Search NASA⌕ Search

SEARCH · Search NASA

Results for “HYPERVELOCITY GUN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Intact capture of hypervelocity particles on Shuttle

The capability for capturing micrometeoroid analogs intact through laboratory simulations in passive underdense media offers a valuable tool for cosmic dust research. However, no amount of laboratory simulations can replace actual space experiments due to the technical inability to launch high fidelity analogs of micrometeoroids in ground laboratories and then reliably simulating high hypervelocities (greater than 7 km/s). Fluffy composite micrometeoroid analogs tend to break up and have not survived laboratory launches at beyond 4 km/s, however, a new technique of launching cluster analogs was developed for the two-stage light-gas gun at NASA Ames Vertical Gun Range. Plasma drag or electrostatic accelerators may be able to achieve higher speeds than two-stage light-gas guns but only with very limited projectile compositions and may result in severe projectile deformation. Consequently, a space demonstration of intact capture was sought since 1983. Initial results from our STS-47 flight, which carried the first Shuttle Sample Return Experiment (SRE) with silica aerogel capture media, are reported.

Tsou, P.↗
NASA NTRS1994

Eureka! Aerogel capture of meteoroids in space

Light gas gun studies have shown that 6 km/s solid mineral and glass test particles can be successively captured in 0.05 g cm(exp -3) aerogel without severe heating or fragmentation. In spite of this work, there has been uncertainty in the performance of aerogel for hypervelocity capture of real meteoroids. Natural impacts differ from simulations in that the particles are likely to be structurally weak and they typically impact at higher velocity that can be simulated in the laboratory. We are fortunate now to have had two successful capture experiments using aerogel exposed in space. These experiments provide fundamental data for the assessment of the value of silica aerogel for capture of hypervelocity meteoroids from spacecraft. The first experiment used 0.02 g cm(exp -3) aerogel flown on the lid of a Shuttle Get Away Special canister. During its 9 day exposure, the 0.165 m(exp 2) of aerogel in this Sample Return Experiment (SRE) captured two long 'carrot-shaped' tracks and one highly fractured bowl shaped 'crater'. The second collection was with 0.04 m(exp 2) of 0.05 g cm(exp -3) aerogel exposed on ESA's Eureca freeflying spacecraft that was exposed for 11 months before recovery by the Shuttle. The Eureca aerogel exposure consisted of four 10x10 cm module trays that were part of the TiCCE meteoroid collector built by the University of Kent at Canterbury. To date we have found ten 'carrot-shaped' tracks and two 'craters' on this experiment. The longest tracks in both exposures are over 2 mm long. Two of the TiCCE modules had a 0.1 micron Al film suspended a millimeter above the aerogel. On these modules several of the projectiles fragmented during passage through the film producing fields of carrot shaped tracks from the resulting miniature 'meteor' shower. Most of the tracks in these showers have observable particles at their ends. We have extracted one of the carrot track meteoroids and mounted it in epoxy for sectioning. So far the examination of these 14 impacts suggests that low density aerogel is a magic and highly effective media for intact capture of hypervelocity particles in space.

Brownlee, D. E.↗
NASA NTRS2010

Performance of Waterless Concrete

The development of permanent lunar bases is constrained by performance of construction materials and availability of in-situ resources. Concrete seems a suitable construction material for the lunar environment, but water, one of its major components, is an extremely scarce resource on the Moon. This study explores an alternative to hydraulic concrete by replacing the binding mix of concrete (cement and water) with sulfur. Sulfur is a volatile element on the lunar surface that can be extracted from lunar soils by heating. Sulfur concrete mixes were prepared to investigate the effect of extreme environmental conditions on the properties of sulfur concrete. A hypervelocity impact test was conducted, having as its target a 5-cm cubic sample of sulfur concrete. This item consisted of JSC-1 lunar regolith simulant (65%) and sulfur (35%). The sample was placed in the MSFC Impact Test Facility s Micro Light Gas Gun target chamber, and was struck by a 1-mm diameter (~1.4e-03 g) aluminum projectile at 5.85 km/s. In addition, HZTERN code, provided by NASA was used to study the effectiveness of sulfur concrete when subjected to space radiation.

Toutanji, Houssam↗
NASA NTRS1993

Repeatability and uncertainty analyses of NASA/MSFC light gas gun test data

This Final Report presents an overview of the impact tests performed at NASA/MSFC in the time period 1985 to 1991 and the results of phenomena repeatability and data uncertainty studies performed using the information obtained from those tests. An analysis of the data from over 400 tests conducted between 1989 and 1991 was performed to generate a database to supplement the Hypervelocity Impact Damage Database developed under a previous effort.

Schonberg, William P.↗
NASA NTRS2014

New Laboratory-Based Satellite Impact Experiments for Breakup Fragment Characterization

A consortium consisting of the NASA Orbital Debris Program Office, U.S. Air Force's Space and Missile Systems Center, the Aerospace Corporation, and University of Florida is planning a series of hypervelocity impact experiments on mockup targets at the U.S. Air Force's Arnold Engineering Development Complex (AEDC) in early 2014. The target for the first experiment resembles a rocket upper stage whereas the target for the second experiment represents a typical 60‐cm/50‐kg class payload that incorporates modern spacecraft materials and components as well as exterior wrap of multi‐layer insulation and three solar panels. The projectile is designed with the maximum mass that AEDC's Range G two‐stage light gas gun can accelerate to an impact speed of 7 km/sec. The impact energy is expected to be close to 15 MJ to ensure catastrophic destruction of the target after the impact. Low density foam panels are installed inside the target chamber to slow down and soft‐catch the fragments for post‐impact processing. Diagnostic instruments, such as x‐ray and high speed optical cameras, will also be used to record the breakup process. The main goal of this "DebriSat" project is to characterize the physical properties, including size, mass, shape, and density distributions, of orbital debris that would be generated by a hypervelocity collision involving an upper stage or a modern satellite in the low Earth orbit environment. In addition, representative fragments will be selected for laboratory optical and radar measurements to allow for better interpretation of data obtained by telescope and radar observations. This paper will provide a preliminary report of the impact results and the plans to process, measure, and analyze the fragments.

Liou, J.-C.↗
NASA NTRS1961

A Technique for Obtaining Hypervelocity Impact Data by using the Relative Velocities of Two Projectiles

A facility has been developed and put into operation to determine the feasibility of obtaining hypervelocity impact data by using the relative velocities of two projectiles. The facility utilizes the technique of firing a target toward an oncoming high-velocity projectile so that the impact velocity is equal to the sum of the projectile velocity and the target velocity. A 37-millimeter powder gun is utilized to accelerate the targets, and a specially designed 22-caliber light-gas gun accelerates the impacting projectiles. The light-gas gun is operated by detonating an explosive charge which permits it to be synchronized with the firing of the 37-millimeter gun. Impact velocities as great as 21,850 ft/sec have been obtained during development of the facility. After the oncoming projectiles impact the targets fired from the 37-millimeter gun, these targets are recovered by allowing them to impact into Celotex and soft wooden blocks. The craters formed in the targets then can be observed and measured. The results of several preliminary firings of the facility are included in this report.

Kinard, William H.↗
NASA NTRS2013

Sabots, Obturator and Gas-In-Launch Tube Techniques for Heat Flux Models in Ballistic Ranges

For thermal protection system (heat shield) design for space vehicle entry into earth and other planetary atmospheres, it is essential to know the augmentation of the heat flux due to vehicle surface roughness. At the NASA Ames Hypervelocity Free Flight Aerodynamic Facility (HFFAF) ballistic range, a campaign of heat flux studies on rough models, using infrared camera techniques, has been initiated. Several phenomena can interfere with obtaining good heat flux data when using this measuring technique. These include leakage of the hot drive gas in the gun barrel through joints in the sabot (model carrier) to create spurious thermal imprints on the model forebody, deposition of sabot material on the model forebody, thereby changing the thermal properties of the model surface and unknown in-barrel heating of the model. This report presents developments in launch techniques to greatly reduce or eliminate these problems. The techniques include the use of obturator cups behind the launch package, enclosed versus open front sabot designs and the use of hydrogen gas in the launch tube. Attention also had to be paid to the problem of the obturator drafting behind the model and impacting the model. Of the techniques presented, the obturator cups and hydrogen in the launch tube were successful when properly implemented

obturators↗
NASA NTRS1991

Empirical predictions of hypervelocity impact damage to the space station

A family of user-friendly, DOS PC based, Microsoft BASIC programs written to provide spacecraft designers with empirical predictions of space debris damage to orbiting spacecraft is described. The spacecraft wall configuration is assumed to consist of multilayer insulation (MLI) placed between a Whipple style bumper and the pressure wall. Predictions are based on data sets of experimental results obtained from simulating debris impacts on spacecraft using light gas guns on Earth. A module of the program facilitates the creation of the data base of experimental results that are used by the damage prediction modules of the code. The user has the choice of three different prediction modules to predict damage to the bumper, the MLI, and the pressure wall. One prediction module is based on fitting low order polynomials through subsets of the experimental data. Another prediction module fits functions based on nondimensional parameters through the data. The last prediction technique is a unique approach that is based on weighting the experimental data according to the distance from the design point.

Rule, W. K.↗
NASA NTRS1992

Investigation of the aerothermodynamics of hypervelocity reacting flows in the ram accelerator

New diagnostic techniques for measuring the high pressure flow fields associated with high velocity ram accelerator propulsive modes was experimentally investigated. Individual propulsive modes are distinguished by their operating Mach number range and the manner in which the combustion process is initiated and stabilized. Operation of the thermally choked ram accelerator mode begins by injecting the projectile into the accelerator tube at a prescribed entrance velocity by means of a conventional light gas gun. A specially designed obturator, which is used to seal the bore of the gun, plays a key role in the ignition of the propellant gases in the subsonic combustion mode of the ram accelerator. Once ignited, the combustion process travels with the projectile and releases enough heat to thermally choke the flow within several tube diameters behind it, thereby stabilizing a high pressure zone on the rear of the projectile. When the accelerating projectile approaches the Chapman-Jouguet detonation speed of the propellant mixture, the combustion region is observed to move up onto the afterbody of the projectile as the pressure field evolves to a distinctively different form that implies the presence of supersonic combustion processes. Eventually, a high enough Mach number is reached that the ram effect is sufficient to cause the combustion process to occur entirely on the body. Propulsive cycles utilizing on-body heat release can be established either by continuously accelerating the projectile in a single propellant mixture from low initial in-tube Mach numbers (M less than 4) or by injecting the projectile at a speed above the propellant's Chapman-Jouguet detonation speed. The results of experimental and theoretical explorations of ram accelerator gas dynamic phenomena and the effectiveness of the new diagnostic techniques are presented in this report.

Hertzberg, A.↗
NASA NTRS1991

An advanced hypervelocity aerophysics facility - A ground-based flight-test range

The paper discusses a concept for a ground-based flight-test facility, a large aeroballistic range capable of launching models large enough to permit the installation of significant amounts of onboard instrumentation. The large model size would also provide thick shock/boundary layers, thus providing the opportunity to measure flow-field properties via advanced offboard diagnostics. Current fabrication technology should permit the construction of a two-stage light-gas gun capable of accelerating 20 to 25 cm diameter models to velocities on the order of 6 km/sec. An electromagnetic launcher or a ram accelerator is considered as a potential means for achieving larger model sizes and/or greater launch velocities. Possible methods for obtaining and recording data are discussed as are the test chamber and model deceleration section requirements.

Witcofski, R. D.↗
NASA NTRS2006

Focused Ion Beam Recovery of Hypervelocity Impact Residue in Experimental Craters on Metallic Foils

The Stardust sample return capsule will return to Earth in January 2006 with primitive debris collected from Comet 81P/Wild-2 during the fly-by encounter in 2004. In addition to the cometary particles embedded in low-density silica aerogel, there will be microcraters preserved in the Al foils (1100 series; 100 micrometers thick) that are wrapped around the sample tray assembly. Soda lime spheres (approximately 49 m in diameter) have been accelerated with a light-gas-gun into flight-grade Al foils at 6.35 km s(sup -1) to simulate the potential capture of cometary debris. The preserved crater penetrations have been analyzed using scanning electron microscopy (SEM) and x-ray energy dispersive spectroscopy (EDX) to locate and characterize remnants of the projectile material remaining within the craters. In addition, ion beam induced secondary electron imaging has proven particularly useful in identifying areas within the craters that contain residue material. Finally, high-precision focused ion beam (FIB) milling has been used to isolate and then extract an individual melt residue droplet from the interior wall of an impact penetration. This enabled further detailed elemental characterization, free from the background contamination of the Al foil substrate. The ability to recover pure melt residues using FIB will significantly extend the interpretations of the residue chemistry preserved in the Al foils returned by Stardust.

Graham, G. A.↗
NASA NTRS2016

IADC Vulnerability Report, IT32-21

Numerous mission support hardware systems and their spares are maintained outside of the habitable volume of the International Space Station (ISS), and are arranged covered by a multi-layer insulation (MLI) thermal blanket which provides both thermal control and a measure of protection from micrometeoroids and orbital debris (MMOD). The NASA Hypervelocity Impact Technology (HVIT) group at the Johnson Space Center in Houston Texas has assessed the protection provided by MLI in a series of hypervelocity impact tests using a 1 mm thick aluminum 6061-T6 rear wall to simulate the actual hardware behind the MLI. HVIT has also evaluated methods to enhance the protection provided by MLI thermal blankets. The impact study used both aluminum and steel spherical projectiles accelerated to speeds of 7 km/s using a 4.3 mm, two-stage, light-gas gun at the NASA White Sands Test Facility (WSTF).

Christiansen, E. L.↗
NASA NTRS1991

MLITemp: A computer program to predict the thermal effects associated with hypervelocity impact damage to space station MLI

A family of user-friendly, DOS PC based, Microsoft BASIC programs written to provide spacecraft designers with empirical predictions of space debris damage to orbiting spacecraft are described. Spacecraft wall temperatures and condensate formation is also predicted. The spacecraft wall configuration is assumed to consist of multilayered insulation (MLI) placed between a Whipple style bumper and the pressure wall. Impact damage predictions are based on data sets of experimental results obtained from simulating debris impacts on spacecraft using light gas guns on earth. A module of the program facilitates the creation of the database of experimental results that is used by the damage prediction modules to predict damage to the bumper, the MLI, and the pressure wall. A finite difference technique is used to predict temperature distributions in the pressure wall, the MLI, and the bumper. Condensate layer thickness is predicted for the case where the pressure wall temperature drops below the dew point temperature of the spacecraft atmosphere.

Rule, W. K.↗
NASA NTRS1994

The hypervelocity impact facilities at the University of Kent at Canterbury, UK

The University of Kent at Canterbury facilities for production of hypervelocity impacts are discussed. Meteoroids are simulated by electrostatic acceleration of small (10(exp -12) - 10(exp -17) kg) particles using a 2-MV Van de Graaff accelerator. This machine has been operational for many years; both the machine and experimental area are currently being upgraded. Larger particles (10(exp -10) - 10(exp -14) kg) are accelerated using a more recently installed light gas gun. The status of all hardware (including experimental areas) is given, along with brief details of recent, current, and future projects making use of them.

Burchell, Mark J.↗
NASA NTRS1988

The ballistic range and aerothermodynamic testing

A renewed interest in hypervelocity vehicles requires an increase in our knowledge of aerothermodynamic phenomena. Tests conducted in our ground-based facilities can be used both to better understand the physics of hypervelocity flight, and to calibrate and validate computer codes designed to predict vehicle performance in the hypervelocity environment. This paper reviews the requirements for aerothermodynamic testing and discusses the ballistic range and its capabilities. Examples of the kinds of testing performed in typical high-performance ballistic ranges are described; we draw heavily on experience obtained in the ballistics facilities at NASA Ames. Prospects for improving the capabilities of the ballistic range by using advanced instrumentation are discussed. Finally, recent developments in gun technology and their application to extend the capability of the ballistic range are summarized.

Strawa, A. W.↗
NASA NTRS2010

Secondary Impacts on Structures on the Lunar Surface

The Altair Lunar Lander is being designed for the planned return to the Moon by 2020. Since it is hoped that lander components will be re-used by later missions, studies are underway to examine the exposure threat to the lander sitting on the Lunar surface for extended periods. These threats involve both direct strikes of meteoroids on the vehicle as well as strikes from Lunar regolith and rock thrown by nearby meteorite strikes. Currently, the lander design is comprised of up to 10 different types of pressure vessels. These vessels included the manned habitation module, fuel, cryogenic fuel and gas storage containers, and instrument bays. These pressure vessels have various wall designs, including various aluminum alloys, honeycomb, and carbon-fiber composite materials. For some of the vessels, shielding is being considered. This program involved the test and analysis of six pressure vessel designs, one of which included a Whipple bumper shield. In addition to the pressure vessel walls, all the pressure vessels are wrapped in multi-layer insulation (MLI). Two variants were tested without the MLI to better understand the role of the MLI in the impact performance. The tests of performed were to examine the secondary impacts on these structures as they rested on the Lunar surface. If a hypervelocity meteor were to strike the surface nearby, it would throw regolith and rock debris into the structure at a much lower velocity. Also, when the manned module departs for the return to Earth, its rocket engines throw up debris that can impact the remaining lander components and cause damage. Glass spheres were used as a stimulant for the regolith material. Impact tests were performed with a gas gun to find the V50 of various sized spheres striking the pressure vessels. The impacts were then modeled and a fast-running approximate model for the V50 data was developed. This model was for performing risk analysis to assist in the vessel design and in the identification of ideal long-term mission sites. This paper reviews the impact tests and analysis and modeling examining the impact threat to various components in the lander design.

Christiansen, Eric↗
NASA NTRS1988

A research study for the preliminary definition of an aerophysics free-flight laboratory facility

A renewed interest in hypervelocity vehicles requires an increase in the knowledge of aerodynamic phenomena. Tests conducted with ground-based facilities can be used both to better understand the physics of hypervelocity flight, and to calibrate and validate computer codes designed to predict vehicle performance in the hypervelocity environment. This research reviews the requirements for aerothermodynamic testing and discusses the ballistic range and its capabilities. Examples of the kinds of testing performed in typical high performance ballistic ranges are described. We draw heavily on experience obtained in the ballistics facilities at NASA Ames Research Center, Moffett Field, California. Prospects for improving the capabilities of the ballistic range by using advanced instrumentation are discussed. Finally, recent developments in gun technology and their application to extend the capability of the ballistic range are summarized.

Canning, Thomas N.↗
NASA NTRS1986

A planetary ultra hypervelocity impact mechanics and shock wave science facility

Using the concept of intercepting orbits from a pair of Space Station serviced free flyers, a class of impact and shock wave experiments pertinent to planetary science can be performed. One proposed free flying vehicle is an impactor dispensor, and the second is the impact laboratory. How collision is achieved by utilizing essentially twice orbital velocity is demonstrated. The impactor dispensor contains a series of small flyer plates or other projectiles which are launched into the trajectory of the impactor laboratory at appropriate positions. The impactor laboratory is a large impact tank similar to those in terrestrial gun laboratories, except that it contains a supply of targets and instrumentation such as high speed cameras, flash X-ray apparatus and digital recorders. Shock and isentropic pressures of up to 20 Mbar are achievable with such a system which provides 15 km/sec impact velocities for precisely oriented projectiles.

Ahrens, T. J.↗