Search NASA⌕ Search

SEARCH · Search NASA

Results for “FPS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

High-Tip-Speed, Low-Loading Transonic Fan Stage. Part 1: Aerodynamic and Mechanical Design

A high-tip-speed, low-loading transonic fan stage was designed to deliver an overall pressure ratio of 1.5 with an adiabatic efficiency of 86 percent. The design flow per unit annulus area is 42.0 pounds per square foot. The fan features a hub/tip ratio of 0.46, a tip diameter of 28.74 in. and operates at a design tip speed of 1600 fps. For these design conditions, the rotor blade tip region operates with supersonic inlet and supersonic discharge relative velocities. A sophisticated quasi-three-dimensional characteristic section design procedure was used for the all-supersonic sections and the inlet of the midspan transonic sections. For regions where the relative outlet velocities are supersonic, the blade operates with weak oblique shocks only.

Wright, L. C.↗
NASA NTRS1973

An analytical investigation of acquisition techniques and system integration studies for a radar aircraft guidance research facility, phase 2

A review of user requirements and updated instrumentation plans are presented for the aircraft tracking and guidance facility at NASA Wallops Station. User demand has increased as a result of new flight research programs; however, basic requirements remain the same as originally reported. Instrumentation plans remain essentially the same but with plans for up- and down-link telemetry more firm. With slippages in the laser acquisition schedule, added importance is placed on the FPS-16 radar as the primary tracking device until the laser is available. Limited simulation studies of a particular Kalman-type filter are also presented. These studies simulated the use of the filter in a helicopter guidance loop in a real-time mode. Disadvantages and limitations of this mode of operation are pointed out. Laser eyesafety calculations show that laser tracking of aircraft is readily feasible from the eyesafety viewpoint.

Thompson, W. S.↗
NASA NTRS1973

High resolution system for upper air (troposphere) wind and temperature profile measurements

The Jimsphere/Jimsonde system is described and some possible applications of the system for air-sea interface measurements are presented. As space vehicles became larger and more sophisticated, an improved method for obtaining wind profile data had to be found. To satisfy this need the FPS-16 radar/Jimsphere system was developed. The Jimsphere is an aluminized mylar spherical balloon, two meters in diameter. The balloon is under superpressure, and is tracked with a high precision radar system. The development of this detailed wind profile system was started in 1963, and the present design was established in 1964. To improve the system, a program was initiated in 1965 to obtain high resolution temperature data simultaneously with the wind profile data.

Camp, D. W.↗
NASA NTRS1973

A multi-sensor analysis of Nimbus 5 data on 22 January 1973

The Nimbus 5 meteorological satellite carried aloft a full complement of radiation sensors, the data from which were analyzed and intercompared during orbits 569-570 on 22 January 1973. The electrically scanning microwave radiometer (ESMR) which sensed passive microwave radiation in the 19.35 GHz region, delineated rain areas over the ocean off the U.S. east coast, in good agreement with WSR-57 and FPS-77 radar imagery and permitted the estimation of rainfall rates in this region. Residual ground water in the lower Mississippi Valley, which resulted from abnormal rainfall in previous months, was indicated under clear sky conditions by soil brightness temperature values in the Nimbus 5 ESMR and U.S. Air Force Data Acquisition and Processing Program (DAPP) IR data. The temperature-humidity infrared radiometer showed the height and spatial configuration of frontal clouds along the east coast and outlined the confluence of a polar jet stream with a broad sub-tropical jet stream along the U.S. Gulf Coast. Temperature profiles from three vertical temperature sounders, the infrared temperature profile radiometer (ITPR), the Nimbus E microwave spectrometer (NEMS) and the selective chopper radiometer (SCR) were found to be in good agreement with related radiosonde ascents along orbit 569 from the sub-tropics to the Arctic Circle.

Allison, L. J.↗
NASA NTRS1974

Study of a flight monitor for jet engine disk cracks using the critical length criterion of fracture mechanics

A disk crack detector is discussed which is intended to operate while in flight. The crack detector monitors the disk rim for radial surface cracks emanating from the blade root interface. An eddy current type sensor with a remotely located capacitance-resistance bridge and signal analyzer is able to detect reliably a simulated crack 1/8 in. long. The sensor was tested at rim velocities of 600 fps and at 1000 F. Fracture mechanics is used to calculate the critical crack length. Knowledge of the crack growth rate permits the calculation of the number of stress cycles remaining for the detected crack to grow to critical size. A plot is presented of the remaining life as a function of the critical crack length and the operating stress. It is shown that for a disk of Inconel 718 a through-the-thickness crack operating under a rim stress of 50 kpsi has a critical length of 0.7-in. and a remaining life of 130 flights.

Barranger, J. P.↗
NASA NTRS1975

Effects of 1980 technology on weight of a recovery system for a one million pound booster

The effects were evaluated of 1980 technology on the weight of recovery systems capable of decelerating a one-million-pound booster to vertical velocities of 60 or 30 ft/sec at sea level impact. A nominal set of booster staging conditions were assumed and there were no constraints on parachute size, number or type. The effects of new materials that would be available by 1980, the effects of booster attitude during entry, various parachute staging methods, parachute reefing schemes, parachute-retro rocket hybrid systems, and the effects of dividing the booster into separate pieces for recovery were evaluated. It was determined that for the systems considered, a hybrid parachute-retro-rocket recovery system would have the minimum weight. New materials now becoming available for parachute fabrication should result in a 37-percent reduction in hybrid recovery system weight for an impact velocity of 30 fps.

Eckstrom, C. V.↗
NASA NTRS1975

High-resolution system for tropospheric wind and temperature profile measurements

This paper briefly describes the Jimsphere/Jimsonde system and presents some possible applications of the system. As space vehicles became larger and more sophisticated, an improved method for obtaining wind-profile data had to be found. To satisfy this need, the FPS-16 radar/Jimsphere system was developed. The Jimsphere is an aluminized mylar spherical balloon 2 m in diameter. The balloon is under superpressure and is tracked with a high-precision radar system. The development of this detailed wind-profile system was started in 1963, and the present design was established in 1964. To improve the system, a program was initiated in 1965 to obtain high-resolution temperature data simultaneously with the wind-profile data.

Camp, D. W.↗
NASA NTRS1975

Post-ejection impacts of the space shuttle solid rocket booster nose cap

The dynamics of impacts between the nose cap ejected from the space shuttle solid rocket booster and the drogue parachute pack are analyzed. The analysis is restricted to planar impact, and assumes the law of restitution and the possible occurrence of three types of impact, depending on the friction behavior of the colliding surfaces: forward slip; backward slip; no slip (normal rebound). The positions of both bodies and their velocities at the time of impact are required. Seven successive impacts, representing all three types, detected and simulated for the case of nose cap ejection at 20 fps normal to the direction of airflow, with selected coefficients of friction (0.25) and restitution (0.85).

Banerjee, A. K.↗
NASA NTRS1975

Circular earth orbits attainable with fixed two-impulse expendable tug

The performance of solid rocket motors in expendable stages as an alternative concept for Shuttle interim upper stage applications is assessed from the standpoint of mission flexibility. The system comprises two stages and a payload, released from a circular Shuttle orbit at 160 naut miles altitude. The stages are sized to deliver a given payload mass to synchronous equatorial orbit. Only nonreturn missions are considered. A parametric sweep was made with small increments of pitch and yaw to compute the possible transfer orbits with an apogee greater than 160 naut miles. At several points on each transfer orbit the possibility of attaining a circular orbit with the second burn impulse of 6000 fps was assessed. Constraints on the vertical component of the second impulse and on the total velocity after firing determine the pitch angle for second burn. Results indicate a fixed two-impulse system designed to place a payload into synchronous equatorial orbit from the Shuttle orbit can deliver the payload mass into any lower circular orbit at any inclination within about 30 deg of the Shuttle orbit. The only apparent disadvantage of the system is an inability to achieve circular orbits above geosynchronous altitudes with the design payload.

Porter, R. F.↗
NASA NTRS1976

Infrared pyrometer for high resolution surface temperature measurements on rotating turbine blades

A high resolution pyrometer was developed and used to obtain temperature profiles of rotating turbine blades at tip speeds up to 366 meters per second (1200 fps). Surface temperature variations from 920 to 1250 K (1200 to 1800 F) can be measured and variations over distances of 0.05 cm (0.020 in.) can be resolved. Temperature profiles were obtained in near real time as hard copies from a computer display terminal. Temperatures measured with the prototype pyrometer and with thermocouples agreed to within 2 percent over the temperature range from 977 to 1144 K (1300 to 1600 F).

Uguccini, O. W.↗
NASA NTRS1977

Development of a drive system for a sequential space camera contract modification 4(S)

The brush type dc motor and clutch were eliminated from the design of the 16 mm space sequential camera design and replaced by an electronically commutated motor. The new drive system reduces the current consumption at 24 fps to 220 mA. The drive can be programmed and controlled externally from the multipurpose programmable timer/intervalometer, as well as being controlled locally from the camera.

Sharpsteen, J. T.↗
NASA NTRS1978

Airborne antenna coverage requirements for the TCV B-737 aircraft

The airborne antenna line of sight look angle requirement for operation with a Microwave Landing System (MLS) was studied. The required azimuth and elevation line of sight look angles from an antenna located on an aircraft to three ground based antenna sites at the Wallops Flight Center (FPS-16 radar, MLS aximuth, and MLS elevation) as the aircraft follows specific approach paths selected as representative of MLS operations at the Denver, Colorado, terminal area are presented. These required azimuth and elevation look angles may be interpreted as basic design requirements for antenna of the TCV B-737 airplane for MLS operations along these selected approach paths.

Southall, W. A., Jr.↗
NASA NTRS1978

Shuttle entry guidance

This paper describes the design of the entry guidance for the Space Shuttle Orbiter. This guidance provides the steering commands for trajectory control from initial penetration of the earth's atmosphere until the terminal area guidance is activated at an earth-relative speed of 2500 fps. At this point, the Orbiter is at a distance of about 50 nmi from the runway threshold, and at an altitude of about 80,000 ft. The entry guidance design is based on an analytic solution of the equations of motion defining the drag acceleration profile that meets the terminal criteria of the entry flight while maintaining the flight within systems and operational constraints. Guidance commands, which are based on a control law that ensures damping of oscillatory type trajectory motion, are computed to steer the Orbiter to this drag acceleration profile.

Harpold, J. C.↗
NASA NTRS1979

Static source locations for four nozzles mounted on a J-85 engine

The test nozzles included a round 17.5 in. diameter variable flap ejector (VFE) nozzle, a round 'stovepipe' nozzle, and a 104 tube suppressor nozzle operated both with and without an ejector shroud. The velocities tested ranged from 600 to 1600 fps at an approximate total temperature of 1400 R. The axial position of the noise sources during static operation was determined by jet velocity, Strouhal number, and direction of propagation. The velocity dependence was more evident for the 104 tube suppressor nozzle than for the conical nozzles tested. The results for both the VFE conical nozzle and the stovepipe conical nozzle indicate source locations to be much closer to the jet exit plane than expected. Corrections for near field effects were found to differ slightly for each nozzle tested. The corrections presented are simply the differences between the measured near field levels and the required near field levels if spherical spreading is assumed from source to far field.

Hoglund, L. E.↗
NASA NTRS1980

Downbursts and microbursts - An aviation hazard

Downburst and microburst phenomena occurring since 1975 are studied, based on meteorological analyses of aircraft accidents, aerial surveys of wind effects left behind downbursts, and studies of sub-mesoscale wind systems. It is concluded that microbursts beneath small, air mass thunderstorms are unpredictable in terms of weather forecast. Most aircraft incidents, however, were found to have occurred in the summer months, June through August. An intense microburst could produce 150 mph horizontal winds as well as 60 fps downflows at the tree-top level. The largest contributing factor to aircraft difficulties seemed to be a combination of the headwind decrease and the downflow. Anemometers and/or pressure sensors placed near runways were found effective for detecting gust fronts, but not for detecting downbursts. It is recommended that new detection systems placed on the ground or airborne, be developed, and that pilots be trained for simulated landing and go-around through microbursts.

Fujita, T. T.↗
NASA NTRS1982

Can the standard radiosonde system meet special atmospheric research needs

As a part of a rather comprehensive study of instrument reliability and error analysis, 21 balloon-borne dual radiosonde flights were launched and tracked with a precision C-band (FPS-16) radar as well as with the usual radiosonde tracking system. Radar provides an independent means for obtaining altitude data of order 10 meter accuracy. The 18 successful flights were investigated to determine repeatability of the pressure and temperature measurements. The obtained results show that the current aneroid pressure cell is the least repeatable member of the radiosonde's measurement components. Generally, the rms differences of the pressure measurements were found to be between 1 and 2 mbar throughout the altitude range of the instrument. Although these errors are large, they are not serious in the context of synoptic use. However, serious consideration must be given to these instrumental characteristics in connection with single station, nonsynoptic research objectives.

Schmidlin, F. J.↗
NASA NTRS1982

Requirements and design of the graphite/epoxy structural elements for the optical telescope assembly of the space telescope

The production of the Space Telescope's Metering Truss Structure (MTS) and Focal Plane Structure (FPS), which are of graphite/epoxy, is described. Graphite/epoxy laminates were chosen because of their high strength and stiffness, low weight, and a controlled coefficient of thermal expansion approaching zero. Photocopy masters, which are dimensionally accurate and stable photographic reproductions of full size engineering drawings, allowed the exact assembly of bonded or bolted parts by assembly mechanics, cutting costs and speeding production. While moisture absorption, high through-the-thickness coefficient of thermal expansion effects, and labor-intensive layup costs are potentially problematic in some cases, it is expected that solutions can be found through analytical and developmental programs.

Golden, C. T.↗
NASA NTRS1984

Goldstone R/D High Speed Data Acquisition System

A digital data acquisition system that meets the requirements of several users (initially the planetary radar program) is planned for general use at Deep Space Station 14 (DSS 14). The system, now partially complete, is controlled by VAX 11/780 computer that is programmed in high level languages. A DEC Data Controller is included for moderate-speed data acquisition, low speed data display, and for a digital interface to special user-provided devices. The high-speed data acquisition is performed in devices that are being designed and built at JPL. Analog IF signals are converted to a digitized 50 MHz real signal. This signal is filtered and mixed digitally to baseband after which its phase code (a PN sequence in the case of planetary radar) is removed. It may then be accumulated (or averaged) and fed into the VAX through an FPS 5210 array processor. Further data processing before entering the VAX is thus possible (computation and accumulation of the power spectra, for example). The system is to be located in the research and development pedestal at DSS 14 for easy access by researchers in radio astronomy as well as telemetry processing and antenna arraying.

Deutsch, L. J.↗