Search NASA⌕ Search

SEARCH · Search NASA

Results for “LEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Surface structures of In-Pd intermetallic compounds. I. Experimental study of In thin films on Pd(111) and alloy formation

A combination of experimental methods was used to study the structure of In thin films deposited on the Pd(111) surface and the alloying behavior. X-ray photoelectron spectroscopy (XPS), low-energy electron diffraction (LEED), and scanning tunneling microscopy results indicate that surface alloying takes place at room temperature. Below 2 monolayer equivalents (MLEs), the LEED patterns show the formation of three rotational domains of InPd(110) of poor structural quality on top of the Pd(111) substrate. Both core-levels and valence band XPS spectra show that the surface alloy does not yet exhibit the electronic structure characteristic of the 1:1 intermetallic compound under these conditions. Annealing the 1 MLE thin film up to 690 K yields to a transition from a multilayer InPd near-surface intermetallic phase to a monolayer-like surface alloy exhibiting a well ordered (√(3)×√(3)) R30{sup ∘} superstructure and an estimated composition close to In{sub 2}Pd{sub 3}. Annealing above 690 K leads to further In depletion and a (1 × 1) pattern is recovered. The (√(3)×√(3)) R30{sup ∘} superstructure is not observed for thicker films. Successive annealing of the 2 MLE thin film leads the progressive disappearance of the InPd diffraction spots till a sharp (1 × 1) pattern is recovered above 690 K. In the high coverage regime (from 4 to 35 MLE), the formation of three rotational domains of a bcc-In{sub 7}Pd{sub 3} compound with (110) orientation is observed. This In-rich phase probably grows on top of interfacial InPd(110) domains and is metastable. It transforms into a pure InPd(110) near-surface intermetallic phase in a temperature range between 500 and 600 K depending on the initial coverage. At this stage, the surface alloy exhibits core-level chemical shifts and valence band (VB) spectra identical to those of the 1:1 InPd intermetallic compound and resembling Cu-like density of states. Annealing at higher temperatures yields to a decrease of the In concentration in the near-surface region to about 20 at.% and a (1 × 1) LEED pattern is recovered.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Non-destructive assessment of the polarity of GaN nanowire ensembles using low-energy electron diffraction and x-ray photoelectron diffraction

We investigate GaN nanowire ensembles spontaneously formed in plasma-assisted molecular beam epitaxy by non-destructive low-energy electron diffraction (LEED) and x-ray photoelectron diffraction (XPD). We show that GaN nanowire ensembles prepared on AlN-buffered 6H-SiC(0001{sup ¯}) substrates with well-defined N polarity exhibit similar LEED intensity-voltage curves and angular distribution of photo-emitted electrons as N-polar free-standing GaN layers. Therefore, as in the case of GaN layers, LEED and XPD are found to be suitable techniques to assess the polarity of GaN nanowire ensembles on a macroscopic scale. The analysis of GaN nanowire ensembles prepared on bare Si(111) allows us to conclude that, on this non-polar substrate, the majority of nanowires is also N-polar.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Incommensurate growth of Co thin film on close-packed Ag(111) surface

Growth of ultrathin Co layers on close-packed Ag(111)were investigated by means of Low Energy Electron Diffraction (LEED), X-ray Photoelectron Spectroscopy (XPS) and Angle-resolved Photoemission Spectroscopy(ARPES) techniques. The close-packed hexagonal face of Co(0001), exhibits a lattice misfit about 13% with Ag(111) surface which manipulates the growth to be incommensurate up to a certain thickness. The strain field causes aperiodic height undulation in the sub-angstrom regime of the film which was confirmed by p(1 × 1) LEED pattern along with a 6-fold moiré reconstruction pattern in the lower film thickness (up to ∼2ML). The evolution of the LEED pattern was studied with increasing film coverage. Lattice strain was measured with respect to the relative positions of these double spots as a functionof film thickness. Almost a constant strain (∼13%) in the full range of film thickness explains the moiré pattern formation in order to stabilize the incommensurate growth. For higher film coverages, an epitaxial well-ordered commensurate growth was observed. Core level and valance band electronic structures of these films were studied by XPS and ARPES techniques.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Structural and electronic properties of polar MnO ultrathin film grown on Ag(111)

Surface electronic structure of ultrathin polar MnO film was studied by Low-energy Electron Diffraction (LEED) and Photoemission Spectroscopic (PES) techniques. Epitaxial monolayer to facet formation with increasing film thickness has been observed by LEED. Our LEED result shows p(2x2) surface reconstruction along with facet formation, stabilize the polar MnO(111) surface. The core levels and the valence band electronic structure of MnO films have been studied as a function of film thickness using X-ray and ultraviolet photoelectron spectroscopy techniques.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Vibrational spectra of CO adsorbed on oxide thin films: A tool to probe the surface defects and phase changes of oxide thin films

Thin films of iron oxide were grown on Pt(111) single crystals using cycles of physical vapor deposition of iron followed by oxidative annealing in an ultrahigh vacuum apparatus. Two procedures were utilized for film growth of ∼15–30 ML thick films, where both procedures involved sequential deposition+oxidation cycles. In procedure 1, the iron oxide film was fully grown via sequential deposition+oxidation cycles, and then the fully grown film was exposed to a CO flux equivalent to 8 × 10{sup −7} millibars, and a vibrational spectrum of adsorbed CO was obtained using infrared reflection-absorption spectroscopy. The vibrational spectra of adsorbed CO from multiple preparations using procedure 1 show changes in the film termination structure and/or chemical nature of the surface defects—some of which are correlated with another phase that forms (“phase B”), even before enough of phase B has formed to be easily detected using low energy electron diffraction (LEED). During procedure 2, CO vibrational spectra were obtained between deposition+oxidation cycles, and these spectra show that the film termination structure and/or chemical nature of the surface defects changed as a function of sequential deposition+oxidation cycles. The authors conclude that measurement of vibrational spectra of adsorbed CO on oxide thin films provides a sensitive tool to probe chemical changes of defects on the surface and can thus complement LEED techniques by probing changes not visible by LEED. Increased use of vibrational spectra of adsorbed CO on thin films would enable better comparisons between films grown with different procedures and by different groups.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Metal thin film growth on multimetallic surfaces: From quaternary metallic glass to binary crystal

The work presented in this thesis mainly focuses on the nucleation and growth of metal thin films on multimetallic surfaces. First, we have investigated the Ag film growth on a bulk metallic glass surface. Next, we have examined the coarsening and decay of bilayer Ag islands on NiAl(110) surface. Third, we have investigated the Ag film growth on NiAl(110) surface using low-energy electron diffraction (LEED). At last, we have reported our investigation on the epitaxial growth of Ni on NiAl(110) surface. Some general conclusions can be drawn as follows. First, Ag, a bulk-crystalline material, initially forms a disordered wetting layer up to 4-5 monolayers on Zr-Ni-Cu-Al metallic glass. Above this coverage, crystalline 3D clusters grow, in parallel with the flatter regions. The cluster density increases with decreasing temperature, indicating that the conditions of island nucleation are far-from-equilibrium. Within a simple model where clusters nucleate whenever two mobile Ag adatoms meet, the temperature-dependence of cluster density yields a (reasonable) upper limit for the value of the Ag diffusion barrier on top of the Ag wetting layer of 0.32 eV. Overall, this prototypical study suggests that it is possible to grow films of a bulk-crystalline metal that adopt the amorphous character of a glassy metal substrate, if film thickness is sufficiently low. Next, the first study of coarsening and decay of bilayer islands has been presented. The system was Ag on NiAl(110) in the temperature range from 185 K to 250 K. The coarsening behavior, has some similarities to that seen in the Ag(110) homoepitaxial system studied by Morgenstern and co-workers. At 185 K and 205 K, coarsening of Ag islands follows a Smoluchowski ripening pathway. At 205 K and 250 K, the terrace diffusion limited Ostwald ripening dominants. The experimental observed temperature for the transition from SR to OR is 205 K. The SR exhibits anisotropic island diffusion and the OR exhibits 1D decay of island length while keeping the corresponding island width constant. Third, LEED indicates that, up to about 6 BL (12 ML), the Ag film adopts the (110) structure on lattice matched NiAl(110) surface, supporting the previous assignment based upon island heights measured in STM. Starting at 4.5 to 6 BL, (111) diffraction pattern is detected. This is also in agreement with previous STM study. Careful examinations of the LEED patterns reveal the slight difference in lattice constants between bulk Ag and bulk NiAl. At last, we performed STM studies of Ni deposition on NiAl(110) in the temperature range from 200 K to 400 K. Ni forms 'dense' Ni(100)-like islands on NiAl(110) with a zig-zag shaped stripe feature which is probably due to strain relief. DFT analysis provides insights into the island growth shapes, which are rationalized by the thermodynamics and kinetics of the film growth process. For thick Ni films (coverage exceeding 6 ML), a Ni(111)-like structure developed. Traditional MF theory is applied to analyze island density at 200 K. Deviation from homogeneous nucleation behavior for island size distribution and island density reveals the presence of heterogeneous nucleation mediated by the Ni antisite point defects on NiAl(110) surface.

36 MATERIALS SCIENCE↗

Energy Modeling for the Artisan Food Center

The Artisan Food Center is a 6912 sq.ft food processing plant located in Dayton, Washington. PNNL was contacted by Strecker Engineering to assist with the building’s energy analysis as a part of the project’s U.S. Green Building Council’s Leadership in Energy and Environmental Design (LEED) submittal requirements. The project is aiming for LEED Silver certification, one of the prerequisites to which is a whole building energy model to demonstrate compliance with American Society of Heating Refrigeration and Air Conditioning Engineers (ASHRAE) 90.1 2007 Appendix G, Performance Rating Method. The building incorporates a number of energy efficiency measures as part of its design and the energy analysis aimed at providing Strecker Engineering with the know-how of developing an energy model for the project as well as an estimate of energy savings of the proposed design over the baseline design, which could be used to document points in the LEED documentation. This report documents the ASHRAE 90.1 2007 baseline model design, the proposed model design, the modeling assumptions and procedures as well as the energy savings results in order to inform the Strecker Engineering team on a possible whole building energy model.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Renewable Energy at NASA's Johnson Space Center

NASA's Johnson Space Center has implemented a great number of renewable energy systems. Renewable energy systems are necessary to research and implement if we humans are expected to continue to grow and thrive on this planet. These systems generate energy using renewable sources - water, wind, sun - things that we will not run out of. Johnson Space Center is helping to pave the way by installing and studying various renewable energy systems. The objective of this report will be to examine the completed renewable energy projects at NASA's Johnson Space Center for a time span of ten years, beginning in 2003 and ending in early 2014. This report will analyze the success of each project based on actual vs. projected savings and actual vs. projected efficiency. Additionally, both positive and negative experiences are documented so that lessons may be learned from past experiences. NASA is incorporating renewable energy wherever it can, including into buildings. According to the 2012 JSC Annual Sustainability Report, there are 321,660 square feet of green building space on JSC's campus. The two projects discussed here are major contributors to that statistic. These buildings were designed to meet various Leadership in Energy and Environmental Design (LEED) Certification criteria. LEED Certified buildings use 30 to 50 percent less energy and water compared to non-LEED buildings. The objectives of this project were to examine data from the renewable energy systems in two of the green buildings onsite - Building 12 and Building 20. In Building 12, data was examined from the solar photovoltaic arrays. In Building 20, data was examined from the solar water heater system. By examining the data from the two buildings, it could be determined if the renewable energy systems are operating efficiently. Objectives In Building 12, the data from the solar photovoltaic arrays shows that the system is continuously collecting energy from the sun, as shown by the graph below. Building 12 has two solar inverters, located on the second floor, that collected the data from the solar photovoltaic arrays. The data displayed here is the total energy produced by the system. These are cumulative amounts, so the last point on the graph shows all of the energy collected from the system since the start of its operation. The data shown here was manually collected from the solar inverters. However, the data is also automatically recorded through EBI. Through analysis of both sets of data it was determined that the EBI data was faulty. For example, from the manually collected data it can be determined that a total of 73 kWh of energy was collected between the dates of 1/16/2014 – 1/22/2014. The EBI data reports that approximately 17800 kWh of energy was collected during the same time frame. Not only does this exceed the time frame examined, but it also exceeds the total energy collected from the start of collection as recorded from the inverters. This leads to the belief that there is a malfunction with the automatic recording of the energy. In Building 20, data was examined from the solar water heater dating back many months and found that the pump for the solar water heater system was not operating properly, as exhibited in the graph shown below. The pump operates on a solar energy system, meaning that it collects energy throughout the day from the sun. Because of this, the system would stop operating shortly after the sun set because of a lack of sunlight. At that point, the graph should show a zero flow rate, but as exhibited in the graph below, that is not the case. It is clearly shown that the pump is continuously operating, even during the night. It was also observed that the majority of the time the pump would not turn on at all, despite good weather conditions. This led to the conclusion that the pump is malfunctioning, and needs to be examined and fixed.

McDowall, Lindsay↗

Impact of a Mixed Oxide’s Surface Composition and Structure on Its Adsorptive Properties: Case of the (Fe,Cr) 3 O 4 (111) Termination of the α-(Fe,Cr) 2 O 3 (0001) Surface

Characterization of an α-(Fe 0.75 ,Cr 0.25 ) 2 O 3 (0001) mixed oxide single crystal surface was conducted using x-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS), low energy electron diffraction (LEED) and temperature programmed desorption (TPD). After sputter/anneal cleaning in ultra-high vacuum (UHV), the mixed oxide surface became terminated with a magnetite-(111) structure based on the presence of (2x2) spots in LEED and Fe 2+ in XPS. The composition of the surface was close to that of M 3 O 4 based on XPS, with the metal (M) content of Fe 2+/3+ and Cr 3+ being close to 1.4:1, despite the fact that the film’s bulk was 3:1 with respect to the metal cations. The enrichment of the surface with Cr was not altered by high temperature oxidation in UHV, but could be returned to that of the bulk film composition by exposure to the ambient. Adsorption of various probe molecules (NO, O 2 , CO 2 and H 2 O) was used to identify the active cation sites present in the (Fe,Cr) 3 O 4 (111) terminated surface. Although XPS and SIMS both indicated that the near-surface region was enriched in Cr 3+ , no adsorption states typically associated with Cr 3+ sites on α-Cr 2 O 3 single crystal surfaces were detected. Instead, the TPD behaviors of O 2 and CO 2 pointed toward the main active sites being Fe 2+ and Fe 3+ , with O 2 preferentially adsorbing at the former and CO 2 at the latter. NO was observed to bind at both Fe 2+ and Fe 3+ sites, and H 2 O TPD looked nearly identical to that for H 2 O on the Fe 3 O 4 (111) surface. Competition for adsorption sites between coadsorbed combinations of CO 2 , O 2 , H 2 O and NO corroborated these assignments. These results indicate that the surface composition of a mixed oxide can vary significantly from its bulk composition depending on the treatment conditions. Even then, the surface composition does not necessarily provide direct insight into the active adsorption sites. In the case of the (Fe,Cr) 3 O 4 (111) termination of the α-(Fe 0.75 ,Cr 0.25 ) 2 O 3 (0001) surface, Cr 3+ cations in the near-surface region appear to be fully coordinated and unavailable for adsorbing molecules. The authors thank Drs. Sara Chamberlin and Scott Chambers for supplying the film used in this work. This work was supported by the US Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. Pacific Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle. The research was performed using EMSL, a national scientific user facility sponsored by the Department of Energy's Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory.

adsorption↗

Metallic atomically-thin layered silicon epitaxially grown on silicene/ZrB 2

Using low energy electron diffraction (LEED) and scanning tunnelling microscopy (STM), we observe a new two-dimensional (2D) silicon crystal that is formed by depositing additional Si atoms onto spontaneously-formed epitaxial silicene on a ZrB2 thin film. From scanning tunnelling spectroscopy (STS) studies, we find that this atomically-thin layered silicon has distinctly different electronic properties. Angle resolved photoelectron spectroscopy (ARPES) reveals that, in sharp contrast to epitaxial silicene, the layered silicon exhibits significantly enhanced density of states at the Fermi level resulting from newly formed metallic bands. The 2D growth of this material could allow for direct contacting to the silicene surface and demonstrates the dramatic changes in electronic structure that can occur by the addition of even a single monolayer amount of material in 2D systems.

36 MATERIALS SCIENCE↗

INL High-Performance and Sustainable Building Strategy

High-performance buildings are reliable, cost-effective, and sustainable structures that minimize energy and water use, reduce solid waste and pollutant emissions, and limit the depletion of natural resources while also providing a thermally and visually comfortable working environment that increases productivity for building occupants. As Idaho National Laboratory (INL) is the nation’s premier nuclear energy research laboratory, the physical infrastructure requires continual updating and re-purposing to help accomplish that mission. INL’s infrastructure must incorporate high-performance sustainable design features to be fiscally responsible and reflect an image of innovation to the public and prospective employees. INL is a large consumer of energy with annual energy costs exceeding $9M. In the current fiscal reality and with energy costs constantly increasing, this High-Performance and Sustainable Building Strategy will help engineering and construction project teams design facilities that are sustainable and will help to reduce life-cycle operating costs while providing INL employees with a safe and healthy working environment. With these goals in mind, the recommendations described in this document are intended to form INL’s foundation for sustainable and high-performance building standards. This strategy incorporates the latest federal and Department of Energy (DOE) orders and directives including Executive Order (EO) 13834, “Efficient Federal Operations” and its associated implementing instructions, DOE Order 436.1, “Departmental Sustainability,” the DOE Sustainability Report and Implementation Plan (SRIP), the INL Site Sustainability Plan (SSP), and Code of Federal Regulations (CFR). This document identifies the requirements of the Guiding Principles for Sustainable Federal Buildings (Guiding Principles) and briefly highlights the requirements of Leadership in Energy and Environmental Design (LEED®) Gold certification. LEED Gold certification, while optional, can be used to meet many of the requirements of the Guiding Principles.

13834↗

INL High-Performance and Sustainable Building Strategy

High-performance buildings are reliable, cost effective, and sustainable structures that minimize energy and water use, reduce solid waste and pollutant emissions, and limit the depletion of natural resources. High-performance buildings also provide a thermally and visually comfortable working environment that increases productivity for building occupants. As Idaho National Laboratory (INL) is the nation’s premier nuclear energy research laboratory, the physical infrastructure requires continual updating and repurposing to help accomplish that mission. INL’s infrastructure must incorporate high-performance sustainable design features to be fiscally responsible and reflect an image of innovation to the public and prospective employees. INL is a large consumer of energy with annual energy costs exceeding $16M. This High-Performance and Sustainable Building Strategy will help engineering and construction project teams design sustainable facilities, reduce life cycle operating costs, and support the INL net-zero plan while providing INL employees with a safe and healthy working environment. With these goals in mind, the recommendations described in this document are intended to form INL’s foundation for sustainable and high-performance building standards. This strategy incorporates the latest federal and Department of Energy (DOE) orders and directives, including DOE Order 436.1A, “Departmental Sustainability,” the DOE Sustainability Plan (SP), the INL Site Sustainability Plan (SSP), and Code of Federal Regulations (CFR). This document identifies the requirements of the “Guiding Principles for Sustainable Federal Buildings” (Guiding Principles) and briefly highlights the Leadership in Energy and Environmental Design (LEED) Gold certification. LEED Gold certification can be used to meet many of the requirements of the Guiding Principles.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

From Tragedy to Triumph: Rebuilding Greensburg, Kansas To Be a 100% Renewable Energy City; Preprint

On May 4, 2007, Greensburg, Kansas, was hit by a 1.7-mile wide tornado with 200 mph-plus wind speeds. This tornado destroyed or severely damaged 90% of Greensburg?s structures. We discuss the progress made in rebuilding Greensburg, with a focus on the built environment and on meeting Greensburg?s goal of 100% renewable energy, 100% of the time. We also discuss key disaster recovery efforts thatenabled Greensburg to reach this goal. Key strategies included a Sustainable Comprehensive Master Plan, an ordinance resolving that city-owned buildings achieve LEED Platinum and 42% energy savings, a strong focus on rebuilding 'right' with an integrated design process, attracting significant and sustained technical experts and national media attention, and linking renewable and energyefficiency technologies to business development. After three years, more than half the homes that have been rebuilt are rated at an average of 40% energy savings. All significant commercial buildings, including the school, hospital, banks, courthouse, and retail buildings, have been rebuilt to LEED Gold and Platinum standards and exceed 40% savings, with many exceeding 50% savings. Greensburgrecently constructed a 12.5-MW community wind farm to provide all the remaining energy needed for its energy-efficient buildings and homes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

A critical review of environmental assessment tools for sustainable urban design

Cities are responsible for the depletion of natural resources and agricultural lands, and 70% of global CO{sub 2} emissions. There are significant risks to cities from the impacts of climate change in addition to existing vulnerabilities, primarily because of rapid urbanization. Urban design and development are generally considered as the instrument to shape the future of the city and they determine the pattern of a city's resource usage and resilience to change, from climate or otherwise. Cities are inherently dynamic and require the participation and engagement of their diverse stakeholders for the effective management of change, which enables wider stakeholder involvement and buy-in at various stages of the development process. Sustainability assessment of urban design and development is increasingly being seen as indispensable for informed decision-making. A sustainability assessment tool also acts as a driver for the uptake of sustainable pathways by recognizing excellence through their rating system and by creating a market demand for sustainable products and processes. This research reviews six widely used sustainability assessment tools for urban design and development: BREEAM Communities, LEED-ND, CASBEE-UD, SBTool{sup PT}–UP, Pearl Community Rating System (PCRS) and GSAS/QSAS, to identify, compare and contrast the aim, structure, assessment methodology, scoring, weighting and suitability for application in different geographical contexts. Strengths and weaknesses of each tool are critically discussed. The study highlights the disparity in local and international contexts for global sustainability assessment tools. Despite their similarities in aim on environmental aspects, differences exist in the relative importance and share of mandatory vs optional indicators in both environmental and social dimensions. PCRS and GSAS/QSAS are new incarnations, but have widely varying shares of mandatory indicators, at 45.4% and 11.36% respectively, compared to 30% in BREEAM Community. Considerations of economic and cultural aspects are only marginal in the reviewed sustainability assessment tools. However, the newly developed sustainability assessment tools such as GSAS/QSAS and PCRS diverge from their predecessors in their consideration of cultural aspects. - Highlights: • Reviews six urban sustainability assessment methods: LEED-ND, BREEAM Communities, CASBEE-UD, SBTool{sup PT}-UP, PCRS, GSAS/QSAS. • Reviewed methods are biased more towards the environmental, followed by social and economic dimensions of sustainability. • Water issues are highlighted in the Middle East but natural hazards are emphasized only in CASBEE and BREEAM Communities. • SBTool{sup PT}-UP, the most recent of the groups puts more weight (7.32%) on cultural aspects. • Share of mandatory indicators is highest (45.4%) in the Pearl Community Rating System (PCRS)

54 ENVIRONMENTAL SCIENCES↗

Certification systems for sustainable neighbourhoods: What do they really certify?

Certification systems for sustainable neighbourhoods started to emerge around a decade ago. This study analysed the content, structure, weighting and indicators of two established certification systems for sustainable urban development – BREEAM Communities and LEED for Neighborhood Development. Several limitations of these systems were identified: both have a bias for procedure and feature indicators over indicators that assess actual performance; performance demands are set according to a relative understanding of sustainable development; the focus is on internal sustainability, while upstream and downstream impacts of construction are disregarded; the number and distribution of mandatory issues do not cover essential sustainability aspects; and the disproportionately large number of non-mandatory issues makes benchmarking difficult and signals that sustainability aspects are exchangeable. Altogether, this means that an area can be certified without being sustainable. Moreover, the lack of continuous development of certification requirements in the systems means that they risk exerting a conservative effect on urban development, rather than pushing it forward. - Highlights: • BREEAM-C and LEED-ND were analysed in terms of content and structure. • Specific attention was given to the type of indicators used for showing compliance. • In both systems procedure and feature indicators dominate over performance indicators. • Several other limitations of these certification systems were also identified. • Altogether the limitations imply that a certificate does not warrant sustainability.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Oxygen Plasma Activation of Cr(CO)(6) on α-Fe2O3(0001)

The chemistry of Cr(CO)6 on the Fe3O4(111) surface termination of α-Fe2O3(0001) was explored using temperature programmed desorption (TPD), Auger electron spectroscopy (AES), static secondary ion mass spectrometry (SSIMS) and low energy electron diffraction (LEED) both with and without activation from an oxygen plasma source. No thermal decomposition of Cr(CO)6 was detected on the surface in the absence of O2 plasma treatment, with first layer molecules desorbing in TPD at 215 K from a close-packed overlayer. The interaction of first layer Cr(CO)6 with the Fe3O4(111)-termination was weak, desorbing only ~30 K above the leading edge of the multilayer state. Activation of multilayer coverages of Cr(CO)6 with the O2 plasma source at 100K resulted in complete conversion of the outer Cr(CO)6 layers, presumably to a disordered Cr oxide film, with Cr(CO)6 molecules near the surface left unaffected. Absence of CO or CO2 desorption states suggests that all carbonyl ligands are liberated for each Cr(CO)6 molecule activated by the plasma. AES and SSIMS both show that O2 plasma activation of Cr(CO)6 results in a carbon-free surface (after desorption of unreacted Cr(CO)6). LEED, however, shows that the Cr oxide film is disordered at 600 K and likely O-terminated based on subsequent water TPD. Attempts to order the film at temperatures above 650 K results in dissolution of Cr into the α-Fe2O3(0001) crystal based on SSIMS, an observation that is linked to the Fe3O4(111) termination of the surface and not to the properties of α-Cr2O3/α-Fe2O3 corundum interfaces. Nevertheless, this study shows that O2 plasma activation of Cr(CO)6 is an effect means of depositing Cr oxide films on surface without accompanying carbon contamination.

36 MATERIALS SCIENCE↗

Oxygen-induced nano-faceting of Re( 11 2 ¯ 1 )

We report results from a detailed study of oxygen-induced faceting of Re(112¯1) using low energy electron diffraction (LEED). Depending on conditions for reaction with oxygen, the initially planar Re(112¯1) surface evolves sequentially to form zigzag chains consisting of (011¯0) and (101¯0) facets that coexist with stepped (112¯1) plateaus; three-sided pyramids exposing (011¯0), (101¯0) and (336¯4) facets; a faceted surface with five facets including (011¯0), (101¯0), (112¯2)-(2 × 1), (011¯1)-(2 × 1) and (101¯1)-(2 × 1); and four-sided pyramids exposing {011¯0} and {011¯1}-(2 × 1) facets. We have observed reversible morphological transitions between the faceted surfaces and discovered that each intermediate facet in the evolutionary chain contains microscopic structural elements of the preceding and following facets, which may provide a natural explanation for the microscopic mass transport pathways in the morphological evolution. Lastly, scanning tunneling microscopy (STM) data confirm the morphology of faceted surfaces and give complementary information to LEED results.

36 MATERIALS SCIENCE↗

The Surface Chemistry of Methanol on Cu 3 Pd(111): Effects of Metal Alloying and Reaction with Hydrogen

Synchrotron-based ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) was used to study the adsorption and surface chemistry of methanol on a Cu 3 Pd(111) model surface. The composition and morphological properties of the pristine Cu 3 Pd(111) substrate were analyzed using a combination of low-energy electron diffraction (LEED), scanning tunneling microscopy (STM), and low-energy ion scattering (LEIS). The results of ion scattering showed segregation of Pd toward the surface, with a Pd/Cu ratio close to 0.5, a larger value than the ratio of 0.33 expected for a Cu 3 Pd bimetallic structure. The surface of the alloy exhibited a good LEED pattern with three-fold long-range periodicities. In STM, clusters of palladium with hexagonal arrays and Pd- Pd distances of 2.7-2.8 Å were detected. Bonding to copper perturbed the electronic properties of the atoms in the Pd clusters, shifting their 4d states toward higher binding energy with respect to the Fermi level. Further, the valence band spectrum of Cu 3 Pd(111) exhibited a line shape that was very different from those displayed by Cu(111) or Pd(111). At low pressures, the adsorption of methanol on Cu 3 Pd(111) at 300 K mainly produced CH 3 O, CO and CH x species. AP-XPS showed that most Pd atoms in the surface of the Cu 3 Pd(111) alloy interacted with the decomposition products of methanol. No significant changes were observed in the core levels of copper upon the adsorption and dissociation of methanol, suggesting that the molecule mainly interacted with Pd sites of the alloy. Reaction with hydrogen led to fast removal of CH x , C and PdC x species from Cu 3 Pd(111) at moderate (< 450 K) temperatures and prevented a CH x → C transformation. If the stability of adsorbed CH 3 O is used as a descriptor for the hydrogenation of CO 2 to methanol, Cu 3 Pd should be a much better catalyst than monometallic palladium. This may be a consequence of electronic and ensemble effects in the alloy that moderate the reactivity of Pd sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗