Results for “HYDROGEN FLUORIDE” — Page 5

NASA NTRS1961

The Electrochemical Fluorination of Organosilicon Compounds

The electrochemical fluorination of tetramethylsilane, hexamethyl-disiloxane, diethyldichlorosilane, amyltrichlorosilane, and phenyltri-chlorosilane was conducted in an Inconel cell equipped with nickel electrodes. A potential of approximately 5.0 volts and a current of approximately 1.0 ampere were used for the electrolysis reaction. In all cases the fluorinations resulted in considerable scission of the carbon-silicon bonds yielding hydrogen and the various fluorinated decomposition products; no fluoroorganosilicon compounds were identified. The main decomposition products were silicon tetrafluoride, the corresponding fluorinated carbon compounds, and the various organofluorosilanes. It is suggested that this is due to the nucleophilic attack of the fluoride ion (or complex fluoride ion) on the carbon-silicon bond.

Seaver, Robert E.↗

NASA NTRS1991

The PM-200 lubrication system

Plasma sprayed composite coating of metal-bonded chromium carbide with additions of silver and thermochemically stable fluorides were previously reported to be lubricative in pin on desk bench tests from room temperature to 900 C. An early coating formulation of this type, designated as PS-200, was successfully tested as a cylinder coating in a Stirling engine at a TRRT of 760 C in a hydrogen atmosphere, and as a backup lubricant for gas bearings to 650 C. A subsequent optimization program has shown that tribological properties are further improved by increasing the solid lubricant content. The improved coating is designated as PS-212. The same powder formulation was used to make free-standing powder metallurgy (PM-212) parts by sintering or hot isostatic pressing. The process is very attractive for making parts that cannot be readily plasma sprayed such as bushings and cylinders that have small bore diameters and/or high length to diameter ratios. The properties of coatings and free-standing parts fabricated from these powders are reviewed.

Sliney, Harold E.↗

NASA NTRSDate not supplied

A New Linear Polarizer Design for Application in the Far-Ultraviolet Spectral Range

New mission concepts that are under consideration by NASA (such as the Polstar MIDEX mission concept) call for the design and implementation of Far Ultraviolet (FUV) polarizer technologies that have not been developed yet. A team that includes members from the NASA Goddard Space Flight Center (GSFC), Arizona State University (ASU), and Woodruff Consulting, worked on the design and development of a polarizer design that may produce extinction ratios higher than have ever been reported before in the FUV spectral range (100-200 nm). This polarizer consists of transmitting linearly polarized light through a series of reflections from a combination of two silicon carbide (SiC) and two lithium fluoride (LiF) crystals positioned at angles of incidence (relative to surface normal) close to the LiF Brewster’s angle. The performance of this polarizer concept was fabricated and tested with an existing McPherson 225 Vacuum Ultraviolet (VUV) spectrometer located in the Optics Branch at NASA-GSFC. Initial testing has shown that in the FUV spectral range, this design can produce state-of-the-art extinction ratios at the Hydrogen Lyman-Alpha (Ly-α) wavelength of 121.6 nm. A polarizer with such a performance has never been reported and it signifies a breakthrough in FUV polarization technology. The levels of effectiveness paired with the design’s compact design allows for a new polarizer capability that would one day be implemented in a future spectropolarimetry space mission. In addition, this polarizer concept could potentially be used to characterize the optical properties of new mirror coatings that will be used in a future Habitable World Observatory (HWO) mission concept as proposed by the 2020 Decadal Survey.2

Far Ultraviolet (FUV), polarimetry, instrumentatio↗

NASA NTRSDate not supplied

Linear Polarizer Design for Application in the Far-Ultraviolet Spectral Range

New mission concepts that are under consideration by NASA (such as the Polstar MIDEX mission concept) call for the design and implementation of Far Ultraviolet (FUV) polarizer technologies that have not been developed yet. A team that includes members from the NASA Goddard Space Flight Center (GSFC), Arizona State University (ASU), and Woodruff Consulting, worked on the design and development of a polarizer design that may produce extinction ratios higher than have ever been reported before in the FUV spectral range (100-200 nm). This polarizer consists of transmitting linearly polarized light through a series of reflections from a combination of two silicon carbide (SiC) and two lithium fluoride (LiF) crystals positioned at angles of incidence (relative to surface normal) close to the LiF Brewster’s angle. The performance of this polarizer concept was fabricated and tested with an existing McPherson 225 Vacuum Ultraviolet (VUV) spectrometer located in the Optics Branch at NASA-GSFC. Initial testing has shown that in the FUV spectral range, this design can produce state-of-the-art extinction ratios at the Hydrogen Lyman-Alpha (Ly-α) wavelength of 121.6 nm. A polarizer with such a performance has never been reported and it signifies a breakthrough in FUV polarization technology. The levels of effectiveness paired with the design’s compact design allows for a new polarizer capability that would one day be implemented in a future spectropolarimetry space mission. In addition, this polarizer concept could potentially be used to characterize the optical properties of new mirror coatings that will be used in a future Habitable World Observatory (HWO) mission concept as proposed by the 2020 Decadal Survey.2

Far Ultraviolet (FUV), polarimetry, instrumentatio↗

NASA NTRS2007

Space and Terrestrial Power System Integration Optimization Code BRMAPS for Gas Turbine Space Power Plants With Nuclear Reactor Heat Sources

In view of the difficult times the US and global economies are experiencing today, funds for the development of advanced fission reactors nuclear power systems for space propulsion and planetary surface applications are currently not available. However, according to the Energy Policy Act of 2005 the U.S. needs to invest in developing fission reactor technology for ground based terrestrial power plants. Such plants would make a significant contribution toward drastic reduction of worldwide greenhouse gas emissions and associated global warming. To accomplish this goal the Next Generation Nuclear Plant Project (NGNP) has been established by DOE under the Generation IV Nuclear Systems Initiative. Idaho National Laboratory (INL) was designated as the lead in the development of VHTR (Very High Temperature Reactor) and HTGR (High Temperature Gas Reactor) technology to be integrated with MMW (multi-megawatt) helium gas turbine driven electric power AC generators. However, the advantages of transmitting power in high voltage DC form over large distances are also explored in the seminar lecture series. As an attractive alternate heat source the Liquid Fluoride Reactor (LFR), pioneered at ORNL (Oak Ridge National Laboratory) in the mid 1960's, would offer much higher energy yields than current nuclear plants by using an inherently safe energy conversion scheme based on the Thorium --> U233 fuel cycle and a fission process with a negative temperature coefficient of reactivity. The power plants are to be sized to meet electric power demand during peak periods and also for providing thermal energy for hydrogen (H2) production during "off peak" periods. This approach will both supply electric power by using environmentally clean nuclear heat which does not generate green house gases, and also provide a clean fuel H2 for the future, when, due to increased global demand and the decline in discovering new deposits, our supply of liquid fossil fuels will have been used up. This is expected within the next 30 to 50 years, as predicted by the Hubbert model and confirmed by other global energy consumption prognoses. Having invested national resources into the development of NGNP, the technology and experience accumulated during the project needs to be documented clearly and in sufficient detail for young engineers coming on-board at both DOE and NASA to acquire it. Hands on training on reactor operation, test rigs of turbomachinery, and heat exchanger components, as well as computational tools will be needed. Senior scientist/engineers involved with the development of NGNP should also be encouraged to participate as lecturers, instructors, or adjunct professors at local universities having engineering (mechanical, electrical, nuclear/chemical, and/or materials) as one of their fields of study.

Juhasz, Albert J.↗

NASA NTRS1986

Composition optimization of self-lubricating chromium carbide-based composite coatings for use to 760 deg C

This paper describes new compositions of self-lubricating coatings that contain chromium carbide. A bonded chromium carbide was used as the base stock because of the known excellent wear resistance and the chemical stability of chromium carbide. Additives were silver and barium fluoride/calcium fluoride eutectic. The coating constituents were treated as a ternary system consisting of: (1) the bonded carbide base material, (2) silver, and (3) the eutectic. A study to determine the optimum amounts of each constituent was performed. The various compositions were prepared by powder blending. The blended powders were then plasma sprayed onto superalloy substrates and diamond ground to the desired coating thickness. Friction and wear studies were performed at temperatures from 25 to 760 C in helium and hydrogen. A variety of counterface materials were evaluated with the objective of discovering a satisfactory metal/coating sliding combination for potential applications such as piston ring/cylinder liner couples for Stirling engines.

Dellacorte, C.↗

NASA NTRS1987

Composition optimization of self-lubricating chromium-carbide-based composite coatings for use to 760 C

This paper describes new compositions of self-lubricating coatings that contain chromium carbide. A bonded chromium carbide was used as the base stock because of the known excellent wear resistance and the chemical stability of chromium carbide. Additives were silver and barium fluoride/calcium fluoride eutectic. The coating constituents were treated as a ternary system consisting of: (1) the bonded carbide base material, (2) silver, and (3) the eutectic. A study to determine the optimum amounts of each constituent was performed. The various compositions were prepared by powder blending. The blended powders were then plasma sprayed onto superalloy substrates and diamond ground to the desired coating thickness. Friction and wear studies were performed at temperatures from 25 to 760 C in helium and hydrogen. A variety of counterface materials were evaluated with the objective of discovering a satisfactory metal/coating sliding combination for potential applications such as piston ring/cylinder liner couples for Stirling engines.

Dellacorte, Chris↗

NASA NTRS2024

Optimization of Mission Enabling Broadband Lyman Ultraviolet Series to Infrared Aluminum Lithium Fluoride Reflectors

The Habitable Worlds Observatory (HWO) concept NASA flagship mission aims extend the ultraviolet (UV) observation range and sensitivity capabilities of the Hubble Space Telescope (HST) with respective goals of reaching photons down to 100 nm and containing an ultraviolet multi-object spectrograph with sensitivity improved 30-100 times. Adding the sensitivity capabilities near the Lyman series spectral range of ~100-121.6 nm reduces the reliance of redshift for key diagnostic ion lines such as O VI (103.2 nm), and heavily ionized gases of Ne VIII (77.5 nm) and MgX (62.5 nm). Clean and unoxidized aluminum (Al) reflectors provide optimal efficiency over a broadband down to the extreme ultraviolet (EUV) wavelength of ~83 nm. To prevent oxidation and maintain high spectral efficiency down to ~100 nm, the Al reflector is conventionally overcoated with a thin lithium fluoride (LiF) layer. We investigate the optimization of the deposition of the Al+LiF coating material composition to attain high spectral efficiency broadband reflectors down to 100 nm and enable the scientific goals of HWO. Lithium hexafluoroaluminate (Li3AlF6) is investigated as a different composition form of LiF to overcoat Al. The spectral efficiency and durability of the reflectors is evaluated. We will demonstrate the use of Li3AlF6 as an overcoat to protect aluminum yields ultra-high efficiency at the Hydrogen Lyman-alpha (HLyα, 121.6 nm) line with experimental reflectance values peaking up to 99%.

optical coatings↗

NASA NTRS2024

Optimization of Mission Enabling Broadband Lyman Ultraviolet Series to Infrared Aluminum Lithium Fluoride Reflectors

The Habitable Worlds Observatory (HWO) concept NASA flagship mission aims extend the ultraviolet (UV) observation range and sensitivity capabilities of the Hubble Space Telescope (HST) with respective goals of reaching photons down to 100 nm and containing an ultraviolet multi-object spectrograph with sensitivity improved 30-100 times. Adding the sensitivity capabilities near the Lyman series spectral range of ~100-121.6 nm reduces the reliance of redshift for key diagnostic ion lines such as O VI (103.2 nm), and heavily ionized gases of Ne VIII (77.5 nm) and MgX (62.5 nm). Clean and unoxidized aluminum (Al) reflectors provide optimal efficiency over a broadband down to the extreme ultraviolet (EUV) wavelength of ~83 nm. To prevent oxidation and maintain high spectral efficiency down to ~100 nm, the Al reflector is conventionally overcoated with a thin lithium fluoride (LiF) layer. We investigate the optimization of the deposition of the Al+LiF coating material composition to attain high spectral efficiency broadband reflectors down to 100 nm and enable the scientific goals of HWO. Lithium hexafluoroaluminate (Li3AlF6) is investigated as a different composition form of LiF to overcoat Al. The spectral efficiency and durability of the reflectors is evaluated. We will demonstrate the use of Li3AlF6 as an overcoat to protect aluminum yields ultra-high efficiency at the Hydrogen Lyman-alpha (HLyα, 121.6 nm) line with experimental reflectance values peaking up to 99%.

optical coatings↗

NASA NTRSDate not supplied

Linear Polarizer Design for Application in the Far-Ultraviolet Spectral Range

New mission concepts that are under consideration by NASA call for the design and implementation of Far Ultraviolet (FUV) polarizer technologies that have not been developed yet. A team that includes members from the NASA Goddard Space Flight Center (GSFC), Arizona State University (ASU), and Woodruff Consulting, worked on the design and development of a polarizer design that produce very high extinction ratios in the FUV spectral range (100-200 nm). This polarizer consists of reflecting light through a series of mirrors from a combination of two silicon carbide (SiC) and two lithium fluoride (LiF) crystals positioned at angles of incidence (relative to surface normal) close to the average LiF Brewster’s angle in the FUV. The output is a highly linearly polarized beam. This polarizer concept was fabricated and tested in the existing McPherson 225 Vacuum Ultraviolet (VUV) spectrometer located in the Optics Branch at NASA-GSFC. Initial testing using a MgF2 crystal at the Brewster’s angle as an analyzer has shown that this design can produce state-of-the-art extinction ratios at the Hydrogen Lyman-Alpha (Ly-α) wavelength of 121.6 nm, and that the measured extinction ratio of the two crossed polarizers, ≈114, is mostly limited by the MgF2 analyzer. A polarizer with such a performance at this wavelength has never been reported and it signifies a breakthrough in FUV polarization technology. The levels of effectiveness paired with the polarizer’s compact design allows for a new polarizer capability that would one day be implemented in a future FUV spectropolarimetry space mission.

Far Ultraviolet (FUV)↗

NASA NTRS2023

Cryolite Overcoated Aluminum Reflectors for Far-Ultraviolet Spectroscopy

Aluminum (Al) mirrors are conventionally protected with metal-fluoride coatings (e.g., MgF2, LiF, or AlF3) immediately after deposition to prevent oxidation and preserve its far-ultraviolet (FUV) spectral efficiency. However, the resulting FUV reflectance of the aluminum reflector is limited by the metal-fluoride overcoat film index of refraction, morphology, stoichiometry, and its absorption cut-off in the lower end of the FUV spectra. Cryolite (sodium hexafluoroaluminate, Na3AlF6) emerges as a potential candidate to preserve the aluminum FUV reflectance due to its relatively lower index of refraction in the visible to ultraviolet; therefore, allowing for the thin-film design of highly spectral efficient reflectors over a wide spectral range. We investigate the use of cryolite in aluminum reflector FUV coating design. The deposited aluminum reflector overcoated with cryolite will be examined in terms of spectral efficiency and environmental durability. The deposited cryolite overcoat will be evaluated in terms of optical constants and structural properties. Preliminary results have shown that the use of cryolite as an overcoat to protect aluminum would yield unprecedented results as an optimal Hydrogen Lyman-alpha (HLyα) spectral line reflector, with experimental reflectance values >96%.

optical coatings↗

NASA NTRSDate not supplied

Cryolite Overcoated Aluminum Reflectors for Far-Ultraviolet Spectroscopy

Aluminum (Al) mirrors are conventionally protected with metal-fluoride coatings (e.g., MgF 2 , LiF, or AlF 3 ) immediately after deposition to prevent oxidation and preserve its far-ultraviolet (FUV) spectral efficiency. However, the resulting FUV reflectance of the aluminum reflector is limited by the metal-fluoride overcoat film index of refraction, morphology, stoichiometry, and its absorption cut-off in the lower end of the FUV spectra. Cryolite (sodium hexafluoroaluminate, Na 3 AlF 6 ) emerges as a potential candidate to preserve the aluminum FUV reflectance due to its relatively lower index of refraction in the visible to ultraviolet; therefore, allowing for the thin-film design of highly spectral efficient reflectors over a wide spectral range. We investigate the use of cryolite in aluminum reflector FUV coating design. The deposited aluminum reflector overcoated with cryolite will be examined in terms of spectral efficiency and environmental durability. The deposited cryolite overcoat will be evaluated in terms of optical constants and structural properties. Preliminary results have shown that the use of cryolite as an overcoat to protect aluminum would yield unprecedented results as an optimal Hydrogen Lyman-alpha (HLyα) spectral line reflector, with experimental reflectance values >96%.

optical coating↗

NASA NTRS1991

Oxygen extraction from lunar soil by fluorination

Mining and processing of lunar material could possibly lead to more cost-efficient scenarios for permanent presence of man in space and on the Moon. Production of oxygen for use as propellant seems especially important. Different candidate processes for oxygen-extraction from lunar soil were proposed, of which the reduction of ilmenite by hydrogen was studied most. This process, however, needs the concentration of ilmenite from lunar regolith to a large extent and releases oxygen only with low efficiency. Another possibility - the fluorination method - which works with lunar bulk material as feedstock is discussed. Liberation of oxygen from silicate or oxide materials by fluorination methods has been applied in geoscience since the early sixties. The fact that even at moderate temperatures 98 to 100 percent yields can be attained, suggests that fluorination of lunar regolith could be an effective way of propellant production. Lunar soil contains about 50 percent oxygen by weight which is gained nearly completely through this process as O2 gas. The second-most element Si is liberated as gaseous SiF4. It could be used for production of Si-metal and fluorine-recycling. All other main elements of lunar soil will be converted into solid fluorides which also can be used for metal-production and fluorine-recycling. Preliminary results of small scale experiments with different materials are discussed, giving information on specific oxygen-yields and amounts of by-products as functions of temperature. These experiments were performed with an already existing fluorine extraction and collection device at the University of Bonn, normally used for determination of oxygen-isotopic abundances. Optimum conditions, especially concerning energy consumption, are investigated. Extrapolation of the experimental results to large industrial-type plants on the Moon is tried and seems to be promising at first sight. The recycling of the fluorine is, however, crucial for the process. It might be achieved by means of electrolysis. This needs further investigation. The technical problem of transport and handling of the toxic and corrosive fluorine seems to be solvable and could be done by inert storage vessels.

Seboldt, W.↗

NASA NTRS1998

Formation of RNA oligomers on montmorillonite: site of catalysis

Certain montmorillonites catalyze the self condensation of the 5'-phosphorimidazolide of nucleosides in pH 8 aqueous electrolyte solutions at ambient temperatures leading to formation of RNA oligomers. In order to establish the nature of the sites on montmorillonite responsible for this catalytic activity, oligomerization reactions were run with montmorillonites which had been selectively modified (I) at the edges by (a) fluoride treatment, (b) silylation, (c) metaphosphate treatment of the anion exchange sites (II) in the interlayer by (a) saturation with quaternary alkylammonium ions of increasing size, (b) aluminum polyoxo cations. High pressure liquid chromatography, HPLC, analysis of condensation products for their chain lengths and yields indicated that modification at the edges did not affect the catalytic activity to a significant extent, while blocking the interlayer strongly inhibited product formation.

NASA Discipline Exobiology↗

NASA NTRS2001

Neutron dosimetry in low-earth orbit using passive detectors

This paper summarizes neutron dosimetry measurements made by the USF Physics Research Laboratory aboard US and Russian LEO spacecraft over the past 20 years using two types of passive detector. Thermal/resonance neutron detectors exploiting the 6Li(n,T) alpha reaction were used to measure neutrons of energies <1 MeV. Fission foil neutron detectors were used to measure neutrons of energies above 1 MeV. While originally analysed in terms of dose equivalent using the NCRP-38 definition of quality factor, for the purposes of this paper the measured neutron data have been reanalyzed and are presented in terms of ambient dose equivalent. Dose equivalent rate for neutrons <1 MeV ranged from 0.80 microSv/d on the low altitude, low inclination STS-41B mission to 22.0 microSv/d measured in the Shuttle's cargo bay on the highly inclined STS-51F Spacelab-2 mission. In one particular instance a detector embedded within a large hydrogenous mass on STS-61 (in the ECT experiment) measured 34.6 microSv/d. Dose equivalent rate measurements of neutrons >1 MeV ranged from 4.5 microSv/d on the low altitude STS-3 mission to 172 microSv/d on the ~6 year LDEF mission. Thermal neutrons (<0.3 eV) were observed to make a negligible contribution to neutron dose equivalent in all cases. The major fraction of neutron dose equivalent was found to be from neutrons >1 MeV and, on LDEF, neutrons >1 MeV are responsible for over 98% of the total neutron dose equivalent. Estimates of the neutron contribution to the total dose equivalent are somewhat lower than model estimates, ranging from 5.7% at a location under low shielding on LDEF to 18.4% on the highly inclined (82.3 degrees) Biocosmos-2044 mission. c2001 Elsevier Science Ltd. All rights reserved.

Flight Experiment↗

NASA NTRS1996

A Computational Fluid Dynamic and Heat Transfer Model for Gaseous Core and Gas Cooled Space Power and Propulsion Reactors

A computational model based on the axisymmetric, thin-layer Navier-Stokes equations is developed to predict the convective, radiation and conductive heat transfer in high temperature space nuclear reactors. An implicit-explicit, finite volume, MacCormack method in conjunction with the Gauss-Seidel line iteration procedure is utilized to solve the thermal and fluid governing equations. Simulation of coolant and propellant flows in these reactors involves the subsonic and supersonic flows of hydrogen, helium and uranium tetrafluoride under variable boundary conditions. An enthalpy-rebalancing scheme is developed and implemented to enhance and accelerate the rate of convergence when a wall heat flux boundary condition is used. The model also incorporated the Baldwin and Lomax two-layer algebraic turbulence scheme for the calculation of the turbulent kinetic energy and eddy diffusivity of energy. The Rosseland diffusion approximation is used to simulate the radiative energy transfer in the optically thick environment of gas core reactors. The computational model is benchmarked with experimental data on flow separation angle and drag force acting on a suspended sphere in a cylindrical tube. The heat transfer is validated by comparing the computed results with the standard heat transfer correlations predictions. The model is used to simulate flow and heat transfer under a variety of design conditions. The effect of internal heat generation on the heat transfer in the gas core reactors is examined for a variety of power densities, 100 W/cc, 500 W/cc and 1000 W/cc. The maximum temperature, corresponding with the heat generation rates, are 2150 K, 2750 K and 3550 K, respectively. This analysis shows that the maximum temperature is strongly dependent on the value of heat generation rate. It also indicates that a heat generation rate higher than 1000 W/cc is necessary to maintain the gas temperature at about 3500 K, which is typical design temperature required to achieve high efficiency in the gas core reactors. The model is also used to predict the convective and radiation heat fluxes for the gas core reactors. The maximum value of heat flux occurs at the exit of the reactor core. Radiation heat flux increases with higher wall temperature. This behavior is due to the fact that the radiative heat flux is strongly dependent on wall temperature. This study also found that at temperature close to 3500 K the radiative heat flux is comparable with the convective heat flux in a uranium fluoride failed gas core reactor.

Anghaie, S.↗