Application of a method of estimating high- temperature low-cycle fatigue behavior of materials.
Metal alloys high temperature low cycle strain fatigue resistance in creep range estimated from tensile and stress rupture data
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Metal alloys high temperature low cycle strain fatigue resistance in creep range estimated from tensile and stress rupture data
Abstract not provided
Highlights: • High temperature solid state reaction, hydrothermal, sol-gel methods were applied. • All ZnGa{sub 2}O{sub 4} samples show UV-light catalytic activities on pure water splitting. • Bulk ZnGa{sub 2}O{sub 4} has a good photocatalytic activity per specific surface area. • Sol-gel is a superior method to prepare nanosized ZnGa{sub 2}O{sub 4} with a high activity. • The AQY for SG-ZnGa{sub 2}O{sub 4} is 2.6% for pure water splitting under 313 nm irradiation. - Abstract: We studied and compared the photocatalytic water splitting performances for ZnGa{sub 2}O{sub 4} prepared by high temperature solid state reaction (HTSSR), hydrothermal (HY) and sol-gel (SG) methods. HTSSR-ZnGa{sub 2}O{sub 4} has a relative large photocatalytic activity per surface area (1.6 μmol/h/m{sup 2}) in pure water by UV irradiation due to its high crystallinity. The HY- and SG-samples both have small particle sizes (20∼30 nm) and therefore high surface area (20 and 29 m{sup 2}/g, respectively), which leads to superior photocatalytic H{sub 2} evolution rates per unit mass (11.5 and 28.5 μmol/h/g). The apparent quantum yield of SG-ZnGa{sub 2}O{sub 4} for pure water splitting under 313 nm irradiation is 2.6%. The existence of substantial surface defects is the major problem for HY- and SG-ZnGa{sub 2}O{sub 4}. Consequently, the usage of sacrificial agents could greatly enhance the activities and indeed the H{sub 2} evolution rates in 20 Vol. % methanol aqueous solution increase to 100 and 142 μmol/h/g for HY- and SG-ZnGa{sub 2}O{sub 4}, respectively.
A method of installing fragile, light-weight, high-temperature fiber insulation, particularly where the insulation is to be used as a seal strip providing a high order of thermal barrier insulation is described. The process is based on provision of a strip of the mineral batting cut oversize by a predetermined amount, saturated in a fugitive polymer solution, compressed in a mold, dried and cured to form a rigidized batting material which may be machined to required shape. The machined dimensions would normally be at least nominally less than the dimensions of the cavity to be sealed. After insertion in the cavity, which may be a wire-mesh seal enclosure, the apparatus is subjected to baking at a temperature sufficiently high to cause the resin to burn off cleanly, leaving the batting substantially in its original condition and expanded into the cavity or seal enclosure.
A layered article of manufacture and a method of manufacturing same is disclosed. A substrate has a biaxially textured MgO crystalline layer having the c-axes thereof inclined with respect to the plane of the substrate deposited thereon. A layer of one or more of YSZ or Y.sub.2O.sub.3 and then a layer of CeO.sub.2 is deposited on the MgO. A crystalline superconductor layer with the c-axes thereof normal to the plane of the substrate is deposited on the CeO.sub.2 layer. Deposition of the MgO layer on the substrate is by the inclined substrate deposition method developed at Argonne National Laboratory. Preferably, the MgO has the c-axes thereof inclined with respect to the normal to the substrate in the range of from about 10.degree. to about 40.degree. and YBCO superconductors are used.
Adaptation of the superelement finite-element method for micromechanics of continuous fiber high temperature metal matrix composites (HT-MMC) is described. The method is used to predict the thermomechanical behavior of P100-graphite/copper composites using MSC/NASTRAN and it is also used to validate those predicted by using an in-house computer program designed to perform micromechanics for HT-MMC. Typical results presented in the paper include unidirectional composite thermal properties, mechanical properties, and microstresses.
Abstract The incorporation of SiOC polymer‐derived ceramics into porous carbon materials could provide tailored shapeable, mechanical, electrical, and oxidation‐resistant properties for high‐temperature applications. Understanding the thermodynamic and kinetic stability of such materials is crucial for their practical application. We report here the dependence of structures and energetics of SiOC and SiOC ‐modified carbon‐bonded carbon fiber composites ( CBCFs ) on the pyrolysis temperature using spectroscopic methods and high‐temperature oxide melt solution calorimetry. The results indicate that a SiOC ceramic pyrolyzed at 1200°C and 1600°C is energetically stable with respect to an isocompositional mixture of cristobalite, silicon carbide, and graphite by 4.9 and 10.3 kJ/mol, respectively, and more energetically stable than that pyrolyzed at 1450°C. Their thermodynamic stability is related to their structural evolution. SiOC ‐modified CBCF s become energetically less stable with increasing preparation temperature and concomitant increase in excess carbon content.
A method of fabricating large bulk high temperature superconducting articles which comprises the steps of selecting predetermined sizes of crystalline superconducting materials and mixing these specific sizes of particles into a homogeneous mixture which is then poured into a die. The die is placed in a press and pressurized to predetermined pressure for a predetermined time and is heat treated in the furnace at predetermined temperatures for a predetermined time. The article is left in the furnace to soak at predetermined temperatures for a predetermined period of time and is oxygenated by an oxygen source during the soaking period.
A dipole-magnet system and method for producing high-magnetic-fields, including an open-region located in a radially-central-region to allow particle-beam transport and other uses, low-temperature-superconducting-coils comprised of low-temperature-superconducting-wire located in radially-outward-regions to generate high magnetic-fields, high-temperature-superconducting-coils comprised of high-temperature-superconducting-tape located in radially-inward-regions to generate even higher magnetic-fields and to reduce erroneous fields, support-structures to support the coils against large Lorentz-forces, a liquid-helium-system to cool the coils, and electrical-contacts to allow electric-current into and out of the coils. The high-temperature-superconducting-tape may be comprised of bismuth-strontium-calcium-copper-oxide or rare-earth-metal, barium-copper-oxide (ReBCO) where the rare-earth-metal may be yttrium, samarium, neodymium, or gadolinium. Advantageously, alignment of the large-dimension of the rectangular-cross-section or curved-cross-section of the high-temperature-superconducting-tape with the high-magnetic-field minimizes unwanted erroneous magnetic fields. Alignment may be accomplished by proper positioning, tilting the high-temperature-superconducting-coils, forming the high-temperature-superconducting-coils into a curved-cross-section, placing nonconducting wedge-shaped-material between windings, placing nonconducting curved-and-wedge-shaped-material between windings, or by a combination of these techniques.
Chemically inert, aluminosilicate based particles have been investigated as both a thermal transport and sensible energy storage medium for concentrated solar power facilities. These particles will experience a wide range of operating temperatures (300-1000 K) and handling conditions (dense to dilute falling particle curtains, dense granular flows, or dense structures), requiring specially-designed and optimized infrastructures. The relative influence of collisional and frictional interactions between particles varies based on temperature-dependent particulate properties and greatly impacts the bulk, granular flow behavior. These underlying physics are captured using discrete element method modeling tools. However, this modeling method is computationally expensive as each particle position and interaction is tracked during the simulation. These modeling methods are further complicated by introducing temperature-dependent particle properties, high-temperature radiative exchange, and directional irradiation sources experienced by granular flows in concentrated solar power environments. Coupled experimental and numerical studies of aluminosilicate particles in rotary kilns and dense particle curtains were performed for bulk temperatures up to 1073 K. The three particle types investigated included Carbobead HSP 30 /60, Carbobead CP 30/60, and Granusil 4030. Temperature, spatial, and velocity profile data were extracted from experimental runs using embedded K-type thermocouple probes and particle image velocimetry techniques. Experimental and numerical studies were compared using spatial temperature profiles, velocity fields, and shape profiles of the bulk, granular flows. Numerical models were developed using commercially available discrete element method modeling software, Aspherix®. Existing Aspherix® functionality was expanded by introducing coupled radiative exchange modeling tools. The laboratory-scale rotary kiln was developed to investigate the steady-state heat and mass transfer performance of aluminosilicate particles based on particle type, bulk handling temperature, and wall roughness. The rotational speed of the rotary kiln was varied to control the relative impact of collisional and frictional effects upon the granular flow behavior. Heat and mass transfer performance was categorized based on the Froude number and the observed flow regimes of slipping, rolling, cascading, and centrifuging. Coupled discrete element method modeling studies were used to evaluate the effects of temperature-dependent, particulate mechanical properties upon bulk flow behavior and upon the relative effects of radiative, advective, and/or conductive heat transfer. A high-temperature (< 1073 K) falling particle curtain was similarly fabricated to investigate the heat and mass transfer performance of aluminosilicate particles in particle handling situations dominated by inter-particle collisions. The impact of particle type, flow preheat temperatures (< 1073K), and bulk mass flow rates were investigated upon the particle curtain shape, temperature, and velocity profiles. Coupled discrete element method modeling studies were performed to evaluate the varying impact of temperature-dependent, particulate mechanical properties on the bulk flow behavior and the temperature profile of the particle curtain.
Introduction: Our novel high pressure, high temperature synthesis method produces white, highly crystalline, small diameter, long BNNTs without any catalyst. The quality of BNNTs will be optimized by understanding the nucleation and growth mechanism of BNNT through coherent computational modeling and in-situ and ex-situ experiments. Both BNNT production and science rigs operational. Goals and Objectives: Produce high quality, large quantity BNNTs and BNNT fibers for use as reinforcements for polymer, ceramic, and metallic matrices and assess the scale-ability of existing synthesis methods for large scale production of these reinforcements. Deliverable: High quality optimized BNNT synthesis method and systematic property database of BNNT composites. Fabrication and analysis of non-woven mats, fibers, yarns and composites to evaluate their structural and functional properties.
In the past, high temperature specific heat and hence thermal conductivity measurements, using the flash method have not been very accurate. This is due to the difficulty of exactly determining the amount of heat deposited on the front face of a sample during each flash. This problem has now been solved by sputtering a thin layer of graphite on the standard reference and test samples. Data taken shows that the amount of heat deposited can now be determined to within about 2 percent resulting in more accurate thermal conductivity data. The results of measurements on several lanthanum sulfides with stoichiometries between LaS(1.35) and LaS(1.48) are reported and show a minimum in the lattice thermal conductivity at a composition of around LaS(1.41). This is believed to be due to the scattering of low-frequency phonons by large defects, i.e., second phase material (beta-phase) and pores.
A new metal coating method, cidled KEM (kinetic energy metal.lization), demonstrated in the laboratory by lnovati, utilized fast-moving solid particIes entrained in a gas that are caused to fiow through a nozzIe to effect particle deposition on metal surfaces at room temperature conditions. This method (US Patent 5,795,626) was an attractive and viabIe alternative to the currentIy available high-temperature coating methods avaiIabIe. Since it differs significantly from existing metal coating technologies, a brief description of the method is incIuded here. The proposed method, KEM, achieves cohesive and adhesive metallurgical bonding through the high-speed coUision of powder with a substrate and the subsequent discharge of electrical charge at the substrate. Such coating is effected by entraining metal powder in a gas and accelerating this mixture through a supersonic nozzle. The gas/powder is directed towards the substrate to be coated. Collisions occur, initiaIly between the powder and the substrate, and, as the first Iayer of the coating forms, between the powder and the coating. During these collisions the powder is rapidly deformed, causing the exposure of fresh (oxide free) active metal surface. When these’active surfaces contact one another, they agglomerate and form true metaIIurgicaI bonds. The resultant coating has Iow porosity and high adhesive and cohesive strength. The formation of metaIIurgicaI bonds is potentiated by the discharge of electrical energy. This electrical energy is the result of triboeIectric charging of the particIes during acceleration and transit to the nozzIe. An advantage of the method is that it does not raise the temperature of the powder being appLiedor that of the substrate. Consequently, materials sensitive to high temperature may be applied without changing Me properties of the materkd or substrate.
An air-ingress accident followed by a pipe break is considered as a critical event for a very high temperature gas-cooled reactor (VHTR). Following helium depressurization, it is anticipated that unless countermeasures are taken, air will enter the core through the break leading to oxidation of the in-core graphite structure. Thus, without mitigation features, this accident might lead to severe exothermic chemical reactions of graphite and oxygen. Under extreme circumstances, a loss of core structural integrity may occur along with excessive release of radiological inventory. Idaho National Laboratory under the auspices of the U.S. Department of Energy is performing research and development (R&D) that focuses on key phenomena important during challenging scenarios that may occur in the VHTR. Phenomena Identification and Ranking Table (PIRT) studies to date have identified the air ingress event, following on the heels of a VHTR depressurization, as very important (Oh et al. 2006, Schultz et al. 2006). Consequently, the development of advanced air ingress-related models and verification and validation (V&V) requirements are part of the experimental validation plan. This paper discusses about various air-ingress mitigation concepts applicable for the VHTRs. The study begins with identifying important factors (or phenomena) associated with the air-ingress accident by using a root-cause analysis. By preventing main causes of the important events identified in the root-cause diagram, the basic air-ingress mitigation ideas can be conceptually derived. The main concepts include (1) preventing structural degradation of graphite supporters; (2) preventing local stress concentration in the supporter; (3) preventing graphite oxidation; (4) preventing air ingress; (5) preventing density gradient driven flow; (4) preventing fluid density gradient; (5) preventing fluid temperature gradient; (6) preventing high temperature. Based on the basic concepts listed above, various air-ingress mitigation methods are proposed in this study. Among them, the following two mitigation ideas are extensively investigated using computational fluid dynamic codes (CFD): (1) helium injection in the lower plenum, and (2) reactor enclosure opened at the bottom. The main idea of the helium injection method is to replace air in the core and the lower plenum upper part by buoyancy force. This method reduces graphite oxidation damage in the severe locations of the reactor inside. To validate this method, CFD simulations are addressed here. A simple 2-D CFD model is developed based on the GT-MHR 600MWt design. The simulation results showed that the helium replace the air flow into the core and significantly reduce the air concentration in the core and bottom reflector potentially protecting oxidation damage. According to the simulation results, even small helium flow was sufficient to remove air in the core, mitigating the air-ingress successfully. The idea of the reactor enclosure with an opening at the bottom changes overall air-ingress mechanism from natural convection to molecular diffusion. This method can be applied to the current system by some design modification of the reactor cavity. To validate this concept, this study also uses CFD simulations based on the simplified 2-D geometry. The simulation results showed that the enclosure open at the bottom can successfully mitigate air-ingress into the reactor even after on-set natural circulation occurs.
A system and method for monitoring the properties of a fluid, such as water, in a steam pipe without mechanically penetrating the wall of the pipe. The system uses a piezoelectric transducer to launch an ultrasonic probe signal into the pipe. Reflected ultrasonic signals are captured in a transducer, which can be the same transducer that launched the probe signal. The reflected signals are subjected to data processing, which can include filtering, amplification, analog-to-digital conversion and autocorrelation analysis. A result is extracted which is indicative of a property of the fluid, such as a height of the condensed fluid, a cavitation of the condensed fluid, and a surface perturbation of the condensed fluid. The result can be recorded, displayed, and/or transmitted to another location. One embodiment of the system has been constructed and tested based on a general purpose programmable computer using instructions recorded in machine-readable non-volatile memory.
A novel, open-source radiative modeling toolset was developed to extend the functionality of particle-based modeling software (e.g. discrete element method (DEM)) to environmental conditions relevant to concentrated solar power applications. This toolset was optimized for deployment on desktop workstations instead of high-performance computing systems, to render such tools more accessible to the research community. Both particle-based modeling and radiative exchange modeling are computationally expensive and often require specialized programming expertise, making these methods cumbersome to use. Recent developments in DEM software by DCS Computing have greatly reduced these challenges, providing a graphical-user-interface based platform and modeling optimization for desktop workstations, HPCs, and cloud computing. The University of Dayton leveraged the experience of DCS Computing in developing a user-friendly, open-source radiative heat transfer expansion for DEM modeling. The University of Dayton DEM+ radiative modeling toolset was developed using a combination of fundamental experimental measurements, modeling, and simplified flow experiments over a range of temperatures and flow conditions. The toolset provides researchers with access to multiple radiative models including an accelerated Monte-Carlo Ray Tracing (application agnostic, highly computationally expensive), an expanded database of distance-based approximations (application limited, computationally light), and a weighted blending of the two methods capable of achieving over 90% reduction in computation time with equivalent accuracy compared to Monte-Carlo Ray Tracing. Through a graphical user interface, users can customize the radiative models to match their desired accuracy and available computational resources, improving access to particle based modeling for the research community. Ceramic sintered bauxite proppants were used in modeling and experimentally as a baseline. Both the radiative heat transfer and flow properties for particulate systems were investigated at elevated temperatures up to 800 °C. The major accomplishments for this work include a verified, open-source radiative modeling toolset to be distributed amongst the research community and the fabrication of three small-scale test facilities to investigate particle behavior and tune DEM flow properties for operation up to 800 °C. The findings have been shared with the research community via conference modeling workshops, deployment of the tools in DCS Computing Aspherix®, and open-source access to the developed radiative modeling tool. The development of next-generation CSP facilities and thermal energy storage systems based on ceramic particles requires providing access to computationally efficient and accurate modeling tools. Particles will experience a wide range of environments (20-800 °C) and handling conditions (dilute curtains or dense packing), requiring specially designed and optimized equipment. Optimizing solid particle physics models and establishing best-practices for particle modeling in CSP environments will assist researchers with designing optimized equipment, accelerating the deployment of more economically-competitive CSP facilities.
Ultrasonic test methods used to determine transport properties of high temperature gases
High electron temperature plasmas with steep temperature gradient in the core are obtained in recent experiments in the Large Helical Device [A. Komori et al., Fusion Sci. Technol. 58, 1 (2010)]. Such plasmas are called core electron-root confinement (CERC) and have attracted much attention. In typical CERC plasmas, the radial electric field shows a transition phenomenon from a small negative value (ion root) to a large positive value (electron root) and the radial electric field in helical plasmas are determined dominantly by the ambipolar condition of neoclassical particle flux. To investigate such plasmas' neoclassical transport precisely, the numerical neoclassical transport code, FORTEC-3D [S. Satake et al., J. Plasma Fusion Res. 1, 002 (2006)], which solves drift kinetic equation based on {delta}f Monte Carlo method and has been applied for ion species so far, is extended to treat electron neoclassical transport. To check the validity of our new FORTEC-3D code, benchmark calculations are carried out with GSRAKE [C. D. Beidler et al., Plasma Phys. Controlled Fusion 43, 1131 (2001)] and DCOM/NNW [A. Wakasa et al., Jpn. J. Appl. Phys. 46, 1157 (2007)] codes which calculate neoclassical transport using certain approximations. The benchmark calculation shows a good agreement among FORTEC-3D, GSRAKE and DCOM/NNW codes for a low temperature (T{sub e}(0)=1.0 keV) plasma. It is also confirmed that finite orbit width effect included in FORTEC-3D affects little neoclassical transport even for the low collisionality plasma if the plasma is at the low temperature. However, for a higher temperature (5 keV at the core) plasma, significant difference arises among FORTEC-3D, GSRAKE, and DCOM/NNW. These results show an importance to evaluate electron neoclassical transport by solving the kinetic equation rigorously including effect of finite radial drift for high electron temperature plasmas.