Search NASA⌕ Search

SEARCH · Search NASA

Results for “Frictional pressure gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1921

Pressure Drop in Radiator Air Tubes

This report describes a method for measuring the drop in static pressure of air flowing through a radiator and shows (1) a reason for the discrepancy noted by various observers between head resistance and drop in pressure; (2) a difference in degree of contraction of the jet in entering a circular cell and a square cell; (3) the ratio of internal frictional resistance to total head resistance for two representative types; (4) the effect of smoothness of surface on pressure gradient; and (5) the effects of supplying heat to the radiator on pressure gradient. The fact that the pressure gradients are found to be approximately proportional to the square of the rate of flow of air appears to indicate turbulent flow, even in the short tubes of the radiator. It was found that the drop in the static pressure in the air stream through a cellular radiator and the pressure gradient in the air tubes are practically proportional to the square of the air flow in a given air density; that the difference between the head resistance per unit area and the fall of static pressure through the air tubes in radiators is apparent rather than real; and that radiators of different types differ widely in the amount of contraction of the jet at entrance. The frictional resistance was found to vary considerably, and in one case to be two-thirds of the head resistance in the type using circular cells and one-half of the head resistance of the radiator type using square cells of approximately the same dimensions.

Parsons, S R↗
NASA NTRS2010

Boundary Layers, Transitions and Separation

Effects of roughness in boundary layers have to be addressed. Until adverse pressure gradient effects are understood, roughness will not significantly drive design. Mechanisms responsible for separation not understood. Effects on Zero Pressure Gradient boundary layers (shear stress). Effects on separation in pressure gradient (prediction of separation). Effect on scalar transport (heat transfer) not understood. Model for skin friction needed in simulations - first grid point likely to be in buffer layer. Definition of roughness important for useful experiments. A lot of validation experiments will be needed. How to get to ks for roughness of engineering interest? - depends on wavelength height, etc. for engineering interest? Re-discovering the wheel should be avoided: existing knowledge (theoretical and experimental) should find its way into the engineering models. It is a task of the industry to filter out the existing information in the literature for results relevant to its application, being external or internal.

Source record↗
NASA NTRS1972

Calculation of turbulent boundary layers with heat transfer and pressure gradient utilizing a compressibility transformation. Part 2: Constant property turbulent boundary layer flow with simultaneous mass transfer and pressure gradient

An analysis of the incompressible turbulent boundary layer, developing under the combined effects of mass transfer and pressure gradient, is presented in this paper. A strip-integral method is employed whereby two of the three governing equations are obtained by integrating the combined momentum and continuity equation to 50 percent and 100 percent, respectively, of the boundary-layer height. The latter equation is the usual momentum-integral equation; the former equation requires specification of shear. Accordingly, Clauser's equilibrium eddy-viscosity law is assumed valid at this point. The third and final equation is obtained by specifying that Stevenson's velocity profiles apply throughout the domain of interest, from which a skin-friction law can be derived. Comparisons of the numerical results with the experiments of McQuaid, which include combined effects of variable pressure gradient and mass transfer, show good agreement.

Boccio, J.↗
NASA NTRS1989

Diverging boundary layers with zero streamwise pressure gradient

The effects of spanwise divergence on the boundary layer forming between a pair of embedded streamwise vortices with the common flow between them directed toward the wall was studied. Measurements indicate that divergence controls the rate of development of the boundary layer and that large divergence significantly retards boundary layer growth and enhances skin friction. For strongly diverging boundary layers, divergence accounts for nearly all of the local skin friction. Even with divergence, however, the local similarity relationships for two-dimensional boundary layers are satisfactory. Although divergence modifies the mean development of the boundary layer, it does not significantly modify the turbulence structure. In the present experiments with a zero streamwise pressure gradient, it was found that spanwise divergence dit not significantly affect the Reynolds stress and the turbulent triple product distributions.

Pauley, Wayne R.↗
NASA NTRS1993

Diffusion effects on the helium abundance of the solar transition region and corona

The diffusion of helium in the solar transition region is studied by solving the mass and momentum conservation equations for a hydrogen-helium plasma given a representative temperature profile. Steady state solutions show that two distinct atmospheres may result. In cases where the thermal force on alpha-particles is balanced by the partial pressure gradient force, helium is the dominant coronal species. On the other hand, if it is the frictional force between protons and alpha-particles which balances the thermal force on alpha-particles then hydrogen is the major coronal component. In order to explore which of these solutions are attainable within reasonable time scales, the time-dependent equations are solved, starting from an initial state with a uniform helium abundance of 10 percent. The atmosphere as a whole is close to hydrostatic equilibrium, but due the thermal forces the individual elements are not. This force inbalance leads to a differential flow between species. It is found that this differential flow leads to a significant enhancement of the coronal helium abundance. Even for the relatively shallow temperature gradient used the helium abundance in the lower corona increases to 30 percent over a 24 hr period.

Hansteen, Viggo H.↗
NASA NTRS1993

Three-dimensional hypersonic shock wave/turbulent boundary-layer interactions

Experimental data for a series of three-dimensional shock wave/turbulent boundary-layer interaction flows at Mach 8.2 are presented. The test bodies, composed of sharp fins fastened to a flat plate test surface, were designed to generate flows with varying degrees of pressure gradient, boundary-layer separation, and turning angle. The data include surface pressure, heat transfer, and skin friction distributions as well as limited mean flowfield surveys in both the undisturbed and interaction regimes. The data were obtained for the purpose of validating computational models of these hypersonic interactions.

Kussoy, M. I.↗
NASA NTRS1978

Reynolds number and pressure gradient effects on compressible turbulent boundary layers

A detailed investigation of attached supersonic turbulent boundary layers over an extensive range of Reynolds numbers (12 x 10 to the 6th to 314 x 10 to the 6th) is presented. Experimental measurements were obtained for adverse pressure gradients ranging in magnitude from those of previous investigations to those approaching separation. The measurements include mean values of surface pressure and skin-friction, mean-flow profiles, and profiles of the three turbulent velocity fluctuation components and turbulent shear stress. Numerical solutions, employing three turbulence models of various degrees of complexity have been compared with the details of the measured flow fields. Generally, it was found that the more sophisticated turbulence models are superior to a mixing length model for predicting the Reynolds number and pressure gradient effects. However, some details of the turbulent fluctuations as well as the exact Reynolds number trends indicated by the data were not accurately predicted with any of the turbulence models considered.

Acharya, M.↗
NASA NTRS1982

Experimental investigation of turbulent wall-jets in the presence of adverse pressure gradients in a rectangular diffuser

An experimental study of wall static pressure distributions and mean velocity profiles along a duct and diffuser downstream of wall-jet injection was conducted over a range of diffuser total angles from 15 to 40 deg at injection to core flow mass flux ratios from 0 to 6. Pressure recovery in the diffuser increased with injection ratio and decreased with diffuser total angle. Peak velocities in the wall-jet decayed along the flow and the inner shear layer and outer mixing region grew in thickness along the flow. The inner layer was near similarity condition, but non-similar variations were found in the outer layer. Estimated wall shear stresses depended upon injection mass fluxes, downstream distance and diffuser total angle. Greater decay of peak velocity and larger friction coefficients were found in the diffuser than indicated by correlations from data for a wall-jet without a pressure gradient. At the largest diffuser total angle and the highest injection ratio flow reversal occurred in the core region.

Back, L.↗
NASA NTRS1991

Experimental study of boundary layer transition on a heated flat plate

A detailed investigation to the document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were done in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate, and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for momentum thickness Reynolds number, Re(sub theta) less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length and uniform heat flux. A small dependence of turbulence results on the freestream turbulence intensity was observed.

Sohn, K. H.↗
NASA NTRS1991

Experimental study of boundary layer transition on a heated flat plate

A detailed investigation to the document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were done in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate, and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for momentum thickness Reynolds number, Re(sub theta) less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length and uniform heat flux. A small dependence of turbulence results on the freestream turbulence intensity was observed.

Sohn, K. H.↗
NASA NTRS1974

Supersonic laminar base pressure, heat-transfer, and upstream influence correlations for small steps

Some results of the application of a unified theory of small disturbances in nonuniform high-speed boundary layers to the small-step problem for the case of supersonic laminar nonadiabatic flow are described. Comparisons with experimental data are given which show good agreement in a variety of physical features, including useful new base pressure and heat-transfer correlation relations. Using a small perturbation approach, an analytical theory is developed that predicts the steady-state pressure, temperature, and heat-transfer disturbance fields including suction or blowing through the step. Particular emphasis is placed on the important effects of the highly nonuniform flow across the boundary layer, lateral pressure gradients, and the upstream influence associated with viscous-inviscid interaction. Approximate analytical expressions for the wall pressure, skin friction, and heat-transfer perturbations and upstream influence distance are derived by a Fourier transformation approach.

Inger, G. R.↗
NASA NTRS1991

Experimental study of boundary layer transition with elevated freestream turbulence on a heated flat plate

A detailed investigation to document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were acquired in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities (TI) from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for R(sub theta) is less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length. The measured laminar value of Reynolds analogy factor was as much as 53 percent higher than the Pr(sup -2/3). A small dependence of turbulent results on TI was observed. Conditional sampling performed in the transitional boundary layer indicated the existence of a near-wall drop in intermittency, pronounced at certain low intermittencies, which is consistent with the cross-sectional shape of turbulent spots observed by others. Non-turbulent intervals were observed to possess large magnitudes of near-wall unsteadiness and turbulent intervals had peak values as much as 50 percent higher than were measured at fully turbulent stations. Non-turbulent and turbulent profiles in transitional boundary layers cannot be simply treated as Blasius and fully turbulent profiles, respectively. The boundary layer spectra indicate predicted selective amplification of T-S waves for TI is approximately 0.4 percent. However, for TI is approximately 0.8 and 1.1 percent, T-S waves are localized very near the wall and do not play a dominant role in transition process.

Sohn, Ki-Hyeon↗
NASA NTRSDate not supplied

Numerical Investigation of the Effect of Trailing Edge Thickness of Simulated CMC Blades on Loss Profiles

To understand such an aerodynamic characteristic of the CMC blades, we numerically simulated three different CMC blades with varying trailing edge thicknesses. We utilized both Large Eddy simulation (LES) with the dynamic subgrid closure as well a recently implemented Reynolds-averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model. We considered two sets of experimental test points with different Reynolds numbers at a given high-free stream turbulence range (Tu=~10-13%). The LES was previously validated by comparing with experimental data. We validated the RANS transition model against the ERCOFTAC experimental zero-pressure gradient smooth flat plate boundary layer at low- and high freestream turbulence offered by the experimental data of the Stripf’s for a turbine blade. We confirmed that the predicted skin friction and the heat flux agree well with the data. Finally, we computed the predicted pressure loading profiles, total loss distributions, and integrated loss of the three different CMC blades and made comparisons against the experimental data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Our paper will present the aforementioned results and discuss the ability of LES and RANS model of our choice to predict salient aerodynamic characteristics of the blades with the various trailing edge thickness effects.

LES↗
NASA NTRSDate not supplied

Numerical Investigation of the Effect of Trailing Edge Thickness of Simulated CMC Blades on Loss Profiles

To understand such an aerodynamic characteristic of the CMC blades, we numerically simulated three different CMC blades with varying trailing edge thicknesses. We utilized both Large Eddy simulation (LES) with the dynamic subgrid closure as well a recently implemented Reynolds-averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model. We considered two sets of experimental test points with different Reynolds numbers at a given high-free stream turbulence range (Tu=~10-13%). The LES was previously validated by comparing with experimental data. We validated the RANS transition model against the ERCOFTAC experimental zero-pressure gradient smooth flat plate boundary layer at low- and high freestream turbulence offered by the experimental data of the Stripf’s for a turbine blade. We confirmed that the predicted skin friction and the heat flux agree well with the data. Finally, we computed the predicted pressure loading profiles, total loss distributions, and integrated loss of the three different CMC blades and made comparisons against the experimental data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Our paper will present the aforementioned results and discuss the ability of LES and RANS model of our choice to predict salient aerodynamic characteristics of the blades with the various trailing edge thickness effects.

LES↗
NASA NTRS1987

Influence of disk leakage path on labyrinth seal inlet swirl ratio

The results of numerous investigators have shown the importance of labyrinth seal inlet swirl on the calculated dynamic stiffness of labyrinth seals. These results have not included any calculation of inlet leakage swirl as a function of geometry and sealing conditions of the given seal. This paper outlines a method of calculating the inlet swirl at a given seal by introducing a radial chamber to predict the gas swirl as it goes from the stage tip down to the seal location. For a centrifugal compressor, this amounts to including the flow path from the impeller discharge, down the back of the disk or front of the cover, then into the shaft seal or eye packing, respectively. The solution includes the friction factors of both the disk and stationary wall with account for mass flow rate and calculation of radial pressure gradients by a free vortex solution. The results of various configurations are discussed and comparisons made to other published results of disk swirl.

Kirk, R. Gordon↗
NASA NTRS1991

An experimental study of a three-dimensional shock wave/turbulent boundary-layer interaction at a hypersonic Mach number

Experimental data for a series of three-dimensional shock-wave/turbulent-boundary-layer interaction flows at Mach 8.2 are presented. The test bodies, composed of sharp fins fastened to a flat-plate test surface, were designed to generate flows with varying degrees of pressure gradient, boundary-layer separation, and turning angle. The data include surface-pressure, heat-transfer, and skin-friction distributions, as well as limited mean flowfield surveys both in the undisturbed and interaction regimes. The data were obtained for the purpose of validating computational models of these hypersonic interactions.

Kussoy, M. I.↗
NASA NTRS1983

Influence of wall permeability on turbulent boundary-layer properties

Experimental boundary-layer studies of a series of low pressure drop, permeable surfaces have been conducted to characterize their surface interaction with a turbulent boundary layer. The models were flat and tested at nominally zero pressure gradient in low speed air. The surfaces were thin metal sheets with discrete perforations. Direct drag balance measurements of skin friction indicate that the general effect of surface permeability is to increase drag above that of a smooth plate reference level. Heuristic arguments are presented to show that this type of behavior is to be expected. Other boundary-layer data are also presented including mean velocity profiles and conditionally sampled streamwise velocity fluctuations (hot wire) for selected models.

Wilkinson, S. P.↗
NASA NTRS1989

Flow unsteadiness effects on boundary layers

The development of boundary layers at high subsonic speeds in the presence of either mass flux fluctuations or acoustic disturbances (the two most important parameters in the unsteadiness environment affecting the aerodynamics of a flight vehicle) was investigated. A high quality database for generating detailed information concerning free-stream flow unsteadiness effects on boundary layer growth and transition in high subsonic and transonic speeds is described. The database will be generated with a two-pronged approach: (1) from a detailed review of existing literature on research and wind tunnel calibration database, and (2) from detailed tests in the Boundary Layer Apparatus for Subsonic and Transonic flow Affected by Noise Environment (BLASTANE). Special instrumentation, including hot wire anemometry, the buried wire gage technique, and laser velocimetry were used to obtain skin friction and turbulent shear stress data along the entire boundary layer for various free stream noise levels, turbulence content, and pressure gradients. This database will be useful for improving the correction methodology of applying wind tunnel test data to flight predictions and will be helpful for making improvements in turbulence modeling laws.

Murthy, Sreedhara V.↗