Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain refinement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Microstructure, Hardness, and Residual Stress of the Dissimilar Metal Weldments of SA508-309L/308L-304L

A dissimilar metal weldment consisting of SA508-309L-308L-304L is widely used in light-water nuclear reactors. These weldments demonstrate dissimilar susceptibility to stress corrosion cracking that are related to the microstructure, properties, and residual stress. In this work, microstructures, hardness, and the residual stress distribution of the dissimilar metal weldments were investigated, with the correlation of increased hardness in the heat-affected zone (HAZ) to the microstructure. 304L HAZ demonstrated similar grain morphology as the base material, and the increase in hardness was primarily attributed to the increased dislocation density. SA508 HAZ demonstrated a change of grain morphology resulting from the different peak temperatures and cooling rates. The increased hardness in the SA508 HAZ was attributed to the refined grain morphology, higher dislocation density, and higher number density of precipitates. A ~ 20–30-μm-wide martensitic zone formed at the fusion boundary of SA508-309L, where Cr-rich carbide precipitates were observed, with the average size and the number density of 44.1 ± 16.9 nm and 1.5 × 10 21 m ₋3 , respectively. In conclusion, residual stress results demonstrated the largest tensile stress at 309L butter, indicating its high cracking susceptibility.

36 MATERIALS SCIENCE↗
NASA NTRS1988

The influence of grain size and composition on 1000 to 1400 K slow plastic flow properties of NiAl

The compressive slow plastic flow behavior of several B2 crystal structure NiAl intermetallics has been studied in air between 1000 and 1400 K. Small grain-sized Ni-48.25 at. pct Al (of about 10 microns) was found to be stronger than the previously studied 17 microns diameter material. While grain refinement improved the strength at all test temperatures, the exact mechanism is not clear. Experiments at lower temperature revealed that composition as well as grain size can be an important factor, since Ni-49.2Al was weaker than Ni-48.25Al. Pronounced yield points were found during slow strain-rate testing at 1000 K; however, continued deformation appears to take place by the same mechanism(s) as found at high temperatures. Small changes in thermomechanical processing (TMP) schedules to fabricate Ni-49.2Al indicated that basic deformation characteristics (stress exponent and activation energy) are not affected; however, the preexponential term could be modified if TMP alters the grain structure.

Whittenberger, J. Daniel↗
DOE OSTI2026

Influence of rolling reduction and annealing on recrystallization and grain structure in Ta-2.5W alloys

The microstructural evolution of wrought Tantalum - 2.5 wt% Tungsten (Ta-2.5W) alloys during thermomechanical processing is critical for optimizing their mechanical reliability in demanding applications such as aerospace, chemical processing, and nuclear technology. Despite the widespread use of Ta-W alloys, a comprehensive understanding of how rolling reduction, annealing temperature, and elemental inhomogeneity interact to determine recrystallization behavior and grain refinement remains incomplete. Here, in this study, we systematically investigate the effects of cold rolling and subsequent annealing on the microstructure of Ta-2.5W, with particular attention to grain orientation, stored energy, and elemental banding. Our results demonstrate that higher rolling reduction rates lower the onset and completion temperatures for recrystallization, resulting in finer and more homogeneous grain structures. Electron backscatter diffraction (EBSD) analysis reveals that grains with a 〈111〉 parallel to the plate normal possess higher stored energy and nucleate recrystallization more readily than grains with a 〈001〉 parallel to the plate normal. Elemental mapping shows that tungsten inhomogeneity leads to localized bands of accelerated recrystallization and hardness variation. These findings provide new insights into the mechanisms of microstructure refinement in Ta-2.5W alloys, offering guidance for tailoring processing routes to achieve superior performance in demanding engineering environments.

Annealing↗
DOE OSTI2022

Spall damage mechanisms in laser powder bed fabricated stainless steel 316L

This paper reports on spall damage mechanisms in laser powder bed fusion (LPBF) fabricated stainless steel 316L (SS316L) subjected to uniaxial, strain plate-impact loading and explores failure evolution with increasing impact velocity and peak pressure. Analysis of velocimetry profiles reveals a heterogeneous failure response with several different failure mechanisms activated during impact and resulting spall. The analysis is supported by optical microscopy and electron backscattered diffraction (EBSD) observation of soft recovered impacted samples, which show evidence of localized nano-twinning, twin growth, severe grain rotation, and grain refinement along the spall plane, in addition to pore nucleation, coalescence, and growth. Furthermore, the observed failure mechanisms, including crack formation and propagation along high angle grain boundaries (HAGBs), are not consistently indicative of ductile fracture typical of wrought stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A quinary WTaCrVHf nanocrystalline refractory high-entropy alloy withholding extreme irradiation environments

In the quest of new materials that can withstand severe irradiation and mechanical extremes for advanced applications (e.g. fission & fusion reactors, space applications, etc.), design, prediction and control of advanced materials beyond current material designs become paramount. Here, through a combined experimental and simulation methodology, we design a nanocrystalline refractory high entropy alloy (RHEA) system. Compositions assessed under extreme environments and in situ electron-microscopy reveal both high thermal stability and radiation resistance. We observe grain refinement under heavy ion irradiation and resistance to dual-beam irradiation and helium implantation in the form of low defect generation and evolution, as well as no detectable grain growth. The experimental and modeling results—showing a good agreement—can be applied to design and rapidly assess other alloys subjected to extreme environmental conditions.

36 MATERIALS SCIENCE↗
NASA NTRS1982

Recrystallization and grain growth in NiAl

Aluminide intermetallics, because of their strength, microstructural stability, and oxidation resistance at elevated temperatures, represent potential structural materials for use in advanced energy conversion systems. This inherent potential of the intermetallics can currently not be realized in connection with the general brittleness of the materials under ambient conditions. It is pointed out, however, that brittleness is not an inherent characteristic. Single crystals are ductile and polycrystals may be, too, if their grains are fine enough. The present investigation is concerned with an approach for reducing material brittleness, taking into account thermal-mechanically induced grain refinement in NiAl, a B2 aluminide which melts at 1638 C and which retains complete order to its melting point. Attention is given to the kinetics of recrystallization and grain growth of warm-worked, nickel-rich material.

Haff, G. R.↗
DOE OSTI2022

Analysis of contact conditions and microstructure evolution in shear assisted processing and extrusion using smoothed particle hydrodynamics method

Shear assisted processing and extrusion (ShAPE) is a solid-phase processing technique that adds an additional shear force as compared with a conventional extrusion approach. Recently, ShAPE has demonstrated the capability of extruding high-performance aluminum alloy 7075 (AA7075) tubes at speeds up to 12.2 m/min without surface tearing. However, the relationship among the ShAPE processing parameters, thermomechanical conditions, contact conditions, heat generation, and microstructure evolution remains primarily empirical because an insightful understanding of the associated physics is still lacking. To help elucidate these relationships, this work proposes a thermomechanical meshfree model for the first time for ShAPE processing of AA7075 using the smoothed particle hydrodynamics (SPH) method. The meshfree model is first validated thoroughly by experimental data in terms of material flow, die face temperature, and extrusion force with various processing parameters. The validated model is then used to analyze the steady-state contact conditions and heat generation rates during ShAPE processing. Distributions of the average grain size of AA7075 being extruded are calculated using the SPH model output. The meshfree model results reveal that extrusions conducted at lower temperatures and higher strain rates yield more refined grains and possibly higher material strength, which is also consistent with the experimental observations.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Effect of Li level, artificial aging, and TiB2 reinforcement on the fracture toughness of Weldalite (tm) 049-type alloys

Plane strain fracture toughness (K sub IC) was evaluated for Weldalite (tm) 049 with and without TiB2 reinforcement. For the nonreinforced variant, changes in toughness were measured for various aging conditions and lithium levels. Toughness testing was carried out on fatigue precracked compact tension (CT) specimens at 24 C, as per ASTM standard E-399. Toughness was measured as a function of aging time at 160 C for the two Weldalite 049(1.3) heats. The composition of these heats differed only in that 0.03 wt pct. Ti was added to one as an additional grain refiner. Both heats showed a decrease in toughness with increasing aging time, although toughness values for one were significantly higher than for the other. This greater toughness may be due to a subtle change in the grain size resulting for the presence of Ti or, alternatively, to differences in texture or substructure formed during extrusion.

Source record↗
DOE OSTI2025

A critical review of the history of fabricating monolithic U-Mo fuel plates

The fabrication of monolithic uranium-molybdenum alloy fuels, specifically those developed for high-performance research and test reactors, began in the early 2000s. The primary fuel form consists of uranium alloyed with 10-wt% molybdenum in a thin foil coated with zirconium and encapsulated in aluminum-6061 cladding. Over the years, the process has evolved with different types of casting, heat treatments, rolling schedules, and cladding applications. This review examines the history of these fabrication processes and their impact on microstructure and fuel-swelling performance. Even though various fabrication methods were used, we found little correlation between fabrication variation and fuel swelling. This insensitive relationship between fabrication variation and fuel swelling is primarily due to inhomogeneous microstructures that formed during casting and grain refinement that occurred during rolling. We conclude that the fabrication processes we examined produced similar microstructures, indicating that the fuel microstructure is somewhat insensitive to the fabrication parameters evaluated. However, the relatively small amount of historic data, such as those for grain sizes, limited this analysis. More recently fabricated materials, such as those from ongoing irradiation experiment, Mini-Plate-1 and Mini-Plate-2, were also excluded from this analysis and are intended to be reviewed separately. The findings, that fuel microstructure is somewhat insensitive to the fabrication parameters, do not imply that any fabrication method is acceptable, given the uncertainties in data and fuel-swelling observations. For example, only arc melting and vacuum induction melting casting processes were previously explored in the historic fabrication efforts. In conclusion, the findings should not be extrapolated to other casting processes.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Microstructural Transitions during Powder Metallurgical Processing of Solute Stabilized Nanostructured Tungsten Alloys

Exploiting grain boundary engineering in the design of alloys for extreme environments provides a promising pathway for enhancing performance relative to coarse-grained counterparts. Due to its attractive properties as a plasma facing material for fusion devices, tungsten presents an opportunity to exploit this approach in addressing the significant materials challenges imposed by the fusion environment. Here, we employ a ternary alloy design approach for stabilizing W against recrystallization and grain growth while simultaneously enhancing its manufacturability through powder metallurgical processing. Mechanical alloying and grain refinement in W-10 at.% Ti-(10,20) at.% Cr alloys are accomplished through high-energy ball milling with transitions in the microstructure mapped as a function of milling time. We demonstrate the multi-modal nature of the resulting nanocrystalline grain structure and its stability up to 1300 °C with the coarser grain size population correlated to transitions in crystallographic texture that result from the preferred slip systems in BCC W. Field-assisted sintering is employed to consolidate the alloy powders into bulk samples, which, due to the deliberately designed compositional features, are shown to retain ultrafine grain structures despite the presence of minor carbides formed during sintering due to carbon impurities in the ball-milled powders.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Enhancement in hard magnetic properties of (Nd, Pr)–Fe–B melt-spun ribbons

The coercivity of RE 2 Fe 14 B-type permanent magnets is strongly influenced by the microstructural features such as grain boundary (GB) phases as well as grain sizes. Here, we have combined micromagnetic simulations and experiments to elucidate the role of excess RE (Nd/Pr) in determining the resulting hard magnetic properties of Nd–Pr–Fe–B melt-spun ribbons. The intrinsic coercivity (H c ) at room temperature significantly enhanced from 9.7 kOe to 15.3 kOe with the increase in the Nd/Pr content. Furthermore, the effect of non-magnetic grain refining refractory carbide (TiC) on both the microstructure and magnetic hardening was studied. The addition of TiC showed a very high coercivity H c of up to 19.0 kOe at room temperature. Micromagnetic simulation indicates that the coercivity enhancement is mainly due to the reduction of inter-grain magnetic interaction, which is due to the RE-rich nonmagnetic grain boundary (GB) phase and/or TiC distributed at the GB. This work provides useful information on the roles of non-magnetic grain boundary phases for improving the coercivity of Nd–Pr–Fe–B magnets. Combined with experimental and modeling results, we have discussed the mechanism responsible for the enhancements in coercivity and the suitability of the alloys for high-performance permanent magnet development.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Report on use of Inoculants in Missile Application Alloys

This report documents the status of current inoculant research relevant to missile application alloys and MTCR control language. The information is intended to provide data on current inoculants for us determining the current state of development and identifying potential research directions. Although there has been significant scientific research into the development and synthesis of inoculants, their current availability is limited is traditional powder inoculants employed during casting processes. However, research continues the development of complex oxides, ribbon materials, high entropy alloys, and other inoculant product forms, including the use of inoculants in the melt pools produced during additive manufacturing. Research to date has focused primarily on aluminum and steel alloys with emphasis on refining grain structures and evolving equiaxed morphologies while increasing strength and castability. The primary inoculants in steel and cast irons include TiN, SiC, FeSi75, and Ce which have increased strength properties. Chief inoculants for Al alloys often include TiC, SiC, Al3Sc(x) and TiB2 to aid in precipitation and refinement. Ti and Ni alloys have fewer research activities involving inoculants, although TiN, TiB, ZrN and LaB6 (for Ti alloys) and WC, Co3FeNb2, and CrFeNb (for Ni alloys) have been used. Sic, Al2O3, Mg and Ti are key inoculants for Mg alloys. Multiple cast alloys from each of the material classes demonstrated increased strength and performance properties using inoculants, with several approaching requirements applicable to missile service environments. The continued evolution of advanced manufacturing capabilities is making it easier to produce high temperature near net shape structural materials using inoculant powders. These shapes may include the geometric shapes addressed within the MTCR (tubes and limited wall thicknesses). The use of inoculants may enable further development of high temperature alloys into near net shapes traditionally produced via casting processes due to limited ductility. This may decrease material and manufacturing costs. In addition, inoculation provides controlled kinetics and achievable chemical segregation that enables potential for far-from equilibrium thermodynamic microstructures and chemistries that could provide new metastable alloy states and subsequent properties to address co-design engineering constraints, including needs for increased strength and ductility. It is recommended that specific material combinations within these alloy classes be carefully watched as the materials evolve, with controls aimed at those having material properties above current MTCR levels. This specifically includes the use of refractory inoculants in alloys, and the application of inoculants in high strength and high temperature alloys via additive manufacturing processes, with care to link capabilities to product forms similar to the current requirements on tube geometries and material feed stocks. The continued development of nanoparticle inoculants will increase strength and ductility of high strength castings and additive manufactured metallic components. For example, adding inoculants into the casting of maraging steels and other precipitation strengthened alloys may drastically elevate mechanical properties above the control limit of current regulations.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Supercooling and structure of levitation melted Fe-Ni alloys

A study has been made of the effect of supercooling, quenching rate, growth inhibitors, and grain refiners on the structure of levitation-melted Fe- 25 pct Ni alloys. A combination of three morphologies, dendritic, spherical, and mixed dendritic and spherical, is observed in samples superheated or supercooled by less than 175 K. At larger supercooling, however, only the spherical morphology is observed. The grain size and the grain boundary shape are found to be strongly dependent on the subgrain morphology but not on the quenching temperature. Considerable grain growth is evident in samples with spherical and mixed morphologies but not in the dendriitic samples. The average cooling rates during solidification and the heat transfer coefficients at the metal-quenching medium boundary are calculated. For samples solidified in water, molten lead, and ceramic molds, the heat transfer coefficients are 0.41, 0.52, and 0.15 w/sq cm, respectively.

Abbaschian, G. J.↗
NASA NTRS1993

The microstructural evolution, crystallography, and thermal processing of ultrahigh carbon Fe-1.85 pct C melt-spun ribbon

A study is presented to determine if fine microstructures could be achieved using rapid solidification to produce a fine-grained fully austenitic starting structure and then using thermal processing cycles to produce an even finer ferrite-cementite structure. The evolution, mechanisms of grain refinement, and crystallography of the resultant microstructures were examined by TEM. A thermal processing cycle consisted of quenching the ribbon in liquid nitrogen, tempering at 600 C for 10 sec, 'upquenching' to 750 C for 10 sec, and subsequently quenching again in liquid nitrogen. The heat-treatment resulted in martensite grains with sizes of about 1 micron or less in both length and thickness and cementite particles of 0.4 micron or less. It is concluded that these microstructures could be used for producing fine-grained ultrahigh carbon steels of very high strength without the brittleness associated with the formation of coarse carbide particles of the loss of strength due to graphite formation.

Spanos, G.↗
NASA NTRS2010

Advances in Solid State Joining of Haynes 230 High Temperature Alloy

The J-2X engine is being designed for NASA s new class of crew and launch vehicles, the Ares I and Ares V. The J-2X is a LOX/Hydrogen upper stage engine with 294,000 lbs of thrust and a minimum Isp of 448 seconds. As part of the design criteria to meet the performance requirements a large film-cooled nozzle extension is being designed to further expand the hot gases and increases the specific impulse. The nozzle extension is designed using Haynes 230, a nickel-chromium-tungsten-molybdenum superalloy. The alloy was selected for its high strength at elevated temperatures and resistance to hydrogen embrittlement. The nozzle extension is manufactured from Haynes 230 plate spun-forged to form the contour and chemically-milled pockets for weight reduction. Currently fusion welding is being evaluated for joining the panels which are then mechanically etched and thinned to required dimensions for the nozzle extension blank. This blank is then spun formed into the parabolic geometry required for the nozzle. After forming the nozzle extension, weight reduction pockets are chemically milled into the nozzle. Fusion welding of Haynes results in columnar grains which are prone to hot cracking during forming processes. This restricts the ability to use spin forging to produce the nozzle contour. Solid state joining processes are being pursued as an alternative process to produce a structure more amenable to spin forming. Solid state processes have been shown to produce a refined grain structure within the joint regions as illustrated in Figure 1. Solid state joining processes include friction stir welding (FSW) and a patented modification termed thermal stir welding (TSW). The configuration of TSWing utilizes an induction coil to preheat the material minimizing the burden on the weld tool extending its life. This provides the ability to precisely select and control the temperature. The work presented in this presentation investigates the feasibility of joining the Haynes 230 alloy using the solid state welding processes of FSW and TSW. Process descriptions and attributes of each weld process will be presented. Weld process set-up and welding techniques will be discussed leading to the challenges experienced in joining the superalloy. Mechanical property data will also be presented.

Ding, R. Jeffrey↗
DOE OSTI2026

Quantitative characterization of gradient microstructures: A study on friction stir spot processing of pure cobalt

Heterogeneous microstructures in polycrystalline metals can enhance the strength and ductility, outperforming homogeneous structures of similar composition. This study investigates deformed cobalt via friction stir spot processing with varying dwell times to uncover the effects of plastic deformation and heat generation on the formation of morphological, phase, and grain boundary character gradients. A new approach to quantify the morphological gradients in materials, which describes grain morphology in terms of density followed by parametric regression, enables direct quantification of processing depth and gradient sharpness. Results show that longer processing times increase the steepness of morphological gradients and reduce the deformation depth for friction stir spot processing with low plunge depths and high tool rotational speeds. The amount of retained FCC is increased in the shorter processing conditions, primarily due to refined grain size, increased defect content, and reduced heat generation. Crystallographic texture analysis of the HCP phase indicated a dominant B-fiber described by (0001) ∥ shear plane normal in the extreme processing conditions and the formation of a P-fiber, shear direction ∥ ⟨11$\bar2$0⟩ for intermediate dwell times. The texture of the FCC phase for low processing times was a C texture {100}⟨011⟩ where longer processing times were dominated by a [001] fiber texture with a main {110}⟨100⟩ orientation and emergence of a slight [111] fiber in the longest processing condition. The approaches outlined in this work give insight into quantifying gradients and improve the understanding of highly deformed cobalt.

36 MATERIALS SCIENCE↗
NASA NTRS2008

Verifying and Validating Proposed Models for FSW Process Optimization

This slide presentation reviews Friction Stir Welding (FSW) and the attempts to model the process in order to optimize and improve the process. The studies are ongoing to validate and refine the model of metal flow in the FSW process. There are slides showing the conventional FSW process, a couple of weld tool designs and how the design interacts with the metal flow path. The two basic components of the weld tool are shown, along with geometries of the shoulder design. Modeling of the FSW process is reviewed. Other topics include (1) Microstructure features, (2) Flow Streamlines, (3) Steady-state Nature, and (4) Grain Refinement Mechanisms

Schneider, Judith↗
DOE OSTI2024

Refining Microstructures in Additively Manufactured Al/Cu Gradients Through TiB 2 Inclusions

Here, the additive manufacture of compositionally graded Al/Cu parts by laser engineered net shaping (LENS) is demonstrated. The use of a blue light build laser enabled deposition on a Cu substrate. The thermal gradient and rapid solidification inherent to selective laser melting enabled mass transport of Cu up to 4 mm from a Cu substrate through a pure Al deposition, providing a means of producing gradients with finer step sizes than the printed layer thicknesses. Divorcing gradient continuity from layer or particle size makes LENS a potentially enabling technology for the manufacture of graded density impactors for ramp compression experiments. Printing graded structures with pure Al, however, was prevented by the growth of Al 2 Cu 3 dendrites and acicular grains amid a matrix of Al 2 Cu. A combination of adding TiB 2 grain refining powder and actively varying print layer composition suppressed the dendritic growth mode and produced an equiaxed microstructure in a compositionally graded part. Material phase was characterized for crystal structure and nanoindentation hardness to enable a discussion of phase evolution in the rapidly solidifying melt pool of a LENS print.

36 MATERIALS SCIENCE↗