Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Anisotropic grain boundary area and energy distributions in tungsten

Describing microstructure evolution in tungsten requires a quantitative description of the anisotropic grain boundary energy. Here we present a grain boundary energy function for tungsten that specifies the energy of an arbitrary boundary given its five macroscopic crystallographic parameters. A comparison of measured grain boundary areas and the grain boundary energies given by the function at the Σ11, Σ17b, and Σ33a misorientations, which are problematic to determine by measurement or atomistic calculations, reveals inverse correlations that are similar to what have been observed in other metals.

36 MATERIALS SCIENCE↗

On the role of precursor powder composition in controlling microstructure, flux pinning, and the critical current density of Ag/Bi$_2$Sr$_2$CaCu$_2$O$_x$ conductors

Precursor powder composition is known to strongly affect the critical current density (J c ) of Ag/Bi$_2$Sr$_2$CaCu$_2$O$_x$ (Bi-2212) wires. However, reasons for such J c dependence have not yet been fully understood, compromising our ability to achieve further optimization. In this paper, we systematically examined superconducting properties, microstructural evolution and phase transformation, and grain boundaries of Bi-2212 conductors fabricated from precursor powders with a range of compositions using a combination of transport-current measurements, a quench technique to freeze microstructures at high temperatures during heat treatment, and scanning transmission electron microscopy (STEM). Samples include both dip-coated tapes and round wires, among which a commercial round wire carries a high J c of 7600 A mm -2 at 4.2 K, self-field and 2600 A mm -2 at 4.2 K, 20 T, respectively. In the melt, this high-J c conductor, made using a composition of Bi 2.17 Sr 1.94 Ca 0.89 Cu 2 O x , contains a uniform dispersion of fine alkaline-earth cuprate (AEC) and copper-free solid phases, whereas several low-J c conductors contain large AEC particles. Such significant differences in the phase morphologies in the melt are accompanied by a drastic difference in the formation kinetics of Bi-2212 during recrystallization cooling. STEM studies show that Bi-2212 grain colonies in the high-J c conductors have a high density of Bi 2 Sr 2 CuO y (Bi-2201) intergrowths, whereas a low-J c conductor, made using Bi 2.14 Sr 1.66 Ca 1.24 Cu 1.96 O x , is nearly free of them. STEM investigation shows grain boundaries in low-J c conductors are often insulated with a Bi-rich amorphous phase. Finally, high-J c conductors also show higher flux-pinning strength, which we ascribe to their higher Bi-2201 intergrowth density.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructural stability of wrought, laser and electron beam glazed NARloy-Z alloy at elevated temperatures

Microstructure of wrought, laser, and electron-beam glazed NARloy-Z(Cu-3 wt.% Ag-0.5 wt.% Zr) was investigated for thermal stability at elevated temperatures (539 to 760 C (1,100 to 1,400 F)) up to 94 h. Optical and scanning electron microscopy and electron probe microanalysis were employed for studying microstructural evolution and kinetics of precipitation. Grain boundary precipitation and precipitate free zones (PFZ's) were observed in the wrought alloy after exposing to temperatures above 605 C (1,120 F). The fine-grained microstructure observed in the laser and electron-beam glazed NARloy-Z was much more stable at elevated temperatures. Microstructural changes correlated well with hardness measurements.

Singh, J.↗

Laser Additive Manufacturing of F/M Steels for Radiation Tolerant Nuclear Components

According to the Nuclear Energy R&D Roadmap Report submitted to Congress in 2010, one the key challenges facing the nuclear energy industry involves development of new reactor designs with reduced capital costs. Two related R&D objectives outlined in the report include: 1) Making improvements in the affordability of new reactors; and 2) Development of structural materials to withstand irradiation for longer periods. Laser additive manufacturing (LAM) is particularly well suited for more rapid and economical fabrication of reactor components relative to current fabrication methods. The proposed work involving LAM directly addresses the two R&D objectives outlined above relevant to the pertinent mission problems. The classical Materials Science approach involving development of Process/Structure/Property/Performance (P/S/P/P) relations was employed in this project. Processing included LAM and heat-treating. Thermal cycling during LAM is discussed here, and phase diagrams and continuous cooling transformation (CCT) diagrams are used to rationalize microstructural evolution. Structures were characterized including grain size & morphology, volume fraction, morphology, composition and location of carbides in as-deposited and heat-treated conditions. In the simplest sense, the goal was to control microstructures through process manipulation with a view toward optimizing properties and performance in service.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Microstructure evolution and mechanical behavior of a high strength dual-phase steel under monotonic loading

Transmission electron microscopy (TEM) microstructures of a high-strength dual-phase steel DP800 have been examined after moderate plastic deformations in simple shear and uniaxial tension. Special attention has been paid to the effect of the intergranular hard phase (martensite) on the microstructure evolution in the near-grain boundary regions. Quantitative parameters of dislocation patterning have been determined and compared with the similar characteristics of previously examined single-phase steels. The dislocation patterning in the interiors of the ferrite grains in DP800 steel is found to be similar to that already observed in the single-phase IF (Interstitial Free) steel whereas the martensite-affected zones present a delay in patterning and display very high gradients of continuous (gradual) disorientations associated with local internal stresses. The above stresses are shown to control the work-hardening of dual-phase materials at moderate strains for monotonic loading and are assumed to influence their microstructure evolution and mechanical behavior under strain-path changes. - Highlights: • The microstructure evolution has been studied by TEM in a DP800 steel. • It is influenced by both martensite and dislocations in the initial state. • The DP800 steel presents a high work-hardening rate due to internal stresses.

36 MATERIALS SCIENCE↗

Microstructure and Strengthening Mechanisms in an Ultrafine Grained Al-Mg-Sc Alloy Produced by Powder Metallurgy

Additions of Sc to an Al-Mg matrix were investigated, paying particular attention to the influence of Al3Sc precipitates and other dispersoids, as well as grain size, on mechanical behavior. Prior studies have shown that Sc significantly increases the strength of coarse-grained Al-Mg alloys. Prompted by these findings, we hypothesized that it would be of fundamental and technological interest to study the behavior of Sc additions to an ultrafine-grained (UFG) microstructure (e.g., 100’s nm). Accordingly, we investigated the microstructural evolution and mechanical behavior of a cryomilled ultrafine grained Al-5Mg-0.4Sc (wt pct) and compared the results to those of an equivalent fine-grained material (FG) produced by powder metallurgy. Experimental materials were consolidated by hot isostatic pressing (HIP’ing) followed by extrusion or dual mode dynamic forging. Under identical processing conditions, UFG materials generate large Al3Sc precipitates with an average diameter of 154 nm and spaced approximately 1 to 3 µm apart, while precipitates in the FG materials have a diameter of 24 nm and are spaced 50 to 200 nm apart. The strengthening mechanisms are calculated for all materials and it is determined that the greatest strengthening contributions for the UFG and FG materials are Mg-O/N dispersion strengthening and precipitate strengthening, respectively.

36 MATERIALS SCIENCE↗

Phase-field modeling of stored-energy-driven grain growth with intra-granular variation in dislocation density

Abstract We present a phase-field (PF) model to simulate the microstructure evolution occurring in polycrystalline materials with a variation in the intra-granular dislocation density. The model accounts for two mechanisms that lead to the grain boundary migration: the driving force due to capillarity and that due to the stored energy arising from a spatially varying dislocation density. In addition to the order parameters that distinguish regions occupied by different grains, we introduce dislocation density fields that describe spatial variation of the dislocation density. We assume that the dislocation density decays as a function of the distance the grain boundary has migrated. To demonstrate and parameterize the model, we simulate microstructure evolution in two dimensions, for which the initial microstructure is based on real-time experimental data. Additionally, we applied the model to study the effect of a cyclic heat treatment (CHT) on the microstructure evolution. Specifically, we simulated stored-energy-driven grain growth during three thermal cycles, as well as grain growth without stored energy that serves as a baseline for comparison. We showed that the microstructure evolution proceeded much faster when the stored energy was considered. A non-self-similar evolution was observed in this case, while a nearly self-similar evolution was found when the microstructure evolution is driven solely by capillarity. These results suggest a possible mechanism for the initiation of abnormal grain growth during CHT. Finally, we demonstrate an integrated experimental-computational workflow that utilizes the experimental measurements to inform the PF model and its parameterization, which provides a foundation for the development of future simulation tools capable of quantitative prediction of microstructure evolution during non-isothermal heat treatment.

Materials Science↗

Microstructural evolution and hardness response in the laser beam welded joints of pure titanium during recrystallization and grain growth

Highlights: • The LABs and high local misorientations indicate the existence of plastic strains in the as-welded HAZ and FZ. • During heat treatment the recrystallization occurs in the HAZs, decreasing plastic strains, but it doesn't appear in the FZs. • The coarse and unstrained grains gradually replace the fine and strained ones in the HAZs during recrystallization. • The decrease of plastic strains in the HAZs during recrystallization causes the descent of average hardness values based on the strain strengthening. - Abstract: Microstructural evolution and hardness response in the laser beam welded joints of pure titanium during recrystallization and grain growth were investigated by means of electron backscatter diffraction and hardness measurement. The low-angle boundaries (LABs) and high local misorientations, in the as-welded heat affected zone (HAZ) and fusion zone (FZ), indicate the existence of plastic strains caused by the plastic strains due to the thermal stress and the non-equilibrium phase transformations. The recrystallization occurs in the HAZs during heat treatment, but the grain growth after recrystallization does not appear under the heat treatment conditions. Moreover as a result of the slightly high impurity contents in the as-welded FZ, no distinct recrystallization is found in the FZs in this work. During recrystallization in the HAZs, the coarse and unstrained grains with equiaxed shape and smooth boundary gradually consume the fine and strained ones with irregular shape and serrate boundary. Meanwhile, the LABs disappear and the low local misorientations replace the high ones in the modified grains. The recrystallization during heat treatment causes the decrease of plastic strains in the HAZs, which reflects on the descent of average hardness values based on the strain strengthening.

36 MATERIALS SCIENCE↗

Evolution of microstructure and strength of a high entropy alloy undergoing the strain-induced martensitic transformation

In a recent work, we have reported outstanding strength and work hardening exhibited by a metastable high entropy alloy (HEA), Fe 42 Mn 28 Co 10 Cr 15 Si 5 (in at. %), undergoing the strain-induced martensitic transformation from metastable gamma austenite (γ) to stable epsilon martensite (ε). However, the alloy exhibited poor ductility, which was attributed to the presence of the brittle sigma (σ) phase in its microstructure. The present work reports the evolution of microstructure, strength, and ductility of a similar HEA, Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 (in at. %), designed to suppress the formation of σ phase. A cast and then rolled plate of the alloy was processed into four conditions by annealing for 10 and 30 min at 1100 °C and by friction stir processing (FSP) at tool rotation rates of 150 and 400 revolutions per minute (RPM) to facilitate detailed examinations of variable initial grain structures. Neutron diffraction and electron microscopy were employed to characterize the microstructure and texture evolution. The initial materials had variable grain size but nearly 100% γ structure. Diffusionless strain induced γ→ε phase transformation took place under compression with higher rate initially and slower rate at the later stages of deformation, independent on the initial grain size. The transformation facilitated part of plastic strain accommodation and rapid strain hardening owing to a transformation-induced dynamic Hall-Petch-type barrier effect, increase in dislocation density, and texture. Here, the peak strength of nearly 2 GPa was achieved under compression using the structure created by double pass FSP (150 RPM followed by 150 RPM). Remarkably, the tensile elongation exhibited by the alloy was nearly 20% with fracture surfaces featuring a combination of ductile dimples and cleavage.

36 MATERIALS SCIENCE↗

Ion-induced grain growth and texturing in refractory thin films-A low temperature process

Selective grain growth can be promoted in thin films independently of the materials intrinsic properties, such as the melting temperature, by ion-irradiation. This enables the previously impossible evolution of large grain-sized microstructures with controlled crystallographic textures even in refractory metals, such as {alpha}-tantalum. Experimental results from materials with different crystal structure are compared on the basis of a theoretical model, which reveals the differences in ion-induced grain-growth dynamics.

36 MATERIALS SCIENCE↗

The Effect of Process History on Grain Boundaries and Dislocation Substructures on Functional Properties of Nb for SRF Cavities: Plastic Formability and Microstructural Evolution. Final report

While much progress has been made in improving the performance of cavities in the past decade, reproducible performance remains elusive. This renewal of “The cost of grain boundaries on the performance of superconducting cavities” examines in further depth the interactions between forming and annealing processes and functional performance at the scale of dislocation substructure and grain boundaries. There are five tasks identified in the renewal, which are: Characterization / analysis of current cavity technology: Effect of deformation, heat treatment, surface treatments, and residual damage on cavity function (Lee and Bieler) Characterization of dislocation mechanisms in single and bicrystals (Bieler) Quantifying effects of impurities and deformation mechanisms in Nb using density functional theory calculations (Solanki) Crystal plasticity constitutive model development (Pourboghrat and Eisenlohr) Modeling and measuring thermal conductivity in thin layers (Wright)

36 MATERIALS SCIENCE↗

Texture evolution and their effects on the mechanical properties of duplex Mg-Li alloy

Texture evolution is strongly dependent on the deformation mode during thermo-mechanical treatments. In this paper, we report the texture evolution in a duplex Mg-Li alloy. The results provide an evidence of deformation mode transition in the hexagonal-close-packed (hcp) alpha phase with various thickness reductions. The activation sequence of deformation modes is basal slip first, and then pyramidal slip during hot-rolling to a thickness reduction of 40%. The relative activity of slip decreases with further thickness reduction. After annealing, basal texture is strengthened and pyramidal component disappears due to static recrystallization and grain growth. The microstructure, specifically texture evolution in both hcp alpha and body-centered cubic (bcc) beta phase and their effects on mechanical properties are quantitatively analyzed and assessed. (C) 2016 Elsevier B.V. All rights reserved.

36 MATERIALS SCIENCE↗

Pre-compression effect on microstructure evolution of extruded pure polycrystalline magnesium during reversed tension load

Highlights: • Number of twin variants under compression along ED is dependent on grain orientation. • Tension after pre-compression results in low-SF twinning and secondary twinning. • Secondary twinning is facilitated by increasing pre-compression. • Sub-grains due to twinning enhance material strength. - Abstract: The microstructure evolution of extruded pure polycrystalline magnesium under compression followed by subsequent tension in ambient air was investigated. Solid round dog-bone shaped specimens were compressed along the extrusion direction (ED) to − 7.3% and − 12.8% true strains, respectively, and then tensioned along the ED to failure. Electron backscatter diffraction (EBSD) was used to examine the microstructure evolution using companion specimens unloaded at multiple points along the deformation curves. Pre-compression along the ED resulted in {10 1-bar 2} tension twinning which increased in volume with increasing strain until exhaustion at approximately − 10.5% true strain. Tensile reloading of the pre-compressed specimens led to a combination of low Schmid factor twinning, detwinning, and secondary {10 1-bar 2} tension twinning. Detwinning was more significant than secondary twinning in the − 7.3% pre-compressed specimens, where only one secondary twin variant was observed. {10 1-bar 2} secondary twinning was more significant in the − 12.8% pre-compressed specimens, where up to three secondary twin variants were observed. After complete detwinning of primary twins, the secondary twins were retained and appeared as sub-grains. The residual sub-grains resulted from secondary twinning may provide a strengthening mechanism for wrought Mg alloys.

36 MATERIALS SCIENCE↗

Identifying multiple synergistic factors on the susceptibility to stress relaxation cracking in variously heat-treated weldments

The 347H austenitic stainless steel has been widely used for pressure vessels and pipeline (PVP) applications due to its excellent creep and corrosion resistance, which fit ideally to the harsh conditions in petrochemical industries, fossil fuel or nuclear power plants, and modern energy storages. However, a failure mode has been commonly observed with cracks emerging at the heat affected zone (HAZ) of weldments during post-weld heat treatment (PWHT) or under intermediate to high temperature service conditions. This phenomenon is termed as Stress Relaxation Cracking (SRC) since the purpose of PWHT is to relieve the welding-induced residual stress fields, or as Stress Age Cracking (SAC) if failure happens during service. A leading literature explanation of this failure suggests that the residual stress relaxation and the precipitation dissolution and/or re-precipitation occur in the same temperature range, which can lead to locally high strains and thus to crack at the grain boundaries. Since in situ spatial measurements of residual stress fields, microstructural evolution, and failure processes are nearly infeasible, this work recourses to a micromechanical finite element framework that models the high temperature failure as the nucleation and growth of grain boundary cavities, whereas various parameters such as thermomechanical loading history and its evolution, the competition of grain-interior dislocation creep and grain-boundary diffusion in failure lifetime, and microstructural heterogeneities (such as the precipitate free zone near grain boundaries) can be quantitatively incorporated. It can be concluded from these microstructure-explicit simulations that an accurate knowledge of residual stress evolution and a carefully calibrated set of material constitutive parameters are the essential prerequisites for lifetime predictions. The understanding of individual governing factors also leads to a mechanistic interpretation of the observed SRC susceptibility C-curves. In conclusion, these results suggest that the criticality of residual stress evolution, but not the precipitation-induced local strains, be the leading factor for SRC.

347H stainless steel weldments↗

In Situ Transmission Electron Microscopy of High-Temperature Inconel-625 Corrosion by Molten Chloride Salts

This paper describes an approach to monitor high temperature molten chloride (MgCl 2 -NaCl-KCl) salt corrosion of Inconel-625 alloy in real time at high spatial resolution. The approach is based on a micro-environmental-cell assembly integrated into a transmission-electron-microscope goniometer to examine in situ the salt-alloy interface during corrosion, employing real time electron diffraction and imaging. It establishes procedures to minimize incorporation of H 2 O or O 2 from atmosphere in the chloride salts during sample fabrication and corrosion, which is critical to understanding the fundamental corrosion mechanisms. A clustering algorithm and a 2D Gaussian fit function are used to determine diffraction spot intensities in in situ diffraction patterns, to quantify alloy corrosion. This facilitates quantitative observation of the evolution of individual grains, in contrast to conventional macroscopic corrosion rate quantification. The isothermal corrosion rate of Inconel-625 in an anhydrous, unoxidized salt-stack is 220 ± 30 μm year -1 at 700 °C and 350 ± 20 μm year -1 at 800 °C. However, the corrosion rate at 700 °C increases five-fold to 1000 ± 170 μm year -1 when the salt stack is air-exposed, indicating the dominant effects of hydrated or oxidized impurities on corrosion acceleration. Furthermore, real time imaging of the microstructure evolution suggests that corrosion is initiated at grain boundaries.

14 SOLAR ENERGY↗

Linking Initial Microstructure to ORR Related Property Degradation in SOFC Cathode: A Phase Field Simulation

Microstructure evolution driven by thermal coarsening is an important factor for the loss of oxygen reduction reaction rates in SOFC cathode. In this work, the effect of an initial microstructure on the microstructure evolution in SOFC cathode is investigated using a recently developed phase field model. Specifically, we tune the phase fraction, the average grain size, the standard deviation of the grain size and the grain shape in the initial microstructure, and explore their effect on the evolution of the grain size, the density of triple phase boundary, the specific surface area and the effective conductivity in LSM-YSZ cathodes. It is found that the degradation rate of TPB density and SSA of LSM is lower with less LSM phase fraction (with constant porosity assumed) and greater average grain size, while the degradation rate of effective conductivity can also be tuned by adjusting the standard deviation of grain size distribution and grain aspect ratio. The implication of this study on the designing of an optimal initial microstructure of SOFC cathodes is discussed.

25 ENERGY STORAGE↗

Microstructural and chemical evolution near anode triple phase boundary in Ni/YSZ solid oxide fuel cells

In this study, we report the micro-structural and chemical evolution of anode grain boundaries and triple phase boundary (TPB) junctions of Ni/YSZ anode supported solid oxide fuel cells. A NiO phase was found to develop along the Ni/YSZ interfaces extending to TPBs in the operated cells. The thickness of the NiO ribbon phase remains constant at ~ 5 nm in hydrogen for operating durations up to 540 h. When operating on synthesis gas, an increase in interphase thickness was observed from ~ 11 nm for 24 h of operation to ~ 51 nm for 550 h of operation. YSZ phases are observed to be stable in H{sub 2} over 540 h of operation. However, for the cell operated in syngas for 550 h, a 5–10 nm tetragonal YSZ (t-YSZ) interfacial layer was identified that originated from the Ni/YSZ interfaces. Yttrium species seem to segregate to the interfaces during operation, leading to the formation of t-YSZ in the Y-depleted regions.

Anode↗