SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
We present a generalized raytracing inversion scheme which can be used when occultation data is acquired with a receiver within (e.g., on mountain top) or outside (i.e., in space) the atmosphere.
A sequential navigation algorithm for a navigator using the Global Positioning System satellites is developed and tested for both noise-free and noisy system models. Data from a six-hour flight from California to Hawaii (C5A aircraft) simulates a true user to test the accuracy of the user's position for a sequential navigation system. For error reduction in the user's position in the sequential navigation system (considering 100 m as a maximum average error tolerated by any low-cost GPS user) an analysis of error sources in the sequential system has led to the use of range-ephemeris rate to translate ranges to a common point in time and to use velocity aiding at the time of a satellite disappearance. To reduce the user's position and velocity errors in a noisy navigation system an 'alpha-beta' two-pole filter is implemented whose optimum alpha is obtained experimentally. A user's position error of 73 m at noise range error of 30.48 (1sigma) is achieved.
Launched on 10 August, 1992, the Topex/Poseidon satellite is a joint project of NASA and the French space agency CNES. The purpose of this Earth orbiting altimetric satellite (for brevity, referred to as Topex) is to enable monitoring of the ocean topography to higher levels of accuracy than previously achieved. Essential to obtaining this greater level of accuracy is the use of improved navigational systems which can yield position estimates for Topex good to a few centimeters. One of the navigational systems utilized by Topex is the Global Positioning System (GPS) -- a network of navigational beacons that has become widely used in many areas beside spacecraft navigation...
The National Bureau of Standards/Global Positioning System (NBS/GPS) receiver is discussed. It is designed around the concept of obtaining high accuracy, low cost time and frequency comparisons between remote frequency standards and clocks with the intent to aid international time and frequency coordination. Preliminary tests of this comparison technique between Boulder, CO and Washington, D.C indicate the ability to do accurate time transfer to better that 10 ns, and frequency measurements to better than 1 part in 10 to the 14th power. The hardware and software of the receiver is detailed. The receiver is fully automatic with a built-in 0.1 ns resolution time interval counter. A microprocessor does data processing. Satellite signal stabilities are routinely at the 5 ns level for 15 s averages, and the internal receiver stabilities are at the 1 ns level.
The filtering of the satellite range and range-rate measurements from single channel sequential Global Positioning System receivers is usually done with an extended Kalman filter which has state variables defined in terms of an orthogonal navigation reference frame. An attractive suboptimal alternative is range-domain filtering, in which the individual satellite measurements are filtered separately before they are combined for the navigation solution. The main advantages of range-domain filtering are decreased processing and storage requirements and simplified tuning. Several range filter mechanization alternatives are presented, along with an innovative approach for combining the filtered range-domain quantities to determine the navigation state estimate. In addition, a method is outlined for incorporating measurements from auxiliary sensors such as altimeters into the navigation state estimation scheme similarly to the satellite measurements. A method is also described for incorporating inertial measurements into the navigation state estimator as a process driver.
The filtering of the satellite range and range-rate measurements from single channel sequential Global Positioning System receivers is usually done with an extended Kalman filter which has state variables defined in terms of an orthogonal navigation reference frame. An attractive suboptimal alternative is range-domain filtering, in which the individual satellite measurements are filtered separately before they are combined for the navigation solution. The main advantages of range-domain filtering are decreased processing and storage requirements and simplified tuning. Several range filter mechanization alternatives are presented, along with an innovative approach for combining the filtered range-domain quantities to determine the navigation state estimate. In addition, a method is outlined for incorporating measurements from auxiliary sensors such as altimeters into the navigation state estimation scheme similarly to the satellite measurements. A method is also described for incorporating inertial measurements into the navigation state estimator as a process driver.
In a system for deriving position, velocity, and acceleration information from a received signal emitted from an object to be tracked wherein the signal comprises a carrier signal phase modulated by unknown binary data and experiencing very high Doppler and Doppler rate, this invention provides combined estimation/detection apparatus for simultaneously detecting data bits and obtaining estimates of signal parameters such as carrier phase and frequency related to receiver dynamics in a sequential manner. There is a first stage for obtaining estimates of the signal parameters related to phase and frequency in the vicinity of possible data transitions on the basis of measurements obtained within a current data bit. A second stage uses the estimates from the first stage to decide whether or not a data transition has actually occurred. There is a third stage for removing data modulation from the received signal when a data transition has occurred and a fourth stage for using the received signal with data modulation removed therefrom to update global parameters which are dependent only upon receiver dynamics and independent of data modulation. Finally, there is a fifth stage for using the global parameters to determine the position, velocity, and acceleration of the object.
A hand-held Global Positioning System receiver was used to determine the precise locations of villages, houses, gardens, and other cultural and environmental features in poorly mapped South American rain forests. The Magellan NAV 1000 unit profides extremely accurate latitude and longitude information, but determination of altitude is problematical. Overall, the receiver effectively allows anthropologists to obtain essential locational data useful for categorizing land uses, mapping tribal boundaries, and other applications in regions where environmental conditions are harsh and/or accessibility is difficult.
Launched on August 10, 1992, the Topex/Poseidon satellite is a joint project of NASA and the French space agency CNES. The pupose of this Earth orbiting altimetric satellite (for brevity, referred to as Topex) is to enable monitoring of the ocean topography to higher levels of accuracy than previously achieved.
Explore the source record for details and available documents.
Fermi GLAST s 5-year mission objectives: a) Explore the most extreme environments in the Universe. b) Search for signs of new laws of physics and what composes the mysterious Dark Matter. c) Explain how black holes accelerate immense jets of material to nearly light speed. d) Help crack the mysteries of gamma-ray bursts. e) Answer long-standing questions across a broad range of topics, including solar flares, pulsars and the origin of cosmic rays.
No abstract available
A simple pulse overlay circuit using a logic OR gate was developed to overlay a precise leading edge 1 pulse per second time reference marker from a global positioning system receiver onto a non-return -to- zero-level pulse code modulation telemetry data stream to validate time stamp accuracy and measure propagation delay in telemetry equipment. A pulse overlay (PO) circuit was designed to produce a time reference marker within a pulse code modulation (PCM) telemetry data stream that was recorded and analyzed to validate an IRIG Standard 106-17 Chapter 10 recorder’s time stamp accuracy [1]. A manufacturer of a newly purchased Chapter 10 recorder claimed the time stamp accuracy to be better than 10 microseconds (μs) with only IRIG-B120 (IRIG-B) input and better than 1 μs with IRIG-B and one pulse per second (1PPS) inputs. The PO circuit and a Chapter 10 recorder test setup were used to verify the vendor’s data-time synchronization claims and to justify infrastructure upgrade costs to connect additional cables to each purchased recorder. The circuit was also used to measure the propagation delay (PD) of a long distance Telemetry multiplexer/demultiplexer telecommunication system which the manufacturer did not provide a PD specification. Using the one pulse per second time reference marker of the global positioning system receiver and the pulse overlay circuit to overlay the one pulse per second variable pulse width signal into a pulse code modulation telemetry stream provided an excellent means to validate time stamp accuracy within a Chapter 10 recorder and to measure propagation delays within a normal telemetry operating environment. The positive results from the Chapter 10 recorder tests validated the vendor’s claims and justified the implementation to add the one pulse per second signal to the range Chapter 10 recorders. The pulse overlay circuit and test setups defined in this paper can easily be used to measure other telemetry equipment.
A simple pulse overlay circuit using a logic OR gate was developed to overlay a precise leading edge 1 pulse per second time reference marker from a global positioning system receiver onto a non-return -to- zero-level pulse code modulation telemetry data stream to validate time stamp accuracy and measure propagation delay in telemetry equipment.
The hardware, software, and interface between them was investigated for a low dynamics, nonhostile environment, low cost GPS receiver (GPS Z set). The set is basically a three dimensional geodetic and way point navigator with GPS time, ground speed, and ground track as possible outputs in addition to the usual GPS receiver set outputs. Each functional module comprising the GPS set is described, enumerating its functional inputs and outputs, leading to the interface between hardware and software of the set.
Improved technique for preprocessing data from Global Positioning System (GPS) receiver reduces processing time and number of data to be stored. Technique optimal in sense it maintains strength of data. Also sometimes increases ability to resolve ambiguities in numbers of cycles of received GPS carrier signals.
Using a network of 15 global GPS receivers, GPS data is returning to JPL via the open Internet to determine the orbits and clocks of the GPS constellation in real-time.
GPS-based estimates of precipitable water vapor (PWV) may be useful in numerical weather models to improve short-term weather predictions. To be effective in numerical weather prediction models, GPS PWV estimates must be produced with sufficient accuracy in near real time. Several estimation strategies for the near real time processing of GPS data are investigated.