Search NASA⌕ Search

SEARCH · Search NASA

Results for “GAS WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

The Effect of SiC Addition on Microstructure and Mechanical Properties of Gas Tungsten Arc-Welded Ti-6Al-4V Alloy

In the present study, SiC powder was added in situ for bead-on-plate weldments and fusion butt joints to modify the microstructure and the corresponding mechanical properties. Cross sections of bead-on-plate welds demonstrated that the SiC addition resulted in significant changes of the titanium microstructure. Specifically, a fine lamellar structure of α-phase with a small amount of intergranular β-titanium within the fusion zone could be established. Moreover, the size of prior β-grains was significantly reduced. After welding, no intermetallic silicides were observed. In the fusion zone of the SiC-enhanced samples, a small increase in hardness resulted, and the samples showed an increase in tensile strength, yield strength and elongation.

36 MATERIALS SCIENCE↗

Produce ZrH Moderator Material

This reports complete Milestone M2.2.3 Produce zirconium hydride moderator material. In this milestone, we report the successful fabrication of FeCrAl alloys cladded zirconium hydride moderator. Different types of crucible designs were presented, including the basic design with bar cladding material, basic design with tube cladding material, and crucible design with position holding function. Mo and FeCrAl were used as the trial cladding materials. The welding techniques and procedures were reported and discussed. Totally three welding techniques were adopted in the development of moderator cladding, and they are electron beam welding (EBW), laser welding (LW), and gas tungsten arc welding (GTAW). After welding, all cladded crucibles were evaluated with two kinds of leak testing, the helium leak test for minor leakage and the bubble test for major leakage. Due to the concern of the poor neutronics performance, Mo was not ideal for future moderator cladding application. Therefore, detailed characterization of the Mo cladded zirconium hydride was not pursued. Instead, the characterization of FeCrAl cladded zirconium hydride was performed. We discussed two material conditions (i.e., as machined and pre-oxidized conditions) prior to the cladding process, evaluated thermal stability of cladded zirconium hydride moderator through directly measuring hydrogen release, and characterized the zirconium hydride following the thermal desorption measurement. The results showed pre-oxidized FeCrAl is capable of efficiently preventing hydrogen release from the moderator assembly.

36 MATERIALS SCIENCE↗

Analysis of Favorable Process Conditions for the Manufacturing of Thin-Wall Pieces of Mild Steel Obtained by Wire and Arc Additive Manufacturing (WAAM)

Here, one of the challenges in additive manufacturing (AM) of metallic materials is to obtain workpieces free of defects with excellent physical, mechanical, and metallurgical properties. In wire and arc additive manufacturing (WAAM) the influences of process conditions on thermal history, microstructure and resultant mechanical and surface properties of parts must be analyzed. In this work, 3D metallic parts of mild steel wire (American Welding Society-AWS ER70S-6) are built with a WAAM process by depositing layers of material on a substrate of a S235 JR steel sheet of 3 mm thickness under different process conditions, using as welding process the gas metal arc welding (GMAW) with cold metal transfer (CMT) technology, combined with a positioning system such as a computer numerical controlled (CNC) milling machine. Considering the hardness profiles, the estimated ultimate tensile strengths (UTS) derived from the hardness measurements and the microstructure findings, it can be concluded that the most favorable process conditions are the ones provided by CMT, with homogeneous hardness profiles, good mechanical strengths in accordance to conditions defined by standard, and without formation of a decohesionated external layer; CMT Continuous is the optimal option as the mechanical properties are better than single CMT.

36 MATERIALS SCIENCE↗

Evaluation Of Four Welding Arc Processes Applied To 6061 Aluminium Alloy

At a time when greenhouse gas emissions must be reduced, the use of the aluminium alloys is expanding, in particular in the transportation industry. In order to extend the possibilities of aluminium assembly design, new Metal Inert Gas (MIG) welding processes have been conceived. They work at lower temperatures than usual arc processes (classic MIG or Tungsten Inert Gas). This study compares four arc welding processes, applied to the 6061 aluminium alloy. These four weld processes have been studied through the metallurgical analysis of the weld beads. Metallography, micro-hardness testings, X Ray radiography have been carried out on the produced weld beads. The processes are classified according to the quality of the beads like geometry of beads, size of the heat affected zone and presence of defects.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Three-Layer TIG-Welded 2219 Aluminum Alloys with Dissimilar Heat Treatments

2219-C10S and 2219-CYS aluminum alloys are 2219 aluminum alloys with different heat treatment processes, and they have been widely used in the aerospace industry. In the present study, 2219-C10S and 2219-CYS aluminum alloys were butt-welded by three-layer tungsten inert gas arc welding (with the welding center of the third layer shifted toward the CYS side), and the microstructure characteristics and mechanical properties of the welded joint were investigated. The lamellar θ′ phases, the bulk or rod θ phases, and the coarse rod-shaped or pancake-shaped Al-Cu-Fe-Mn phases coexisted in the two aluminum alloys. The Cu content of the α-Al matrix and the distribution of eutectic structures of different welding layers in the weld zone (WZ) were varied, implying that the segregation degrees of the Cu element were different due to the different welding thermal cycles in different welding layers. The microhardness values of the CYS side were much higher than those of the C10S side in each region on both sides of the joint. The tensile test deformation was concentrated mainly in the regions of WZ and the over aged zone (OAZ), where the microhardness values were relatively low. The main deformation concentrated region was transferred from the CYS side to the C10S side with the increase in the tensile load during the tensile test. The fracture behavior of the tensile test showed that the macroscopic crack initiated near the front weld toe had gone through the crack blunt region, the shear fracture region of the partially melted zone (PMZ), and the shear fracture region of OAZ. Meanwhile, the fracture characteristics gradually evolved from brittle to ductile. The concentrated stress and the dense eutectic structure in the region near the front weld toe of the C10S side contributed to the fracture of the joint. The shift of the welding center of the third layer to the CYS side resulted in two effects: (i) the microhardness values from the middle layer to the top layer in the PMZ of the CYS side were the most significantly increased and (ii) the distance between the front weld toe and the fusion line of the CYS side was significantly larger.

36 MATERIALS SCIENCE↗

Remote Evaporator Vessel Repair by Robotics and Powder Injection Laser Welding - 18107

In February 2016 a leak was identified in the 25H evaporator at the Savannah River Site (SRS). The 25H evaporator is used to manage water volume in high level waste (HLW) tanks during solid salt cake and sludge removal. The location and the cause of the leak were unknown. Orano Federal Services (formerly AREVA Federal Services) applied its robotics expertise and commercial nuclear expertise to perform the inspection. Orano and Framatome (formerly AREVA NP INC) combined a BROKK, a commonly used tracked vehicle with remote control, with the KUKA, an automated robotic arm, commonly used in automobile manufacturing, to perform the partial dismantlement and inspection. Once inspection was complete and the leak was identified, Orano conducted a study on two welding processes: Gas Tungsten Arc (GTA-Tig) and Powder Injection Laser Welding. Based on the inspection of the SRS HLW evaporator's material type being Hastelloy{sup R}, along with the remote repair and material thin wall condition, the Powder Injection Laser Welding was chosen for this application. Orano has developed the remote powder injection laser welding and delivery process that will be used to conduct the repair of the SRS HLW evaporator in the fall of 2017. The process includes robotic delivery of components and robotic performance of the weld. Specialized robotic equipment were developed or adapted from other industries to perform the high hazard job of repairing an eroded section of the evaporator pot. The integration of multiple innovative remote techniques provides a unique solution in a highly radioactive environment. These techniques and innovations can be capitalized upon to solve many different remote repairs on equipment resulting in time savings, reduced dose to personnel, and recovery of initial investment in equipment. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Fatigue crack growth rates of X100 steel welds in high pressure hydrogen gas considering residual stress effects

Fatigue crack growth rate (FCGR) data were measured in high pressure hydrogen gas versus stress intensity factor range (ΔK) in specimens removed from a X100 welded steel pipe. Three distinct regions of the pipe weld were examined: base metal, weld fusion zone, and heat affected zone. Tests were performed at a load ratio (R) of 0.5, frequency of 1 Hz, and at a hydrogen gas pressure of 21 MPa. Tests were also performed in air at 10 Hz as a reference. Fatigue crack growth rates were observed to be over an order of magnitude higher for tests performed in hydrogen compared to the rates from tests in air. Residual stress measurements were collected on identical specimens cut from the base metal, weld, and heat affected zone to account for their influence on measured FCGR data. The slitting method provided residual stress and residual stress intensity factor (K res ), the effect of which was removed from the FCGR data using K norm in order to provide a more direct comparison of crack growth resistance of the base metal, weld and heat affected zone. Prior to accounting for residual stress, FCGR in hydrogen gas appeared to be highest in the weld fusion zone. Furthermore, after accounting for residual stress effects, the weld fusion zone FCGR data converged to the base metal FCGR data, which underscores the importance of accounting for residual stress effects when assessing fatigue performance.

42 ENGINEERING↗

The Effect of Arc Current on Microstructure and Mechanical Properties of Hybrid LasTIG Welds of High-Strength Low-Alloy Steels

A hybrid laser-tungsten inert gas (LasTIG) welding system was applied for 3-mm-thick S460MC and S700MC high-strength low-alloy steel sheet butt welding with the aim to reduce the cooling rate compared with laser welding. The effect of the electric current was evaluated. Increasing arc current led to the increase of fused metal and heat-affected-zone (HAZ) dimensions. Fused metal grains were larger whereas the microhardness increase toward the base metal was lower at higher currents in this region. Microhardness peaks corresponding to the coarse-grained HAZ were reduced at higher currents for S460MC but were almost not affected in S700MC. The tensile strength of both the laser weld and LasTIG welds was comparable to the base metal for both alloys.

36 MATERIALS SCIENCE↗

Design, Development and Testing of Inconel Alloy IN718 Spherical Gas Bottle for Oxygen Storage

This paper describes the details of design, manufacture and testing of 200 mm diameter spherical gas bottle of Inconel 718 (IN718) with nominal wall thickness of 2.3 mm. Gas bottle was designed for the specified internal pressure loading with a thickness of 2.9 mm at the circumferential weld which was brought down to 2.3 mm at the membrane locations. Hemispherical forgings produced through closed-die hammer forging were machined and electron beam welded to produce a spherical gas bottle. Duly welded gas bottle was subjected to standard aging treatment to achieve the required tensile strength. Aged gas bottle was inspected for dimensions and other stringent quality requirements using various nondestructive testing techniques. After inspection, gas bottle was subjected to pressure test for maximum expected operating pressure and proof pressure of 25 and 37.5 MPa, respectively. Strain gauges were bonded at different locations on the gas bottle to monitor the strains during the pressure test and correlated with the predicted values. The predicted strain matched well with the experimental strain confirming the design and structural integrity.

36 MATERIALS SCIENCE↗

Fabrication and Evaluation of Weldments for Alloy 709 Commercial Heat Plates (FY 2019)

Alloy 709 is an attractive candidate construction material for the Sodium Fast Reactor (SFR). As part of the Alloy 709 Intermediate Term Test Program, this work covers the development of the technical basis for weld fabrication and weld qualification of Alloy 709. The phase of research reported herein focused on the issue of weld solidification cracking recently experienced in some experimental heats of Alloy 709 with relatively high phosphorous levels. The computational simulation results revealed that that phosphorous has the most important impact on solidification behavior. Phosphorous is expected to significantly increase the susceptibility of weld solidification cracking of Alloy 709. A strategy to successfully weld Alloy 709 having wide range of chemistries without weld solidification cracking is developed to support ASME code qualification. The strategy includes use of low phosphorous level weld wire to weld Alloy 709 base metal having relatively high phosphorous. The welding experiment and subsequent weld qualification testing per ASME Section IX, conducted this reporting period, confirmed that a commercial heat Alloy 709 with 140wppm phosphorous can be successfully welded using a low phosphorous (20wppm) weld wire using the gas tungsten arc welding process and welding input levels typically used by industry. On the other hand, micro cracks are formed when the phosphorous level in the weld wire increases to 140wppm, which requires additional R&D to develop appropriate welding techniques to produce code qualified welds.

36 MATERIALS SCIENCE↗

Gigacycle Fatigue Strength Evaluation of Welded 316L Stainless Steels for Mercury Target Vessel

At the Materials and Life Science Experimental Facility (MLF) in J-PARC, liquid mercury target for the pulsed spallation neutron source is in operation. An enclosure vessel for the liquid mercury target made of type 316L stainless steel (SS316L) suffers two kinds of cyclic stress during operation. One is the thermal stress due to the internal heating and swings by proton beam trip. The other is the impulsive stress by the pressure waves generated by the proton beam injection. The total number of loading cycles for the former is ∼104, and the latter is ∼4 × 108 for a year operation in the J-PARC mercury target vessel. The target vessel is assembled by an electron beam welding (EBW) and a gas tungsten arc welding (GTAW). However, fatigue data of welded SS316L up to gigacycle is limited. Ultrasonic fatigue testing, applying load cycles by utilizing ultrasonic resonance, for the welded SS316L was performed to investigate the effect of welding on fatigue behavior up to a gigacycle. The result showed that the fatigue strength degradation by EBW and EBW with GTAW were not recognized up to 109 cycles. Crack initiation in welded specimens nucliated at off-center areas of the specimen whereas the cracks in base metal specimen originated at the specimen center.

Naoe, Takashi [Japan Atomic Energy Agency (JAEA)]↗

Mechanism study on the effects of side assisting gas velocity during CO{sub 2} laser welding process

An experimental study on the effects of side assisting gas during CO{sub 2} laser welding has been carried out, and it is found that side assisting gas velocity can significantly affect the laser induced plasma and the weld cross-sectional geometry. In order to get better understanding on the associated mechanism, a three dimensional model based on the conservation laws of mass, momentum, and energy has been developed to simulate the spatial distributions of plasma temperature under different side assisting gas velocities. Furthermore, ray-tracing method is employed to investigate the variation of bremsstrahlung absorption and power density distribution on keyhole walls at different side assisting gas velocities with the assumption of conical keyhole shape. The results show that the diminishing of refraction and bremsstrahlung absorption due to an increase in side assisting gas velocity results in an increase in heat transfer efficiency, which contributes to the increase of weld cross-sectional area and penetration depth.

36 MATERIALS SCIENCE↗

Welding investigation of a wrought FeMnAl steel for armor application

A new wrought FeMnAl steel contains high Mn content and high Al content. This steel has high strength. When it is compared to conventional steels with the similar strength, its density is lower. FeMnAl steels can be used in armor vehicle manufacturing, in which welding is a common practice to join the steel plates together. The welding of FeMnAl steels has not been sufficiently studied before. Here, this work studied the weldability and weld microstructure of an FeMnAl steel and provided useful data for the welding practice of FeMnAl steels. The influences of weld filler metals and shielding gases were studied, using single-pass bead-on-plate gas metal arc welding (GMAW) and gas tungsten arc welding (GTAW) two processes. The optimal filler metals and shielding gases have been determined to achieve the better weldability. Autogenous GTAW and electron beam welding were also conducted. Cracks were found in the HAZ in the GMAW welds and electron beam welds. Fewer or no cracks were found in the HAZ of GTAW welds. SEM, SEM/EDX, TEM, TEM/EDX, and EBSD were used to analyze the grain boundaries in the HAZ and the cracks. The grain boundaries of FeMnAl base metal are mostly high angle grain boundaries (HAGBs), which attract impurity and solute atoms and cause intergranular cracking. The proposed cracking mechanisms are liquation cracking and ductility-dip cracking. It was found that GTAW provides much better weldability for the FeMnAl steel than GMAW and EBW.

FeMnAl steel↗

Robust Dissimilar Metal Friction Welded Spool for Enhanced Capability for Steam Power Components (Final Program Report)

This project successfully demonstrated the feasibility and advantages of producing durable, friction-welded dissimilar-metal spools, both with and without transition pieces, as well as the use of advanced oxidation-protective coatings for steam power applications. The work encompassed the optimization and full-scale production of NFA tubing, overcoming manufacturing and processing challenges to achieve enhanced strength, creep, and fatigue properties validated by extensive microstructural characterization. Optimized welding techniques were developed and refined for joining dissimilar materials, resulting in defect-free welds optimized for both low- and high-pressure boiler circuits. Systematic evaluation of welding parameters, coupled with heat treatments, ensured reliable performance and minimized weld defects such as banding and cracking. Comprehensive mechanical and non-destructive testing, including tensile, bend, fatigue, and CT scanning, confirmed the superior integrity and durability of the friction-welded joints under representative service conditions. To address oxidation-related degradation, a range of protective alloy coatings—such as IN625, APMT, Duplex 2507, and FeCrAlY—were selected and evaluated for their ability to counteract oxide notch formation at dissimilar metal interfaces. These coatings demonstrated improved oxidation resistance and long-term stability under thermal cycling, thereby extending weld service life. Thermal cyclic testing and long-term studies captured the phase stability and diffusion behavior of coated and uncoated configurations. Validated models for low-cycle fatigue (LCF), creep, and thermal mechanical fatigue (TMF) were developed to predict component life and failure modes. These models confirmed that friction-welded configurations exhibited significantly enhanced performance compared to conventional gas-tungsten arc welding (GTAW), with up to 7× improvement in creep resistance and at least 2× enhancement in fatigue properties. The introduction of a tailored transition piece further reduced thermally induced strains, enhancing fatigue life. The results demonstrate a robust pathway for retrofitting existing steam fleet components and upgrading future equipment to deliver substantially improved cold-start cycling behavior and reduction of unplanned outages due to premature weld failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Temperature and time effects of post-weld heat treatments on tensile properties and microstructure of Zircaloy-4

Opportunities exist to expand the application of Zircaloy-4 (Zry-4) into lower-temperature (<100°C) applications. Welded areas within these structures are potential failure points and post-weld heat treatments (PWHTs) are not yet standardized for application in this temperature range. Zry-4 tungsten inert gas (TIG) welds were given PWHTs from 450-900°C with hold times from 0.5-48 hours to investigate changes to tensile properties and microstructure. Treatment of 800°C for 1 hour was found to produce the most ductile material, measured by total elongation of the tensile bar (16.5%). Furthermore, both PWHT time and temperature were observed to increase total elongation, except in extreme (>800°C or >18hours) cases, but the effect of temperature was stronger. The second order cumulative annealing parameter shows a trend with tensile properties. Average grain sizes in the fusion zone and heat affected zone did not change under any of the PWHTs until the development of an undesirable blocky-alpha phase, which was only observed to form in the heat affected zones for hold times greater than 18hr at 800°C.

36 MATERIALS SCIENCE↗

Microstructure Evolution, Structural Integrity, and Hot Corrosion Performance of Nitrogen-Enhanced Stainless Steel Welds

This work articulated the multi-pass, gas tungsten arc welding by adopting pulsating current for joining nitrogen-enhanced, low-carbon austenitic stainless steel, AISI 316L(N). An austeno-ferrite stainless steel (ER2594) and an over-alloyed (ERNiCrMo-3) fillers were employed to join 6-mm-thick plates of AISI 316L(N). Acicular and lathy ferrite in the weld zone of ER2594 and the occurrence of secondary phases in the fusion zone of over-alloyed filler were observed. The notch tensile strength data attested that the joint strength was greater for the welds employing an over-alloyed filler. This study also affirms that the welds obtained with ER2594 filler resulted in better impact toughness (144 J) compared with ERNiCrMo-3 filler and base metal. Also the notch impact toughness of ER2594 weldment is increased to 60% in comparison with that of candidate metal. Corrosion studies were also performed by exposing the coupons in a eutectic salt mixture comprising of 40%K{sub 2}SO{sub 4}-60%NaCl for 50 cycles at 650 °C. It is observed that the weld zone employing over-alloyed filler experienced better high-temperature corrosion resistance compared to the base metal. The specific results of this investigation will be of greater demand to the nuclear and marine applications utilizing these joints.

36 MATERIALS SCIENCE↗

Manufacturing and Performance Assessment of Stamped, Laser Welded, and Nitrided FeCrV Stainless Steel Bipolar Plates for Proton Exchange Membrane Fuel Cells

A manufacturing and single-cell fuel cell performance study of stamped, laser welded, and gas nitrided ferritic stainless steel foils in an advanced automotive bipolar plate assembly design was performed. Two developmental foil compositions were studied: Fee20Cre4V and Fee23Cre4V wt.%. Foils 0.1 mm thick were stamped and then laser welded together to create single bipolar plate assemblies with cooling channels. The plates were then surface treated by pre-oxidation and nitridation in N2e4H2 based gas mixtures using either a conventional furnace or a short-cycle quartz lamp infrared heating system. Single-cell fuel cell testing was performed at 80 C for 500 h at 0.3 A/cm2 using 100% humidification and a 100%/40% humidification cycle that stresses the membrane and enhances release of the fluoride ion and promotes a more corrosive environment for the bipolar plates. Periodic high frequency resistance potential-current scans during the 500 h fuel cell test and posttest analysis of the membrane indicated no resistance increase of the plates and only trace levels of metal ion contamination.

Brady, Michael P↗