Search NASA⌕ Search

SEARCH · Search NASA

Results for “HULLS - IMPACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1935

The Effect of Spray Strips on the Take-off Performance of a Model of a Flying-Boat Hull

The effect on the take-off performance of a model of the hull of a typical flying boat, Navy PH-1, of fitting spray strips of four different widths, each at three different angles, was determined by model tests in the NACA Tank. Spray strips of widths up to 3 percent of the beam improve the general performance at speeds near the hump and reduce the spray thrown. A downward angle of 30 degrees to 45 degrees in the neighborhood of the step seems most favorable for the reduction of the spray. The spray strips have a large effect in reducing the trimming moments at speeds near the hump speed, but have little effect on them at high speeds.

Truscott, Starr↗
NASA NTRS1938

A discussion of certain problems connected with the design of hulls of flying boats and the use of general test data

Report presents the results of a survey of problems encountered in applying general test data to the design of flying-boat hulls. It is shown how basic design features may be readily determined from special plots of test data. A study of the effect of the size of a flying boat on the probable limits to be covered by the general test data is included and recommendations for special tests and new methods of presenting test data for direct use in design are given.

Diehl, Walter S↗
NASA NTRS1940

The application of basic data on planing surfaces to the design of flying-boat hulls

Basic lift data on planing surfaces have been analyzed and the data applied to the design of flying-boat hulls. It is shown that a balance between air and water forces requires that the beam of the planing area bear a relation to the wing area that is determined by the lift coefficient of the wing and by the angle of dead rise in the planing surface. It is also shown that the fore-and-aft extent of the required planing area depends on the angle of dead rise. Failure to provide sufficient length of planing area appears to be the main reason for the poor water performance sometimes obtained when a large angle of dead rise is used.

Diehl, Walter S↗
NASA NTRS1960

Transonic Aerodynamic Characteristics of a Model of a Proposed Six-Engine Hull-Type Seaplane Designed for Supersonic Flight

Force tests of a model of a proposed six-engine hull-type seaplane were performed in the Langley 8-foot transonic pressure tunnel. The results of these tests have indicated that the model had a subsonic zero-lift drag coefficient of 0.0240 with the highest zero-lift drag coefficient slightly greater than twice the subsonic drag level. Pitchup tendencies were noted for subsonic Mach numbers at relatively high lift coefficients. Wing leading-edge droop increased the maximum lift-drag ratio approximately 8 percent at a Mach number of 0.80 but this effect was negligible at a Mach number of 0.90 and above. The configuration exhibited stable lateral characteristics over the test Mach number range.

Wornom, Dewey E.↗
NASA NTRS1948

Hydrodynamic Characteristics of an Aerodynamically Refined Planing-Tail Hull

The hydrodynamic characteristics of an aerodynamically refined planing-tail hull were determined from dynamic model tests in Langley tank no. 2. Stable take-off could be made for a wide range of locations of the center of gravity. The lower porpoising limit peak was high, but no upper limit was encountered. Resistance was high, being about the same as that of float seaplanes. A reasonable range of trims for stable landings was available only in the aft range of center-of-gravity locations.

McKann, Robert↗
NASA NTRS1949

Full-Scale Hydrodynamic Evaluation of a Modified Navy J4F-2 Amphibian with a 0.425-Scale XP5M-1 Hull Bottom. TED No. NACA DE325

An investigation was made to evaluate the hydrodynamic qualities of a 0.425-scale model of the Navy XP5M-1 hull, which was installed on a modified Navy J4F-2 amphibian. Longitudinal and directional stability during take-off and landing, low-speed maneuverability, spray characteristics, and take-off performance were investigated. The behavior of the airplane in moderately rough water was also observed. The opinions of three pilots have been correlated with the data.

Land, Norman S.↗
NASA NTRS2021

Light-Robust Pole-from-Silhouette Algorithm and Visual-Hull Estimation for Autonomous Optical Navigation to an Unknown Small Body

We present an advanced Pole-from-Silhouette (PFS) algorithm, which is robust to illumination conditions and non-zero sun phase. PFS is an important step in the optical navigation pipeline for an autonomous small spacecraft to approach an unknown small body. The algo- rithm estimates the rotation pole and 3D shape (visual hull) of the small body using only the lit pixels within the silhouette of the small body, the body’s rotation rate, the spacecraft attitude, and the spacecraft-target relative distance, which is estimated from orbit determination. We present detailed numerical simulations and multiple sensitivity analyses to demonstrate the effectiveness of our proposed PFS algorithm in different scenarios and target bodies.

Nesnas, Issa A.↗