Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOADS - PLATES, RECTANGULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Lifting-surface theory for a semi-infinite wing in oblique gust

An unsteady lifting-surface theory is developed for the calculation of the airload on a semi-infinite-span thin wing in a compressible flow due to interaction with an oblique gust. By using the solutions obtained for a two-dimensional wing, the problem is formulated so that the unknown is taken to be the difference between the airload on the semi-infinite wing and that on a two-dimensional wing under the same gust conditions. Since this airload difference is nonzero only near the wing tip, the control points need be distributed in the tip region only; this significantly simplifies the numerical procedure. Results are presented for a wing with rectangular tip. The implication for noise and unsteady loads due to blade-vortex interaction for helicopter rotors is discussed.

Chu, S.↗
NASA NTRS1984

An atomistic model of slip formation

The results of an atomistic model for the simulation of the early stages of crack initiation in a two-dimensional triangular lattice are presented. In the current model, each particle in the system is treated discretely and assumed to be interacting with the surrounding particles via Lennard-Jones potentials. A uniaxial load (in incremental elongations) is applied to the rectangular two-dimensional slab in either the x or the y direction. After each incremental elongation the system is equilibrated using a static method. Initially, elastic behavior in the x and y directions is observed. Continued elongation results in plastic deformation. In lattices with point defects, the defects first move to the surface, creating vacancies which trigger plastic deformation.

Halicioglu, T.↗
NASA NTRS1929

Pressure Distribution Over a Rectangular Monoplane Wing Model up to 90 Degree Angle of Attack

The pressure distribution tests described in this report, covering angles of attack up to 90 degrees, were made on a rectangular monoplane wing model in the atmospheric wind tunnel of the Langley Memorial Aeronautical Laboratory. These tests indicate that a rectangular wing, by reason of its large tip loads, is uneconomical aerodynamically and structurally, has pronounced lateral instability above maximum lift, and is not adaptable to accurate calculation based on the classical wing theory. (author)

Knight, Montgomery↗
NASA NTRS1992

RCS reduction of a microstrip patch using lumped loads

In this report we consider the radar cross section (RCS) of a single rectangular patch antenna in a recessed cavity. Using a previously developed finite element-boundary integral method code, a study is performed on the patch's RCS as a function of frequency. To reduce the RCS of the patch at the resonant frequency, lumped (resistive) loads are placed at the edges of the patch. The effects of the lumped loads on the patch's RCS and gain are examined and it is observed that the RCS and gain are reduced as the as the load value decreases, whereas the antenna's bandwidth is increased. At resonance, the usual relations between the RCS and gain is observed, but it is shown that this relation no longer holds at frequencies away from resonance.

Volakis, John L.↗
NASA NTRS1976

Arrangement of vortex lattices

A new method is developed for solving the lifting-surface equation for thin wings. The solution requires the downwash equation to be in the form of Cauchy integrals which can be interpreted as a vortex lattice with the positions of the vortices and control points dictated by the finite sum used to approximate the integrals involved. Lan's continuous loading method is employed for the chordwise integral since it properly accounts for the leading-edge singularity, Cauchy singularity, and Kutta condition. Unlike Lan, the spanwise loading is also continuous and the Cauchy singularity in the spanwise integral is also properly accounted for by using the midpoint trapezoidal rule and the theory of Chebyshev polynomials. This technique yields the exact classical solution to Prandtl's lifting-line equation.The solution to the lifting-surface equation for rectangular wings was found to compare well with other continuous loading methods, but with much smaller computational times, and to converge faster than other vortex lattice methods.

Dejarnette, F. R.↗
NASA NTRS1974

Versatile electronic load

Variable load has very fast response under wide range of simulated dynamic operating conditions, and can accept inputs up to 1000 watts. Many types of signals may be applied to load. Variable pulse generator and flip-flop produce rectangular waveform. Other signals include steady state step and single pulse.

Mussen, K. R.↗
NASA NTRS1992

Discrete distributed strain sensing of intelligent structures

Techniques are developed for the design of discrete highly distributed sensor systems for use in intelligent structures. First the functional requirements for such a system are presented. Discrete spatially averaging strain sensors are then identified as satisfying the functional requirements. A variety of spatial weightings for spatially averaging sensors are examined, and their wave number characteristics are determined. Preferable spatial weightings are identified. Several numerical integration rules used to integrate such sensors in order to determine the global deflection of the structure are discussed. A numerical simulation is conducted using point and rectangular sensors mounted on a cantilevered beam under static loading. Gage factor and sensor position uncertainties are incorporated to assess the absolute error and standard deviation of the error in the estimated tip displacement found by numerically integrating the sensor outputs. An experiment is carried out using a statically loaded cantilevered beam with five point sensors. It is found that in most cases the actual experimental error is within one standard deviation of the absolute error as found in the numerical simulation.

Anderson, Mark S.↗
NASA NTRS1972

Automated testing data reduction computer program

The capability of a computer program which can be part of a larger computer program for a fully automated multiaxial testing facility is described. The program was designed to process test data from tubular or flat specimens made from isotropic or anistropic materials, including high modulus fiber composites. Data from a large number of strain gages and combinations of applied loads can be used. Options are provided for single element, 90-degree, rectangular or Delta rosettes, or any combinations of these types of strain gages. Options are provided for strain gage transverse sensitivities. The program outputs include: structural axes strains and stresses, initial and strain-dependent elastic constants, shift of principal strain direction with load, and local curvatures from back-to-back strain gages, and either Calcomp or microfilm plots. The computer program is described with respect to its flow chart, input/output, embedding or linking with other programs.

Chamis, C. C.↗
NASA NTRS1979

Bumblebee Program: Aerodynamic data. Part 4: Wing loads at Mach numbers 1.5 and 2.0

Individual wing panel aerodynamic characteristics are provided for rectangular wings with aspect ratios of 0.25, 0.75, and 1.00 each panel at Mach numbers if 1.5 and 2.0 for angles of attack to 23 degrees. Data plots produced from reports of wind tunnel tests show normal force coefficients, and the spanwise and chordwise center of pressure locations.

Barnes, G. A.↗
NASA NTRS1951

Torsion and bending of prismatic rods of hollow rectangular section

The torsion and bending of hollow rectangular beams was investigated without the requirement that wall thickness be small compared with the transverse dimensions. The limits of applicability of the usual Bredt formula are indicated for the case of a square hollow tube in torsion. Formulas are given for bending stresses at different parts of the cross section of a hollow rectangular beam.

BOXES, STRUCTURAL↗
NASA NTRS1945

A method for determining the camber and twist of a surface to support a given distribution of lift, with applications to the load over a sweptback wing

A graphical method is described for finding the shape (camber and twist) of an airfoil having an arbitrary distribution of lift. The method consists in replacing the lifting surface and its wake with an equivalent arrangement of vortices and in finding the associated vertical velocities. By division of the vortex pattern into circular strips concentric about the downwash point instead of into the usual rectangular strips, the lifting surface is reduced for each downwash point to an equivalent loaded line for which the induced velocity is readily computed. The ratio of the vertical velocity to the stream velocity is the slope of the surface in the free-stream direction.

Cohen, Doris↗
NASA NTRS2007

Failure Maps for Rectangular 17-4PH Stainless Steel Sandwiched Foam Panels

A new and innovative concept is proposed for designing lightweight fan blades for aircraft engines using commercially available 17-4PH precipitation hardened stainless steel. Rotating fan blades in aircraft engines experience a complex loading state consisting of combinations of centrifugal, distributed pressure and torsional loads. Theoretical failure plastic collapse maps, showing plots of the foam relative density versus face sheet thickness, t, normalized by the fan blade span length, L, have been generated for rectangular 17-4PH sandwiched foam panels under these three loading modes assuming three failure plastic collapse modes. These maps show that the 17-4PH sandwiched foam panels can fail by either the yielding of the face sheets, yielding of the foam core or wrinkling of the face sheets depending on foam relative density, the magnitude of t/L and the loading mode. The design envelop of a generic fan blade is superimposed on the maps to provide valuable insights on the probable failure modes in a sandwiched foam fan blade.

Raj, S. V.↗
NASA NTRS1984

Acoustic measurements of a full-scale rotor with four tip shapes. Volume 1: Text, appendices A and B

A full-scale helicopter with four different blade-tip geometries was tested in the 40- by 80-foot wind tunnel at Ames Research Center. Performance, loads, and noise were measured. The four tip shapes tested were rectangular, tapered, swept, and swept-tapered. Noise measurements from that test are presented in the form of tables and plots. The noise data include measurements of the sound pressure level in dB, dBA, and tone-corrected PNdB, for all of the conditions tested. Detailed measurements, 1/3-octave spectra and time-histories for some selected data are included as well as plots of dBA as function of test condition. Some performance measurements are given to aid interpretation of the noise data.

Mosher, M.↗
NASA NTRS1984

Acoustic measurements of a full-scale rotor with four tip shapes. Volume 2: Appendices C, D, E and F

A full scale helicopter with four different blade tip geometries is tested in a 40- by 80-foot wind tunnel. Performance, loads, and noise are measured. The four tip shapes tested were rectangular, tapered, swept, and swept/tapered. The noise data include measurements of the sound pressure levels in decibels dB, decibels adjusted dBA, and tone-corrected PNdB, for all of the conditions tested. Also included are the detailed measurements, 1/3 octave spectra and time histories for some selected data, and plots of dBA as function of test condition. Some performance measurements are included to aid interpretation of the noise data.

Mosher, M.↗
NASA NTRS1937

The Lateral Instability of Deep Rectangular Beams

Experimental and analytical studies were made of solid and hollow deep rectangular beams to study their lateral instability under various conditions of loading and restraint. The tests were made on bars and tubes of 17ST aluminum alloy. Failure by lateral buckling occurred only in tests on the solid beams. It was found that, within the elastic range, the test results were in agreement with the classical theory for the lateral buckling of deep beams as given by Prandtl, Mitchell, and Timoshenko. The tests were extended to the inelastic range, where it was found that the substitution for Young's modulus of an average modulus of elasticity derived from the stress-strain curve made it possible to predict instability at high stresses.

Dumont, C↗
NASA NTRS1955

Theoretical study of the tunnel-boundary lift interference due to slotted walls in the presence of the trailing-vortex system of a lifting model

The equations presented in this report give the interference on the trailing-vortex system of a uniformly loaded finite-span wing in a circular tunnel containing partly open and partly closed walls, with special reference to symmetrical arrangements of the open and closed portions. Methods are given for extending the equations to include tunnel shapes other than circular. The rectangular tunnel is used to demonstrate these methods. The equations are also extended to nonuniformly loaded wings.

Matthews, Clarence W↗