Relaxation methods are used to solve the nonlinear differential equation for the stream function. Two numerical examples are presented; one for compressible and the other for incompressible flow in a centrifugal compressor with thin, straight blades. The results of these examples are given by plots of the streamlines, constant velocity-ratio lines, and constant pressure-ratio line.

Stanitz, John D↗

NASA NTRS1996

Experimental Investigation of the Flow Field in a Transonic, Axial Flow Compressor with Respect to the Development of Blockage and Loss

A detailed experimental investigation to understand and quantify the development of loss and blockage in the flow field of a transonic, axial flow compressor rotor has been undertaken. Detailed laser anemometer measurements were acquired upstream, within, and downstream of a transonic, axial compressor rotor operating at design and off-design conditions. The rotor was operated at 100%, 85%, 80%, and 60% of design speed which provided inlet relative Mach numbers at the blade tip of 1.48, 1.26, 1.18, and 0.89 respectively. At design speed the blockage is evaluated ahead of the rotor passage shock, downstream of the rotor passage shock, and near the trailing edge of the blade row. The blockage is evaluated in the core flow area as well as in the casing endwall region. Similarly at pm speed conditions for the cases of (1) where the rotor passage shock is much weaker than that at design speed and (2) where there is no rotor passage shock, the blockage and loss are evaluated and compared to the results at design speed. Specifically, the impact of the rotor passage shock on the blockage and loss development, pertaining to both the shock/boundary layer interactions and the shock/tip clearance flow interactions, is discussed. In addition, the blockage evaluated from the experimental data is compared to (1) an existing correlation of blockage development which was based on computational results, and (2) computational results on a limited basis. The results indicate that for this rotor the blockage in the endwall region is 2-3 times that of the core flow region and the blockage in the core flow region more than doubles when the shock strength is sufficient to separate the suction surface boundary layer. The distribution of losses in the care flow region indicate that the total loss is primarily comprised of the shock loss when the shock strength is not sufficient to separate the suction surface boundary layer. However, when the shock strength is sufficient to separate the suction surface boundary layer, the profile loss is comparable to the shock loss and can exceed the shock loss.

Suder, Kenneth L.↗

NASA NTRS1959

Heat Transfer from Cylinders in Transition From Slip Flow to Free-Molecule Flow

Over 600 measured heat-transfer coefficients in the transition from slip to free-molecule flow have been correlated by using the Nusselt number Nu as a function of the Knudsen Kn and Reynolds Re (or Mach M) numbers. The experimental range for these heat-transfer data from transverse cylinders in air corresponds to the following dimensionless groups: M, 0.10 to 0.90; Re, 0.03 to 11.5; Kn, 0.10 to 5.0. The total air temperature T(sub t) was maintained constant at 80 F, but wire temperature was Varied from 150 to 580 F. At Kn=0.10, Nu extrapolates smoothly into slip-flow empirical curves that show Nu as a function of Re and M or Kn. The correlation gradually changes from the square root of Re(sub t) dependence characteristic of continuum flow to first-power Re dependence as Kn increases (decreasing Re). At the experimental limit Kn ft 5.0, the Nu data correlate with a mean fractional error of 413 percent by the prediction of free-molecule-flow theory. In comparing experimental results with theory, an accommodation coefficient of 0.57+/-0.07 was inferred from the heat-transfer data, which were obtained with etched tungsten wire in air. The wire recovery temperature T(sub e) was measured and compared with existing data and theory in terms of a ratio eta(equivalent to T(sub e)/T(sub t). The results can be divided into three groups by Kn criteria: For Kn less than 2.01, eta is independent of Kn, and eta decreases from 1.0 to 0.97 as M increases from 0 to 0.90; for 2.0 less than Kn less than 5.0, eta is a function of both Kn and M in this transition region to fully developed free-molecule flow; and for Kn greater than 5.0, eta predicted by free-molecule-flow theory is observed and increases from 1.0 to 1.08 as M increases from 0 to 0.90, again independent of Kn. Therefore, these T(sub e) data provide a guide to the boundary of fully developed free-molecule flow, which is.inferred from this research to exist for Kn greater than 5.0. This boundary criterion is substantiated by other published data on T(sub e) at supersonic speeds.

Cybulski, Ronald J.↗

NASA NTRS2002

The Steady Flow Resistance of Perforated Sheet Materials in High Speed Grazing Flows

A study was conducted to determine the effects of high speed grazing air flow on the acoustic resistance of perforated sheet materials used in the construction of acoustically absorptive liners placed in commercial aircraft engine nacelles. Since DC flow resistance of porous sheet materials is known to be a major component of the acoustic resistance of sound suppression liners, the DC flow resistance of a set of perforated face-sheets and linear 'wiremesh' face-sheets was measured in a flow duct apparatus (up to Mach 0.8). Samples were fabricated to cover typical variations in perforated face-sheet parameters, such as hole diameter, porosity and sheet thickness, as well as those due to different manufacturing processes. The DC flow resistance data from perforated sheets were found to correlate strongly with the grazing flow Mach number and the face-sheet porosity. The data also show correlation against the boundary layer displacement thickness to hole-diameter ratio. The increase in resistance with grazing flow for punched aluminum sheets is in good agreement with published results up to Mach 0.4, but is significantly larger than expected above Mach 0.4. Finally, the tests demonstrated that there is a significant increase in the resistance of linear 'wiremesh' type face-sheet materials.

Syed, Asif A.↗

NASA NTRS2006

Two Phase Flow Modeling: Summary of Flow Regimes and Pressure Drop Correlations in Reduced and Partial Gravity

The purpose of this report is to provide a summary of state-of-the-art predictions for two-phase flows relevant to Advanced Life Support. We strive to pick out the most used and accepted models for pressure drop and flow regime predictions. The main focus is to identify gaps in predictive capabilities in partial gravity for Lunar and Martian applications. Following a summary of flow regimes and pressure drop correlations for terrestrial and zero gravity, we analyze the fully developed annular gas-liquid flow in a straight cylindrical tube. This flow is amenable to analytical closed form solutions for the flow field and heat transfer. These solutions, valid for partial gravity as well, may be used as baselines and guides to compare experimental measurements. The flow regimes likely to be encountered in the water recovery equipment currently under consideration for space applications are provided in an appendix.

Balasubramaniam, R.↗

NASA NTRS2011

Inflation Features of the Distal Pahoehoe Portion of the 1859 Mauna Loa Flow, Hawaii; Implications for Evaluating Planetary Lava Flows

The 1859 eruption of Mauna Loa, Hawaii, resulted in the longest subaerial lava flow on the Big Island. Detailed descriptions were made of the eruption both from ships and following hikes by groups of observers; the first three weeks of the eruption produced an `a`a flow that reached the ocean, and the following 10 months produced a pahoehoe flow that also eventually reached the ocean. The distal portion of the 1859 pahoehoe flow component includes many distinctive features indicative of flow inflation. Field work was conducted on the distal 1859 pahoehoe flow during 2/09 and 3/10, which allowed us to document several inflation features, in or-der evaluate how well inflated landforms might be detected in remote sensing data of lava flows on other planets.

Zimbelman, J. R.↗

NASA NTRS2015

Flow Diode and Method for Controlling Fluid Flow Origin of the Invention

A flow diode configured to permit fluid flow in a first direction while preventing fluid flow in a second direction opposite the first direction is disclosed. The flow diode prevents fluid flow without use of mechanical closures or moving parts. The flow diode utilizes a bypass flowline whereby all fluid flow in the second direction moves into the bypass flowline having a plurality of tortuous portions providing high fluidic resistance. The portions decrease in diameter such that debris in the fluid is trapped. As fluid only travels in one direction through the portions, the debris remains trapped in the portions.

Dyson, Rodger W↗