Search NASA⌕ Search

SEARCH · Search NASA

Results for “LUBRICATING OIL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Persistent Elevated Soot Emissions Induced by Clustered Stochastic Preignition Events

Stochastic Preignition (SPI) is an abnormal combustion phenomenon that can occur in spark-ignition engines particularly under high-load operation. SPI is characterized by uncontrolled initiation of combustion prior to spark discharge, an abnormal combustion process that can lead to severe knock events and significant engine damage. SPI has been associated with fuel properties, lubricant composition, and engine design and operation. Here, in this work, a single-cylinder test engine with a dry-sump oil system was utilized to study the SPI response of E10 and E25 fuels with a range of Reid Vapor Pressure (RVP). An automated test procedure was employed, consisting of ten square-waved load profile segments, with each segment composed of 5 min of low-load operation followed by 25 min of sustained high-load operation. These tests were replicated across multiple days of testing including a lubricant triple flush between tests, and an online Fuel in Oil diagnostic measurement. Exhaust particulate emissions were continuously measured by an AVL microsoot sensor (MSS). Elevated particulate matter emissions were observed to occur concurrently with SPI events as blooms of soot. Particularly after clustered events (i.e., multiple SPI cycles occurring within 10 consecutive engine cycles), high soot emissions were observed to persist over several days of sequential operation despite daily lubricant changes, a complete warm-up procedure, and sustained low-load operation between test segments. This result implies that the particulate emissions trends may be dominated by deposit-based effects, where higher load operation is needed to alter deposition and formation processes. The observed soot blooms were also found to correspond to a reduction in the engine fueling and the fuel engine oil dilution rate despite the engine exhaust remaining at stoichiometric exhaust operation. These observations suggest that post-SPI events, pathways for lubricant migration and consumption into the combustion chamber may occur until these pathways are closed from deposit formation or ring dynamics during extended operation. These observed sooting propensity persisted with all fuels tests, but a linear correlation was observed between the summation of soot and particulate matter index (PMI) value for each fuel as well as SPI events, proving that PMI is a crucial fuel property for reducing SPI.

Splitter, Derek [Oak Ridge National Laboratory (OR↗
DOE OSTI2021

Identification and analysis of stem‐specific promoters from sugarcane and energy cane for oil accumulation in their stems

Abstract Considerable recent progress has been achieved in bioengineering oil accumulation in the vegetative tissues of plants, opening an opportunity for large scale production of biodiesel, jet fuel, lubricants, and high‐value lipid bioproducts. For the highly productive C4 crops, such as sugarcane, energy cane, Miscanthus, and fiber sorghums, the bulk of the biomass is the stem. However, little success has been made in accumulating oil in the stem. Since engineering a trait with a constitutive promoter often results in pleiotropic effects that counter trait improvement, identification of stem parenchyma‐specific promoters is a prerequisite for efficient use of the ample photoassimilates stored in mature stem parenchyma cells. In this study, we first identified two TST genes encoding homologues of tonoplast sugar transporters that were strongly and almost exclusively expressed in the stems of canes via a combination of RNA‐seq atlas analysis, in silico analysis of a sugarcane genome, phylogenetic analysis, and quantitative PCR analysis. They were further confirmed in the pith parenchyma cells of the mature stem by RNA in situ hybridization. When fused with the β‐Glucuronidase (GUS) reporter gene, the promoters of two alleles, TST2b‐1A and TST2b‐1C , from one TST gene demonstrated that they could drive the GUS expression exclusively in the stem in Arabidopsis.

09 BIOMASS FUELS↗
DOE OSTI2026

Handling and Properties of Methanol as a Marine Fuel

Given the increasing concern around greenhouse gas emissions and the decline in the availability of fossil fuels, there is increasing global demand to develop alternate fuels for maritime transportation that are sustainable and which have lower greenhouse gas emissions. Methanol is one such alternative fuel that has garnered considerable attention given its potential to be produced by more sustainable processes and its more favorable greenhouse gas emission profile in comparison with current fossil fuels. Understanding the physical and chemical properties of methanol under a range of conditions is essential for its development as a marine fuel. In this study, we seek to define physical and chemical properties of different methanol samples to simulate real-world storage conditions as these data are lacking in the literature. Several methanol samples were evaluated: nearly pure methanol; International Organization for Standardization (ISO) marine methanol (MM) grades A, B, and C; and methanol plus higher alcohols. We first evaluated all methanol samples for impurities, acetic acid content, density, and distillation range. We then characterized the effects of water absorption and found that methanol can easily absorb unacceptable water content from humid air within hours, necessitating storage conditions that prevent this process. In eight-week aging experiments at 20 °C and 40 °C in ambient air, we did not observe significant oxidation for any of the methanol samples; however, we did observe increases in acid number. We assessed the impact of contamination of methanol with water, marine gas oil (MGO), and an MGO–biodiesel mixture on density, viscosity, distillation range, and lubricity. Finally, we show that MGO contamination of methanol results in a slight increase in sooting tendency. In aggregate, our results provide an in-depth analysis of physical and chemical properties of methanol as well as the impacts of storage conditions and impurities on the properties of fuel methanol.

09 BIOMASS FUELS↗
DOE OSTI2024

Competition Between Growth and Removal in Zirconia Nanocrystal-Derived Tribofilms: The Role of Co-additives

Antiwear additives permit energy-efficient lubrication of gearboxes, bearings, and other tribological interfaces. We study zirconia (ZrO 2 ) nanocrystal additives, which readily form protective tribofilms in tribological contacts. Our prior work demonstrated cooperative antiwear performance between ZrO 2 and the S- and P-based co-additives in fully formulated hydrocarbon gear oils. Here, we extend that work by examining the growth kinetics of the ZrO 2 tribofilms, including the influence of the co-additives. In the boundary lubrication regime for mixed rolling-sliding contacts, the initial phase of ZrO 2 tribofilm growth is soon overtaken by removal processes, phenomena whose importance has gone unnoticed in prior work. Tribofilm removal affects the steady-state thickness and morphology of the tribofilm as well as its growth kinetics. The S- and P-based co-additives are incorporated into the ZrO 2 tribofilm, and alter the competition between the growth and removal processes, increasing initial net growth rates per contact cycle and contributing to a more polished final interface. This work highlights the significance of removal processes in determining tribofilm antiwear performance, and suggests several routes for improving tribofilm growth kinetics using co-additives.

Coadditives↗
DOE OSTI2020

Material-Dependent Antagonistic Effects between Soot and ZDDP

While soot in engine oil is known to accelerate the wear of diesel and gasoline direct-injection compression-ignition engines, there is a lack of consensus on the wear mechanism though various hypotheses have been proposed in the literature. Particularly, some recently observed antagonistic effects between soot and a common lubricant antiwear additive, zinc dialkyldithiophosphate (ZDDP), while others did not. The discrepancy is, in part, explained by the strong alloy dependence of such antagonism discovered in this study. Specifically, four alloys, 52100 steel and M2, M50, and A2 tool steels, are tested in lubricants containing carbon black (CB, a soot surrogate) with and without ZDDP present. Adding the CB alone to the oil increases the wear rate for all steel alloys as expected. However, distinct wear performance is observed for the four steel alloys when ZDDP is introduced to the CB-containing oil: while the 52100 steel has notable wear reduction, the three tool steels suffer significant wear increase. Comprehensive tribofilm characterization suggests that the Mo content in the steel alloy and the sulfur from ZDDP strongly influence wear behavior. The combination of CB/Mo-catalyzed sulfidation and CB-accelerated abrasion is hypothesized to be responsible for the high wear of the Mo-alloyed tool steels.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Identification of triacylglycerol remodeling mechanism to synthesize unusual fatty acid containing oils

Abstract Typical plant membranes and storage lipids are comprised of five common fatty acids yet over 450 unusual fatty acids accumulate in seed oils of various plant species. Plant oils are important human and animal nutrients, while some unusual fatty acids such as hydroxylated fatty acids (HFA) are used in the chemical industry (lubricants, paints, polymers, cosmetics, etc.). Most unusual fatty acids are extracted from non-agronomic crops leading to high production costs. Attempts to engineer HFA into crops are unsuccessful due to bottlenecks in the overlapping pathways of oil and membrane lipid synthesis where HFA are not compatible. Physaria fendleri naturally overcomes these bottlenecks through a triacylglycerol (TAG) remodeling mechanism where HFA are incorporated into TAG after initial synthesis. TAG remodeling involves a unique TAG lipase and two diacylglycerol acyltransferases (DGAT) that are selective for different stereochemical and acyl-containing species of diacylglycerol within a synthesis, partial degradation, and resynthesis cycle. The TAG lipase interacts with DGAT1, localizes to the endoplasmic reticulum (with the DGATs) and to puncta around the lipid droplet, likely forming a TAG remodeling metabolon near the lipid droplet-ER junction. Each characterized DGAT and TAG lipase can increase HFA accumulation in engineered seed oils.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Dynamic, hollow nanotubular networks with superadjustable pH-responsive and temperature resistant rheological characteristics

Recently, the interest in stimuli-responsive and adaptable materials has continuously grown in various fields and applications. For such responsive systems, different triggers, including pH, light, pressure, temperature, and electric field, have been utilized to control dynamics and assembly. Among these, pH is one of the most convenient, energy-efficient, and economic modalities. Besides, plenty of traditional materials have poor thermal and salt stability, limiting their applications. Herein, we report a new design of a pH-responsive viscoelastic supramolecular complex (VSC) based on commplexation of a new long-chain amino-amide and maleic acid. In this study, the system demonstrated a sol–gel-sol transition from pH 2 to 10, with the largest static viscosity occurring at pH 6 (~1000 Pa·s) and the smallest viscosity at pH 4 (~3.3 Pa·s), indicating ~ 300-fold control over the viscosity. For a given concentration, the static viscosity of VSC was about 15 times larger than that of CTAB/NaSal, a well-established dynamic viscoelastic system, and no pH-responsiveness was observed for the traditional system. In addition, the VSC demonstrated a superior temperature tolerance and lower temperature dependence. The potential of these intriguing dynamics viscoelastic systems was evaluated for hydraulic fracturing and enhanced oil recovery applications. Proppant settling velocity of DMAA/MA was 500 ~ 1000 times lower than that of CTAB/NaSal and common traditional polymers. Likewise, the oil recovery percentage could be significantly improved with the utilization of DMAA/MA compared to the CTAB/NaSal (86 % vs 52 %). Aside from applications in hydraulic fracturing and enhanced oil recovery, we anticipate that the intriguing rheological properties of this viscoelastic system can be beneficial for other chemical engineering applications including personal care products, cosmetics, lubricants, and biomedical gels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Effect of Oil Viscosity and Impact of Ionic Liquid Additive on Electrically Induced Pitting in Rolling Contact

Electrically induced bearing damage (EIBD) is a growing concern in electric drivetrains, where electrical discharge currents generate localized pitting that accelerates wear and premature failure. While ionic liquids (ILs) have shown promise as lubricant additives due to their natural physical adsorption, strong capabilities of tribofilm formation, and high molecular tunability, their role in mitigating EIBD is little known. This gap is especially evident because lubricant viscosity and film thickness affect discharge behavior, and additive performance in these regimes has not been well explored. In this study, tribological tests were performed using a ball-on-disk pure rolling-contact system under an applied voltage on polyalphaolefin oils of three viscosities (4, 10, and 150 cSt measured at 100 °C), with and without the addition of a phosphonium-phosphate IL. Surface damage was analyzed using scanning electron microscopy (SEM) and stylus profilometry. Damage quantification was based on pit morphology analysis of SEM images. The results provide new insights into how oil viscosity governs the discharge behavior and how an IL additive could influence the pit formation. While viscosity seems to play a significant role, an IL additive shows potential to reduce EIBD and deserves further study.

electrically induced bearing damage (EIBD)↗
DOE OSTI2021

Why does a phosphonium-phosphinate ionic liquid protect the contact surfaces from wear and micropitting but increase vibration when used as an additive in rolling-sliding lubrication?

A phosphonium-phosphinate ionic liquid (IL) was studied as a lubricant additive for rolling-sliding contacts. The bench-scale test was designed to simulate automotive rear axle operation during cold start, highway towing, and overload conditions. Adding such an IL (2%) into a base oil significantly reduced wear loss and rolling contact fatigue, e.g., microcracking and micropitting, but made the vibrational noise notably higher under a low (-1.5%) sliding roll ratio (SRR). Additionally, worn surface characterization revealed an interesting texture pattern with alternating smoother plateaus and rougher valleys, which is believed to cause the high vibration. No increased vibration was observed at a high (-30%) SRR, possibly because the more aggressive sliding abrasion prevented such a surface texture from forming.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ multimodal imaging for nanoscale visualization of tribofilm formation

A third of the energy from fuel combustion in passenger car gasoline engines is lost due to friction. Carefully designed engine lubricants can recover some of these losses by reducing friction and wear by forming a nanometer-scale chemico-physico tribofilm between surfaces. Accordingly, attention has focused on developing oil formulations that form low-friction tribofilms. However, analyses of resultant tribofilms are typically conducted after tribo-tests with conventional characterization tools and do not offer insights into tribofilm formation and evolution, precluding information critical to tuning tribofilm properties. In this work, we developed a unique multimodal methodology based on Atomic Force Microscopy (AFM) with local probe heating for in situ tribological studies that activates friction modifiers and simultaneously captures the evolution of friction and surface roughness, with nanometer resolution. As a platform to demonstrate the ability of this methodology to visualize dynamics of tribofilm formation in situ, we apply it to molybdenum-based friction modifiers to distinguish key factors in their functionality and correlate nanoscale AFM and Friction Force Microscopy data to bench tribo-tests used in the industry. To decode the formation mechanisms observed in situ and underlying chemistry of tribofilms, we performed ab initio Molecular Dynamics (AIMD) simulations at comparable conditions. AIMD simulations confirmed both nanoscale and bench tribo-test results and showed deviations in molecular organization in tribofilms that are formed from different molybdenum-based friction modifiers that corroborates with surface functionality. With this innovative methodology, we demonstrate proof-of-principle in situ formation of molybdenum-based tribofilms directly on steel surfaces that could be applied generally to studying tribofilm formation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Inhibition of Micro-pitting by Tribofilm-Forming ZrO 2 Nanocrystal Lubricant Additives: A Micro-pitting Rig and Transmission Electron Microscope Study

The drive to reduce fuel consumption in transportation has encouraged the emergence of low viscosity lubricants to reduce viscous losses in the engine, drivetrain, and other components. However, viscosity reduction increases the risk of surface damage, thus motivating the development of new anti-wear (AW) additives. Capped ZrO 2 nanocrystals (NCs) in base oils have been shown to form AW tribofilms within microscale sliding contacts. However, the potential of ZrO 2 NCs to protect surfaces subjected to rolling-sliding contact from macroscale damage, such as micro-pitting, remains unexplored. Here, we explore the ability of ZrO 2 NCs to form protective tribofilms under harsh conditions using a micro-pitting rig (MPR), consisting of a three ring-on-roller configuration. The experiments were conducted in polyalphaolephin (PAO) base oil, with and without 5 nm diameter ZrO 2 NCs, at two levels of slide-to-roll ratio (SRR) (30% and 0%) and at variable test durations up to long durations (119 h). MPR results showed the use of ZrO 2 NCs gives rise to the formation of a tribofilm covering the roller surfaces and decreases the initiation and propagation of micro-pits compared to tests in pure PAO base stock. Transmission electron microscopy (TEM) performed on focused ion beam (FIB) milled cross-sectional samples of the roller surfaces revealed the growth of dense and 50–100 nm thick ZrO 2 -based tribofilms independent of (SRR), indicating the potential for robust micro-pitting fatigue protection. Nevertheless, small cracks localized within the near surface region of the roller tested at the most severe conditions (30% SRR and 119 h) were observed. The initiation of these cracks was directly related to the presence of manganese sulphide (MnS) inclusions in the steel, revealed using TEM combined with energy dispersive spectroscopy (EDS). Furthermore, the results highlight the benefits of the protective tribofilms formed by ZrO 2 NCs and suggest approaches for further optimizing their use.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effects of Water Contamination on Micropitting and Rolling Contact Fatigue of Bearing Steels

Abstract In this research, the effects of water contamination in oil were investigated on two kinds of failures that occur in bearing steel: micropitting and rolling contact fatigue. Whereas the presence of water in the oil had little effect on the generation of surface wear in these experiments, increases in the occurrences of micropitting and rolling contact fatigue were observed due to the presence of either dissolved or free water in lubricants. Additionally, the presence of white etching matter at crack interfaces was observed and evaluated. The experimental results showed that water content can be considered as a significant factor that accelerates the formation of micropitting and fatigue cracks in rolling bearings.

Engineering↗
DOE OSTI2024

Marine Algae Industrialization Consortium (MAGIC): Combining biofuel and high-value bioproducts to meet the RFS

The Marine Algae Industrialization Consortium (MAGIC) was formed to address pressing challenges in the commercialization of microalgae as a source of biofuel. The “Marine Algae Industrialization Consortium (MAGIC): Combining biofuel and high-value bioproducts to meet the RFS” project formally addressed two US Department of Energy Bioenergy Technologies Office (BETO) goals: (1) Model the sustainable supply of 1 million metric tonnes ash free dry weight (AFDW) cultivated algal biomass and (2) Demonstrate valuable co-products produced along with biofuel intermediates to increase value of algal biomass by 30%. To achieve these goals, the project demonstrated and validated high-value co-products to drive down the cost of biofuel by increasing the value of algae “co-products” towards increasing the selling price of total algae biomass as one of the key drivers of economics and adoption. This was accomplished through five core, interdependent tasks including: (1) strain selection to identify and deliver strains for mass culture, (2) mass culture using a hybrid cultivation system and following key operating parameters for downstream applications to provide algae feedstock, (3) recovery and conversion to evaluate two alternative methods to separate dry algae biomass into oil and residuals for downstream testing, (4) product assessment to determine biofuel, aquafeed or poultry feed product efficacy using algae biomass fractions as well as to provide critical performance data for valuation and (5) commercialization to use technoeconomic and life cycle assessments (TEA/LCA) as iterative design and assessment tools including consideration of target markets, competitors, and distribution channels to guide product assessment, development and valuation. A total of 46 peer-review publications, many open-access, provide detail of much of the work carried out and the results of the tasks. Additional reports and presentations provide other technical and public engagement material. At a high level, using a variety of approaches, more than 1000 marine microalgae strains were evaluated to ultimately identify the seven winners that were down-selected to be grown in mass culture. Strain selection demonstrated that there were no ‘super strains’ and that each candidate had strengths and limitations for specific products, growth conditions or operational considerations. Mass culture growth of these seven strains at >5000 L / 29 m 2 scale found that four them were suitable for product assessment. More than 250 kg of biomass was produced across hundreds of pond runs along with thousands of cultivation entries on the growth and biomass characteristics as well as environmental parameters. In the process, dozens of standard operating procedures were generated as was custom software to process and analyze cultivation data. Recovery and conversion of algae biomass demonstrated that a hexane solvent based extraction protocol was most effective at recovering oil (biocrude) from algae and four strains were processed to produce oil and lipid extracted algae (residuals) for downstream testing. Membrane-based oil separation was less successful, but may still be applicable to other commercial applications in the future. Product testing demonstrated that algae biocrude is of high quality and hydrotreating generated numerous fractions of high quality composition for fuel and lubricate based applications. Aquafeed studies performed at a variety of scales showed that both whole and defatted (lipid extracted algae) microalgae were suitable as a feed ingredient, but that the specifics of the fed animal and biochemical composition of the algae are critical factors when determining formulation. Similarly, poultry studies on whole and defatted microalgae generally showed positive outcomes on animal growth and health, with some microalgae providing enhanced nutritional composition of the animal product. Economic and life cycle assessments covered a wide range of possible commercialization and sustainability scenarios. Replacement value, improved product value added, consumer values marketing added valuation and improved animal health were considered as alternatives for microalgae valuation. Using the open pond system, algae productivity was identified as the key driver of commercialization economics, but combination of co-products (e.g. animal feed) with biofuel production substantially increased the total selling price of algae. Modeled microalgae selling price exceeded $\$$1500/tonne and could generate competitive biofuel selling prices below $\$$5 gallon gas equivalents using realistic algal productivities. Short (process scale) and longer (decadal trends) sustainability assessments show that marine microalgae can enhance the sustainability of energy production and lead to other realized benefits in water, fertilizer and land use for other sectors (e.g. agriculture). This project successfully demonstrated all of the components of an end-to-end process from mass microalgae cultivation and dewatering, to recovery and conversion of algae biomass components, to final product demonstration and process valuation; the combined results provide a framework for future commercialization of algae based biofuels.

09 BIOMASS FUELS↗
DOE OSTI2022

Solvent-Induced Selectivity of Isoprene From Bio-Derived Prenol

In this work we demonstrate the selective catalytic conversion of prenol, which is an allylic alcohol that can be prepared from renewable resources to isoprene. The catalyst is an inexpensive molybdenum complex (Molyvan L) designed and used as an additive for lubricants. Isoprene is generated under relatively mild reaction parameters at 130–150°C, for 2 h, under vapor pressure conditions that do not exceed 50 psi. Two cases were studied: one in which Molyvan L was dissolved in a base oil at 1% concentration (weight/weight) and then mixed with a solvent and prenol and the other in which neat Molyvan L was introduced in the reaction and the base oil was replaced with the solvent and prenol. We investigated the selectivity of the reaction using the following solvents in both cases: dodecane, dodecanol, isododecane, octane, blendstock for oxygenate blending (BOB3), a fuel surrogate, a polyalphaolefin (PAO4), and methoxy polyethylene glycol (methoxy PEG350). Although conversion of prenol was above 94% in all experiments, isoprene was formed with various degrees of efficiency alongside a prenol isomeric alcohol, diprenyl ether and mixed ether via intramolecular and intermolecular dehydration reactions. Dodecane appeared to have the highest level of selectivity initially in base oil so we studied the effect of various dodecane-like solvents on isoprene yield and product profile. Surprisingly, octane (similar to dodecane) and isododecane (branched alkane) generated insignificant amounts of byproducts, essentially providing the highly desired isoprene with a very high selectivity. Branching of the solvent does not appear to have an effect on selectivity. Another advantage of this catalyst is the low loadings required to effect the transformation; that is, 0.25% (weight/volume) in the cases using neat Molyvan L and 0.5% (weight/volume) in the cases using Molyvan L dissolved in the base oil. Provided that prenol can be produced in large scale from bioresources, this work would enable the sustainable production of isoprene, in good yield, and with very high selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Multifunctional Tunable Polymethacrylates for Enhanced Shear Stability and Wear Prevention

This paper describes the design, synthesis, and characterization of linear, polar, and non-polar polymethacrylates designed for use as lubricant viscosity index improvers with enhanced shear and anti-wear resistance. The polymers were prepared via Reversible Addition-Fragmentation Chain Transfer (RAFT) to obtain relatively low, narrow, molecular weights, with random polar moieties. The resulting polymers were evaluated as oil solutions to determine their viscosity index, shear stability performance, and antiwear characteristics. The polymers had molecular weights (Mw) ranging from 120-170 kDa, and the resulting viscosity indexes (VIs) in general tracked the Mw. Although the VIs were modest (140-189), all polymers displayed higher values than a commercial product designed for similar applications, both at 2% (w/w) and when kinematic viscosities (KVs) were normalized to the lowest KV100 of ~5cSt. One of the imidazole-containing polymers displayed an anomalously high VI for a low apparent Mw. As hypothesized, many of the polar polymers demonstrated substantial wear reduction compared to the non-polar homopolymers or a commercial benchmark. The low-molecular-weight imidazole-containing polymer produced less than 4% of the wear displayed by the commercial standard. The higher molecular weight polymers containing imidazole, hydroxy group and amino group also produced as little as 10% of the wear shown by the benchmark. The strategy demonstrated the benefit of low, narrow, molecular weight polymers to achieve good shear stability in viscosity modifiers while minimizing wear, rendering them suitable for fluid-power applications.

friction modifiers↗
DOE OSTI2021

Investigation of main bearing operating conditions in a three-Point mount wind turbine drivetrain

Wear-related failures of spherical roller bearings in the main bearing position of three-point mount wind turbines have been higher than expected and can contribute to higher than anticipated operation-and-maintenance costs. In this paper, the operational conditions of such a main bearing—including measured axial displacement and velocity subject to the estimated axial loads—are described for an instrumented, commercial wind turbine. The field measurements suggest a maximum axial speed between the bearing rings that is less than 2 millimeters per second. It is estimated that the axial speed between the ring and rollers is approximately 25% of this value. When compared to a speed of rolling from approximately 200–352 millimeters per second, the measured axial sliding is therefore significantly less than 1% of the speed of rolling. Previous numerical studies of lubricant film formation in rolling contacts have shown that the effect of axial sliding starts to be noticeable only when this ratio exceeds 10%; therefore, the axial velocity represents only a small disturbance to the nominal pure rolling case, and the influence on oil film building can be neglected. A simple analytic model of the main bearing motion was also developed and demonstrated similar displacement and velocity characteristics.

17 WIND ENERGY↗
DOE OSTI2021

Investigation of Main Bearing Operating Conditions in a Three-Point Mount Wind Turbine Drivetrain

Wear related failures of spherical roller bearings in the main bearing position of three-point mount wind turbines have been higher than expected and can contribute to higher than anticipated operation-and-maintenance costs. In this paper, the operational conditions of such a main bearing, including measured axial displacement and velocity subject to the estimated axial loads are described for an instrumented, commercial wind turbine. The field measurements suggest a maximum axial speed between the bearing rings that is less than 2 millimeters per second. It is estimated that the axial speed between the ring and rollers is approximately 25% of this value. When compared to a speed of rolling from approximately 200-352 millimeters per second, the measured axial sliding is therefore significantly less than 1% of the speed of rolling. Previous numerical studies of lubricant film formation in rolling contacts have shown that the effect of axial sliding starts to be noticeable only when this ratio exceeds 10%; therefore, the axial velocity represents only a small disturbance to the nominal pure rolling case, and the influence on oil film building can be neglected. A simple analytic model of the main bearing motion was also developed and demonstrated similar displacement and velocity characteristics.

49 EE - Wind and Water Power Program - Wind (EE-4W↗
DOE OSTI2020

Comparing energy and water use of aqueous and gas-based metalworking fluids

Gas-based metalworking fluids (MWFs) have been proposed as alternative coolants and lubricants in machining operations to mitigate concerns surrounding water use and pollution, industrial hygiene, occupational health, and performance limitations associated with water-based (aqueous) MWFs that are ubiquitously used in the metals manufacturing industry. This study compares the primary energy and water use associated with the consumptive use, delivery, and disposal of aqueous MWFs with three gas-based MWFs in the literature-minimum quantity lubricant-in-compressed air (MQL), liquid/gaseous N-2, and liquid/supercritical CO2. The comparison accounts for reported differences in machining performance in peer-reviewed experimental studies across several machining processes and materials. The analysis shows that despite the reported improvement in tool life with N-2 and CO2-based MWFs, the electricity- and water-intensive separation and purification processes for N-2 and CO2 lead to their higher primary energy and water use per volume of material machined relative to water-based MWFs. Although MQL is found to have lower primary energy use, significant consumptive water use associated with the vegetable oil commonly used with this MWF leads to higher overall water use than aqueous MWF, which is operated in a recirculative system. Gas-based MWFs thus shift the water use upstream of the manufacturing plant. Primary energy and water use of gas-based MWFs could be reduced by focusing on achieving higher material removal rates and throughput compared to aqueous MWF instead of solely targeting improvements in tool life. Additionally, the consumptive use of CO2 and N-2 MWFs could be minimized by optimizing their flow rates and delivery to precisely meet the cooling and lubrication needs of specific machining processes instead of flooding the tool and workpiece with these gases. This article met the requirements for a gold-gold JIE data openness badge described at http://jie.click/badges.

cutting fluids↗