Search NASA⌕ Search

SEARCH · Search NASA

Results for “Insert gas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

On the flaring of cometary plasma tails

Assuming that hypersonic pressure balance with the solar wind governs the shape of plasma tails, it is found that the gas pressure of tail ions and the magnetic field strength at the flanks of the ionopause control the flaring state. The gas pressure exhibits the larger effect: for constant pressures above a certain critical value, the tail flares essentially without limit, while for smaller values the tail flares only near the head (becoming cylindrical at greater distances). The influence of the magnetic field is that the tail flares to larger distances the higher the field strength at the flanks of the ionopause. The observed variability in flaring (and the implied differences in gas pressure and magnetic field) are throught to be the result of changes in the position and shape of the sunward cometary ionopause. Insertion of reasonable comet and solar wind parameters into the pressure balance equations is found to give good agreement with the observations.

Ershkovich, A. I.↗
NASA NTRS1991

Measurement of the performance of a spiral wound polyimide regenerator in a pulse tube refrigerator

A regenerator for use in a pulse tube refrigerator has been constructed from a polyimide (polypyromellitimide or PPMI) whose small ratio of thermal conductivity to heat capacity make it a good candidate for a regenerator material in cryocoolers. The regenerator was fabricated using 25 micron thick photoresist strips bonded to a 50 micron thick sheet of PPMI. This composite sheet was wound in jelly-roll fashion around a mandrel and inserted into the regenerator housing. The photoresist strips, formed using a photolithographic technique, provided a 25 micron spacing for the axial flow of gas between each layer of PPMI. Ineffectiveness results are presented for this material under actual operating conditions in a pulse tube refrigerator and compared with a numerical model. The numerical model indicated that a polyimide regenerator would perform much better than one constructed of stainless steel screen, but the experimental results showed the opposite behavior. Measured values for the ineffectiveness were 0.003 for the stainless steel screen and 0.017 for the polyimide.

Rawlins, Wayne↗
NASA NTRSDate not supplied

Development of a CubeSat-Scale Green Monopropellant Propulsion System for NASA’s Lunar Flashlight Mission

NASA’s Lunar Flashlight is a low-cost 6U CubeSat whose mission is to search for ice and mineral deposits inside of the scattered craters at Moon’s southern pole. To conduct its primary science mission, Lunar Flashlight must be placed in a stable lunar polar orbit which requires the utilization of an on-board propulsion system. However, to this date, most CubeSats have been propelled by cold-gas or electric propulsion systems that have proven to scale well but lack sufficient impulse to conduct large ΔV maneuvers such as orbit insertions. To this end, the Lunar Flashlight mission has chosen to utilize a custom-designed green monopropellant propulsion system developed by the Georgia Institute of Technology under the leadership ofNASA’s Marshall Space Flight Center and support from the Jet Propulsion Laboratory. The developed system is capable of providing more than the required propulsive capability for full mission success while fitting inside of a 2.5U volume and weighing less than six kilograms. The system utilizes the Advanced Spacecraft Energetic Non Toxic (ASCENT) green monopropellant that provides higher specific impulse compared to traditional hydrazine while also being safer to handle. If successful, the presented propulsion system will enable Lunar Flashlight to be the first CubeSat to reach the Moon, the first to conduct an orbit insertion, and will be the firstCubeSat demonstration of the ASCENT propellant.

Grayson Huggins↗
NASA NTRS1957

Cooling Performance and Structural Reliability of a Modified Corrugated-insert Air-cooled Turbine Blade with an Integrally Cast Shell and Base

A modified corrugated-insert blade with integrally cast shell and base was developed. This blade was as light as a conventional fabricated corrugated-insert blade. Of four test blades operated in a full-scale turbojet engine, one failed after about 15 hours operation at an inlet gas temperature of 1670 degrees F, a coolant-flow ratio of 0.0064, and a 1/3-span centrifugal stress of approximately 28,000 psi. Three other test blades ran for approximately 16, 31, and 36 hours without failure at similar conditions.

Freche, John C↗
NASA NTRS2021

Development of a CubeSat-Scale Green Monopropellant Propulsion System for NASA's Lunar Flashlight Mission

NASA's Lunar Flashlight is a low-cost 6U CubeSat whose mission is to search for ice and mineral deposits inside of the scattered craters at Moon's southern pole. To conduct its primary science mission, Lunar Flashlight must be placed in a stable lunar polar orbit which requires the utilization of an on-board propulsion system. However, to this date, most CubeSats have been propelled by cold-gas or electric propulsion systems that have proven to scale well but lack sufficient impulse to conduct large $\Delta V$ maneuvers such as orbit insertions. To this end, the Lunar Flashlight mission has chosen to utilize a custom-designed green monopropellant propulsion system developed by the Georgia Institute of Technology under the leadership of NASA's Marshall Space Flight Center and support from the Jet Propulsion Laboratory. The developed system is capable of providing more than the required propulsive capability for full mission success while fitting inside of a 2.5U volume and weighing less than six kilograms. The system utilizes the Advanced Space Craft Energetic Non Toxic (ASCENT) green monopropellant that provides higher specific impulse compared to traditional hydrazine while also being safer to handle. If successful, the presented propulsion system will enable Lunar Flashlight to be the first CubeSat to reach the Moon, the first to conduct an orbit insertion, and will be the first CubeSat demonstration of the ASCENT propellant.

Kowalkowski, Matthew↗
NASA NTRS1992

Increase of stagnation pressure and enthalpy in shock tunnels

High stagnation pressures and enthalpies are required for the testing of aerospace vehicles such as aerospace planes, aeroassist vehicles, and reentry vehicles. Among the most useful ground test facilities for performing such tests are shock tunnels. With a given driver gas condition, the enthalpy and pressure in the driven tube nozzle reservoir condition can be varied by changing the driven tube geometry and initial gas fill pressure. Reducing the driven tube diameter yields only very modest increases in reservoir pressure and enthalpy. Reducing the driven tube initial gas fill pressure can increase the reservoir enthalpy significantly, but at the cost of reduced reservoir pressure and useful test time. A new technique, the insertion of a converging section in the driven tube is found to produce substantial increases in both reservoir pressure and enthalpy. Using a one-dimensional inviscid full kinetics code, a number of different locations and shapes for the converging driven tube section were studied and the best cases found. For these best cases, for driven tube diameter reductions of factors of 2 and 3, the reservoir pressure can be increased by factors of 2.1 and 3.2, respectively and the enthalpy can be increased by factors of 1.5 and 2.1, respectively.

Bogdanoff, David W.↗
NASA NTRS2020

Enabling Entry Technologies for Ice Giant Missions

The highest priority science goals for Ice Giant missions are: 1) Interior structure of the Planet, and 2) Bulk composition that includes isotopes and noble gases. The interaction between the planetary interior and the atmosphere requires sustained global measurements. Noble gas and Isotope measurements require in situ measurement. Drag modulated aerocapture utilizing ADEPT offers more mass delivered to the Ice Giants than with propulsive orbit insertion. The Galileo Probe entered at a ‘hot’ spot which created interpretation challenges. Juno is providing valuable orbital measurements, but without in situ measurements the story is incomplete. Planetary scientists interested in Ice Giant missions should perform mission design studies with these new Entry System technologies to assess the feasibility within the context of the international collaboration framework. A mission architecture that includes probe(s) along with an orbiting spacecraft can deploy the probes at the desired location while taking simultaneous measurements from orbit to provide invaluable data that can correlate both global and local measurements. Entry System Technologies currently being developed by NASA are poised to enable missions that position the Orbiter & Probes through drag modulated aerocapture (ADEPT), and HEEET enables the Probes to survive the extreme environments encountered for entry into the atmospheric interior.

Venkatapathy, E.↗
NASA NTRS2007

Design of a Resistively Heated Thermal Hydraulic Simulator for Nuclear Rocket Reactor Cores

A preliminary design study is presented for a non-nuclear test facility which uses ohmic heating to replicate the thermal hydraulic characteristics of solid core nuclear reactor fuel element passages. The basis for this testing capability is a recently commissioned nuclear thermal rocket environments simulator, which uses a high-power, multi-gas, wall-stabilized constricted arc-heater to produce high-temperature pressurized hydrogen flows representative of reactor core environments, excepting radiation effects. Initially, the baseline test fixture for this non-nuclear environments simulator was configured for long duration hot hydrogen exposure of small cylindrical material specimens as a low cost means of evaluating material compatibility. It became evident, however, that additional functionality enhancements were needed to permit a critical examination of thermal hydraulic effects in fuel element passages. Thus, a design configuration was conceived whereby a short tubular material specimen, representing a fuel element passage segment, is surrounded by a backside resistive tungsten heater element and mounted within a self-contained module that inserts directly into the baseline test fixture assembly. With this configuration, it becomes possible to create an inward directed radial thermal gradient within the tubular material specimen such that the wall-to-gas heat flux characteristics of a typical fuel element passage are effectively simulated. The results of a preliminary engineering study for this innovative concept are fully summarized, including high-fidelity multi-physics thermal hydraulic simulations and detailed design features.

Litchford, Ron J.↗
NASA NTRS1977

Blade retainer assembly

A retaining assembly is provided for locking radially extending blades in a rotor disc associated with a gas turbine engine. The assembly includes a pair of spaced apart lugs axially extending from one side of the disc to form an access gap for insertion of a blade tang into a dovetail slot in the rotor disc. A pair of axially aligned inwardly facing recesses are disposed in the lugs. A retaining member resides in the recesses and extends across the gap to preclude egress of the blade tang from the dovetail slot. The retaining member includes at least one axially extending protrusion adapted to radially overlap and abuttingly engage a radially inwardly facing abutment surface on the lugs.

Luebering, G. W.↗
NASA NTRS2001

Life Model of Hollow Cathodes Using a Barium Calcium Aluminate Impregnated Tungsten Emitter

Hollow cathodes with barium calcium aluminate impregnated tungsten emitters for thermionic emission are widely used in electric propulsion. These high current, low power cathodes are employed in ion thrusters, Hall thrusters, and on the International Space Station in plasma contactors. The requirements on hollow cathode life are growing more stringent with the increasing use of electric propulsion technology. The life limiting mechanism that determines the entitlement lifetime of a barium impregnated thermionic emission cathode is the evolution and transport of barium away from the emitter surface. A model is being developed to study the process of barium transport and loss from the emitter insert in hollow cathodes. The model accounts for the production of barium through analysis of the relevant impregnate chemistry. Transport of barium through the approximately static gas is also being treated. Finally, the effect of temperature gradients within the cathode are considered.

Kovaleski, S. D.↗
NASA NTRS2012

Development of a Deep-Penetrating, Compact Geothermal Heat Flow System for Robotic Lunar Geophysical Missions

Geothermal heat flow measurements are a high priority for the future lunar geophysical network missions recommended by the latest Decadal Survey of the National Academy. Geothermal heat flow is obtained as a product of two separate measurements of geothermal gradient and thermal conductivity of the regolith/soil interval penetrated by the instrument. The Apollo 15 and 17 astronauts deployed their heat flow probes down to 1.4-m and 2.3-m depths, respectively, using a rotary-percussive drill. However, recent studies show that the heat flow instrument for a lunar mission should be capable of excavating a ~3-m deep hole to avoid the effect of potential long-term changes of the surface thermal environment. For a future robotic geophysical mission, a system that utilizes a rotary/percussive drill would far exceed the limited payload and power capacities of the lander/rover. Therefore, we are currently developing a more compact heat flow system that is capable of 3-m penetration. Because the grains of lunar regolith are cohesive and densely packed, the previously proposed lightweight, internal hammering systems (the so-called moles ) are not likely to achieve the desired deep penetration. The excavation system for our new heat flow instrumentation utilizes a stem which winds out of a pneumatically driven reel and pushes its conical tip into the regolith. Simultaneously, gas jets, emitted from the cone tip, loosen and blow away the soil. Lab tests have demonstrated that this proboscis system has much greater excavation capability than a mole-based heat flow system, while it weighs about the same. Thermal sensors are attached along the stem and at the tip of the penetrating cone. Thermal conductivity is measured at the cone tip with a short (1- to 1.5-cm long) needle sensor containing a resistance temperature detector (RTD) and a heater wire. When it is inserted into the soil, the heater is activated. Thermal conductivity of the soil is obtained from the rate of temperature increase during the heating. By stopping during the excavation, it is possible to measure thermal conductivities at different depths. The gas jets are turned off when the penetrating cone reaches the target depth. Then, the stem pushes the needle sensor into the undisturbed soil at the bottom of the hole and carries out a thermal conductivity measurement. When the measurement is complete, the system resumes excavation. RTDs, placed along the stem at short (approx 30 cm) intervals, will monitor long-term temperature stability of the subsurface. Temperature in the shallow subsurface would fluctuate with the diurnal, annual, and precession cycles of the Moon. These thermal waves penetrate to different depths into the regolith. Longterm monitoring of the subsurface temperature would allow us to accurately delineate these cyclic signals and separate them from the signal associated with the outward flow of the Moon s endogenic heat. Further, temperature toward bottom of the 3-m hole should be fairly stable after the heat generated during the excavation dissipates into the surrounding soil. The geothermal gradient may be determined reliably from temperature measurements at the RTDs near the bottom. In order to minimize the heat conduction along the stem from affecting the geothermal gradient measurements, we plan to use low-conductive materials for the stem and develop a mechanism to achieve close coupling between the RTDs and the wall of the excavated hole.

Nagihara, Seiichi↗
NASA NTRS1982

Theory of metal atom-water interactions and alkali halide dimers

Theoretical studies of the interactions of metal atoms with water and some of its isoelectronic analogs, and of the properties of alkali halides and their aggregates are discussed. Results are presented of ab initio calculations of the heats of reaction of the metal-water adducts and hydroxyhydrides of Li, Be, B, Na, Mg, and Al, and of the bond lengths and angles an; the heats of reaction for the insertion of Al into HF, H2O, NH3, H2S and CH3OH, and Be and Mg into H2O. Calculations of the electron affinities and dipole moments and polarizabilities of selected gas phase alkali halide monomers and dimers are discussed, with particular attention given to results of calculations of the polarizability of LiF taking into account electron correlation effects, and the polarizability of the dimer (LiF)2.

Jordan, K. D.↗
NASA NTRS1985

Orbital Maneuvering system design evolution

Preliminary design considerations and changes made in the baseline space shuttle orbital maneuvering system (OMS) to reduce cost and weight are detailed. The definition of initial subsystem requirements, trade studies, and design approaches are considered. Design features of the engine, its injector, combustion chamber, nozzle extension and bipropellant valve are illustrated and discussed. The current OMS consists of two identical pods that use nitrogen tetroxide (NTO) and monomethylhydrazine (MMH) propellants to provide 1000 ft/sec of delta velocity for a payload of 65,000 pounds. Major systems are pressurant gas storage and control, propellant storage supply and quantity measurement, and the rocket engine, which includes a bipropellant valve, an injector/thrust chamber, and a nozzle. The subsystem provides orbit insertion, circularization, and on orbit and deorbit capability for the shuttle orbiter.

Gibson, C.↗
NASA NTRS1961

Experimental Investigation of an Air-Cooled Turbine Operating in a Turbojet Engine at Turbine Inlet Temperatures up to 2500 F

An experimental investigation was made of an air-cooled turbine at average turbine inlet temperatures up to 2500 F. A modified production-model 12-stage axial-flow-compressor turbojet engine operating in a static sea-level stand was used as the test vehicle. The modifications to the engine consisted of the substitution of special combustor and turbine assemblies and double-walled exhaust ducting for the standard parts of the engine. All of these special parts were air-cooled to withstand the high operating temperatures of the investigation. The air-cooled turbine stator and rotor blades were of the corrugated-insert type. Leading-edge tip caps were installed on the rotor blades to improve leading-edge cooling by diverting the discharge of coolant to regions of lower gas pressure toward the trailing edge of the blade tip. Caps varying in length from 0.15- to 0.55-chord length were used in an attempt to determine the optimum cap length for this blade. The engine was operated over a range of average turbine inlet temperatures from about 1600 to about 2500 F, and a range of average coolant-flow ratios of 0.012 to 0.065. Temperatures of the air-cooled turbine rotor blades were measured at all test conditions by the use of thermocouples and temperature-indicating paints. The results of the investigation indicated that this type of blade is feasible for operation in turbojet engines at the average turbine inlet temperatures and stress levels tested(maximums of 2500 F and 24,000 psi, respectively). An average one-third-span blade temperature of 1300 F could be maintained on 0.35-chord tip cap blades with an average coolant-flow ratio of about 0.022 when the average turbine inlet temperature was 2500 F and cooling-air temperature was about 260 F. All of the leading-edge tip cap lengths improved the cooling of the leading-edge region of the blades, particularly at low average coolant-flow ratios. At high gas temperatures, such parts as the turbine stator and the combustor liners are likely to be as critical as the turbine rotor blades.

Cochran, Reeves P.↗
NASA NTRS2000

Preventing Damaging Pressure Gradients at the Walls of an Inflatable Space System

An inflatable structural system to deploy a space system such as a solar shield, an antenna or another similar instrument requires a stiffening element after it is extended by the inflated gas pressure. The stiffening element has to be packaged in folded configuration before the deployment. It must be relatively small, lightweight, non-damaging to the inflated system and be able to become stiff in a short time. One stiffening method is to use a flexible material inserted in the deployable system, which, upon a temperature curing, can become stiff and is capable of supporting the entire structure. There are two conditions during the space operations when the inflated volume could be damaged: during the transonic region of the launch phase and when the curing of the rigidizing element occurs. In both cases, an excess of pressure within the volume containing the rigid element could burst the walls of the low-pressure gas inflated portion of the system. This paper investigates those two conditions and indicates the vents, which will prevent those damaging overpressures. Vent openings at the non-inflated volumes have been calculated for the conditions existing during the launch. Those vents allow the initially folded volume to exhaust the trapped atmospheric gas at approximately the same rate as the ambient pressure drops. That will prevent pressure gradients across the container walls which otherwise could be as high as 14.7 psi. The other condition occurring during the curing of the stiffening element has been investigated. This has required the testing of the element to obtain the gas generation during the curing and the transformation from a pliable material to a rigid on The tested material is a composite graphite/epoxy weave. The outgassing of the uncured sample at 121 deg Celcius was carried with the Cahn Microbalance and with other outgassing facilities including the micro-CVCM ASTM E-595 facility. The test provided the mass of gas evolved during the test. That data, including the chemical nature of the evolved gas, provided the data for the calculation of the pressure produced within the volume. The evaluation of the areas of the vents that would prevent excessive pressures and provide a rapid release of the gas away from contamination sensitive surfaces has be carried out. The pressure decay with time has been indicated.

Scialdone, John J.↗
NASA NTRS2000

Preventing Damaging Pressure Gradients at the Walls of an Inflatable Space System

An inflatable structural system to deploy a space system such as a solar shield, an antenna or another similar instrument, requires a stiffening element after it is extended by the inflated gas pressure. The stiffening element has to be packaged in a folded configuration before the deployment. It must be relatively small, lightweight, non-damaging to the inflated system, and be able to become stiff in a short time. One stiffening method is to use a flexible material inserted in the deployable system, which, upon a temperature curing, can become stiff and is capable to support the entire structure. There are two conditions during the space operations when the inflated volume could be damaged: during the transonic region of the launch phase and when the curing of the rigidizing element occurs. In both cases, an excess of pressure within the volume containing the rigid element could burst the walls of the low-pressure gas inflated portion of the system. This paper investigates those two conditions and indicates the vents, which will prevent those damaging overpressures. Vent openings at the non-inflated volumes have been calculated for the conditions existing during the launch. Those vents allow the initially folded volume to exhaust the trapped atmospheric gas at approximately the same rate as the ambient pressure drops. That will prevent pressure gradients across the container walls which otherwise could be as high as 14.7 psi. The other condition occurring during the curing of the stiffening element has been investigated. This has required the testing of the element to obtain the gas generation during the curing and the transformation from a pliable material to a rigid one. The tested material is a composite graphite/epoxy weave. The outgassing of the uncured sample at 121C was carried with the Cahn Microbalance and with other outgassing facilities including the micro-CVCM ASTM E-595 facility. The tests provided the mass of gas evolved during the test. That data, including the chemical nature of the evolved gas, provided the data for the calculation of the pressure produced within the volume. The evaluation of the areas of the vents that would prevent excessive pressures and provide a rapid release of the gas away from contamination sensitive surfaces has been carried out. The pressure decay with time has been indicated.

Scialdone, John J.↗
NASA NTRS1986

Precise-Conductance Valve Insert

Valve modification provides two operating modes fully open and small, precise leak. Copper insert with radially oriented holes allows small, controllable, precise effusion rate when valve closed or nearly unobstructed flow when valve open. Numerous applications in surface physics, vacuum physics, materials science, gas kinetics, thin films, and other areas of research requiring measured flows of gas into or out of system.

Outlaw, R. A.↗
NASA NTRS1995

Magnetic heat pump flow director

A fluid flow director is disclosed. The director comprises a handle body and combed-teeth extending from one side of the body. The body can be formed of a clear plastic such as acrylic. The director can be used with heat exchangers such as a magnetic heat pump and can minimize the undesired mixing of fluid flows. The types of heat exchangers can encompass both heat pumps and refrigerators. The director can adjust the fluid flow of liquid or gas along desired flow directions. A method of applying the flow director within a magnetic heat pump application is also disclosed where the comb-teeth portions of the director are inserted into the fluid flow paths of the heat pump.

Howard, Frank S.↗