Search NASA⌕ Search

SEARCH · Search NASA

Results for “GRAIN ORIENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

An experimental study of high Tc superconducting microstrip transmission lines at 35 GHz and the effect of film morphology

Microstrip transmission lines in the form of ring resonators were fabricated from a number of in-situ grown laser ablated films and post-annealed co-sputtered YBa2Cu3O(7-x) films. The properties of these resonators were measured at 35 GHz and the observed performance is examined in light of the critical temperature (Tc) and film thickness, and also the film morphology, which is different for the two deposition techniques. It is found that Tc is a major indicator of the film performance for each growth type, with film thickness becoming important as it decreases towards 1000 A. It is also found that the films with a mixed grain orientation (both a-axis and c-axis oriented grains) have poorer microwave properties as compared with the primarily c-axis oriented material. This is probably due to the significant number of grain boundaries between the different crystallites, which may act as superconducting weak links and contribute to the surface resistance.

Chorey, C. M.↗

Layered-structural monoclinic–orthorhombic perovskite La{sub 2}Ti{sub 2}O{sub 7} to orthorhombic LaTiO{sub 3} phase transition and their microstructure characterization

The layered-structural ceramics, such as lanthanum titanate (La{sub 2}Ti{sub 2}O{sub 7}), have been known for their good temperature and low dielectric loss at microwave frequencies that make them good candidate materials for high frequency applications. However, few studies have been conducted on the synthesis optimization by sol gel reaction, in particular by acrylamide polymerization route. The interest in La{sub 2}Ti{sub 2}O{sub 7} ceramic has been greatly increased recently due to the effect of oriented grains. This anisotropy of the microstructure leads to anisotropy in dielectric, electrical and mechanical properties. In this study, grain oriented lanthanum titanate was produced by the sol–gel acrylamide polymerization route. The characterizations of the samples were achieved by thermal analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and transmission electron microscopy (TEM). X-ray diffraction indicates that the formation of monoclinic perovskite La{sub 2}Ti{sub 2}O{sub 7} nanocrystals is a necessary first step to obtain orthorhombic LaTiO{sub 3} nanocomposites (with space group Pbnm). In this work we identified that the monoclinic perovskite La{sub 2}Ti{sub 2}O{sub 7} with space group P2{sub 1} transforms its structure into one with the orthorhombic space group Cmc2{sub 1} at approximately 1073 K. The microstructure associated consisted of flaky monoclinic La{sub 2}Ti{sub 2}O{sub 7} nanocomposites in comparison with round-shaped LaTiO{sub 3} nanocomposites. - Highlights: • The flaky-like La{sub 2}Ti{sub 2}O{sub 7} compound was synthesized by sol–gel acrylamide route. • Simultaneous monitoring of the DTA and XRD with temperature was performed. • Phase transformation characterization of La{sub 2}Ti{sub 2}O{sub 7} has been carried out. • The variation of the La{sub 2}Ti{sub 2}O{sub 7} and LaTiO{sub 3} grain morphology has been compared.

36 MATERIALS SCIENCE↗

Predictive machine learning approaches for the microstructural behavior of multiphase zirconium alloys

Abstract Zirconium alloys are widely used in harsh environments characterized by high temperatures, corrosivity, and radiation exposure. These alloys, which have a hexagonal closed packed (h.c.p.) structure thermo-mechanically degrade, when exposed to severe operating environments due to hydride formation. These hydrides have a different crystalline structure, than the matrix, which results in a multiphase alloy. To accurately model these materials at the relevant physical scale, it is necessary to fully characterize them based on a microstructural fingerprint, which is defined here as a combination of features that include hydride geometry, parent and hydride texture and crystalline structure of these multiphase alloys. Hence, this investigation will develop a reduced order modeling approach, where this microstructural fingerprint is used to predict critical fracture stress levels that are physically consistent with microstructural deformation and fracture modes. Machine Learning (ML) methodologies based on Gaussian Process Regression, random forests, and multilayer perceptrons (MLP) were used to predict material fracture critical stress states. MLPs, or neural networks, had the highest accuracy on held-out test sets across three predetermined strain levels of interest. Hydride orientation, grain orientation or texture, and hydride volume fraction had the greatest effect on critical fracture stress levels and had partial dependencies that were highly significant, and in comparison hydride length and hydride spacing have less effects on fracture stresses. Furthermore, these models were also used accurately predicted material response to nominal applied strains as a function of the microstructural fingerprint.

36 MATERIALS SCIENCE↗

Identification of mechanisms driving heterogeneous void growth in ductile aluminum

Void growth plays a central role in ductile fracture, yet the specific mechanisms that control this remain obscure. Classical models, such as those proposed by Rice and Tracey in 1969, are able to capture average rates of void growth, but cannot capture the heterogeneity of individual void growth. Building on recent work, the present study employs laboratory-based diffraction contrast tomography and in-situ x-ray computed tomography to investigate the effect of grain structure and other microstructural factors on void growth in an Al-2219 alloy. Crystal plasticity finite element (CP-FE) modeling is used alongside experimental data to evaluate the contributions of local mechanical states, grain orientation, grain size, and neighboring microstructural features. No strong linear relationships are found with any of the considered descriptors and void growth rate. Potential complex nonlinear relationships are explored with the use of a random forest regression model, which identifies initial void volume, void aspect ratio, local normal stress state, local shear stress state, and local equivalent plastic strain (EQPS) as features that most improve void growth rate predictions. The combination of these analyses suggests that these features should be prioritized to improve models of void growth.

Diffraction contrast tomography (DCT)↗

Nanoindentation Investigation of Chloride-Induced Stress Corrosion Crack Propagation in an Austenitic Stainless Steel Weld

Transgranular chloride-induced stress corrosion cracking (TGCISCC) is a mounting concern for the safety and longevity of arc welds on austenitic stainless steel (AuSS) nuclear waste storage canisters. Recent studies have shown the key role of crystallography in the susceptibility and propagation of TGCISCC in SS weldments. Given that crystallography underlies mechanical heterogeneities, the mechanical-crystallographic relationship during TGCISCC growth must be understood. In this study, welded SS 304L coupons are loaded in four-point bend fixtures and then boiled in magnesium chloride to initiate TGCISCC. Nanoindentation mapping is paired with scanning electron microscopy (SEM) electron backscatter diffraction (EBSD) to understand the correlation between grain orientation, grain boundaries, and hardening from TGCISCC propagation. The nanoindentation hardness of individual grains is found to not be a controlling factor for TGCISCC propagation. However, intragranular hardness is generally highest immediately around the crack due to localized strain hardening at the crack tip. This work shows that nanoindentation techniques can be useful in understanding CISCC behaviors when paired with electron microscopy.

36 MATERIALS SCIENCE↗

Migration of grain boundaries and triple junctions in high-purity aluminum during annealing after slight cold rolling

Grain orientations and grain boundary migrations near triple junctions in a high purity aluminum were analyzed by electron back scattered diffraction. The results indicate that there are good correlations between the Schmid factors or Taylor factors and the misorientation values of point to original point in grains near the triple junctions in a slightly deformed sample. Grains with higher Schmid factors or lower Taylor factors typically correspond to higher misorientation values near the triple junctions. In a subsequent annealing at 400 °C, both grain boundaries and triple junctions migrate, but the former leave ghost lines. During such migration, a grain boundary grows from the grain with lower Schmid factor (higher Taylor factor) into the grain with higher Schmid factor (lower Taylor factor). Usually, the amount of migration of a grain boundary is considerably greater than that of a triple junction, and the grain boundary becomes more curved after migration. These observations indicate that the triple junctions have drag effects on grain boundary migration. - Highlights: • Polycrystalline aluminum with fine grains about 30 μm were used. • Off-line in situ EBSD was used to identify TJs before and after annealing. • Grains with higher SFs have higher misorientation values near TJs after deformation. • Grain boundaries grow from hard grains into soft grains during annealing. • Triple junctions have drag effects on grain boundaries migration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

An algorithm for resolving intragranular orientation fields using coupled far-field and near-field high energy $\mathrm{X}$-ray diffraction microscopy

Here, we present a novel algorithm for reconstructing spatial intragranular lattice orientation fields using both far-field and near-field high energy X-ray diffraction microscopy (HEDM) measurements. An established far-field indexing algorithm is modified to include lattice orientation distribution information (grain orientation envelopes) in addition to average grain orientations. The near-field data reduction algorithm utilizes this enriched far-field orientation data as a seed for reconstructing intragranular spatial maps of lattice orientation from the diffraction images. The primary benefit of the new algorithm is a significant decrease in the number of trial calculations that must be performed in the reconstruction process compared to existing methodologies while maintaining scalability. The resulting gains in efficiency facilitate the use of relatively modest computational resources and improve throughput at the point of measurement. We provide two example applications: volumetric orientation field reconstructions for a Ti-Al alloy both before and after the application of 3% uniaxial strain. The results showcase the efficiency of the new method and the ability to resolve subtle changes in microstructure, which are associated with incipient plastic deformation.

36 MATERIALS SCIENCE↗

New Structural Insight into Interface-Controlled α–σ Phase Transformation in Fe-Cr Alloys

Synchrotron Laue microdiffraction scanning is used for the ex situ study of the body-centered, cubic-to-tetragonal phase transformation that occurs in equiatomic polycrystalline Fe-Cr alloys at temperatures between 550 and 800 °C. Grain orientation and grain strains were scanned with a micron step resolution after annealing at 700 °C for 12 h. Further microstructural details on the early stage of the transformation, and more particularly on the cubic-to-tetragonal phase interface, were achieved. Only the α and ordered σ phases were detected. The crystallographic relationships at the interface between the two phases did not follow the predicted rules; this result is discussed in relation to the measured microstrains.

36 MATERIALS SCIENCE↗

BERT Non-Destructively Probes the Microstructure of Dissimilar Welds [Poster]

Energy-resolved neutron imaging (ERNI) utilizes contrast provided by diffraction. Microstructure with >100µm grains as in cast, annealed or welded materials is difficult to characterize by X-ray or electron-based methods $\Rightarrow$ Well-suited for neutron Bragg-edge radiography. BERT was applied to dissimilar welds of Inconel on steel produced by additive manufacturing. Viewing the sample at time-of-flight/energy/wavelength where a single grain orientation dominates the attenuation allows to map grain orientations. Similarly to electron-backscatter diffraction (EBSD) but on cm length scales and through-thickness. Combined with texture measurements on the HIPPO instrument, identifying major grain orientations, 2D and 3D grain orientation maps are feasible. Results can guide development of thermo-mechanical treatment avoiding or introducing such microstructures, characterize dissimilar welds, interpretation of acoustic signals for quality control, guide destructive examination with X-rays/electrons, or provide data for codes predicting such microstructures.

36 MATERIALS SCIENCE↗

Microstructure and texture evolution of deformed Mg-Zn alloy during recrystallization

Highlights: • The texture intensity in the Mg-Zn alloy relied on the microstructure. • Fine DRXed grains showed a fiber texture distributing between <10.0> and <11.0>. • Coarse DRXed grains mainly exhibited <11.0> fiber texture. • The preferred growth of <11.0> oriented grains resulted in texture evolution. - Abstract: The microstructure and texture evolution of Mg-Zn alloy during recrystallization was investigated by EBSD in the present study. Deformed region, fine DRXed region and coarse DRXed region were obtained in Mg-Zn alloy during deformation. It was found that the texture intensity in DRXed region was weaker compared with the deformed region. The second phase at grain boundaries resulted in the formation of fine DRXed grains with weaker texture compared with the coarse DRXed region. Additionally, a remarkable grain-size driven textural transition from <10.0>–<11.0> texture to <11.0> texture were detected with the growth of DRXed grains. The recrystallized grains with small grain size showed a fiber texture distributing homogeneously between <10.0> and <11.0>, while <11.0> fiber texture was predominant for the large recrystallized grains. It is suggested that <11.0> oriented grains grew faster than other oriented grains, which was ascribed to larger misorientation between <11.0> oriented grains and their neighboring grains.

36 MATERIALS SCIENCE↗

Technical Letter Report Assessment of Ultrasonic Phased Array Inspection Method for Welds in Cast Austenitic Stainless Steel Pressurizer Surge Line Piping JCN N6398, Task 1B

Research is being conducted for the U.S. Nuclear Regulatory Commission (NRC) at the Pacific Northwest National Laboratory (PNNL) to assess the effectiveness and reliability of advanced nondestructive examination (NDE) methods for the inspection of light water reactor components. The scope of this research encompasses primary system pressure boundary materials including cast austenitic stainless steels (CASS); dissimilar metal welds; piping with corrosion-resistant cladding; weld overlays, inlays and onlays; and far-side examinations of austenitic piping welds. A primary objective of this work is to evaluate various NDE methods to assess their ability to detect, localize, and size cracks in coarse-grained steel components. In this effort, PNNL supports cooperation with Commissariat à l’Energie Atomique (CEA) to assess reliable inspection of CASS materials. The NRC Project Manager has established a cooperative effort with the Institut de Radioprotection et de Surete Nucleaire (IRSN). CEA, under funding from IRSN, are supporting collaborative efforts with the NRC and PNNL. Regarding its work on the NDE of materials, CEA is providing its modeling software (CIVA) in exchange for PNNL offering expertise and data related to phased-array detection and sizing, acoustic attenuation, and back scattering on CASS materials. This collaboration benefits the NRC because CEA performs research and development on CASS for Électricité de France (EdF). This technical letter report provides a summary of a technical evaluation aimed at assessing the capabilities of phased-array (PA) ultrasonic testing (UT) methods as applied to the inspection of welds in CASS pressurizer (PZR) surge line nuclear reactor piping. A set of thermal fatigue cracks (TFCs) was implanted into three CASS PZR surge-line specimens (pipe-to-elbow welds) that were fabricated using vintage CASS materials formed in the 1970s, and flaw responses from these cracks were used to evaluate detection and sizing performance of the PA-UT methods applied. This effort was comprised of multiple elements that included use of microstructural knowledge (dimensional analysis, grain orientation, and grain type) as well as sound field modeling to more effectively modify inspection parameters and enhance the inspection outcomes. Advanced probe design and sound field simulations were employed to enhance detection and characterization of circumferentially oriented flaws, and an assessment of lateral (circumferential) flaw localization capability and performance was also conducted. An evaluation of flaw detection, length sizing, depth sizing, and signal-to-noise ratio was performed for all flaws in the subject specimens, as a function of various inspection parameters, and finally, measurements were made to quantify and assess the baseline CASS material noise and its potential impact on flaw detection.

36 MATERIALS SCIENCE↗

Characterization of Large Grain Nb Ingot Microstructure Using OIM and Laue Methods

Large grain niobium is being examined for fabricating superconducting radiofrequency cavities as an alternative to using rolled sheet with fine grains. It is desirable to know the grain orientations of a niobium ingot slice before fabrication, as this allows heterogeneous strain and surface roughness effects arising from etching to be anticipated. Characterization of grain orientations has been done using orientation imaging microscopy (OIM), which requires destructive extraction of pieces from an ingot slice. Use of a Laue camera allows nondestructive characterization of grain orientations, a process useful for evaluating slices and deformation during the manufacturing process. Five ingot slices from CBMM, Ningxia, and Heraeus are compared. One set of slices was deformed into a half cell and the deformation processes that cause crystal rotations have been investigated and compared with analytical predictions. The five ingot slices are compared in terms of their grain orientations and grain boundary misorientations, indicating no obvious commonalities, which suggests that grain orientations develop randomly during solidification.

36 MATERIALS SCIENCE↗

Experimental study of microstructure changes due to low cycle fatigue of a steel nanocrystallised by Surface Mechanical Attrition Treatment (SMAT)

Electron Backscatter Diffraction technique is used to characterize the microstructure of 316L steel generated by Surface Mechanical Attrition Treatment (SMAT) before and after low cycle fatigue tests. A grain size gradient is generated from the top surface to the interior of the samples after SMAT so that three main regions can be distinguished below the treated surface: (i) the ultra-fine grain area within 5 μm under the top surface with preferably oriented grains, (ii) the intermediate area where the original grains are partially transformed, and (iii) the edge periphery area where the original grains are just mechanically deformed with the presence of plastic slips. Fatigue tests show that cyclic loading does not change the grain orientation spread and does not activate any plastic slip in the ultra-fine grain top surface area induced by SMAT. On the opposite, in the plastically SMAT affected region including the intermediate area and the edge periphery area, new slip systems are activated by low cycle fatigue while the grain orientation spread is increased. These results represent a first very interesting step towards the characterization and understanding of mechanical mechanisms involved during the fatigue of a grain size gradient material. - Highlights: •LCF tests are carried out on specimens processed by SMAT. •EBSD is used to investigate microstructural changes induced by LCF. •A grain size gradient is generated by SMAT from surface to the bulk of the fatigue samples. •New slip systems are activated by LCF and GOS is increased in plastically deformed region. •However, these phenomena are not observed in the top surface ultra-fine grain area.

36 MATERIALS SCIENCE↗

CosTuuM: Polarized Thermal Dust Emission by Magnetically Oriented Spheroidal Grains

We present the new open-source C++-based Python library CosTuuM that can be used to generate infrared absorption and emission coefficients for arbitrary mixtures of spheroidal dust grains that are (partially) aligned with a magnetic field. We outline the algorithms underlying the software, demonstrate the accuracy of our results using benchmarks from literature, and use our tool to investigate some commonly used approximative recipes. We find that the linear polarization fraction for a partially aligned dust grain mixture can be accurately represented by an appropriate linear combination of perfectly aligned grains and grains that are randomly oriented, but that the commonly used picket fence alignment breaks down for short wavelengths. We also find that for a fixed dust grain size, the absorption coefficients and linear polarization fraction for a realistic mixture of grains with various shapes cannot both be accurately represented by a single representative grain with a fixed shape, but that instead an average over an appropriate shape distribution should be used. Insufficient knowledge of an appropriate shape distribution is the main obstacle in obtaining accurate optical properties. CosTuuM is available as a standalone Python library and can be used to generate optical properties to be used in radiative transfer applications.

79 ASTRONOMY AND ASTROPHYSICS↗

Isothermal annealing behaviour of nuclear grade 20Cr-25Ni austenitic stainless steel

Highlights: • At 930 °C recrystallisation of deformed 20/25 Nb steel is completed after 120 s. • Recrystallisation proceeds by strain induced boundary migration. • An increase of cube oriented grains at the expense of S oriented is observed. • The boundary migration induced the precipitation of niobium carbides. • The grain size is limited by the particle dispersion according to Zener pinning. - Abstract: We have performed an in-depth characterisation of the microstructure evolution of 20Cr-25Ni Nb-stabilised austenitic stainless steel during isothermal annealing at 930 °C using scanning and transmission electron microscopy. This steel grade is used as cladding material in advanced gas-cooled fission reactors, due to its resistance to thermal creep and water corrosion. The initial deformed microstructure undergoes recrystallisation via a strain-induced boundary migration mechanism, attaining a fully recrystallised microstructure after 120 s of annealing. The transition from low-to-high grain boundaries has already occurred after 15 s, together with an increase in the cube grain orientation at the expense of the S texture component. After 120 s, the grain boundary migration induces the formation of new fine Nb(C,N) particles, whereas the pre-existing particles become enriched in Ni and Si. The resulting particle population limits the grain growth in the austenitic matrix, based on the Zener pinning model, resulting in relatively small recrystallised austenite grains and a high density of high-angle and special coincidence-lattice-site grain boundaries, together with a large number of particle/matrix interfaces.

36 MATERIALS SCIENCE↗

Microstructure and texture evolution of friction stir lap welded dissimilar multi-aluminum stack

Here this work investigates the microstructural evolution of a dissimilar multiple-aluminum alloy stack (AA7055, AA7055, AA6022) produced by friction stir lap welding (FSLW). A through-thickness analyses of grain orientation map, grain size and distribution, strain distribution, and texture evolution by electron backscattered diffraction-based characterization technique were performed. Two different welding parameters (combination of tool rotation and traverse speed) were used to study the effects of the welding parameters on these microstructural characteristics. The study shows that higher welding speed and higher rotation speed of the FSLW tool yield finer grains. FSLW resulted in shear texture formation in the weld regions due to high welding speeds. This texture development in the nugget zone is consistent with shear deformation, and (111) pole figures show ideal shear texture components. The Stir Zone (SZ) exhibits shear texture (A/A ̅ and B/B ̅ components), consistent with other shear-assisted processes. Recrystallization mechanisms observed are CDRX in SZ and DDRX in TMAZ (Thermo-Mechanically Affected Zone). Interface analysis reveals the presence of oxide layers between different aluminum sheets, affecting joint mechanical performance. The mechanical property of the lap welded joints was presented in terms of microhardness distribution across the weld cross section. Slightly higher hardness in higher speed welding setup was observed throughout the SZ and AA6022 layer, indicating greater grain refinement and uniform grain structure distribution.

36 MATERIALS SCIENCE↗

Investigation of deformation mechanisms in an advanced FeCrAl alloy using in-situ SEM-EBSD testing

The deformation mechanisms associated with uniaxial tensile testing are observed by conducting tensile experiments of an FeCrAl alloy using scanning electron microscopy (SEM) coupled with electron backscattered diffraction (EBSD). Prior to the deformation, investigated alloy was consisting grain and precipitate size of ~63.0 μm and ~6.7 μm, respectively. The recorded SEM micrographs and EBSD data at increasing levels of strains revealed the complex phenomena of slip bands’ formation in the presence of surface grain morphology evolution and their (001), (110) and (111) crystallographic planes distortions. The grains with orientation (110)||tensile direction (TD) shows higher shape change; however, (001)||TD and (111)||TD oriented grains show higher lattice gradient formation. Extracted information from the EBSD indicates that the crystallographic rotations drive towards specific, fiber-like texture in relation to the loading direction. Postmortem analysis of the recorded microstructure during the tensile deformation explains the phenomena of crack formation in the hard-intermetallic particles before the ultimate tensile strength (UTS). However, after the UTS, pores were identified in the neck that resulted from extensive plastic deformation. In-depth analysis was carried out to identify the cause of cracks and pores formation phenomena during the tensile test.

36 MATERIALS SCIENCE↗

Phase-field framework with constraints and its applications to ductile fracture in polycrystals and fatigue

Abstract Modeling of ductile fracture in polycrystalline structures is challenging, since it requires integrated modeling of cracks, crystal plasticity, and grains. Here we extend the typical phase-field framework to the situations with constraints on the order parameters, and formulate two types of phase-field models on ductile fracture. The Type-I model incorporates three sets of order parameters, which describe the distributions of cracks, plastic strain, and grains, respectively. Crystal plasticity is employed within grain interiors accommodated by J 2 plasticity at grain boundaries. The applications of the Type-I model to single crystals and bicrystals demonstrate the influences of grain orientations and grain boundaries on crack growth. In the Type-II model, J 2 plasticity is assumed for the whole system and grain structures are neglected. Taking advantage of the efficiency of the fast Fourier transform, our Type-II model is employed to study low cycle fatigue. Crack closure and striation-like patterning of plastic strain are observed in the simulations. Crack growth rate is analyzed as a function of the J -integral, and the simulated fatigue life as a function of plastic strain agrees with the Coffin–Manson relation without a priori assumption.

36 MATERIALS SCIENCE↗