Search NASA⌕ Search

SEARCH · Search NASA

Results for “HST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Hubble Space Telescope (HST) Solar Array Damper

This paper describes the design of a solar array damper that will be built into each of two new solar arrays to be installed on the Hubble Space Telescope (HST) during Servicing Mission 3. On this mission, currently scheduled for August, 2000, two "rigid" solar array wings will replace the "flexible" wings currently providing power for HST. Dynamic interaction of these wings with the telescope spacecraft can affect the Pointing Control System. The damper, which is integral to the mast of the solar array, suppresses the fundamental bending modes of the deployed wings at 1.2 Hz (in-plane) and 1.6 Hz (out-of-plane). With the flight version of the damper, modal damping of 2.3% of critical is expected over the temperature range of -4 C to 23 C with a peak damping level of 3.9%. The unique damper design is a combination of a titanium spring and viscoelastic-shear-lap dashpot. The damper was designed using a system finite element model of the solar array wing and measured viscoelastic material properties. Direct complex stiffness (DCS) testing was performed to characterize the frequency- and temperature-dependent behavior of the damping prior to fixed-base modal testing of the wing at NASA/Goddard Space Flight Center (NASA/GSFC).

Maly, J. R.↗

HST Multi Layer Insulation Failure Review Board Findings

The mechanical and optical properties of the thermal control materials on the Hubble Space Telescope (HST) have degraded over the nearly seven years the telescope has been in orbit. Astronaut observations and photographs from the Second Servicing Mission (SM2) revealed large cracks in the metallized Teflon fluorinated ethylene propylene (FEP), the outer layer of the multi-layer insulation (MLI), in many locations around the telescope. Also, the absorptance of the bonded metallized Teflon FEP radiator surfaces of the telescope has increased over time. A Failure Review Board was established to determine the damage mechanism and to identify a replacement material. Samples of the top layer of the MLI and radiator material were retrieved during SM2, and a thorough investigation into the degradation followed in order to determine the primary cause of the damage. Mapping of the cracks on HST and the ground testing showed that thermal cycling with deep-layer damage from electron and proton radiation are necessary to cause the observed embrittlement. Further, strong evidence was found indicating that chain scission (reduced molecular weight) is the dominant form of damage to the metallized Teflon FEP. Given the damage to the outer layer of the multi-layer insulation (MLI) that was apparent during the second servicing mission (SM2), the decision was made to replace the outer layer during subsequent servicing missions. The replacement material had to meet the stringent thermal requirements of the spacecraft and maintain structural integrity for at least ten years. Ten candidate materials were exposed to simulated orbital environments and a replacement material was selected. This presentation will summarize the FRB results, in particular, the analysis of the retrieved specimens, the results of the simulated environmental exposures, and the selection of the replacement material. The NASA Space Environments and Effects community needs to hear these results because they reveal that Teflon (FEP) films should not be used in LEO as routinely as they are today.

Townsend, Jacqueline↗

Optical Metrology for the Filter Set for the Hubble Space Telescope (HST) Advanced Camera for Surveys (ACS)

The Hubble Space Telescope (HST) Advanced Camera for Surveys (ACS) will employ a wide variety of spectral filtration components including narrow band, medium band, wide band, and far ultraviolet (FUV) long pass filters, spatially- variable filters (ramp filters), VIS/IR polarizers, NUV polarizers, FUV prisms, and a grism. These components are spread across ACS's Wide Field, High Resolution, and Solar Blind channels which provide diffraction-limited imaging of astronomical targets using aberration-correcting optics which remove most aberrations from HST's Optical Telescope Assembly (OTA). In order for ACS to be truly advanced, these filters must push the state-of-the-art in performance in a number of key areas at the same time. Important requirements which these filters must meet include outstanding transmitted wavefront, high transmittance, uniform transmittance across each filter, spectrally structure-free bandpasses, exceptionally high out of band rejection, and a high degree of parfocality. These constitute a very stringent set of requirements indeed, especially for filters which are up to 90 mm in diameter. The development of optical metrology stations used to demonstrate that each ACS filter will meet its design specifications is discussed. Of particular note are specially-designed spectral transmissometers and interferometers.

Leviton, Douglas B.↗

Broadband Interferometer for Measuring Transmitted Wavefronts of Optical Bandpass Filters for HST (ACS)

The transmitted wavefronts of optical filters for the Hubble Space Telescope (HST) Advanced Camera for Surveys (ACS) are characterized using the Wildly and Openly Modified Broadband Achromatic Twyman Green (WOMBAT) Interferometer developed in the NASA/GSFC Optics Branch's Diffraction Grating Evaluation Facility (DGEF). Because only four of thirty-three of ACS's optical bandpass filters transmit the 633 nm light of most commercial interferometers, a broadband interferometer is required to verify specified transmitted wavefront of ACS filters. WOMBAT's design is a hybrid of the BAT interferometer developed by JPL used for HST Wide Field and Planetary Camera 2 (WFPC-2) filters and a WYKO 400 phase shifting interferometer. It includes a broadband light source, monochromator, off-axis, parabolic collimating and camera mirrors, an aluminum-coated fused silica beam splitter, flat retroreflecting mirrors for the test and reference arms, and a LTV-sensitive CCD camera. An outboarded, piezo-electric phase shifter holds the flat mirror in the interferometer's reference arm. The interferometer is calibrated through interaction between the WYKO system's software and WONMAT hardware for the test wavelength of light entering the beam splitter. Phase-shifted interferograms of the filter mounted in the test arm are analyzed using WYKO's Vision' software. Filters as large as 90 mm in diameter have been measured over a wavelength range from 200 to 1100 nm with a sensitivity of lambda/200 rms at lambda = 633 nm. Results of transmitted wavefront measurements are shown for ACS fixed band pass and spatially-variable bandpass filters for a variety of wavelengths.

Boucarut, R. A.↗

Analysis of Mars HST Observations

During the 1997 Mars opposition, several observations of Mars were obtained with the Wide Field/Planetary Camera 2 (WFPC2) of the Hubble Space Telescope (HST). We have analyzed two sets of those observations obtained on March 30 and March 31 of 1997 as part of HST GO Programs 6741 and 6793. Our analysis has included a search for evidence of the coarse-grained hematite deposit reported by the Mars Global Surveyor Thermal Emission Spectrometer (TES) as well as other materials. Although no compelling evidence has verified the TES discovery, spectral signatures have been identified at other locations on the Martian disk that may be consistent with coarse-grained hematite. Additional information is contained in the original extended abstract.

Smith, P. H.↗

STOP Analysis and Optimization of a Very-Low-Distortion Space Instrument: HST WFC3 Case Study

New generation optical instruments with very demanding stability requirements are being proposed and developed for space applications. STOP (Structural-Thermal-Optical Performance) analysis and optimization is crucial in meeting the very tight distortion budgets of these instruments. This presentation outlines STOP analysis and optimization approach in the context of WFC3 (Wide-Field Camera 3), which is a radial instrument designed to replace the Wide-Field Planetary Camera 2 (WFPC2) of the Hubble Space Telescope (HST). WFC3 houses two separate channels, UVIS and IR, and will have greater throughput and sensitivity than WFPC2. WFC3 line-of-sight alignment budget for the UVIS and IR channels are as small as 10 and 20 milli-arcsec, respectively. Its optical bench is the most critical subsystem effecting the optical stability of WFC3 hence our effort concentrates on the design and analysis of the bench and its interfaces. Structural analysis has accompanied the mechanical design of the bench since the initial concept study. A high fidelity structural Finite Element Model (FEM) of the bench has been developed and used for minimizing its thermally induced distortions as well as sizing it to meet the stiffness and strength requirements of a Shuttle launch. The bench is a composite honeycomb panel box structure with a very low planar Coefficient of Thermal Expansion (CTE) of approximately 0.1 ppm/C. Optic components are mounted to super-INVAR inserts bonded into the panels. The bench is kinematically supported on three HST latches via interface struts, which are tailored to exhibit negative CTE to cancel out the thermal motions of the latches. The interface struts also incorporate flexure elements to minimize the mechanical distortions coming into the bench from its enclosure. Bench FEM is coupled with the enclosure FEM to quantify these effects. Short term or on-orbit STOP analysis includes distortion due to the temperature variations of the bench, the struts, and the enclosure. Long term or ground-to-orbit STOP analysis includes distortional effects of gravity release, desorption, and assembly in addition to the ground-to-orbit temperature variations. A rigorous testing program has been implemented for verifying the material properties and the analysis predictions. STOP analysis results demonstrate that both the short-term and the long-term alignment budgets will be met. Presentation will cover design and analysis details that are critical to a successful implementation of the STOP analysis and optimization process.

Kunt, Cengiz↗

Correlation of the Hubble Space Telescope (HST) Space Telescope Imaging Spectrometer (STIS) On-Orbit Data with Pre-launch Predictions and Ground Contamination Controls

The Hubble Space Telescope (HST) Space Telescope Imaging Spectrograph (STIS) was deployed on-orbit in February 1997. The contamination program for STIS was stringently controlled as the five-year end-of-life deposition was set at 158, per optical element. Contamination was controlled through materials selection, extensive vacuum outgassing certifications, cleaning techniques, and environmental controls. In addition to ground contamination controls, on-orbit contamination controls were implemented for both the HST servicing mission activities and early post-servicing mission checkout. The extensive contamination control program will be discussed and the STIS on-orbit data will be correlated with the prelaunch analytical predictions.

Hansen, Patricia A.↗

Planetary Nebulae in the MW, LMC, SMC: Results from FUSE and HST data

We use FUSE and HST data to study Planetary Nebulae (PN) systems in the Milky Way, LMC and SMC. Theoretically, metallicity affects several aspects of the post-AGB evolution, including mass-loss and the yield of processed material, which are important factors in the chemical evolution of galaxies. Therefore, it is very important to study PNe in different environments. In Bianchi's FUSE programs, we observed CSPN in the Milky Way (Cycle 1), LMC (Cycle 2) and SMC (Cyde 3), representing a range of metallicities from solar to 1/10th solar. The far-UV range reveals the spectrum of the central star (CSPN), uniquely enabling a direct estimate of the ionizing source parameters. Combined with archive HST data, these spectra provide a measurement of T(sub eff), log g, L(sub bol), abundances, wind velocity and mass-loss rate for these post-AGB stars. Additionally, these spectra provide a measurement of the circumstellar H2 and HI, which added to the mass of the central star and of the ionized shell allows us to test theoretical initial-final mass relations, and to put together a complete picture of the star's evolution.

Herald, J. E.↗

Simultaneous FUSE, HST, and Chandra Observations or Intrinsic Absorbers in NGC 7469 and MRK 279

We obtained FUSE observations of NGC 7469 on 2002 Dec 13 & 14. The two exposures totaled only 7 ks. The observations only have good data in one channel, LiF1, due to channel alignment problems. These observations were obtained simultaneously with high-quality HST/STIS and Chandra HETG spectra. The previously known O VI absorption lines in the FUSE spectrum are detected at good signal to noise ratio, and a wide array of other intrinsic absorption lines are visible in the X-ray spectrum and in the STIS spectrum. Compared to prior FUSE observations, the continuum flux for this observation was 50% lower. We see the effects of this in the lowest-velocity O VI absorber, which we associate with the X-ray absorbing gas also detected in this object. This O VI absorber has only a 50% covering fraction, consistent with its covering only the continuum in this source, and its strength and inferred column density increased as the continuum flux of NGC 7469 decreased. This is consistent with the recombination expected from photoionization models of the highly ionized gas. We obtained FUSE observations of Mrk 279 on 2002 May 18. As for NGC 7469, channel alignment problems led to good data being present only in LiFl. While we obtained a much longer integration on the target than planned (47.4 ks vs. 31 ks requested), the UV flux was down a factor of 10 or more from previous HST and FUSE observations, and our wavelength coverage was restricted due to the channel alignment problems. These data still cover the important O VI emission line and absorption lines in Mrk 279. The FUSE flux also agrees well with the simultaneous HST STIS data, which have good signal to noise. We have also analyzed FUSE observations made at three earlier epochs. We detect the Fe K-alpha emission line in the Chandra spectrum, and its flux is consistent with the low X-ray continuum flux level of Mrk 279 at the time of the observation. Because of low signal-to-noise ratios (S/N) in the Chandra spectrum, no O VII or O VIII absorption features are observable in the Chandra data, but the UV spectra reveal strong and complex absorption from H I and high-ionization species such as O VI, N V, and C IV, as well as from low-ionization species such as C III, N III, C II, and N II in some velocity components. The far-UV spectral coverage of the FUSE data provides information on high-order Lyman series absorption, which we use to calculate the optical depths and line and continuum covering fractions in the intrinsic H I absorbing gas in a self-consistent fashion. Based on the velocities, profile shapes, covering fractions and variability of the UV absorption, we conclude that some of the absorption components, particularly those showing prominent low-ionization lines, are likely associated with the host galaxy of Mrk 279, and possibly with its interaction with a close companion galaxy, while the remainder arises in a nuclear outflow.

Sonneborn, George↗

Systems Engineering and Integration for Advanced Life Support System and HST

Systems engineering (SE) discipline has revolutionized the way engineers and managers think about solving issues related to design of complex systems: With continued development of state-of-the-art technologies, systems are becoming more complex and therefore, a systematic approach is essential to control and manage their integrated design and development. This complexity is driven from integration issues. In this case, subsystems must interact with one another in order to achieve integration objectives, and also achieve the overall system's required performance. Systems engineering process addresses these issues at multiple levels. It is a technology and management process dedicated to controlling all aspects of system life cycle to assure integration at all levels. The Advanced Integration Matrix (AIM) project serves as the systems engineering and integration function for the Human Support Technology (HST) program. AIM provides means for integrated test facilities and personnel for performance trade studies, analyses, integrated models, test results, and validated requirements of the integration of HST. The goal of AIM is to address systems-level integration issues for exploration missions. It will use an incremental systems integration approach to yield technologies, baselines for further development, and possible breakthrough concepts in the areas of technological and organizational interfaces, total information flow, system wide controls, technical synergism, mission operations protocols and procedures, and human-machine interfaces.

Kamarani, Ali K.↗

Saturn's Hydrogen Aurora as Observed by HST

We describe Saturn's aurora as observed by HST in 10/1994, 10/1995, and 10-12/1997. HST provides access to the auroral emissions due to atomic and molecular hydrogen in the northern and southern auroral zones.

magnetospheres planets auroral↗

The HST Key Project on the Extragalactic Distance Scale XI. The Cepheids in NGC 4414

We report the Discovery of Cepheid variable stars in the galaxy NGC 4414, as part of the Hubble Space Telescope (HST) Key Project on the Extragalactic Distance Scale. Observations were obtained with the HST Wide Field and Planetary Camera 2 (WFPC2) for 13 epochs at V (F555W) and 4 at I (F814W).

Cepheids distance and redshifts galaxies NGC 4414↗

Processing Raw HST Data With Up-to-Date Calibration Data

On-the-Fly Reprocessing (OTFR) is a collection of data-processing routines that work within the context of the Hubble Space Telescope (HST) pipeline data-flow system. The purpose served by OTFR is to generate, on demand, scientifically useful data products from raw HST data stored in an archive. First, on the basis of the requested final data products, OTFR retrieves the corresponding sets of raw data from the archives. Next, OTFR processes the raw data sets to remove artifacts and to establish proper header and other template information. Finally, the calibration routines appropriate to the specific data sets are invoked to produce the requested data products, and the data products are released to an archive distribution system for transmission to the requesting party. OTFR offers two notable advantages: (1) Inasmuch as calibrated data occupy about 8 times as much storage space as do raw data, by obviating storage of calibrated data, OTFR reduces the storage capacity needed by the archive; and (2) the calibration routines can be updated to give requesters the benefit of the most recent calibrations.

Miller, Warren↗

Flight Results from the HST SM4 Relative Navigation Sensor System

On May 11, 2009, Space Shuttle Atlantis roared off of Launch Pad 39A enroute to the Hubble Space Telescope (HST) to undertake its final servicing of HST, Servicing Mission 4. Onboard Atlantis was a small payload called the Relative Navigation Sensor experiment, which included three cameras of varying focal ranges, avionics to record images and estimate, in real time, the relative position and attitude (aka "pose") of the telescope during rendezvous and deploy. The avionics package, known as SpaceCube and developed at the Goddard Space Flight Center, performed image processing using field programmable gate arrays to accelerate this process, and in addition executed two different pose algorithms in parallel, the Goddard Natural Feature Image Recognition and the ULTOR Passive Pose and Position Engine (P3E) algorithms

Naasz, Bo↗

Thermal Design Considerations of the Hubble Space Telescope (HST) Science Instrument Control and Data Handler (SI C and DH-2)

Following a failure in side 1 of the HST SI C&DH in September 2008, HST Servicing Mission 4 (SM-4) was delayed so that a SI C&DH Orbital Replacement Unit (ORU) could be qualified for flight. This second generation SI C&DH (SI C&DH-2) included several enhancements which increased its thermal dissipation near critical components. In order to maintain the SI C&DH-2 within its operational temperature limits, several thermal modifications were installed prior to its final qualification testing. This paper presents the thermal modifications performed on the SI C&DH-2, as well as the thermal ground test results and a correlation of the SI C&DH-2 thermal design to flight telemetry.

Gregory, Teri H.↗

The Radial Distribution of Star Formation in Galaxies at Z approximately 1 from the 3D-HST Survey

The assembly of galaxies can be described by the distribution of their star formation as a function of cosmic time. Thanks to the WFC3 grism on the Hubble Space Telescope (HST) it is now possible to measure this beyond the local Universe. Here we present the spatial distribution of H emission for a sample of 54 strongly star-forming galaxies at z 1 in the 3D-HST Treasury survey. By stacking the H emission, we find that star formation occurred in approximately exponential distributions at z approximately 1, with a median Sersic index of n = 1.0 +/- 0.2. The stacks are elongated with median axis ratios of b/a = 0.58 +/- 0.09 in H consistent with (possibly thick) disks at random orientation angles. Keck spectra obtained for a subset of eight of the galaxies show clear evidence for rotation, with inclination corrected velocities of 90.330 km s(exp 1-). The most straightforward interpretation of our results is that star formation in strongly star-forming galaxies at z approximately 1 generally occurred in disks. The disks appear to be scaled-up versions of nearby spiral galaxies: they have EW(H alpha) at approximately 100 A out to the solar orbit and they have star formation surface densities above the threshold for driving galactic scale winds.

Nelson, Erica June↗

A Lyman Break Galaxy in the Epoch of Reionization from Hubble Space Telescope (HST) Grism Spectroscopy

Slitless grism spectroscopy from space offers dramatic advantages for studying high redshift galaxies: high spatial resolution to match the compact sizes of the targets, a dark and uniform sky background, and simultaneous observation over fields ranging from five square arcminutes (HST) to over 1000 square arcminutes (Euclid). Here we present observations of a galaxy at z = 6.57 the end of the reioinization epoch identified using slitless HST grism spectra from the PEARS survey (Probing Evolution And Reionization Spectroscopically) and reconfirmed with Keck + DEIMOS. This high redshift identification is enabled by the depth of the PEARS survey. Substantially higher redshifts are precluded for PEARS data by the declining sensitivity of the ACS grism at greater than lambda 0.95 micrometers. Spectra of Lyman breaks at yet higher redshifts will be possible using comparably deep observations with IR-sensitive grisms.

Rhoads, James E.↗

The Radial Distribution of Star Formation in Galaxies at z~1 From The 3D-HST Survey

The assembly of galaxies can be described by the distribution of their star formation as a function of cosmic time.Thanks to the WFC3 grism on the Hubble Space Telescope (HST) it is now possible to measure this beyond thelocal Universe. Here we present the spatial distribution of H emission for a sample of 54 strongly star-forming-galaxies at z~1 in the 3D-HST Treasury survey. By stacking the Halpha emission, we find that star formation occurredin approximately exponential distributions at z~1, with a median Sersic index of n=1.0 plus or minus 0.2. The stacks areelongated with median axis ratios of b/a 0.58 plus or minus 0.09 in Halpha consistent with (possibly thick) disks at randomorientation angles. Keck spectra obtained for a subset of eight of the galaxies show clear evidence for rotation, withinclination corrected velocities of 90-330 km per second. The most straightforward interpretation of our results is that starformation in strongly star-forming galaxies at z~1 generally occurred in disks. The disks appear to be scaled-upversions of nearby spiral galaxies: they have EW(Halpha)~100 Angstroms out to the solar orbit and they have star formation surface densities above the threshold for driving galactic scale winds.

Radial↗