Search NASA⌕ Search

SEARCH · Search NASA

Results for “LIGHT PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Eliminating Signal Bias Caused by Vacuum System Backstreaming in the Diagnostic Residual Gas Analyzer of ITER

In fusion neutral gas analysis, such as with the Diagnostic Residual Gas Analyzer (DRGA) for ITER, the primary measurement range of interest comprises the low-amu species (1 to 6), especially deuterium and helium. The challenge in successfully obtaining accurate measurements is two-fold. First, the sensitivity of the method must be sufficient to resolve trace amounts accurately; typically, one percent or less. Second, the gas signal from the fusion processes must be free of bias caused by the latent presence (from system outgassing and/or vacuum backstreaming) of these gases to enable accurate interpretation of the measured signal. This latter criterion can be problematic for the lightest gases since there is a propensity for some fraction of the pumped gas load to undergo a phenomenon known as backstreaming. This behavior is manifested in pumping systems for gas properties related to relative atomic weight (lightest) and size (smallest). Backstreaming results in a significant amount of the pumped gas undertaking a reverse flow and re-entering the measurement region; thus, contaminating the forward, real-time measurement. To fully eliminate this adverse effect, a conductance-limiting device – or orifice – has been installed in the high-vacuum pumping system of the present ITER DRGA prototype. The system was already equipped with a secondary turbomolecular pump (TMP), but with limited effectiveness against backstreaming in the inter-pump volume (IPV). This orifice is placed within the suction inlet coupling of the secondary TMP, which is downstream of the IPV. Its objective is to eliminate the backstreaming phenomenon by increasing the back pressure in the IPV. However, the orifice sizing must take into consideration other factors, such as the diagnostic measurement objectives. For example, in the ITER DRGA, one of the measurement requirements is a dynamic response time of ~1s. Fortunately, an added benefit of the pumping restriction created by the orifice is that the upstream pressure increase is beneficial for the DRGA’s optical gas analysis (OGA) sensors. These sensors are attached to the IPV in the present design. The glow discharges, when used as an OGA light source, will typically have a brighter light emission with increasing plasma cell pressure. In addition to the fusion machine research sector, there are other potential applications of this pumping technique where the monitoring of lighter gas concentrations is essential, such as the photolithography process for the semiconductor fabrication of integrated circuits. This presentation will describe the vacuum system used to demonstrate a process to eliminate backstreaming as well as show test results to verify the accomplishment of this critical objective.

Marcus, Chris↗
DOE OSTI2021

Cryogenic Carbon Capture™ Technoeconomic Analysis

The Cryogenic Carbon Capture™ (CCC) process significantly decreases cost and energy demands for CO 2 separation and pressurization to 150 bar compared to alternatives. The process is a post-combustion technology that cools CO 2 -laden flue gas to desublimation temperatures (-100 to -135 °C), separates solid CO 2 —that forms from the flue gas—from the light gases, uses the cold products to cool incoming gases in a recuperative heat exchanger, compresses the solid/liquid CO 2 to final pressures (100–200 bar), and delivers a compressed CO 2 stream separated from an atmospheric pressure light-gas stream. The overall energy and economic costs are about 30-50% lower than most competing processes that involve air separation units (ASUs), solvents, or similar technologies. In addition, the CCC process enjoys several ancillary benefits, including (a) it is a minimally invasive Bolton technology, (b) it provides highly efficient removal of most pollutants (Hg, SOx, NO 2 , HCl, etc.), and (c) possible energy storage capacity. This report outlines the process details and economic and energy comparisons relative to other well-documented alternatives. This paper presents the results of a detailed techno-economic comparison of CCC with amine-based systems. The comparison uses identical financial and economic assumptions similar process assumptions as the detailed analyses published by US DOE in the greenfield analysis. Specifically, the comparison assumes power plants that produce the same net output, one equipped with and a second without carbon capture. Separately, the paper compares similar analyses for retrofitting existing systems using typical plant characteristics in the US (initial capital costs have been paid, high plant utilization), though there are no DOE estimates available for direct comparison. Financial and technical assumptions for all comparisons are maintained as close to the DOE reference studies as possible. The results demonstrate about 30-50% lower costs and energy demands for capture from greenfield coal plants. Natural gas plants produce substantially lower CO 2 concentrations which makes the cost of capturing a ton of CO 2 at the same capture rate as the coal plant higher for all processes while the cost of CO 2 capture per unit of power generation is lower. However, CCC maintains about the same absolute energy and cost advantages for NG as for coal compared to amine systems. Finally, the costs of retrofitting a station are compared to those of building a new station with and without capture. The retrofit costs are comparable to (slightly lower than) new plant costs without capture. In all cases operating and capital cost comparisons show that the CCC process can be retrofitted to a variety of plants to cost effectively reduce CO 2 emissions. Further process integration into the upstream processes and unique process features like water recovery, and integrated energy storage bring the effective cost of carbon capture using the CCC process down further and increase its advantages over alternatives. This technoeconomic analysis shows that the CCC process has the potential to the be lowest cost carbon capture technology under development today.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Pressure-stable supported ionic liquid membranes using isoporous supports for evaluating pure- and mixed-gas light paraffin fractionation

Advances in horizontal drilling and hydraulic fracturing have spurred the growth of domestic U.S. energy production. Membranes, typically silicone rubbers, have found utility in shale gas treatment as fuel gas conditioning units to selectively remove C 2 + hydrocarbons at pressures up to 30 bar, producing clean CH 4 for gas engines. However, more selective materials could be beneficial for broader shale gas treatment applications, such as dew point control units. Supported ionic liquid membranes (SILMs) offer a potential opportunity for improving C 3 H 8 /CH 4 selectivity, but they lack pressure-stability. Here, we report C 3 H 8 /CH 4 selective and pressure-stable SILMs using isoporous supports. SILMs with supports that had minimal defects remained stable up to 15 bar of transmembrane pressure. This stability allowed for pure- and mixed-gas testing of the resulting membranes at elevated pressures. Furthermore, these tests revealed that low viscosity ILs (<100 cp) may display mixed-gas permeances and permselectivity nearly identical to pure-gas results. On the other hand, higher viscosity ILs may display increasing permeances and permselectivity with increasing C 3 H 8 fugacity, similar to rubbery polymers. Ultimately, the SILMs demonstrated relatively high pressure-stability due to the isoporous supports and competitive mixed-gas C 3 H 8 /CH 4 permselectivity compared to silicone rubber.

Rosenthal, Justin J. [University of Texas at Austi↗
DOE OSTI2024

Trapping and actively transporting single particles of arbitrary properties in low-pressure rf plasmas with and without a magnetic field

We report the experimental realization of optical trapping and controlled manipulations of single particles of arbitrary properties, e.g., nano- to micrometer in size, transparent spheres to strongly light absorbing nonspherical particles, in low-pressure rf plasmas. First, we show optical trapping and transport of single particles in an unmagnetized rf plasma. Then, we show similar observations in a weakly magnetized rf plasma. This is the first demonstration of actively transporting (pushing and pulling) light-absorbing, nonspherical single particles in plasmas. The result suggests that optically trapped, actively controlled, single plasma dust particles (not limited to those externally sampled spheres) could be an in situ micro-probe for dusty plasma and magnetized dusty plasma diagnostics.

Physics↗
DOE OSTI2020

Pressure-induced phase transition in barium hydride studied with neutron scattering

Barium hydride can undergo a structural phase transition from an orthorhombic phase to a hexagonal phase induced by high temperature or high pressure. This transition causes an immediate increase in the hydrogen diffusion rates by over an order of magnitude, and therefore, understanding the origin and details of such transition is of great interest not only for fundamental reasons but also for improving materials for future applications. In this work, the pressure evolution of the crystal structure was characterized using neutron powder diffraction up to a maximum pressure of 11.3 GPa. The pressure dependence of the unit cell volumes, lattice parameters, atomic sites, and compressibilities were determined for both phases. A structural phase transition occurred over a wide pressure range of P = 1.3 GPa–4.9 GPa. The transition to the higher density hexagonal phase reduced the volume per formula unit of BaD 2 by 13.6%, hence increasing the volumetric storage density. In addition, we investigated the hydrogen diffusion process using high pressure quasi-elastic neutron scattering up to 7.1 GPa. Our results show that the hydrogen mobility increases with pressure in the hexagonal phase. This work sheds light on the structural and dynamical aspects of barium hydride caused by the application of high pressure. Finally, the results may aid in the development of advanced metal hydride systems with increased hydrogen dynamics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Evidence of shock-compressed stishovite above 300 GPa

SiO 2 is one of the most fundamental constituents in planetary bodies, being an essential building block of major mineral phases in the crust and mantle of terrestrial planets (1–10 M E ). Silica at depths greater than 300 km may be present in the form of the rutile-type, high pressure polymorph stishovite (P4 2 /mnm) and its thermodynamic stability is of great interest for understanding the seismic and dynamic structure of planetary interiors. Previous studies on stishovite via static and dynamic (shock) compression techniques are contradictory and the observed differences in the lattice-level response is still not clearly understood. Here, laser-induced shock compression experiments at the LCLS- and SACLA XFEL light-sources elucidate the high-pressure behavior of stishovite on the lattice-level under in situ conditions on the Hugoniot to pressures above 300 GPa. We find stishovite is still (meta-)stable at these conditions, and does not undergo any phase transitions. This contradicts static experiments showing structural transformations to the CaCl 2 , α-PbO 2 and pyrite-type structures. However, rate-limited kinetic hindrance may explain our observations. These results are important to our understanding into the validity of EOS data from nanosecond experiments for geophysical applications.

58 GEOSCIENCES↗
DOE OSTI2024

Prognostic model and failure mechanisms of steam generators in Sodium-Cooled fast reactors

This paper presents a prognostic model for sodium-cooled fast reactor (SFR) steam generators (SGs). Here, the purpose of the model is to estimate the remaining useful life of SFR SGs and thus to support the decision-making of autonomous control. SFR SGs are of great interest for plant integrity due to their harsh operation environment. They operate at higher temperatures and higher coolant-to-steam pressure differences than those of current light water reactors (LWR). The severity of the SFR SG failure consequences, which include water-sodium contact, is another reason. Understanding its failure mechanisms is important for the development of its prognostic model. Based on our literature review and physics-based analysis, we concluded that creep would be a dominant degradation mode of SFR SGs due to SFR’s high-temperature and high-pressure environment. Thus, creep is the focus of the prognostic model. Various other failure modes were also investigated in this study. The mechanical fatigue due to flow-induced vibration is usually observed in early developmental phases and would not be an important issue during normal operation. The thermal fatigue due to thermal stripping is occasionally observed in other components in SFRs but does not affect SG integrity. Pure water stress corrosive crack, fretting, and so on are commonly observed in LWR SGs but are significantly less important in SFR SGs because of the high temperatures, high pressure differences, and chemical properties of liquid sodium. Based on these investigations, a prognostic model focusing on creep failures was developed. It estimates the failure probability profile by sampling the Larson-Miller parameter (LMP) and temperature and associated uncertainties through Monte Carlo methods. Two case studies were presented. The first one demonstrated the model’s capability to calculate the failure probability for a new specimen within a given time. If the tube is working under temperatures of 500C ± 3 and pressures of 15.2 MPa, which leads to LMP of 20,100 ± 50, the failure probabilities within 50, 70, and 90 years are approximately 0.1 %, 3.2 %, and 17.5 %. The second demonstrated how adjusting the workload can help to protect the integrity of the component. For an old tube reaching 99 % of its lifespan, continuing to run at temperatures of 500C ± 3 and LMP of 20,100 ± 50 leads to a failure probability of about 29.0 % within a year. If the temperature is reduced by 5C, the failure probability can be reduced to 2.5 %, and, if the pressure is also reduced such that the LMP is increased by 100, the failure probability can further be reduced to 0.12 %.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Reactor and fuel cycle performance of light water reactor fuel with 235 U enrichments above 5%

Recent advances in nuclear fuel materials research, particularly on the topic of accident-tolerant fuels, have brought up potential opportunities for expanding the operating envelope of existing light water reactors. As many of the performance improvements offered by these technologies may be most fully realized by increasing fuel enrichment beyond the standard 5% limit, this paper examines the potential reactor performance and fuel cycle performance of low-enriched uranium oxide fueled light water reactors by generically considering pressurized water reactors with 235 U enrichment from 5 to 7%. Advanced cladding, including accident-tolerant cladding, has the potential to increase fuel burnup limits related to hydrogen in the cladding that coincide with those limits associated with end-of-life reactivity. Therefore, higher enrichment will be necessary in order to realize the higher fuel burnups. This work includes evaluation of the fuel cycle length, discharge burnup, reactivity coefficients, and fuel cycle performance, including radioactive waste and environmental impact metrics per unit energy generated. The analysis was performed using the evaluation metrics from the US Department of Energy Office of Nuclear Energy Fuel Cycle Evaluation and Screening Study. The reactor performance and safety analysis show that enrichments between 5 and 7% would have similar fuel temperature and moderator temperature coefficients. However, the soluble boron coefficient would decrease in magnitude, requiring more corrosive boric acid in the coolant or other methods of reactivity control during the fuel cycle. At these higher enrichments the maximum burnup at the rim of the fuel pellet would increase by almost a factor of two, which is expected to impact the formation of high-burnup structure in the fuel and the corresponding thermo-mechanical fuel properties. The fuel cycle performance assessment shows that increasing enrichment reduces the quantity of high-level waste disposed per unit energy generated, but it increases the natural resource requirements normalized to a gigawatt-electricity-per-year basis. Another impact is the slightly higher discharge burnup, resulting in somewhat different activity levels of the spent nuclear fuel and high-level waste radioactivity at 100 and 100,000 years after fuel discharge. The environmental impacts—including land use, water use, carbon emission, and radiological exposure—are of the same magnitude per unit energy generated. Finally, however, the impacts are distributed differently. Less than 5% enrichment has marginally more impact on the back-end of the fuel cycle, and greater than 5% enrichment has marginally more impact on the front-end of the fuel cycle. Ultimately, no neutronic or reactor safety hindrances to employing light water reactor fuel with enrichments greater than 5% are identified; given the achievable reactor performance benefits with advanced fuels, further practical exploration of increased enrichment fuel is recommended.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Reflectance of rhenium as a function of pressure in a diamond anvil cell

We have measured the reflectance of rhenium in the visible region to pressures up to 100 GPa in a diamond anvil cell (DAC). By photographing the reflecting surface, we visually show that there are challenges to obtaining accurate values in a DAC for several reasons, including cupping of the diamonds and roughening of the surface with the increase in pressure. We propose some useful procedures, such as careful alignment of the incident light and using thin gaskets to minimize cupping of the diamonds as well as measurement in the central region of the diamond culet. We also show that knowledge of the reflectance of rhenium can overcome the problem of absorption of light by diamonds when studying the reflectance of materials at high pressure in a DAC.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Surface Energy Modulated Self‐Assembly of Percolative Gallium Nanodroplet Films for Stretchable Electronics

Advancements in soft robotics and wearable technologies have led to an increased need for flexible and stretchable electronic systems. Liquid metals like Gallium (Ga) and its alloys offer high potential in the field of stretchable electronics and photonics due to their inherent high conductivity and malleability. However, their high surface tension and native oxide formation hinder uniform wetting and continuous film formation to get conducting films. Here, we report a fabrication strategy to realize electrically conductive Ga thin films with effective thicknesses around 100 nm on polymeric and elastomeric substrates. By enhancing the surface energy of the elastomer, we create uniform Ga nanodroplets capable of sustaining stretchability up to 200% strain. Our devices exhibit electronic conduction primarily through tunneling and display strain tunable piezoresistive characteristics, which are explained using Kirchhoff's resistive network and Simmon's analytical tunneling current model. To showcase the device's capability in fields of stretchable electronics, we demonstrate several functional prototypes, including flexible devices integrated with Light Emitting Diodes (LEDs), curvature and pressure sensors, and soft robotic grippers capable of sensing object curvature. The demonstrated devices highlight the potential of this approach for scalable integration of stretchable electronics in soft robotic and wearable platforms.

42 ENGINEERING↗
DOE OSTI2025

Risk assessment of wellbore leakage during underground hydrogen storage

The expansion of renewable energy sources would require large-scale energy storage options to overcome the intermittent nature of these sources. Underground hydrogen storage (UHS) in depleted hydrocarbon reservoirs offers a scalable and practical energy storage solution. These reservoirs are chosen for their availability and large capacity, but the unique properties of hydrogen raise concerns about potential leakage pathways, particularly through wellbores. In this study, we develop and apply, for the first time, reduced-order models (ROMs) specifically designed for efficient leakage risk prediction in UHS systems operating in depleted hydrocarbon reservoirs. Using 3,000 high-fidelity simulation scenarios, we examine the influence of 11 key parameters, including reservoir and aquifer depths, wellbore permeability and porosity, initial saturations of water, oil and gas fractions (hydrogen, light, intermediate, and heavy hydrocarbons), reservoir pressure multiplier, and the aquifer-to-reservoir volume ratio, to simulate leakage behavior over a 1,000-year timescale. We train ROMs using a two-step classification-regression approach, achieving R 2 values exceeding 99 % across all targets. These ROMs effectively capture the leakage evolution and identify critical controls of leakage, guiding the design of mitigation strategies. Results indicate that gas leakage occurs in about 27 % of scenarios as early as five years post-operation, reaching volumes of up to 106 ft3. Oil leakage is less frequent (~17 %) and typically begins decades later. Our findings also show that hydrogen often migrates first, owing to its smaller molecular size and higher buoyancy, followed by heavier hydrocarbons. Over time, these heavier components contribute significantly to the total leaked volume, reinforcing the need for targeted monitoring and remediation strategies. Our analysis highlights that deeper storage reservoirs, shallower aquifers, and low-permeability wellbores significantly reduce leakage risks. In conclusion, this work offers a robust framework for risk-informed UHS deployment, supporting energy security through reliable large-scale hydrogen storage while safeguarding environmental integrity.

08 HYDROGEN↗
DOE OSTI2021

High-fidelity kinetic modeling of instabilities and gyromotion physics in nonuniform low-beta plasmas

A fourth-order accurate continuum kinetic Vlasov solver and a systematic method for constructing customizable kinetic equilibria are demonstrated to be powerful tools for the study of nonuniform collisionless low-beta plasmas. The noise-free methodology is applied to investigate two gradient-driven instabilities in 4D (x,y,vx,vy) phase space: the Kelvin–Helmholtz instability and the lower hybrid drift instability. Nonuniform two-species configurations where ion gyroradii are comparable to gradient scale lengths are explored. The approach sheds light on the evolution of the pressure tensor in Kelvin–Helmholtz instabilities and demonstrates that the associated stress tensor deviates significantly from the gyroviscous stress tensor. Even at high magnetization, first-order approximations to finite-gyromotion physics are shown to be inadequate for the Kelvin–Helmholtz instability, as shear scales evolve to become on par with gyromotion scales. The methodology facilitates exploring transport and energy partitioning properties associated with lower hybrid drift instabilities in low-beta plasma configurations. Distribution function features are captured in detail, including the formation of local extrema in the vicinity of particle-wave resonances. Finally, the approach enables detailed targeted investigations and advances kinetic simulation capability for plasmas in which gyromotion plays an important role.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Measurements of the thermal Sunyaev-Zel’dovich effect with ACT and DESI luminous red galaxies

Cosmic Microwave Background (CMB) photons scatter off the free-electron gas in galaxies and clusters, allowing us to use the CMB as a backlight to probe the gas in and around low-redshift galaxies. The thermal Sunyaev-Zel’dovich effect, sourced by hot electrons in high-density environments, measures the thermal pressure of the target objects, shedding light on halo thermodynamics and galaxy formation, and providing a path toward understanding the baryon distribution around cosmic structures. We use a combination of high-resolution CMB maps from the Atacama Cosmology Telescope and photometric luminous red galaxy catalogs from the Dark Energy Spectroscopic Instrument to measure the thermal Sunyaev-Zel’dovich signal in four redshift bins from 𝑧 = 0.4 to 𝑧 = 1.2, with a combined detection significance of 19⁢𝜎 when stacking on the fiducial CMB Compton-𝑦 map. We discuss possible sources of contamination, finding that residual dust emission associated with the target galaxies is important and limits current analyses. We discuss several mitigation strategies and quantify the residual modeling uncertainty. Furthermore, this work complements closely related measurements of the kinematic Sunyaev-Zel’dovich and weak lensing of the same galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Dispenser Reliability: Materials R&D. A Hydrogen Fueling Infrastructure Research and Station Technology (H2FIRST) Report

Dispensers are the top cause of maintenance events and down-time at hydrogen fueling stations. In an effort to help characterize and enable improvements in dispenser reliability, an extensive accelerated lifetime testing set-up was designed and built at NREL involving components typically part of dispensing operations at fueling stations. Device Under Test (DUTs) included different components such as normally open valves, normally closed valves, fueling nozzles, breakaways devices and filters. Conditions of testing included pressures, and flow rates similar to light duty fuel cell electric vehicles fueling at -40°C, and -20°C for thousands of cycles in hydrogen. Tested components (failed and non-failed) were disassembled at SNL and polymeric O-rings were carefully retrieved and cataloged for chemical and physical characterization. Data collected was compared to similar O-rings from unexposed or non-tested components for hydrogen effects, and failure modes. Degradation analyses, based on select polymer chemistries common across all component types, their location within components, visual assessment of damage coupled with strong hydrogen effects from chemical characterization, was completed and presented to NREL and DOE. Overall, the failure rate amongst the components was not as high as expected for the test conditions. Among the component types tested, breakaways were the most susceptible to damage under these test conditions, with fueling nozzles a close second. The proper combination of selection of the right polymer and optimum component design was found to make a strong difference in component reliability under severe dispenser operating conditions. Physical degradation of polymers, rather than chemical changes due to low temperature hydrogen exposure, is more prevalent as failure mode for these test conditions. The nature and the extent of the degradation was much less at -20°C as compared to -40°C. The damage and failure rates were higher at lower temperatures than at higher test temperatures. As expected, increasing the number of cycles at the lowest test temperature (-40°C) increased damage. This indicates that cycling at the low temperature of -40°C required by SAE J2601 can reduce component life in fuel dispensing operations

08 HYDROGEN↗
DOE OSTI2021

Smart Labs Final Report Summer 2021

The Smart Labs Project at Los Alamos National Laboratory (LANL) is an initiative derived from The University of California, Irvine and is part of the Department of Energy’s (DOE) Better Buildings Challenge. These carbon abatement strategies aim to reduce energy consumption of laboratories while also maintaining health and safety requirements. Smart Labs designs incorporate seven key principles which are: digital control systems, demand-based ventilation, low power-density demand-based lighting, exhaust fan discharge velocity optimization, pressure drop optimization, fume hood flow optimization, and commissioning with automated cross-platform fault detection. As the ALDCP Smart Labs team for the summer of 2021, the scope of the project is to determine the energy savings within building 03-1698 (Material Science Laboratory - MSL). Over the past couple of years, the Sustainability Group has been adding Smart Labs upgrades into the MSL building and the summer team would like to understand the impact made for the overall energy consumption/demand and safety for the building, determine the overall return on investment (ROI), and recommend more Smart Labs upgrades that can be added to the MSL building. The goal is to enable the UI FOD (Utilities and Infrastructure Facility Operation Division) to promote more Smart Labs projects in the future and further the reputation LANL and DOE facilities have of being leading examples of developers of high performing buildings.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Photo-Reactive Amine-Based Direct Air Capture and Conversion of CO2

This study presents a novel photochemical approach to direct air capture (DAC) and CO2 conversion, utilizing a ruthenium-modified mesoporous TiO2 composite infused with linear polyethyleneimine (L-PEI) and enhanced by light absorbing and earth abundant titanium nitride (TiN). This light-activated system operates at ambient pressure and addresses long-standing challenges in conventional amine-based thermal reactive carbon capture (RCC), including amine degradation and CO2 slip. Our findings demonstrate that L-PEI effectively stabilizes CO2 adsorption and facilitates high-yield methanation over 50 cycles with a non-flammable forming gas mixture (approximately 5% H2). Comparatively, composites incorporating small-molecule amines exhibited poor stability under illumination, while highly mobilie branched PEI (B-PEI) formulations suffered from significant catalyst deactivation. A technoeconomic analysis suggests that methane synthesis via this platform could be achieved at costs below $5/kg under current electrocatalytic hydrogen pricing. These findings highlight the potential of this approach to enhance energy security by enabling decentralized, scalable fuel production from atmospheric CO2.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Nuclear Reactor Heat Extraction for Synthetic Fuel Plants

This report looks at the viability and best approach when producing synthetic fuels using heat and power supplied by advanced nuclear energy systems. The report looks at a low temperature integration pathway with four types of advanced reactors: a pressurized water reactor (PWR), an advanced light water reactor (A-LWR), a sodium fast reactor (SFR), and a high-temperature gas-cooled reactor (HTGR). A failure modes and effects analysis (FMEA) of the coupling system between the nuclear plant and the synthetic fuel systems is performed with the goal of identifying the reliability of such a thermal delivery system. Furthermore, a high temperature pathway is investigated for synfuel coupling to determine if this is more efficient and more cost effective as a coupling approach.

10 - SYNTHETIC FUELS↗
DOE OSTI2020

Real-Time Dynamic Brake Assessment for Heavy Commercial Vehicle Safety

This paper summarizes initial results and findings of a model developed to determine the braking performance of commercial motor vehicles in motion regardless of brake type or gross weight. Real-world data collected by Oak Ridge National Laboratory for a U.S. Department of Energy study was used to validate the model. Expanding on previous proof-of-concept research showing the linear relationship of brake application pressure and deceleration additional parameters such as elevation were added to the model. Outputs from the model consist of coefficients calculated for every constant pressure braking event from a vehicle that can be used to calculate a deceleration and thus compute a stopping distance for a given scenario. Using brake application pressure profiles derived from the dataset, stopping distances for light and heavy loads of the same vehicle were compared for various speed and road grades. For a constant brake application pressure profile (i.e. the pressure is relatively constant throughout the entire stop) it was shown that the lighter vehicle was able to stop in a shorter distance than the heavier vehicle in most scenarios other than large uphill grades. Significant changes in weight can be observed through the fuel efficiency of the vehicle to determine if the model needs to be calibrated with new or additional braking events. The model was initially developed for tracking brake performance to inform routine maintenance and the ordering of vehicles in a platoon but can be expanded to other connected and automated research areas.

Siekmann, Adam↗