Search NASA⌕ Search

SEARCH · Search NASA

Results for “IMIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Super p-sulfur cathodes for quasi-solid-state lithium-sulfur-batteries

Lithium-Sulfur (Li-S) batteries have become a promising candidate to meet the current energy storage demand, with its natural abundance of materials, high theoretical capacity of 1672 mAhg-1, high energy density of 2600 Whkg-1, low cost and lower environmental impact. Sulfide based solid state electrolytes (SSEs) have received greater attention due to their higher ionic conductivity, compatible interface with sulfur-based cathodes, and lower grain boundary resistance. However, the interface between SSEs and cathodes has become a challenge in all solid-state Li-S batteries due to the rigidity of the participating surfaces. A hybrid electrolyte containing SSE coupled with a small amount of ionic liquid, was essential to improve the interface contact of the SSE with the electrodes. Coating-based cathodes were successfully fabricated using water-based carboxymethyl cellulose (CMC) solution and Styrene butadiene rubber (SBR) as the binder with low sulfur loading (0.70 mgcm-2) as well as high sulfur loading (4.0 mgcm-2). Solid-state composite powder-based cathodes pressed onto SSE (loading 4.0 mgcm-2) with enhanced electronic and ionic conductivity were fabricated with Super P: Sulfur (SP:S) and SSE. Ionic Liquids (IL) prepared using Lithium bis(trifluoromethyl sulfonyl)imide (LiTFSI) as salt, with premixed pyrrolidinium bis(trifluoromethyl sulfonyl)imide (PYR) as solvent and 1,3-dioxolane (DOL) as diluent were used to wet both SSE-electrode interfaces. The effect of IL dilution, co-solvent amount, LiTFSI concentration, C rate at which the batteries are tested and the effect of SSE inside the cathode, were systematically studied and optimized to develop a quasi-solid-state electrolyte Li-S battery (QSSLSB) with higher capacity retention and cyclability. LiTFSI (2M) dissolved in PYR:DOL(1:1) found to be optimum IL combination for low sulfur loading QSSLSBs reaching 500 mAh/g after 100 cycles while LiTFSI (3M) in PYR:DOL(1:3) was the optimum IL concentration for higher loading QSSLSBs reaching 400 mAh/g after 100 cycles. This work reports promising results of QSSLSB based on novel Li6PS5F0.5Cl0.5 Li-argyrodite solid-state electrolyte (SSE) with minute amount of IL, Super P-Sulfur (SP:S) cathode, and Li-anode. It also offers a new insight into the intimate interfacial contacts between the SSE and carbon-sulfur cathodes, which will be critical for improved electrochemical performance of quasi-solid-state lithium-sulfur batteries with high sulfur loading in the future.

25 ENERGY STORAGE↗
DOE OSTI2020

Highly-Cyclable Room-Temperature Phosphorene Polymer Electrolyte Composites for Li Metal Batteries

Despite significant interest toward solid-state electrolytes owing to their superior safety in comparison to liquid-based electrolytes, sluggish ion diffusion and high interfacial resistance limit their application in durable and high-power density batteries. Here, a novel quasi-solid Li + ion conductive nanocomposite polymer electrolyte containing black phosphorous (BP) nanosheets is reported. The developed electrolyte is successfully cycled against Li metal (over 550 h cycling) at 1 mA cm -2 at room temperature. The cycling overpotential is dropped by 75% in comparison to BP-free polymer composite electrolyte indicating lower interfacial resistance at the electrode/electrolyte interfaces. Molecular dynamics simulations reveal that the coordination number of Li + ions around (trifluoromethanesulfonyl)imide (TFSI - ) pairs and ethylene-oxide chains decreases at the Li metal/electrolyte interface, which facilitates the Li + transport through the polymer host. Here, density functional theory calculations confirm that the adsorption of the LiTFSI molecules at the BP surface leads to the weakening of N and Li atomic bonding and enhances the dissociation of Li + ions. This work offers a new potential mechanism to tune the bulk and interfacial ionic conductivity of solid-state electrolytes that may lead to a new generation of lithium polymer batteries with high ionic conduction kinetics and stable long-life cycling.

2D materials↗
DOE OSTI2021

Engineering the Interlayer Spacing by Pre-Intercalation for High Performance Supercapacitor MXene Electrodes in Room Temperature Ionic Liquid

MXenes exhibit excellent capacitance at high scan rates in sulfuric acid aqueous electrolytes, but the narrow potential window of aqueous electrolytes limits the energy density. Organic electrolytes and room-temperature ionic liquids (RTILs) can provide higher potential windows, leading to higher energy density. The large cation size of RTIL hinders its intercalation in-between the layers of MXene limiting the specific capacitance in comparison to aqueous electrolytes. In this work, different chain lengths alkylammonium (AA) cations are intercalated into Ti 3 C 2 T x , producing variation of MXene interlayer spacings (d-spacing). AA-cation-intercalated Ti 3 C 2 T x (AA-Ti 3 C 2 ), exhibits higher specific capacitances, and cycling stabilities than pristine Ti 3 C 2 T x in 1 m 1-ethly-3-methylimidazolium bis-(trifluoromethylsulfonyl)-imide (EMIMTFSI) in acetonitrile and neat EMIMTFSI RTIL electrolytes. Pre-intercalated MXene with an interlayer spacing of ≈2.2 nm, can deliver a large specific capacitance of 257 F g –1 (1428 mF cm –2 and 492 F cm –3 ) in neat EMIMTFSI electrolyte leading to high energy density. Quasi elastic neutron scattering and electrochemical impedance spectroscopy are used to study the dynamics of confined RTIL in pre-intercalated MXene. Furthermore, molecular dynamics simulations suggest significant differences in the structures of RTIL ions and AA cations inside the Ti 3 C 2 T x interlayer, providing insights into the differences in the observed electrochemical behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ionic Dopant-Induced Ordering Enhances the Thermoelectric Properties of a Polythiophene-Based Block Copolymer

Conjugated polymer-based block copolymers (CP-BCPs) are an unexplored class of materials for organic thermoelectrics. In this study, the authors report on the electronic conductivity (σ) and Seebeck coefficient (α) of a newly synthesized CP-BCP, poly(3-hexylthiophene)-block-poly (oligo-oxyethylene methacrylate) (P3HT-b-POEM), upon solution co-processing with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), and subsequently vapor-doping with a molecular dopant, 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ). It is found that the addition of the hydrophilic block POEM greatly enhances the processability of P3HT, enabling homogeneous solution-mixing with LiTFSI. Notably, interactions between P3HT-b-POEM with ionic species significantly improve molecular order and unexpectedly cause electrical oxidizing doping of P3HT block both in solution and solid-states, a phenomenon that has not been previously observed in Li-salt containing P3HT. Vapor doping of P3HT-b-POEM-LiTFSI thin films with F4TCNQ further enhances σ and yields a thermoelectric power factor PF = α 2 σ of 13.0 μW m -1 K -2 , which is more than 20 times higher than salt-free P3HT-b-POEM sample. Through modeling thermoelectric behaviors of P3HT-b-POEM with the Kang-Snyder transport model, the improvement in PF is attributed to higher electronic charge mobility originating from the enhanced molecular ordering of P3HT. The results demonstrate that solution co-processing CP-BCPs with a salt is a powerful method to control structure and performance of organic thermoelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhancing Cycling Stability of Lithium Metal Batteries by a Bifunctional Fluorinated Ether

Abstract The lifespan of lithium (Li) metal batteries (LMBs) can be greatly improved by the formation of inorganic‐rich electrode‐electrolyte interphases (EEIs) (including solid‐electrolyte interphase on anode and cathode‐electrolyte interphase on cathode). In this work, a localized high‐concentration electrolyte containing lithium bis(fluorosulfonyl)imide (LiFSI) salt, 1,2‐dimethoxyethane (DME) solvent and 1,2‐bis(1,1,2,2‐tetrafluoroethoxy)ethane (BTFEE) diluent is optimized. BTFEE is a fluorinated ether with weakly‐solvating ability for LiFSI so it also acts as a co‐solvent in this electrolyte. It can facilitate anion decomposition at electrode surfaces and promote the formation of more inorganic‐rich EEI layers. With an optimized molar ratio of LiFSI:DME:BTFEE = 1:1.15:3, LMBs with a high loading (4 mAh cm −2 ) lithium nickel manganese cobalt oxide (LiNi 0.8 Mn 0.1 Co 0.1 ) cathode can retain 80% capacity in 470 cycles when cycled in a voltage range of 2.8–4.4 V. The fundamental understanding on the functionality of BTFEE revealed in this work provides new perspectives on the design of practical high‐energy density battery systems.

25 ENERGY STORAGE↗
DOE OSTI2025

Enhanced Ion Transport and Molecular Packing Stability in Asymmetric 2D Nanostructured π‐Conjugated Thieno[3,2‐b]Thiophene‐Based Liquid Crystal

Organic semiconductors based on liquid crystal (LC) molecules have attracted increasing interest. Here, in this work, two linear LCs based on 2,5‐bis(thien‐2‐yl)thieno[3,2‐b]thiophene (BTTT) mesogen are designed and synthesized, including BTTT/dEO3 with two symmetrically attached tri(ethylene oxide) groups and BTTT/mEO6 with one asymmetrically attached hexa(ethylene oxide) group. These two molecules have comparable functional‐group compositions but different molecular geometries, leading to their moderately different material performances. Both LCs show smectic mesophases with relatively low transition temperatures as confirmed by differential scanning calorimetry and polarized optical microscopy. A combination of experimental grazing incidence wide‐angle X‐ray scattering and molecular dynamics (MD) simulations reveals a herringbone packing motif of BTTT segments in both LCs while a smaller molecular tilt angle in BTTT/mEO6. Ionic conductivities are measured by doping LCs with different amounts of ionic dopants, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). BTTT/mEO6 shows better smectic phase stability to higher LiTFSI doping ratios. Both LCs exhibit similar ionic conductivities in the smectic phases, but BTTT/mEO6 outperforms BTTT/dEO3 by a factor of three in the amorphous phase at higher temperatures. MD simulations, performed to examine the ion solvation environment, reveal that BTTT/mEO6 is more efficient in coordinating Li‐ions and screening their interactions with TFSI‐ions which further promote ionic transport.

grazing incidence wide-angle X-ray scattering↗
DOE OSTI2020

Stable Potassium Metal Anodes with an All-Aluminum Current Collector through Improved Electrolyte Wetting

This is the first report of successful potassium metal battery anode cycling with an aluminum-based rather than copper-based current collector. Dendrite-free plating/stripping is achieved through improved electrolyte wetting, employing an aluminum-powder-coated aluminum foil “Al@Al,” without any modification of the support surface chemistry or electrolyte additives. The reservoir-free Al@Al half-cell is stable at 1000 cycles (1950 h) at 0.5 mA cm -2 , with 98.9% cycling Coulombic efficiency and 0.085 V overpotential. The pre-potassiated cell is stable through a wide current range, including 130 cycles (2600 min) at 3.0 mA cm -2 , with 0.178 V overpotential. Al@Al is fully wetted by a 4 m potassium bis(fluorosulfonyl)imide-dimethoxyethane electrolyte (θCA = 0°), producing a uniform solid electrolyte interphase (SEI) during the initial galvanostatic formation cycles. On planar aluminum foil with a nearly identical surface oxide, the electrolyte wets poorly (θCA = 52°). This correlates with coarse irregular SEI clumps at formation, 3D potassium islands with further SEI coarsening during plating/stripping, possibly dead potassium metal on stripped surfaces, and rapid failure. The electrochemical stability of Al@Al versus planar Al is not related to differences in potassiophilicity (nearly identical) as obtained from thermal wetting experiments. Additionally, planar Cu foils are also poorly electrolyte-wetted and become dendritic. The key fundamental takeaway is that the incomplete electrolyte wetting of collectors results in early onset of SEI instability and dendrites.

25 ENERGY STORAGE↗
DOE OSTI2021

Dual-Solvent Li-Ion Solvation Enables High-Performance Li-Metal Batteries

Novel electrolyte designs to further enhance the lithium (Li) metal battery cyclability are highly desirable. Here, fluorinated 1,6-dimethoxyhexane (FDMH) is designed and synthesized as the solvent molecule to promote electrolyte stability with its prolonged –CF 2 – backbone. Meanwhile, 1,2-dimethoxyethane is used as a co-solvent to enable higher ionic conductivity and much reduced interfacial resistance. Combining the dual-solvent system with 1 m lithium bis(fluorosulfonyl)imide (LiFSI), high Li-metal Coulombic efficiency (99.5%) and oxidative stability (6 V) are achieved. Using this electrolyte, 20 µm Li||NMC batteries are able to retain ≈80% capacity after 250 cycles and Cu||NMC anode-free pouch cells last 120 cycles with 75% capacity retention under ≈2.1 µL mAh -1 lean electrolyte conditions. Such high performances are attributed to the anion-derived solid-electrolyte interphase, originating from the coordination of Li-ions to the highly stable FDMH and multiple anions in their solvation environments. This work demonstrates a new electrolyte design strategy that enables high-performance Li-metal batteries with multisolvent Li-ion solvation with rationally optimized molecular structure and ratio.

25 ENERGY STORAGE↗
DOE OSTI2024

4.6 V Moisture‐Tolerant Electrolytes for Lithium‐Ion Batteries

Abstract Commercial LiPF 6 ‐based electrolytes face limitations in oxidation stability (4.2 V) and water tolerance (10 ppm). While replacing LiPF 6 with lithium bis(trifluoromethane)sulfonimide (LiTFSI) improves water tolerance, it induces Al current collector corrosion above 3.7 V vs. Li/Li + . To address this, lithium cyano(trifluoromethanesulfonyl)imide (LiCTFSI) is proposed here as a non‐corrosive, moisture‐tolerant alternative. The 2.0 M LiCTFSI/propylene carbonate (PC)‐fluoroethylene carbonate (FEC) (7:3 by volume) electrolyte enables LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) cathodes to reach 210 mAh g −1 (2.8‐4.6 V) with a cycle life of 500. Full cells with NCM811||graphite (2.0 mAh cm −2 ) show 77.8% capacity retention after 500 cycles. Even with 2000 ppm moisture in the electrolyte, full cells maintain high cycling stability, reducing the need for costly dry rooms. The electrolyte’s low freezing point and high thermal stability enable the operation from ‐20 °C to 60 °C, delivering 168 mAh g −1 at ‐20 °C and retaining 94% capacity after 100 cycles at 60 °C. In contrast, cells with commercial LiPF 6 electrolyte deliver 71 mAh g −1 at ‐20°C and retain 52.7% after 100 cycles at 60 °C. This novel salt offers a cost‐effective solution for developing robust, high‐performance batteries suitable for extreme conditions.

Zhang, Nan↗
DOE OSTI2023

A Nanoscale Ternary Amide‐rGO Composite with Boosted Kinetics for Reversible H 2 Storage

Abstract Metal amides are attractive candidates for hydrogen storage due to their high volumetric and gravimetric hydrogen densities. However, the sluggish kinetics and competing side reactions during hydrogen uptake and release limit their practical use. Here, a novel nanoconfined Li 2 Mg(NH) 2 @reduced graphene oxide (rGO) composite is presented, which is fabricated using a melt‐infiltration method with a minimum weight penalty of only 2 wt.%. The presence of rGO ensures close contact between the active phases, effectively preventing aggregation during cycling process. As a result, the reversible capacity of Li 2 Mg(NH) 2 @rGO reaches 4.42 wt.%, with no capacity degradation observed after multiple cycling. Theoretical calculations show that rGO catalyzes the hydrogen bond cleavage at the Mg‐amide/Li hydride interface, leading to local dehydrogenation hotspots and significantly improves kinetics of dehydrogenation compared to the bulk counterpart. This study provides a promising strategy for designing metal imide‐based composites to overcome the kinetic limitations and improve their reversible hydrogen storage performance.

08 HYDROGEN↗
DOE OSTI2022

Correlation between Redox Potential and Solvation Structure in Biphasic Electrolytes for Li Metal Batteries

The activity of lithium ions in electrolytes depends on their solvation structures. However, the understanding of changes in Li + activity is still elusive in terms of interactions between lithium ions and solvent molecules. Herein, the chelating effect of lithium ion by forming [Li(15C5)] + gives rise to a decrease in Li + activity, leading to the negative potential shift of Li metal anode. Moreover, weakly solvating lithium ions in ionic liquids, such as [Li(TFSI) 2 ] - (TFSI = bis(trifluoromethanesulfonyl)imide), increase in Li + activity, resulting in the positive potential shift of LiFePO 4 cathode. This allows the development of innovative high energy density Li metal batteries, such as 3.8 V class Li | LiFePO 4 cells, along with introducing stable biphasic electrolytes. In addition, correlation between Li + activity, cell potential shift, and Li + solvation structure is investigated by comparing solvated Li + ions with carbonate solvents, chelated Li + ions with cyclic and linear ethers, and weakly solvating Li + ions in ionic liquids. These findings elucidate a broader understanding of the complex origin of Li + activity and provide an opportunity to achieve high energy density lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Flux Synthesis of A-site Disordered Perovskite La 0.5 M 0.5 TiO 3 (M$=$Li, Na, K) Nanorods Tailored for Solid Composite Electrolytes

Inorganic fillers play an important role in improving the ionic conductivity of solid composite electrolytes (SCEs) for Li-ion batteries. Among inorganic fillers, perovskite-type lithium lanthanum titanate (LLTO) stands out for its high bulk Li + conductivity on the order of 10 -3 S cm -1 at room temperature. According to a literature survey, the optimal LLTO filler should possess the following characteristics: i) a single-crystal structure to minimize grain boundaries; ii) a small particle size to increase the filler/polymer interface area; iii) a 1D morphology for efficient interface channels; and iv) cubic symmetry to facilitate rapid bulk Li + diffusion within the filler. However, the synthesis of single crystal, 1D LLTO nanomaterials with cubic symmetry is challenging. Herein, a flux strategy is developed to synthesize La 0.5 M 0.5 TiO 3 (LMTO, M$=$Li, Na, and K) single-crystal nanorods with an A-site-disordered, cubic perovskite phase. The flux media promotes the oriented growth of nanorods, prevents nanorods from sintering, and provides multiple alkali metal ion doping at M sites to stabilize the cubic phase. SCEs compositing the Li + -conducting LMTO nanorods as fillers and poly[vinylene carbonate- co -lithium sulfonyl(trifluoromethane sulfonyl)imide methacrylate] matrix exhibit more than twice the conductivity of the neat polymer electrolyte (30.6 vs 14.0 µS cm -1 at 303 K).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Scalable, Ultrathin, and High-Temperature-Resistant Solid Polymer Electrolytes for Energy-Dense Lithium Metal Batteries

We report all-solid-state batteries (ASSBs) demonstrate great promise, offering high energy density, good thermal stability, and safe operation compared with traditional Li-ion batteries. Among various solid-state electrolytes (SSEs), solid polymer electrolytes (SPEs) offer an attractive choice due to their thinness, low density, and good manufacturability. However, ultrathin SPEs that work with practical current densities or at high temperatures remain challenging, limiting applicable conditions of SPE-based batteries. Here, the authors report a novel scalable, ultrathin, and high-temperature-resistant SPE for ASSBs. This design includes an electrospun polyacrylonitrile (PAN) matrix and polyethylene oxide (PEO)/Li salt ionic conductor, which offers a stable LiF and Li 3 N containing SSE/Li interface. The unique interface—as well as the good mechanical strength—inhibits lithium dendrites and prevents short circuiting. As a result, symmetrical Li-Li cells deliver more than 300 h cyclability at 0.5 mA cm -2 . ASSBs fabricated with only 5 µm-thickness PAN-PEO/lithium bis(trifluoromethanesulfonyl)imide reach 300 cycles at 0.3 C rate at 60 °C. The excellent thermal stability of PAN also results in safer SPEs at high temperatures. The design extends battery operation up to temperatures of 120 and 150 °C, where it achieves 500 cycles at C/2 rate and 100 cycles at 2C rate, respectively.

25 ENERGY STORAGE↗
DOE OSTI2022

A Dual–Phase Electrolyte for High–Energy Lithium–Sulfur Batteries

Dissolution of lithium polysulfides (LiPSs) is essential for fast cathode kinetics, but detrimental for anode stability, especially under lean electrolyte conditions. Here in this work, the phase separation phenomenon between solvents with different polarities (tetramethyl sulfone [TMS] and dibutyl ether [DBE]) is utilized to enable the design of a dual-phase electrolyte. High-polarity, high-density TMS–lithium bis(trifluoromethanesulfonyl)imide–ammonium trifluoroacetate as the cathode electrolyte strongly solvates LiPSs, which propel the sulfur redox reaction. Moreover, the composite of DBE and a polymeric ion conductor serves as the anode electrolyte. The addition of DBE in the anode side effectively prevents the crossover of corrosive species (LiPSs and ammonia trifluoroacetate), enabling a significant improvement in Li-metal anode stability. The electrode-specific dual-phase electrolyte design provides electrochemical performance superior to conventional electrolytes. Without additional electrode engineering, pouch cells assemble with the dual-phase electrolyte cycle under a lean electrolyte (4 µL mg –1 ) and low-Li-excess condition (N/P = 3) for 120 cycles.

25 ENERGY STORAGE↗
DOE OSTI2021

Synthesis, Electronic Structure, and Reactivity of a Planar Four‐Coordinate, Cobalt–Imido Complex

Abstract A four‐coordinate cobalt–imido complex, ( t Bu mPNP)Co=NMes ( t Bu mPNP=modified PNP pincer ligand) has been synthesized from addition of 2,4,6‐trimethylphenylazide (Mes–N 3 ) to the corresponding dinitrogen complex. The solid‐state structure determined by X‐ray diffraction established a rare, idealized planar geometry with a Co=N bond distance of 1.716(2) Å. Magnetic measurements revealed an S =1 ground state with CAS‐SCF calculations supporting radical character on the imide nitrogen. Thermolysis of the cobalt–imido compound induced selective insertion of the imido group into a Co−P bond and yielded a three‐coordinate cobalt complex with a distorted T‐shaped geometry. Transition state analysis conducted with DFT calculations established the thermodynamic stability of the P–N coupled product and provided insight into the exclusive selectivity.

Park, Yoonsu↗
DOE OSTI2022

Semiconducting Copolymers with Naphthalene Imide/Amide π‐Conjugated Units: Synthesis, Crystallography, and Systematic Structure‐Property‐Mobility Correlations

Abstract In a series of n‐type semiconducting naphthalene tetracarboxydiimide ( NDI )‐dithiophene ( T2 ) copolymers, structural and electronic properties trends are systematically evaluated as the number of NDI carbonyl groups is reduced from 4 in NDI to 3 in NBL (1‐amino‐4,5‐8‐naphthalene‐tricarboxylic acid‐1,8‐lactam‐4,5‐imide) to 2 in NBA (naphthalene‐bis(4,8‐diamino‐1,5‐dicarboxyl)‐amide). As the NDI ‐ T2 backbone torsional angle falls the LUMO energy rises. However, the thienyl attachment regiochemistry also plays an important role in less symmetric NBL and NBA . Electron mobility is greatest for N2200 (0.17 cm 2 V −1 s −1 ) followed by PNBL‐3,8‐T2 and PNBA‐2,6‐T2 (0.11 cm 2 V −1 s −1 ), 0.02 cm 2 V −1 s −1 in PNBL‐4,8‐T2 , and negligible in PNBA‐3,7‐T2 . Charge transport reflects a delicate balance between electronic backbone communication (optimum for N2200 and PNBL‐4,8‐T2 ), backbone planarity (optimum for PNBA‐2,6‐T2 and PNBL‐3,8‐T2 ), LUMO energy (optimum for N2200 ), π–π stacking distance (optimum for PNBA‐2,6‐T2 ), and film crystallinity (optimum for PNBA‐2,6‐T2 and N2200 ). These results offer generalizable insight into semiconducting copolymer design.

Chen, Yao↗
DOE OSTI2021

Synthesis, Electronic Structure, and Reactivity of a Planar Four–Coordinate, Cobalt–Imido Complex

A four-coordinate cobalt imido complex, ( tBu mPNP)Co=NMes ( tBu mPNP = modified PNP pincer ligand) has been synthesized from addition of 2,4,6-trimethylphenylazide (Mes–N 3 ) to the corresponding dinitrogen complex. The solid-state structure determined by X-ray diffraction established a rare, idealized planar geometry with a Co=N bond distance of 1.716(2) Å. Magnetic measurements revealed an S = 1 ground state with CAS-SCF calculations supporting radical character on the imide nitrogen. Here, thermolysis of the cobalt-imido compound induced selective insertion of the imido group into a Co–P bond and yielded a three-coordinate cobalt complex with a distorted T-shaped geometry. Transition state analysis conducted with DFT calculations established the thermodynamic stability of the P–N coupled product and provided insight into the exclusive selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Semiconducting Copolymers with Naphthalene Imide/Amide π-Conjugated Units: Synthesis, Crystallography, and Systematic Structure-Property-Mobility Correlations

Here, in a series of n-type semiconducting naphthalene tetracarboxydiimide (NDI)-dithiophene (T2) copolymers, structural and electronic properties trends are systematically evaluated as the number of NDI carbonyl groups is reduced from 4 in NDI to 3 in NBL (1-amino-4,5-8-naphthalene-tricarboxylic acid-1,8-lactam-4,5-imide) to 2 in NBA (naphthalene-bis(4,8-diamino-1,5-dicarboxyl)-amide). As the NDI-T2 backbone torsional angle falls the LUMO energy rises. However, the thienyl attachment regiochemistry also plays an important role in less symmetric NBL and NBA. Electron mobility is greatest for N2200 (0.17 cm 2 V –1 s –1 ) followed by PNBL-3,8-T2 and PNBA-2,6-T2 (0.11 cm 2 V –1 s –1 ), 0.02 cm 2 V –1 s –1 in PNBL-4,8-T2, and negligible in PNBA-3,7-T2. Charge transport reflects a delicate balance between electronic backbone communication (optimum for N2200 and PNBL-4,8-T2), backbone planarity (optimum for PNBA-2,6-T2 and PNBL-3,8-T2), LUMO energy (optimum for N2200), π–π stacking distance (optimum for PNBA-2,6-T2), and film crystallinity (optimum for PNBA-2,6-T2 and N2200). These results offer generalizable insight into semiconducting copolymer design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗