SEARCH · Search NASA

Results for “INTERNAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Mechanics of failure of composite materials

Composite materials are both inhomogeneous and anisotropic. Both of these characteristics affect the internal stress distributions since inhomogeneity involves variations in both strength and stiffness. The fracture mechanics of nonuniform materials are considered, taking into account the effect of nonuniformity on stress distributions near the crack tip, predicted yield zones in nonuniform and uniform materials, and the fracture of a center-notched unidirectional specimen. The mechanics of failure of laminated materials is discussed. It is found that the development of damage in a laminate with increasing load and, possibly, increasing numbers of cycles of loading is peculiar to the laminate in question, i.e., the material system, the stacking sequence, and the geometry. Approaches for monitoring damage development are also described.

Reifsnider, K. L.↗

NASA NTRS1978

Coatings for wear and lubrication

In this paper we review the recent advances in the tribological uses of R.F.-sputtered and ion-plated films of solid film lubricants (laminar solids, soft metals, organic polymers) and wear-resistant refractory compounds (carbides, nitrides, silicides). The sputtering and ion-plating potentials and the corresponding coatings formed are evaluated relative to the friction coefficient, wear endurance life and mechanical properties. The tribological and mechanical properties of each kind of film are discussed in terms of film adherence, coherence, density, grain size, morphology, internal stresses and thickness and substrate conditions such as temperature, topography, chemistry and d.c. biasing. The ion-plated metallic films in addition to improved tribological properties also have better mechanical properties such as tensile strength and fatigue life.

Spalvins, T.↗

NASA NTRS1982

Plasma deposition and surface modification techniques for wear resistance

The ion-assisted or plasma coating technology is discussed as it applies to the deposition of hard, wear resistant refractory compound films. Of the many sputtering and ion plating modes and configurations the reactive magnetron sputtering and the reactive triode ion plating techniques are the preferred ones to deposit wear resistant coatings for tribological applications. Both of these techniques incorporate additional means to enhance the ionization efficiency and chemical reaction to precision tailor desirable tribological characteristics. Interrelationships between film formation, structure, and ribological properties are strictly controlled by the deposition parameters and the substrate condition. The enhanced ionization contributes to the excellent adherence and coherence, reduced internal stresses and improved structural growth to form dense, cohesive, equiaxed grain structure for improved wear resistance and control.

Spalvins, T.↗

NASA NTRS1982

A new capability for elastic aircraft airloads via NASTRAN

A new direct matrix abstract program for NASTRAN written to calculate internal stresses and airloads for a flexible wing is described. The difficulties encountered in interfacing the doublet lattice solution to the aerodynamic problem to the finite element solution to the structural problem are discussed. A brief numerical example is included.

Briggs, H. C.↗

NASA NTRS1985

Interferometer Detects Acoustic Emissions in Composites

Embedded single-mode optical fibers sample internal-stress fields directly. Statically loaded composite matrix emits pulsed ultrasonic waves which mechanically modulate embedded fiber and phase-modulate transmitted optical field. Modulation detected by optical interferometry and Fourier optical processing converted to electronic signal proportional to acoustic field amplitude integated along length of fiber embedded in specimen. Technique used for measurements of both high- and low-frequency CW acoustic fields as well as high-frequency transients.

Cantrell, J. H.↗

NASA NTRS1984

Status of Plasma Physics Techniques for the Deposition of Tribological Coatings

This paper reviews the plasma physics deposition techniques of sputtering and ion-plating. Their characteristics and potentials are discussed in terms of synthesis or deposition of tribological coatings. Since the glow discharge or plasma generated in the conventional sputtering and ion-plating techniques has a low ionization efficiency (<0.1%), rapid advances have been made in equipment design to further increase the ionization efficiency. The enhanced ionization favorably affects the nucleation and growth sequence of the coating. This leads to improved adherence and coherence, higher density, favorable morphological growth, and reduced internal stresses in the coatings. As a result, desirable coating characteristics can be precision tailored. Tribological coating characteristics of sputtered solid film lubricants such as MoS2, ion-plated soft gold and lead metallic films, and sputtered and ion-plated wear-resistant refractory compound films such as nitrides and carbides are discussed.

Talivaldis Spalvins↗

NASA NTRS1985

Fault Offsets and Lateral Crustal Movement on Europa

Structural evidence is presented for tension cracking associated with strike slip faulting and crustal movement in the bright ice covered Galilean satellite Europa. The structure and morphology of wedge shaped bands argues that they formed as a result of the rotation and lateral displacement of crustal units bounded by near vertical faults penetrating through the brittle crustal layer. The significant rotation and lateral motion of crustal blocks near the anti-jove point on Europa, without graben formation, also argues that the lithosphere in the fractured area is mechanically decoupled from the solid silicate interior, by either warm ice at depth or liquid water. Ice at depth and at a large fraction of its melting temperature is expected to behave as a fluid over geologically short time intervals due to its extremely low viscosity relative to the cold, brittle ice near the surface. One proposed convection mechanism is thus considered unlikely as it would be difficult to transmit internal stress through a decoupling layer to the surface.

Schenk, P. M.↗

NASA NTRS1985

The structure of ion plated films in relation to coating properties

Ion plating is an ion assisted or glow discharge deposition technique, where ions or energetic atoms transfer energy, momentum and charge to the substrate and the growing film in a manner which can be controlled to favorably modify surface, subsurface chemistry, and microstructure. The glow discharge energizing effects from the initial nucleation stages to the final film growth are discussed. As a result, adherence, coherence, internal stresses, density and morphology of the coatings are significantly improved, over the conventional (nonion-assisted) techniques which in turn favorably affect the surface initiated failures caused by friction, wear, erosion, corrosion and fatigue. Ion plated films because of their graded coating/substrate interface, fine, uniform, densely packed film structure also induce a surface strengthening effect which improved the mechanical properties such as yield, tensile strength and fatigue life. Since a uniform, continuous film can be obtained at lower nominal film thickness, this effect is of great importance in solid film lubrication and in corrosion protection.

Spalvins, T.↗

NASA NTRS1984

Fracture behavior in silicon

The fracture mechanics of crystalline Si are reviewed, together with known techniques for minimizing the occurences of fracture and/or their effects. The fracture toughness (Kic) of Si varies only 10 percent from cell-to-cell and standard values have been established for different types of crystalline Si cells. A critical flaw size of 10-100 microns has been identified, and also pertains to polycrystalline materials. Chemical polishing is known to double the value of Kic, while edge rounding has no effect. Internal stresses, particularly those caused during ribbon growth, do not exceed 10 percent of Kic. External stresses are imposed by the module hardware and the ambient environment. Multiple contacts reduce the effects of cell fracture and series-parallel wiring in modules in arrays ameliorates the effects of single-cell failures. During manufacturing, maintenance of quality control and removal of sheets displaying aberrations can, depending on the costs and the implementation of the array reliability features, result in arrays delivering any desired level of reliability.

Leipold, M. H.↗

NASA NTRS1986

Effect of annealing history on free volume in thermoplastics

Two different types of thermoplastic glassy polymers have been investigated for the effects of thermal annealing on their free volumes. It has been observed that free volumes in glassy polymers decrease asymptotically to a steady level after about four thermal anneals lasting for 24 hours at a temperature about 50 C below their glass transition temperatures. These results indicate that composites incorporating properly annealed thermoplastic matrices may not experience any additional internal stresses due to subsequent thermal excursions experienced while in service.

Singh, J. J.↗

NASA NTRS1986

Ice banding as a response of the coupled ice-ocean system to temporally varying winds

This study models formation of ice bands in the marginal ice zones. A one-dimensional coupled ice-ocean model is used in which the ice model is coupled to a reduced gravity ocean model through interfacial stresses. The internal ice stresses are important only at high ice concentrations (90-100 percent); otherwise, the main balance for the ice motion is between the air-ice stress and the ice-water stress, i.e., free drift. The drag coefficients were chosen so that the air-ice momentum flux is 3 times greater than the air-ocean momentum flux. Thus the Ekman transport is larger under the ice than in the open water, so that winds parallel to the ice edge, with the ice on the right, produce upwelling. The upwelling simulation was extended to include temporally varying forcing, which was chosen to vary sinusoidally with a 4-day period. This forcing resembles successive cyclone passings perpendicular to the ice edge. When the oceanic upper layer was thin, which means that the dynamics are strongly nonlinear, the ice bands were formed. The up/downwelling signals do not disappear in wind reversals because of nonlinear advection. This leads to convergences and divergences in oceanic and ice velocities that manifest themselves as ice banding. At least one wind reversal is needed to produce one ice band.

Hakkinen, S.↗

NASA NTRS1987

A preliminary study of factors affecting the calibration stability of the iridium versus iridium-40 percent rhodium thermocouple

An iridium versus iridium-40% rhodium thermocouple was studied. Problems associated with the use of this thermocouple for high temperature applications (up to 2000 C) were investigated. The metallurgical studies included X-ray, macroscopic, resistance, and metallographic studies. The thermocouples in the as-received condition from the manufacturer revealed large amounts of internal stress caused by cold working during manufacturing. The thermocouples also contained a large amount of inhomogeneities and segregations. No phase transformations were observed in the alloy up to 1100 C. It was found that annealing the thermocouple at 1800 C for two hours, and then at 1400 C for 2 to 3 hours yielded a fine grain structure, relieving some of the strains, and making the wire more ductile. It was also found that the above annealing procedure stabilized the thermal emf behavior of the thermocouple for application below 1800 C (an improvement from + or - 1% to + or - 0.02% within the range of the test parameters used).

Ahmed, Shaffiq↗

NASA NTRS1987

Ion plated gold films: Properties, tribological behavior and performance

The glow discharge energizing favorably modifies and controls the coating/substrate adherence and the nucleation and growth sequence of ion plated gold films. As a result the adherence, coherence, internal stresses, and morphology of the films are significantly improved. Gold ion plated films because of their graded coating/substrate interface and fine uniform densely packed microstructure not only improve the tribological properties but also induce a surface strengthening effect which improves the mechanical properties such as yield, tensile, and fatigue strength. Consequently significant improvements in the tribological performance of ion plated gold films as compared to vapor deposited gold films are shown in terms of decreased friction/wear and prolonged endurance life.

Spalvins, Talivaldis↗

NASA NTRS1988

X-Ray-Scattering Measurements Of Strain In PEEK

Internal stress relieved by heating above glass-transition temperature. Report describes wide-angle x-ray scattering and differential scanning calorimetry of specimens of poly(etheretherketone) having undergone various thermal treatments. Wide-angle x-ray scattering particularly useful in determining distances between atoms, crystallinity, and related microstructurally generated phenomena, as thermal expansion and strain. Calorimetric measurements aid interpretation of scattering measurements by enabling correlation with thermal effects.

Cebe, Peggy↗

NASA NTRS1988

Simulated impact damage in a thick graphite/epoxy laminate using spherical indenters

A study was made to determine the extent of fiber damage caused by low-velocity impact of spherical impactors to a very thick graphite/epoxy laminate. The laminate was cut from a filament wound case being developed for the Space Shuttle solid rocket motors. The case was wound using a wet process with AS4W graphite fiber and HBRF-55A epoxy. Impacts were simulated under quasi-static conditions by pressing hemispherically shaped indenters against the laminate at different locations. The contact force and indenter diameter were varied from location to location. The forces were chosen for each indenter diameter to produce contact pressures below and above that required to initiate damage. After the forces were applied, the laminate was cut into smaller pieces so that each piece contained a test site. The pieces were then deplied and the individual plies examined to determine the extent of fiber damage. Broken fibers were found in the outer layers directly beneath the contact site. The locus of broken fibers in each layer resembled a crack normal to the direction of the fibers. The maximum length and depth of the cracks increased with increasing contact pressure and indenter diameter. The internal stresses in the laminate were calculated using Hertz's law and Love's solution for pressure applied on part of the boundary of a semi-infinite body. The maximum length and depth of the cracks were predicted using a maximum shear stress criterion. Predictions and measurements were in good agreement.

Poe, C. C., Jr.↗

NASA NTRS1988

Time-domain transient elastodynamic analysis of 3-D solids by BEM

The BEM algorithm developed by Banerjee and Ahmad (1985) and Banerjee et al. (1986) for the analysis of three-dimensional time-dependent elastodynamics problems is extended and refined to improve the accuracy of the internal stress predictions. A quadratic spatial shape function and a linear temporal shape function are employed, and the complete numerical implementation (as part of BEST3D) is outlined. Applications of the improved BEM to typical problems are presented graphically and briefly characterized. Included are spherical cavities subjected to sudden radial expansion, triangular or rectangular pulses of radial pressure, or ramp loading; a circular loaded area on a half space; and a flexible square plate foundation on an elastic half space.

Ahmad, S.↗

NASA NTRS1989

Annealing Increases Stability Of Iridium Thermocouples

Metallurgical studies carried out on samples of iridium versus iridium/40-percent rhodium thermocouples in condition received from manufacturer. Metallurgical studies included x-ray, macroscopic, resistance, and metallographic studies. Revealed large amount of internal stress caused by cold-working during manufacturing, and large number of segregations and inhomogeneities. Samples annealed in furnace at temperatures from 1,000 to 2,000 degree C for intervals up to 1 h to study effects of heat treatment. Wire annealed by this procedure found to be ductile.

Germain, Edward F.↗

NASA NTRS1989

Toughness distribution considerations in a thin film system

The spontaneous mechanical failure of thin films and occasionally substrates, due to the thin film deposition, are relatively common occurrences. Large internal stresses (e.g. 10 MPa to 100 MPa) are an inherent part of the thin film deposition process. In most cases where fracture mechanics has been applied to thin film systems, the failure path is confined a priori to the substrate-thin film interface or in the thin film perpendicular to that interface. This paper considers the contributions which determine the failure path and presents a qualitative model for identifying the failure path in a thin film system taking into account the presence of residual stresses. The most important aspect of this model is that it offers an explanation of the variation in the locus of failure that does not strictly depend on the weakest point of the material (i.e. the least work of fracture) being the first to fail. It does not, inherent to its construction, restrict failure to the interface a priori. The fracture mechanics criterion of the strain energy release rate equaling the material's resistance to crack growth leads to crack propagation at a specific location and defines the selection of the fracture path.

Brown, L. D.↗