Search NASA⌕ Search

SEARCH · Search NASA

Results for “Imperfect interfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Controlling the structure and ferroic properties of strained epitaxial NiTiO3 thin films on sapphire by post-deposition annealing

Ferroelectrically induced weak ferromagnetism had been predicted earlier in compounds MTiO3 (M = Fe, Mn, Ni) with the LiNbO3-type structure. In order to stabilize this metastable structure by oxide heteroepitaxy, we attempted to grow epitaxial NiTiO3 films on the nonpolar, non-magnetic substrate Al2O3 by pulsed laser deposition. Given the structural imperfections of the as-deposited films arising from the large lattice mismatch, which resulted in weak ferroic ordering, we investigated the effect of post-synthesis annealing on the films’ properties. Our structural data from x-ray diffraction and electron microscopy suggest that the crystalline quality of the NiTiO3 films was greatly improved by annealing the films at 600-1000 oC for 8 hours, with new phase formation along the interface at 1000 oC. Our physical property characterization indicates increased ferromagnetism and polarization after 600 oC, but a change in the magnetic state to likely ferrimagnetism, and a loss of polarization after the 1000 oC treatment. Our results suggest that the ferroic domain properties of the NiTiO3 films can be favorably altered by post-synthesis heat treatment at the proper temperature to manipulate interfacial strain and enhance the multiferroic properties. Improvement in the ferroic properties can be explained by a combination of crystallite growth, interfacial strain relief, and thermodynamic phase stability arguments. At the same time, exceeding temperatures may drive the system to a thermodynamically more favored crystalline order, and eventually to phase segregation and decomposition.

Varga, Tamas↗

Growth of epitaxial CdTe thin films on amorphous substrates using single crystal graphene buffer

Traditionally, a high-quality CdTe film can only be grown on a single crystal substrate with a small lattice mismatch. We report the epitaxy of CdTe films on monolayer single crystal graphene buffered amorphous SiO 2 /Si(100) substrates, despite a 86% lattice mismatch between CdTe(111) and graphene. X-ray pole figure, electron backscatter diffraction mapping and transmission electron microscopy all confirm that the epitaxial CdTe films are composed of two domains: the primary and the Σ3 twin. The crystal quality of films is shown to improve as the post-deposition annealing temperature increases. However, the rotational misalignment in CdTe remains large even after annealing. Through density functional theory calculations on the charge transfer distribution at the interface of CdTe and graphene, it is found that the interface is dominated by the weak van der Waals interaction, which explains the large spread of in-plane orientation in CdTe films. Furthermore, the rotational misalignment in graphene itself is also confirmed to produce the large in-plane orientation spread in CdTe films. Although imperfect in epitaxy quality, this work demonstrates that monolayer single crystal graphene can buffer amorphous substrates for growing epitaxial films, and hence hints an opportunity for developing advanced thin film devices using graphene as a template.

36 MATERIALS SCIENCE↗

Processing and Testing of Thermoplastic Composite Cylindrical Shells Fabricated by Automated Fiber Placement

Two 61-cm-diameter eight-ply quasi-isotropic IM7/PEEK cylindrical shells were fabricated by automated fiber placement the NASA Langley Research Center using only infrared radiant heat to preheat the substrate and incoming composite uni-tape. The shells were characterized by ultrasonic c-scans for overall consolidation quality, and by optical microscopy and acid digestion for void content. Compression tests were also performed. Although the material used in the study was of generally poor quality due to numerous splits and dry fiber regions, the process was able to achieve a net reduction in void content in the as-placed component. Microscopy of the composite shells revealed well-consolidated, void-free interfaces. The two cylinders were then tested in uni-axial compression in a 1334 kN-capacity hydraulic test machine until buckling occurred. A geometrically nonlinear finite element analysis was conducted, and the differences between the predicted and measured values were 18.0 and 25.8%, respectively. Inclusion of measured imperfections of the cylinder into the analysis is expected to reduce these differences.

Hulcher, Anthony Bruce↗

2D Vacancy Confinement in Anatase TiO 2 for Enhanced Photocatalytic Activities

Abstract Light‐driven energy conversion devices call for the atomic‐level manipulation of defects associated with electronic states in solids. However, previous approaches to produce oxygen vacancy (V O ) as a source of sub‐bandgap energy levels have hampered the precise control of the distribution and concentration ofV O . Here, a new strategy to spatially confineV O at the homo‐interfaces is demonstrated by exploiting the sequential growth of anatase TiO 2 under dissimilar thermodynamic conditions. Remarkably, metallic behavior with high carrier density and electron mobility is observed after sequential growth of the TiO 2 films under low pressure and temperature (L‐TiO 2 ) on top of high‐quality anatase TiO 2 epitaxial films (H‐TiO 2 ), despite the insulating properties of L‐TiO 2 and H‐TiO 2 single layers. Multiple characterizations elucidate that theV O layer is geometrically confined within 4 unit cells at the interface, along with low‐temperature crystallization of upper L‐TiO 2 films; this 2DV O layer is responsible for the formation of in‐gap states, promoting photocarrier lifetime (≈300%) and light absorption. These results suggest a synthetic strategy to locally confine functional defects and emphasize how sub‐bandgap energy levels in the confined imperfections influence the kinetics of light‐driven catalytic reactions.

Chemistry↗

NASA Langley developments in response calculations needed for failure and life prediction

NASA Langley developments in response calculations needed for failure and life predictions are discussed. Topics covered include: structural failure analysis in concurrent engineering; accuracy of independent regional modeling demonstrated on classical example; functional interface method accurately joins incompatible finite element models; interface method for insertion of local detail modeling extended to curve pressurized fuselage window panel; interface concept for joining structural regions; motivation for coupled 2D-3D analysis; compression panel with discontinuous stiffener coupled 2D-3D model and axial surface strains at the middle of the hat stiffener; use of adaptive refinement with multiple methods; adaptive mesh refinement; and studies on quantity effect of bow-type initial imperfections on reliability of stiffened panels.

Housner, Jerrold M.↗

Additive Manufacturing, Design, Testing, and Fabrication: A Full Engineering Experience at JSC

I worked on several projects this term. While most projects involved additive manufacturing, I was also involved with two design projects, two testing projects, and a fabrication project. The primary mentor for these was Richard Hagen. Secondary mentors were Hai Nguyen, Khadijah Shariff, and fabrication training from James Brown. Overall, my experience at JSC has been successful and what I have learned will continue to help me in my engineering education and profession long after I leave. My 3D printing projects ranged from less than a 1 cubic centimeter to about 1 cubic foot and involved several printers using different printing technologies. It was exciting to become familiar with printing technologies such as industrial grade FDM (Fused Deposition Modeling), the relatively new SLA (Stereolithography), and PolyJet. My primary duty with the FDM printers was to model parts that came in from various sources to print effectively and efficiently. Using methods my mentor taught me and the Stratasys Insight software, I was able to minimize imperfections, hasten build time, improve strength for specific forces (tensile, shear, etc...), and reduce likelihood of a print-failure. Also using FDM, I learned how to repair a part after it was printed. This is done by using a special kind of glue that chemically melts the two faces of plastic parts together to form a fused interface. My first goal with SLA technology was to bring the printer back to operational readiness. In becoming familiar with the Pegasus SLA printer, I researched the leveling, laser settings, and different vats to hold liquid material. With this research, I was successfully able to bring the Pegasus back online and have successfully printed multiple sample parts as well as functional parts. My experience with PolyJet technology has been focused on an understanding of the abilities/limits, costs, and the maintenance for daily use. Still upcoming will be experience with using a composite printer that uses FDM technology to print plastic while laying an internal filament of Kevlar or carbon-fiber inside the printed material. It has been incredible being exposed to this range of technologies and I feel very fortunate to be ready for virtually any kind of printing technology I come across in the future. Design work played a part in my internship this term as well. Working with Hai Nguyen, I was able to design a set of testing tips and a test frame for use with an Arcjet. The testing tips will be made of several different materials that will possibly be used in the heat shield of the Orion space craft. These designs included technical drawings that were presented to the fabrication shop. The frame design was created from 80/20 (a popular brand of frame construction equipment) and included an order form with pricing for fabrication. An independent design was also done for the virtual reality lab. This design was to create a hand-controller based on a previous design. This final design was sent directly to a 3D printer without technical drawings. Overall, my design work has given me experience with using 80/20, helped improve my CAD (Computer Aided Design) proficiency, and increased my knowledge of how to set up technical drawings for fabrication. The final role I have played in this internship has been to assist with testing of the inflatable technology materials working Khadijah Shariff. I began the internship assisting with permeability testing with the initial plan to continue the testing independently after training. Unfortunately, the testing apparatus suffered a technical failure and had funding pulled which cancelled that portion of the project. Further testing with inflatable technology continued with tensile testing of various stitching methods. This testing took place over a two-days and concluded successfully. Final testing was to be more tensile testing but of straps used to connect various inflatable sections. Unfortunately, the needed grips for the tensile tests could not be located and put the testing on hold. It is possible this round of testing will still take place by the end of the internship if the grips can be found. Overall, this portion of the internship has helped me become familiar with one kind of permeability test as well as a popular tensile/compression testing machine. Finally, I also had the chance to be trained using a metal lathe for making very small tips for a soldering iron. These tips will be used to melt threaded brass inserts into 3D printed plastic. Working with James Brown, I was able to successfully machine a brass rod down to as little as 0.064 inches plus or minus 0.001 inches. It was very rewarding to learn how to best use the machine and become familiar with a skill that will undoubtedly be used again in the future. I have been told by several professional engineers that learning to use a lathe and mill will be invaluable skills in the field. This knocks 50 percent of that goal off and I look forward to learning the mill at some point in the future. As is apparent with this list of projects, my internship was not focused on a single over-arching goal. Instead, I was able to gain experience in a myriad of very different areas. I feel like my time here was spent bouncing from one project to the next. Though sometimes difficult to switch gears, it was very rewarding to be a part of so much in so little time. My career and education will be positively impacted by what I have learned at JSC. My experience with 3D printing has improved my ability to handle many issues that may come up in the future with multiple different technologies. The design work I took part in, especially creating technical drawings, will help me better present designs to any engineer or shop I will encounter. My testing experience has helped me become familiar with a popular kind of tensile test machine that will likely be similar to the kinds I will encounter in the future. Finally, my experience with fabrication has given me a rare opportunity, as an engineer, to take part in the fabrication of a part. This experience will help me better tailor my future designs for the manufacturing process and has given me an appreciation for detailed/delicate machining work. My experience at JSC has been successful and will continue to assist me for a long time within the engineering field.

Zusack, Steven↗

Method for preparing ultraflat, atomically perfect areas on large regions of a crystal surface by heteroepitaxy deposition

A novel method of forming large atomically flat areas is described in which a crystalline substrate having a stepped surface is exposed to a vapor of another material to deposit a material onto the substrate, which material under appropriate conditions self arranges to form 3D islands across the substrate surface. These islands are atomically flat at their top surface, and conform to the stepped surface of the substrate below at the island-substrate interface. Thereafter, the deposited materials are etched away, in the etch process the atomically flat surface areas of the islands transferred to the underlying substrate. Thereafter the substrate may be cleaned and annealed to remove any remaining unwanted contaminants, and eliminate any residual defects that may have remained in the substrate surface as a result of pre-existing imperfections of the substrate.

36 MATERIALS SCIENCE↗

A Numerical Study on the Edgewise Compression Strength of Sandwich Structures with Facesheet-Core Disbonds

Damage tolerant design approaches require determination of critical damage modes and flaw sizes in order to establish nondestructive evaluation detection requirements. A finite element model is developed to assess the effect of circular facesheet-core disbonds on the strength of sandwich specimens subjected to edgewise compressive loads for the purpose of predicting the critical flaw size for a variety of design parameters. Postbuckling analyses are conducted in which an initial imperfection is seeded using results from a linear buckling analysis. Both the virtual crack closure technique (VCCT) and cohesive elements are considered for modeling disbond growth. Predictions from analyses using the VCCT and analyses using cohesive elements are in good correlation. A series of parametric analyses are conducted to investigate the effect of core thickness and material, facesheet layup, facesheet-core interface properties, and curvature on the criticality of facesheet-core disbonds of various sizes. The results from these analyses provide a basis for determining the critical flaw size for facesheet-core disbonds subjected to edgewise compression loads and, therefore, nondestructive evaluation flaw detection requirements for this configuration.

Bergan, Andrew C.↗

About the deformation of ferroelectric hystereses

Studying ferroelectric hafnium oxide with focus on memory applications for the past years, discussions frequently involved the shape of measured polarization hystereses, its relation to the device performance, and how to optimize it. A perfect model-like hysteresis is of nearly rectangular shape and all deviations from this situation have to have a certain physical origin. Different phenomena and their impact on the shape of the polarization hystereses were reported in literature: Aging, imprint, fatigue, or dielectric interface layers to name a few examples. A collection of these phenomena is not easily found up to now. Thus, filling or at least reducing this gap is one of the goals of this work. Moreover, observing a pinched, slanted, or displaced hysteresis, it is quite tempting to try the reverse approach: a derivation of potential structural origins for this curve shape. First, the basics of the dynamic hysteresis measurement and the ferroelectric memories are briefly reviewed. The figures of interest are derived to ensure a proper assessment of imperfections in the hysteresis shape and their influence. It is discussed how a closer look on the polarization loop helps to draw conclusions on what might have caused such a shape or at least how to rule out some phenomena if the expected indications are not reflected in the present curve. Of course, further structural or electrical studies, as they are exemplarily pointed out, are indispensable to find the root cause(s) for the deviations from the ideal hysteresis. But sophisticated methods are not always accessible straightaway and, moreover, a pointer on where to start is always helpful. Especially, the transient currents recorded during a dynamic hysteresis measurement are stressed as a valuable instrument for this purpose. Despite their known potential, these currents are seldom shown in literature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NDE of Space Shuttle Solid Rocket Motor field joint

One of the most critical areas for inspection in the Space Shuttle Solid Rocket Motors is the bond between the steel case and rubber insulation in the region of the field joints. The tang-and-clevis geometry of the field joints is sufficiently complex to prohibit the use of resonance-based techniques. One approach we are investigating is to interrogate the steel-insulation bondline in the tang and clevis regions using surface-travelling waves. A low-frequency contact surface wave transmitting array transducer is under development at our laboratory for this purpose. The array is placed in acoustic contact with the steel and surface waves are launched on the inside surface or the clevis leg which propagate along the steel-insulation interface. As these surface waves propagate along the bonded surface, the magnitude of the ultrasonic energy leaking into the steel is monitored on the outer surface of the case. Our working hypothesis is that the magnitude of energy received at the outer surface of the case is dependent upon the integrity of the case-insulation bond, with less attenuation for propagation along a disbond due to imperfect acoustic coupling between the steel and rubber. Measurements on test specimens indicate a linear relationship between received signal amplitude and the length of good bend between the transmitter and receiver, suggesting the validity of this working hypothesis.

Patrick H. Johnston↗

Technology-enabled Airborne Spacing and Merging

Over the last several decades, advances in airborne and groundside technologies have allowed the Air Traffic Service Provider (ATSP) to give safer and more efficient service, reduce workload and frequency congestion, and help accommodate a critically escalating traffic volume. These new technologies have included advanced radar displays, and data and communication automation to name a few. In step with such advances, NASA Langley is developing a precision spacing concept designed to increase runway throughput by enabling the flight crews to manage their inter-arrival spacing from TRACON entry to the runway threshold. This concept is being developed as part of NASA s Distributed Air/Ground Traffic Management (DAG-TM) project under the Advanced Air Transportation Technologies Program. Precision spacing is enabled by Automatic Dependent Surveillance-Broadcast (ADS-B), which provides air-to-air data exchange including position and velocity reports; real-time wind information and other necessary data. On the flight deck, a research prototype system called Airborne Merging and Spacing for Terminal Arrivals (AMSTAR) processes this information and provides speed guidance to the flight crew to achieve the desired inter-arrival spacing. AMSTAR is designed to support current ATC operations, provide operationally acceptable system-wide increases in approach spacing performance and increase runway throughput through system stability, predictability and precision spacing. This paper describes problems and costs associated with an imprecise arrival flow. It also discusses methods by which Air Traffic Controllers achieve and maintain an optimum interarrival interval, and explores means by which AMSTAR can assist in this pursuit. AMSTAR is an extension of NASA s previous work on in-trail spacing that was successfully demonstrated in a flight evaluation at Chicago O Hare International Airport in September 2002. In addition to providing for precision inter-arrival spacing, AMSTAR provides speed guidance for aircraft on converging routes to safely and smoothly merge onto a common approach. Much consideration has been given to working with operational conditions such as imperfect ADS-B data, wind prediction errors, changing winds, differing aircraft types and wake vortex separation requirements. A series of Monte Carlo simulations are planned for the spring and summer of 2004 at NASA Langley to further study the system behavior and performance under more operationally extreme and varying conditions. This will coincide with a human-in-the-loop study to investigate the flight crew interface, workload and acceptability.

Hull, James↗

Extended Cycling through Rigid Block Copolymer Electrolytes Enabled by Reducing Impurities in Lithium Metal Electrodes

Successful prevention of lithium dendrite growth would enable the use of lithium metal as an anode material in next-generation rechargeable batteries. Mechanically stiff block copolymer electrolytes have been shown to prolong the life of lithium metal cells by partially suppressing lithium dendrite growth. Yet, impurity particles that are invariably present in the lithium metal nucleate electrodeposition defects that eventually lead to short circuits. Here, we use X-ray tomography to study the morphology of electrodeposited lithium in symmetric cells containing a block copolymer electrolyte. An "electrochemical filtering" treatment was performed on these cells to reduce the concentration of impurity particles near the electrode-electrolyte interface, and cells were cycled to determine the effects of the treatment on lifetime. Depending on the treatment details, the average charge passed before failure was improved by 30-400%. For a cell in which the treatment was most effective, the cycle life was increased by more than an order of magnitude, and the measured number of deposition defects per area was negligible. Other treated cells, however, in which the treated lithium was imperfect, had a higher number of deposition defects per area compared to control cells. A majority of the deposition defects in treated cells were confined within the electrodes. In contrast, most of the deposition defects seen in the control cells were protrusions that invaded the electrolyte phase. The increased lifetime in these imperfectly treated cells was not due to a reduction in the number of deposition defects per area, but rather due to the differences in defect morphology. These findings motivate the development of deposition defect- and impurity-free lithium metal electrodes.

25 ENERGY STORAGE↗

Directional solidification in an imperfect furnace

The upward directional solidification of a binary alloy in which the rejected solute is more dense than the solvent is considered. The system is stably stratified both thermally and solutally. If heat is lost through the sidewalls, horizontal thermal gradients drive a steady double-diffusive convection. Solidification cells with small aspect ratios (width/length) A are considered, and asymptotic solutions to the steady double-diffusive system are obtained as A tends to 0 under the assumption heat losses are also small. When the thermal Grashof number is large, buoyancy boundary layers are at the sidewalls. The shape of the crystal-melt interface is determined by the coupled effects of local thermodynamic equilibrium, diffusion and convection.

Brattkus, K.↗

Vibrations of three-dimensional pipe systems with acoustic coupling

A general algorithm is developed to calculate the beam-type dynamic response of three dimensional multiplane finite length pipe systems, consisting of elbow and straight ducts with continuous interfaces. Emphasis is on secondary acoustic wave effects giving rise to coupling mechanisms; and the simulation accounts for one-dimensional elastoacoustic coupling from a plane acoustic wave and secondary loads resulting from wave asymmetries. The transfer matrix approach is adopted in modeling the elastodynamics of each duct, with allowance for distribution loads. Secondary loads from plane wave distortion are considered with a solution of the Helmholtz equation in an equivalent rigid waveguide, and effects of path imperfection are introduced as a perturbation from the hypothetical perfectly straight pipe. Computations indicate that the one-dimensional acoustic assumption is valid for frequencies below one-half the first cut-off frequency, and the three-dimensional acoustic effects produce an increase in response levels near and above cut-off.

El-Raheb, M.↗

Development and Applications of an eReaxFF Force Field for Graphitic Anodes of Lithium-Ion Batteries

Graphene is one of the most promising materials for lithium-ion battery anodes due to its superior electronic conductivity, high surface area for lithium intercalation, fast ionic diffusivity and enhanced specific capacity. A reliable description of many battery processes requires an explicit description of electrochemical interactions involving electrons. A detailed atomistic modeling of electronic conduction and non-zero voltage simulations of graphitic materials require the inclusion of an explicit electronic degree of freedom. To enable large length- and time-scale simulations of electron conduction in graphitic anodes, we developed an eReaxFF force field concept describing graphitic materials with an explicit electron. The newly developed force field, verified against quantum chemistry-based data describing, amongst others, electron affinities and equation of states, reproduces the qualitative behavior of electron conductivity in pristine and imperfect graphitic materials at different applied temperatures and voltages. In addition, excess electron localization near a defect site estimated from eReaxFF simulations agree quite well with the corresponding density functional theory calculations. Here, our eReaxFF simulations show the initiation of lithium-metal-plating driven by electron transfer from the graphene surface to the exposed lithium ions demonstrating the method’s potential for studying lithium-graphene interactions with explicit electrons and explain many unresolved electrode and electrode-electrolyte interface processes.

25 ENERGY STORAGE↗

Fracture problems in composite materials

A series of fracture problems in composite materials are identified, their methods of solution are briefly discussed, and some sample results are presented. The main problem of interest is the determination of the stress state in the neighborhood of localized imperfections such as cracks and inclusions which may exist in the composite. Particular emphasis is placed on the evaluation of quantities such as the stress intensity factors, the power of the stress singularity, and the strain energy release rate, which may be used directly or indirectly in connection with an appropriate fracture criterion for the prediction of fracture initiation and propagation load levels. The topics discussed include a crack in layered composites, a crack terminating at and going through a bi-material interface, a penny-shaped crack in a filament-reinforced elastic matrix, and inclusion problems in bonded materials.

Erdogan, F.↗

Multi-Stage Modeling With Recourse Decisions for Solving Stochastic Complementarity Problems With an Application in Energy

This paper presents a multi-stage model with recourse decisions for solving complementarity problems in a competitive electricity market under uncertainty, while also considering renewable energy technologies and battery storage utilization. The model is based on a Nash-Cournot formulation of imperfect competition among power producers. We analyze the value of variable renewable energy (VRE) and battery storage under different uncertainties, such as demand level and VRE availability. To illustrate the proposed model, we apply it to three- bus five-player model and analyze different cases varying costs, including a user-optimal perspective (with market power) and a system-optimal perspective (with central planning). We also consider the potential for congestion in the system by restricting the transmission capacity between a single interface that connects two buses. Our findings show that increasing the battery storage capacity results in a decrease in the need for perfect information about future uncertainties. Additionally, as the model allows for more uncertainty, it becomes more apparent that the stochastic mixed complementarity problem (MCP) has an advantage over a deterministic equivalent. We propose the use of the Value of the Stochastic Equilibrium Solution (VSES) as a quality metric to compare the stochastic MCP with its deterministic equivalent. Overall, expanding battery storage capacity can lower the maximum, mean, and variance values of delivered prices, but there are diminishing returns to this approach.

24 POWER TRANSMISSION AND DISTRIBUTION↗