Search NASA⌕ Search

SEARCH · Search NASA

Results for “ISOTHERMAL PROCESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Fractal Nanostructured Solar Selective Surfaces for Next Gen Concentrating Solar Power (Final Report)

This project reports a novel coating with enhanced solar absorptance and reduced thermal emittance with high efficiency at elevated temperature for next-generation concentrated solar power (CSP) plants, with targeted operating temperatures around 750°C. Highly textured single and multimetallic oxide coatings were electrodeposited onto Inconel substrate by systematically varying the composition and process parameters. The optimized coating exhibited micro-to-nano structures designed to match the wavelengths in the visible region of the solar spectrum. These structures facilitate resonant absorption of solar radiation, significantly boosting solar absorption and accommodating thermal stress during high temperature exposure. A high solar absorptance exceeding 0.985 and a low thermal emittance below 0.5, yielding a thermal efficiency near 95%, was achieved for the optimized coatings without any anti-reflective overcoat, that remained robust after 750 h of isothermal exposure to 750°C in air. The coatings are also robust to severe mechanical and environmental stressors. The innovative approach presented in this study demonstrates the potential for tailoring air-stable solar absorber coatings to achieve high absorption, low emittance, and excellent high-temperature endurance, meeting the rigorous demands of next-generation CSP systems. A technoeconomic analysis reveals the economic advantage of the coatings for Gen3 CSP installations in different geographical zones globally.

14 SOLAR ENERGY↗
DOE OSTI2024

Microwave Absorbing Perovskite Catalysts for Efficient Electrification of Syngas Production from CO2 and Methane

Microwave absorbing catalysts have the potential to make thermal reactions such as methane reforming (CH4 + CO2 + H2O → H2 + CO) into carbon negative processes when coupled with decarbonized electricity. Due to microwaves directly heating the catalyst rather than heating the reactor and gases, even high temperature reactions such as dry reforming methane (DRM, CH4 + CO2 → H2 + CO) can be achieved rapidly, efficiently, and on-demand, ideal for coupling with intermittent renewable electricity. However, microwave catalysts present unique design challenges due to the same material needing to both efficiently absorb microwaves in oxidative and reductive reaction conditions and be an efficient and stable catalyst in inherently non-isothermal reactors. We screened from over 28 catalysts in the La0.8Sr0.2(Co-Ni-Mn)O3 perovskite solid-solution family to determine promising microwave reforming catalysts and identify design principles for effective materials. The best performing catalyst candidate was able to produce syngas ratios (H2:CO) from 1-3, and scale up testing showed CO and H2 production efficiencies rivaling conventional carbon intensive steam reforming efficiencies at the liters per minute level of production.

Marin, Christopher↗
DOE OSTI2024

A Portable Miniature Cryogenic Environment for In Situ Neutron Diffraction

Neutron diffraction instruments offer a platform for materials science and engineering studies at extended temperature ranges far from ambient. As one of the widely used neutron sample environment types, cryogenic furnaces are usually bulky and complex, and they may need hours of beamtime overhead for installation, configuration, cooling, and sample change, etc. To reduce the overhead time and expedite experiments at the state-of-the-art high-flux neutron source, we developed a low-cost, miniature, and easy-to-use cryogenic environment (77–473 K) for in situ neutron diffraction. A travel-size mug serves for the environment where the samples sit inside. Immediate cooling and an isothermal dwell at 77 K are realized on the sample by direct contact with liquid N 2 in the mug. The designed Al inserts serve as the holder of samples and heating elements, alleviate the thermal gradient, and clear neutron pathways. Both a single-sample continuous measurement and multi-sample high-throughput measurements are demonstrated in this environment. High-quality and refinable in situ neutron diffraction patterns are acquired on model materials. The results quantify the orthorhombic-to-cubic phase transformation process in LiMn 2 O 4 and differentiate the anisotropic lattice thermal expansions and bond length evolutions between rhombohedral perovskite oxides with composition variation.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Investigating Fast Scanning Calorimetry and Differential Scanning Calorimetry as Screening Tools for Thermoset Polymer Material Compatibility with Laser-Based Powder Bed Fusion

As additive manufacturing (AM) technology has developed and progressed, a constant topic of research in the area is expanding the library of materials to be used with these techniques. Among AM methods that utilize polymers, laser-based powder bed fusion (PBF-LB) has preferentially used thermoplastic polymers as its starting materials, but the deposition and material joining method employed in PBF-LB may also be compatible with powdered thermoset polymer precursors as feedstocks. To assess the compatibility of candidate thermosetting polymers and PBF-LB, characterization techniques and protocols that link fundamental material behavior to material behavior in the processing environment are needed. Therefore, the objectives of this work are to compare the curing behavior measured with two different calorimetry techniques that can operate in different heating rate regimes, differential scanning calorimetry (DSC) and fast scanning calorimetry (FSC), and to assess the capabilities of these techniques to act as materials screening tools for PBF-LB. A commercial polyester powder coating is used as a model material to evaluate the potential of obtaining complimentary information for material screening through a combination of calorimetry methods, and its non-isothermal curing behavior is measured at heating rates between 5 °C/min and 7500 °C/min. Curing exotherms are observed with both calorimetry techniques, and comparing the enthalpy associated with curing shows that incomplete curing occurs at higher heating rates, with relative conversion values of approximately 30%. The curing data are fit with two isoconversional models, Friedman and Starink, which show a reduced activation energy at higher heating rates as well, signifying a lower barrier to curing at the conditions used in the FSC experiments. Overall, the results of this work indicate that using these two calorimetry techniques as tiered screening tools can provide valuable information about how curing may proceed in PBF-LB and inform materials selection and design activities for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A molecular view of peptoid-induced acceleration of calcite growth

The extensive deposits of calcium carbonate (CaCO 3 ) generated by marine organisms constitute the largest and oldest carbon dioxide (CO 2 ) reservoir. These organisms utilize macromolecules like peptides and proteins to facilitate the nucleation and growth of carbonate minerals, serving as an effective method for CO 2 sequestration. However, the precise mechanisms behind this process remain elusive. In this study, we report the use of sequence-defined peptoids, a class of peptidomimetics, to achieve the accelerated calcite step growth kinetics with the molecular level mechanistic understanding. By designing peptoids with hydrophilic and hydrophobic blocks, we systematically investigated the acceleration in step growth rate of calcite crystals using in situ atomic force microscopy (AFM), varying peptoid sequences and concentrations, CaCO 3 supersaturations, and the ratio of Ca 2+ / HCO 3 − . Mechanistic studies using NMR, three-dimensional fast force mapping (3D FFM), and isothermal titration calorimetry (ITC) were conducted to reveal the interactions of peptoids with Ca 2+ and HCO 3 − ions in solution, as well as the effect of peptoids on solvation and energetics of calcite crystal surface. Our results indicate the multiple roles of peptoid in facilitating HCO 3 − deprotonation, Ca 2+ desolvation, and the disruption of interfacial hydration layers of the calcite surface, which collectively contribute to a peptoid-induced acceleration of calcite growth. These findings provide guidelines for future design of sequence-specific biomimetic polymers as crystallization promoters, offering potential applications in environmental remediation (such as CO 2 sequestration), biomedical engineering, and energy storage where fast crystallization is preferred.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A simple model for short-range ordering kinetics in multi-principal element alloys

Short-range ordering (SRO) in multi-principal element alloys influences material properties such as strength and corrosion. While some degree of SRO is expected at equilibrium, predicting the kinetics of its formation is challenging. We present a simplified isothermal concentration-wave (CW) model to estimate an effective relaxation time of SRO formation. Estimates from the CW model agree to within a factor of five with relaxation times obtained from kinetic Monte Carlo (kMC) simulations when above the highest ordering instability temperature. Further, the advantage of the CW model is that it only requires mobility and thermodynamic parameters, which are readily obtained from alloy mobility databases and Metropolis Monte Carlo simulations, respectively. The simple parameterization of the CW model and its analytical nature makes it an attractive tool for the design of processing conditions to promote or suppress SRO in multicomponent alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Surface smoothing for laser powder-bed Ti-6Al-4V by a transient liquid phase

Surface roughness is the primary driver of fatigue for additively manufactured metals. To address surface roughness, this work introduces a new method to smooth features beyond line-of-sight without material removal. The method applies a coating that triggers local surface remelting by activating a eutectic reaction during heat treatment. The associated liquid phase then wets and isothermally solidifies into a smoother surface. For Ti-6Al-4V fabricated with laser powder bed fusion, samples with and without TLP smoothing (using a Cu coating) were characterized with a suite of techniques, including mechanical testing, electron backscatter diffraction, synchrotron X-ray tomography, and fractography. TLP smoothing reduced surface roughness by 80% and amplified compressive residual stress at the surface by about 50%. With statistically equivalent virtual microstructures, crystal plasticity scrutinized the roles of phases, porosity, and surface roughness. Although the tensile strain-to-failure was reduced to 1% strain, the TLP smoothing process increased high-cycle fatigue strength by about 20% compared to control samples, pointing to future opportunities to optimize the new process through various coating compositions and heat treatment schedules. Overall, this work establishes a new paradigm for treating surfaces of materials for smoothness and compressive residual stress.

Additive manufacturing↗
DOE OSTI2024

Reactive Modified Epoxy Resin and Its Miscible Blends Based on Recycled Oligomers from Solvolysis

Chemical depolymerization of fully cured epoxy resin with 20% reactive modifier was successfully performed via a solvent-assisted solvolysis process into low molecular weight recyclable oligomers (RO) at 240 °C in a pressure vessel at 650 psi for 4 h. The thermoset epoxy resin was depolymerized into transparent brown viscous fluid with a higher viscosity than the uncured epoxy resin with approximately 93% yield. Different concentrations of the RO were homogeneously mixed with the pure epoxy resin, and their curing kinetics, viscosity, FTIR, mechanical properties, DMA, and cross-link density were investigated. The curing kinetics of the pure reactive modified epoxy resin (baseline) and its mixtures with RO of different concentrations were investigated under both isothermal and nonisothermal conditions using small amplitude oscillatory shear flow. The elastic and viscous moduli (G′ and G″), complex viscosity (η*), and tan δ values were evaluated at different curing times and temperatures. The G′, G″, and η* increased dramatically, while tan δ decreased strongly by several orders of magnitude at the gel point. The zero-shear viscosity (η 0 ) was determined from the angular frequency dependent on η* based on the Cross model for different blend compositions in the liquid state before curing. The composition dependence of η 0 showed a positive deviation from the linear mixing rule and was well described by the Lecyar model. Here, the apparent activation energy of curing (E a ) was also evaluated according to the Arrhenius equation and was found to be 46 ± 2 kJ/mol regardless of the different contents of RO. For all blends up to 40 wt % RO, only one tan δ peak systematically shifting to lower temperatures with increasing content of RO was observed in the DMA measurements, indicating that the epoxy resin and the RO are miscible with up to 40 wt % RO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

A statistical representation of bond coating oxidation under environmental barrier coatings

Environmental barrier coatings (EBCs) protect SiC-based ceramic matrix composites (CMCs) in turbine hot sections from high-temperature volatilization in combustion gases. The formation of a SiO 2 thermally grown oxide (TGO) is expected under the EBC after long-term operation. The oxidation resistance of the EBC is understood as a life-limiting factor for the CMC, and this work predicts long-term oxidation behavior under EBCs through a simple statistical approach. Specimens were exposed to 1350°C isothermal conditions for 100-h thermal cycles in flowing steam for up to 1000 h. The EBC morphology, SiO 2 thickness, and SiO 2 cracking behavior were assessed. Using thousands of SiO 2 thickness measurements across many millimeters of the interface, a realistic representation of the entire TGO was captured via a lognormal distribution. The lognormal fit parameters were extrapolated out to 25 000 h to assess the degree of SiO 2 growth, the spread of SiO 2 thicknesses related to the rough oxidizing interface, and percentages of the intermediate bond coating consumed. In conclusion, local interfacial defects from the coating deposition process are identified as local failure points for EBC—CMC systems.

SiO 2↗
DOE OSTI2026

Opportunities and challenges in process modeling and simulation of electrochemical systems

Electrochemical technologies have garnered intense interest in both academic research and industrial applications due to their potential to increase energy efficiency and reduce carbon footprint. However, electrochemical process fundamentals have been absent from the chemical process simulators available to millions of chemical engineers worldwide. To expedite process research and development of electrochemical technologies in the chemical industry, it is imperative that essential electrochemical process fundamentals be incorporated into process simulators to support modeling and simulation of electrochemical processes. Here, this study examines three process fundamentals key to the research and development of electrochemical processes: electrochemical reaction kinetics, electrolyte thermodynamics, and heat and mass transfer. It further illustrates application of these process fundamentals with a case study modeling an electrochemical process for the conversion of acrylonitrile to adiponitrile. The modeling example highlights the roles of applied voltage on reaction rates, and electron flow rates on the performance of electrochemical processes. It suggests that the applied voltage and electron flow rates are two unique concepts that should be included in simulators for electrochemical processes.

09 BIOMASS FUELS↗
DOE OSTI2025

An attention-based neural ordinary differential equation framework for modeling inelastic processes

To preserve strictly conservative behavior as well as model the variety of dissipative behavior displayed by solid materials, we propose a significant enhancement to the internal state variable-neural ordinary differential equation (ISV-NODE) framework. In this data-driven, physics-constrained modeling framework internal states are inferred rather than prescribed. The ISV-NODE consists of: (a) a stress model dependent on observable deformation and inferred internal state, and (b) a model of the evolution of the internal states. The enhancements to ISV-NODE proposed in this work are multifold: (a) a partially input convex neural network stress potential provides polyconvexity in terms of observed strain while leaving the inferred state unconstrained, and (b) an internal state flow model uses common latent features to inform novel attention-based gating and drives the flow of internal state only in dissipative regimes. We demonstrated that this architecture can accurately model dissipative and conservative behavior across an isotropic, isothermal elastic-viscoelastic-elastoplastic spectrum with three exemplars, while maintaining fundamental principles by design.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Transforming an Ionic Conductor into an Electronic Conductor via Crystallization: In Situ Evolution of Transference Numbers and Structure in (La,Sr)(Ga,Fe)O 3–x Perovskite Thin Films

Mixed-conducting perovskites are workhorse electrochemically active materials, but typical high-temperature processing compromises their catalytic activity and chemo-mechanical integrity. Low-temperature pulsed laser deposition of amorphous films plus mild thermal annealing is an emerging route to form homogeneous mixed conductors with exceptional catalytic activity, but little is known about the evolution of the oxide-ion transport and transference numbers during crystallization. Here the coupled evolution of ionic and electronic transport behavior and structure in room-temperature-grown amorphous (La,Sr)(Ga,Fe)O 3-x films as they crystallize is explored. In situ ac-impedance spectroscopy with and without blocking electrodes, simultaneous capturing-synchrotron-grazing-incidence X-ray diffraction, dc polarization, transmission electron microscopy, and molecular dynamics simulations to evaluate isothermal and non-isothermal crystallization effects and the role of grain boundaries on transference numbers is combined. Ionic conductivity increases by ≈2 orders of magnitude during crystallization, with even larger increases in electronic conductivity. Consequently, as crystallinity increases, LSGF transitions from a predominantly ionic conductor to a predominantly electronic conductor. The roles of evolving lattice structural order, microstructure, and defect chemistry are examined. Grain boundaries appear relatively nonblocking electronically but significantly blocking ionically. The results demonstrate that ionic transference numbers can be tailored over a wide range by tuning crystallinity and microstructure without having to change the cation composition.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Reverse phonon thermal flux from an applied electric field

In the phenomenon known as electron drag, a phonon thermal flux is established in a conducting crystal by an electric field applied under isothermal conditions through directed transfer of quasimomentum from the electronic charge current to the phonon subsystem. Prior understanding of this phenomenon involves a thermal current composed of low-frequency acoustic phonons that is in the same direction as the charge current. This results in an increase of the Peltier thermopower. Here, we show that it is also possible to establish a phonon thermal current that is in the opposite direction to the charge current, which we refer to as a reverse phonon thermal flux. We demonstrate this behavior both through a simple qualitative model and through first-principles calculations performed for three materials: p-type 𝜃-TaN, n-type BAs, and n-type Si. The reverse phonon flux is shown to arise through intervalley electron-phonon scattering processes involving high-frequency acoustic phonons. Unlike n-BAs and n-Si, the combined features in the band structure and phonon dispersions of p-type 𝜃-TaN promote a particularly large reverse phonon thermal flux comparable in magnitude to the oppositely directed thermal flux from low-frequency phonons. Finally, this work highlights a previously unrecognized behavior in the coupled electron-phonon system and advances our understanding of the rich physics of transport in solids.

lattice dynamics↗
DOE OSTI2026

Adsorption Hysteresis Under Control: Tuning Host–Guest Interactions via a Genetic Algorithm

Mesoporous adsorbent materials offer a large volumetric capacity; however, cyclic adsorption/desorption processes in these systems often suffer from hysteresis and may require a significant pressure swing to access this capacity. To mitigate hysteresis, a proposed strategy is to include nucleation sites on the walls of the mesoporous material to facilitate droplet and bubble formation, lowering the free energy barriers to the respective phase transitions. It is unclear, however, what combination of adsorbate− adsorbent interactions and spatial patterning would be beneficial for a given application, considering that improvements to some sorption properties may come at the expense of other attributes. To understand these interconnected observables, we examine two model systems, planar-slit and cylindrical pores with tunable interaction sites, using GPU-accelerated transition matrix Monte Carlo simulations. The simulations provide a free energy map of the pressure−adsorption space in a matter of minutes, which we use to track adsorption isotherm characteristics as a function of adsorbent properties. We then leverage the rapid acquisition of simulation data to construct a genetic algorithm to iteratively modify interaction sites of the slit-pore wall to minimize the hysteresis of this system without sacrificing uptake. We find that the adsorption branch of the isotherm is easily modulated via the average host−guest interaction strength, but desorption is only adjustable if there is a suitable bubble nucleation site. Within the context of a slit-pore system, we identify relative interaction strengths and patch sizes required to gain control over both branches of the hysteresis loop.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Accelerated and heterogeneous corrosion of Cr-doped uranium nitride fuel pellets

The steam oxidation of Cr-doped UN fuel pellets is analyzed during sequential isothermal holds up to 720 °C. In situ neutron diffraction results show how Cr is accommodated in a secondary U 2 CrN 3 phase, leading to the formation of a duplex UN/U 2 CrN 3 microstructure. Under corrosion, the oxidation of the two phases begins at 400 °C for UN and 430 °C for U 2 CrN 3 , respectively. Because the UN phase is preferentially oxidized in the presence of U 2 CrN 3 , addition of Cr in UN based nuclear fuel is found to accelerate the corrosion rate. At 430 °C the oxidation of UN in the UN/U 2 CrN 3 microstructure is ~ 5 times faster than pure UN, increasing to ~19 times faster at 460 °C. The oxidation of U 2 CrN 3 produces UO 2 via the formation of two transient intermediate phases. In situ neutron diffraction enables oxidation processes of UN and U 2 CrN 3 components to be followed separately within the two-phase system.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Influence of alloy solidification path on melt pool behavior in additive manufacturing

Numerical models used to study transport phenomena in laser-powder bed fusion processes often rely on assumptions and simplifications to reduce their computational expense. One common simplification is in the description of latent heat evolution during the solid-liquid phase change (i.e., the solidification pathway), justified by the fact that the mushy zone thickness is similar to the numerical grid spacing used for continuum transport models. The lack of resolution of transport phenomena in the mushy zone motivates the use of computationally convenient solidification paths such as linear or sigmoidal relationships over pathways derived from fundamental solidification theory such as equilibrium or Scheil models. In the present work, an uncertainty quantification (UQ) framework is used to analyze the influence of solidification pathway selection on the solidification dynamics and melt pool geometries in laser based additive manufacturing (AM) of IN625. Results show the solidification pathway has a quantifiable influence on the cooling rate at the liquidus isotherm, mushy zone thickness, and solidification time. Due to similarities in the latent heat evolution at the beginning of solidification, the equilibrium and Scheil models predict similar cooling rates near the liquidus isotherm, however the wider freezing range of Scheil leads to a wider mushy zone compared to equilibrium. The non-physical latent heat release profiles of sigmoidal and linear paths lead to significant overpredictions of cooling rates at the liquidus isotherm compared to equilibrium and Scheil. Finally, these results indicate that careful consideration should be given to the choice of solidification pathway to ensure reliable model predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Conductivity space isotherm behavior in quantum anomalous Hall devices

The quantum Hall effect (QHE) has enhanced accessibility to measure and disseminate electrical units, owed in part to the recently redefined International System of Units in 2019. Graphene remains one of the preferred options to realize the ohm despite the limitations of high magnetic fields to produce a robust QHE. Topological insulators, on the other hand, show promise in providing quantized resistance via the quantum anomalous Hall effect, a phenomenon that removes the need for magnetic fields during operation. To optimize future devices for metrological applications, it is important to gain a better understanding of magnetically doped topological insulators like Cr-doped bismuth antimony telluride. The application of differential conductivity space analyses offers a more sensitive way to analyze the data and distinguish between 2D and 3D transport behaviors. This is particularly important in thin films, where the transition between 2D and 3D behavior can be subtle. The ability to confidently determine the dimensionality of the transport is crucial for selecting appropriate theoretical models for future device optimization. Furthermore, this work identifies variable range hopping as the dominant transport mechanism in the 2D regime using a rigorous statistical analysis (via the Bayes factor). These elements assist in the understanding of microscopic processes that govern charge transport in these materials.

Tran, N. T. M. [National Inst. of Standards and Te↗
DOE OSTI2025

Evaluating Pretreatment Strategies with Modeling for Reducing Scaling Potential of Reverse Osmosis Concentrate: Insights from Ion Exchange and Activated Alumina

Reverse osmosis concentrate (ROC) treatment is critical for enhancing water recovery and minimizing concentrate volume for disposal, especially in regions facing water scarcity. This study investigates the application of ion exchange (IX) resins and activated alumina (AA) as pretreatment strategies to mitigate scaling in ROC due to high concentrations of total dissolved solids, hardness (Ca 2+ and Mg 2+ ), and silica. Through a series of Langmuir isotherms, continuous column experiments, and model simulation, two types of strong acid cation IX resins and three types of strong base anion IX resins alongside three types of AA were evaluated. Results indicate that AA exhibits superior performance in silica removal, achieving up to a 65% reduction and maintaining performance for up to 800 bed volume without reaching saturation. Model simulation of a secondary reverse osmosis treating ROC after the IX and AA pretreatment indicated an additional water recovery of ~70% using antiscalants. This study demonstrates the potential for achieving higher water recovery while also identifying opportunities for pretreatment improvement. Challenges such as the limited IX capacity treating ROC, which requires frequent regeneration and increases operational costs, along with the restricted regeneration capacity of AA, underscore the importance of innovation. These findings emphasize the critical need for developing advanced materials and optimized strategies to further enhance the efficiency of ROC treatment processes.

activated alumina↗