Static calibration of an ejector unit for simulation of jet engines in small-scale wind-tunnel models
Static calibration of ejector unit for simulation of jet engines in small-scale wind tunnel models of VTOL aircraft
EJECTOR↗
SEARCH · Search NASA
Results for “Jet Engines”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Analytical investigation of ram-jet-engine performance in flight Mach number range from 3 to 7
An analytical investigation was made of the performance of isolated ram-jet engines in the flight Mach number range from 3 to 7 for two types of diffuser, a high-efficiency diffuser, and a normal-shock diffuser. The fuel was assumed to be a hydrocarbon similar to gasoline. The conclusions reached are: (1) a design altitude of about 100,000 feet is desirable for a high-efficiency high Mach number ram jet on the basis of engine construction and performance; and (2) although greater thrust could be obtained with other fuels, gasoline provides sufficient energy release for maximum engine efficiency in the flight Mach number range investigated. The maximum engine efficiency calculated was 0.47, which occurred at a Mach number of 5. At a Mach number of 7, the maximum propulsive-thrust coefficient was 0.57.
ENGINES, RAM JET↗
Investigation of Three Low-temperature-ratio Combustor Configurations in a 48-inch-diameter Ram-jet Engine
A preliminary evaluation was made of three types of combustor configurations in a 48-inch-diameter ram-jet engine to determine the one with the greatest promise of ultimately achieving efficient and stable combustion at low fuel-air rations and low combustor-inlet pressure. The combustor configurations evaluated include (1) a can-piloted configuration using a gutter-type flame holder with can-type pilot burners for stability, (2) an annular-piloted configuration using a gutter-type flame holder with an annular pilot burner to provide stability and to serve as a flow divider for confined fuel-air mixing, and (3) a can-type configuration using a flow divider for confined fuel-air mixing. No modifications were made to optimize the performance of any configuration. On the basis of this preliminary evaluation at an inlet-air temperature of about 990 degrees R, the annular-piloted combustor configuration appeared to have the greatest promise of permitting combustion efficiencies in excess of 0.90 at low fuel-air ratio with combustor-inlet pressures as low as 700 pounds per square foot absolute.
COMBUSTION - RAM-JET ENGINES↗
DEVELOPMENT WORK ON PLASMA ARC JET ENGINES
Open-cycle thermodynamics, nozzle fluid dynamics and heat transfer for plasma arc jet engines
PLASMA JET↗
Perforations in jet engine supersonic inlet increase shock stability
Modification of a conventional jet engine internal compression supersonic inlet results in increased shock stability and thus, engine instantaneous response to changes in inlet air properties. This technique provides a large amount of bleed near the maximum pressure recovery at the expense of minor bleed flow during critical operation.
Keppler, C. R.↗
Design of floated shoe close clearance seals for supersonic jet engine compressors.
Floated shoe close running air seals for supersonic jet engine compressors, discussing axial and radial seals design
Cheng, H.↗
Alternatives for jet engine control
The technical progress of researches on alternatives for jet engine control, is reported. The principal new activities involved the initial testing of an input design method for choosing the inputs to a non-linear system to aid the approximation of its tensor parameters, and the beginning of order reduction studies designed to remove unnecessary monomials from tensor models.
Sain, M. K.↗
Alternatives for jet engine control
The technical progress of researches on alternatives for jet engine control is reported. Extensive numerical testing is included. It is indicated that optimal inputs contribute significantly to the process of calculating tensor approximations for nonlinear systems, and that the resulting approximations may be order-reduced in a systematic way.
Sain, M. K.↗
Jet-Engine Exhaust Nozzle With Thrust-Directing Flaps
Convergent/divergent jet-engine exhaust nozzle has cruciform divergent passage containing flaps that move to deflect flow of exhaust in either or both planes perpendicular to main fore-and-aft axis of undeflected flow. Prototype of thrust-vector-control nozzles installed in advanced, high-performance airplanes to provide large pitching (usually, vertical) and yawing (usually, horizontal) attitude-control forces independent of attitude-control forces produced by usual aerodynamic control surfaces.
Wing, David J.↗
Alternative methods for the design of jet engine control systems
Various alternatives to linear quadratic design methods for jet engine control systems are discussed. The main alternatives are classified into two broad categories: nonlinear global mathematical programming methods and linear local multivariable frequency domain methods. Specific studies within these categories include model reduction, the eigenvalue locus method, the inverse Nyquist method, polynomial design, dynamic programming, and conjugate gradient approaches.
Sain, M. K.↗
Near Noise Field of a Jet-Engine Exhaust
Aircraft structures located in the near noise field of a jet engine are subjected to extremely high fluctuating pressures that may cause structural fatigue. Studies of such structures have been limited by lack of knowledge of the loadings involved. The acoustic near field produced by the exhaust of a stationary turbojet engine having a high pressure ratio was measured for a single operating condition without burning. The maximum overall sound pressure without afterburning was found to be about 42 pounds per square foot along the jet boundary in the region immediately downstream of the jet-nozzle exit. With afterburning maximum sound pressure was increased by 50 percent. The sound pressures without afterburning were obtained on a constant percentage band width basis in the frequency range from 350 to 700 cps. Cross-correlation measurements with microphones were made for a range of jet velocities at locations along the jet and at a distance from the jet. In general, little change in the correlation curves was found as a function of jet velocity or frequency-band width.
Howes, Walton L↗
Investigation of Flow Conditioners for Compact Jet Engine Simulator Rig Noise Reduction
The design requirements for two new Compact Jet Engine Simulator (CJES) units for upcoming wind tunnel testing lead to the distinct possibility of rig noise contamination. The acoustic and aerodynamic properties of several flow conditioner devices are investigated over a range of operating conditions relevant to the CJES units to mitigate the risk of rig noise. An impinging jet broadband noise source is placed in the upstream plenum of the test facility permitting measurements of not only flow conditioner self-noise, but also noise attenuation characteristics. Several perforated plate and honeycomb samples of high porosity show minimal self-noise but also minimal attenuation capability. Conversely, low porosity perforated plate and sintered wire mesh conditioners exhibit noticeable attenuation but also unacceptable self-noise. One fine wire mesh sample (DP450661) shows minimal selfnoise and reasonable attenuation, particularly when combined in series with a 15.6 percent open area (POA) perforated plate upstream. This configuration is the preferred flow conditioner system for the CJES, providing up to 20 dB of broadband attenuation capability with minimal self-noise.
Doty, Michael J.↗
Validation of the gas generator method of calculating jet-engine thrust and evaluation of XB-70-1 airplane engine performance at ground static conditions
Validating gas generator method of calculating jet engine thrust, and evaluation of XB-70-1 engine performance at ground static conditions
Arnaiz, H. H.↗
Smoke emission from jet engines
Combustor design for minimum exhaust smoke emission from aircraft gas turbine jet engines, considering air pollution
Heywood, J. B.↗
Altitude-test-chamber Investigation of Performance of a 28-inch Ram-jet Engine I : Combustion and Operational Performance of Four Combustion-chamber Configurations
An altitude-test-chamber investigation of a 28-inch-diameter ram-jet engine at a simulated flight Mach number of approximately 2.0 for altitudes of 40,000 to 50,000 feet was conducted at the NACA Lewis laboratory. Three different flame holders, varying in the number and size of the annular gutters, in conjunction with several fuel-injection systems were investigated. The combustion efficiency for the flame-holder fuel-injection system that provided the best over-all operational fuel-air-ratio range (0.03 to 0.075) was over 0.9 at a fuel-air ratio of about 0.065 for the altitude range investigated.
MISSILES, SPECIFIC TYPES↗
Starting characteristics and combustion performance of magnesium slurry in 6.5-inch-diameter ram-jet engine mounted in connected-pipe facility
The starting characteristics and combustion performance of slurry type fuels, consisting of 50 percent magnesium powder in a hydrocarbon carrier, have been investigated in a flight-type, 6.5-inch-diameter ram-jet engine in a connected-pipe facility. Quick, dependable starting of the engine was obtained by the use of a disk which blocked part of the combustor area downstream of the flame holder. Acceptable performance was achieved with a short fuel-air mixing length by the development of a fuel-distribution control sleeve.
COMBUSTION - RAM-JET ENGINES↗
Steady-state and dynamic analysis of a jet engine, gas lubricated shaft seal
Dynamic response of a gas-lubricated, jet-engine main shaft seal was analytically established as a function of collar misalignment and secondary seal friction. Response was obtained by a forward integration-in-time (time-transient) scheme, which traces a time history of seal motions in all its degrees of freedom. Results were summarized in the form of a seal tracking map which indicated regions of acceptable collar misalignments and secondary seal friction. Methodology, results and interpretations are comprehensively described.
Shapiro, W.↗
Applications of active adaptive noise control to jet engines
During phase 2 research on the application of active noise control to jet engines, the development of multiple-input/multiple-output (MIMO) active adaptive noise control algorithms and acoustic/controls models for turbofan engines were considered. Specific goals for this research phase included: (1) implementation of a MIMO adaptive minimum variance active noise controller; and (2) turbofan engine model development. A minimum variance control law for adaptive active noise control has been developed, simulated, and implemented for single-input/single-output (SISO) systems. Since acoustic systems tend to be distributed, multiple sensors, and actuators are more appropriate. As such, the SISO minimum variance controller was extended to the MIMO case. Simulation and experimental results are presented. A state-space model of a simplified gas turbine engine is developed using the bond graph technique. The model retains important system behavior, yet is of low enough order to be useful for controller design. Expansion of the model to include multiple stages and spools is also discussed.
Shoureshi, Rahmat↗