Search NASA⌕ Search

SEARCH · Search NASA

Results for “LUBRICATION - FRICTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Lubrication of 35-millimeter-bore ball bearings of several designs to 2.5 million DN

Parametric tests were conducted with 35mm bore, angular contact ball bearings with either a single or double outer and guided cage. The bearings were either lubricated by oil jets or employed inner ring lubrication. Outer ring cooling was added in selected tests. Lubricant flow to the bearing ranged from 300 to 1900 cc/min. All bearings were successfully run at speeds to 2.5 million DN. Increasing the lubricant flow decreased bearing ring temperatures but increased bearing power lines. The power loss and race temperatures of a jet lubricated with double outer land guided cage were always higher than those of the single land guided design at similar test conditions. The lowest bearing operating temperatures were achieved when inner ring lubrication and outer ring cooling were combined. It is found that cage slip of a double outer land guided cage is approximately twice that of a single outer land guided cage.

Schuller, F. T.↗
NASA NTRS1984

Elastohydrodynamic Lubrication. Status of Understanding

The development of elastohydrodynamic lubrication can be divided into three main stages. The first stage is the development of the idealized form of elastohydrodynamic lubrication, namely where the surfaces are smooth, the fluid behavior is assumed to be Newtonian, and isothermal considerations are assumed. Results based on these assumptions are presented for the complete spectrum of contact geometries (rectangular and elliptical), contact materials (hard and soft), and lubricant availability (fully flooded and starved). The status of understanding for the idealized stage of elastohydrodynamic lubrication is fairly well covered in the existing literature. The second stage of development separately incorporates the effects of a non-Newtonian fluid model, thermal effects, and surface roughness effects into the elastohydrodynamic lubrication model developed in stage 1. Results showing recent developments in this stage are presented. The third stage collectively considers the items considered in stage 2 in investigating the lubrication of real surfaces in their operating environments.

Bernard J Hamrock↗
NASA NTRS1989

Evaluation of newly formulated Dow Corning 321 dry film lubricant

An evaluation of the newly formulated Dow Corning 321 dry film lubricant was performed. The purpose of the evaluation was to compare lubricating characteristics of Dow Corning 321 (STW4-2955, SCN No. 3) to those of Molykote 321R (STW4-2955). Ten igniter bolts were installed and torqued on test plates using the old formulation thread lubricant (Molykote 321R), and 10 bolts were installed using the new formulation (Dow Corning 321). After bolt removal, no signs of galling were found on any of the bolts or test plates threaded holes. Average torque-load values for each formulation were very close. Test results showed there are no significant differences in lubrication abilities between Molykote 321R and Dow Corning 321. It is recommended that, once current supplies of Molykote 321R are depleted, Dow Corning 321 dry film lubricant be used in place of Molykote 321R as a thread lubricant on redesigned solid rocket motor assemblies.

Cook, M.↗
NASA NTRS1993

Equations For Elastohydrodynamic Lubrication Of Bearings

Equation for thickness of elastohydrodynamic (EHD) lubricant film in rolling-element bearing reduced to simplified form involving only inside and outside diameters of bearing, speed of rotation, parameter related to type of lubricant, and viscosity of lubricant at temperature of bearing. In addition, experimentally derived graph of EHD-film-thickness-reduction factor as function of contact-lubricant-flow number. Accounts for lubricant starvation within Hertzian contact. Graph relating ratio of minimum film thickness to composite roughness of bearing surfaces and to lubrication-life correction factor also provided. Life-correction factor used to determine resultant life of bearing.

Zaretsky, Erwin V.↗
NASA NTRS1995

Lubrication of Space Systems (c)

This article presents an overview of the current state-of-the-art tribology, some current and future perceived space lubrication problem areas, and some potential new lubrication technologies. It is the author's opinion that tribology technology, in general, has not significantly advanced over the last 20 to 30 years, even though some incremental improvements in the technology have occurred. There is a better understanding of elasto-hydrodynamic lubrication, some new lubricating and wear theories have been developed, and some new liquid and solid lubricants have been formulated. However, the important problems of being able to lubricate reliably at high temperatures or at cryogenic temperatures have not been adequately address.

Fusaro, Robert L.↗
NASA NTRS2002

In-situ, On-demand Lubrication System for Space Mechanisms

Many of today's spacecraft have long mission lifetimes. Whatever the lubrication method selected, the initial lubricant charge is required to last the entire mission. Fluid lubricant losses are mainly due to evaporation, tribo-degradation, and oil creep out of the tribological regions. In the past, several techniques were developed to maintain the appropriate amount of oil in the system. They were based on oil reservoirs (cartridges, impregnated porous parts), barrier films, and labyrinth seals. Nevertheless, all these systems have had limited success or have not established a proven record for space missions. The system reported here provides to the ball-race contact fresh lubricant in-situ and on demand. The lubricant is stored in a porous cartridge attached to the inner or the outer ring of a ball bearing. The oil is released by heating the cartridge to eject oil, taking advantage of the greater thermal expansion of the oil compared to the porous network. The heating may be activated by torque increases that signal the depletion of oil in the contact. The low surface tension of the oil compared to the ball bearing material is utilized and the close proximity of the cartridge to the moving balls allows the lubricant to reach the ball-race contacts. This oil resupply system can be used to avoid a mechanism failure or reduce torque to an acceptable level and extend the life of the component.

Marchetti, Mario↗
NASA NTRS1998

Ion Implantation of Perfluoropolyether-Lubricated Surfaces for Improved Tribological Performance

For over 30 years, perfluoropolyethers (PFPE's) have been the liquid lubricants of choice for space applications because of their proven tribological performance and desirable properties, such as low vapor pressure and a wide liquid temperature range. These oils are used in such space mechanisms as gyroscopes, scanning mirrors, actuators, and filter wheels. In the past few years, there have been several incidents during which PFPE-lubricated space mechanisms have shown anomalous behavior. These anomalies are thought to be the result of PFPE degradation. Investigative research focused on understanding and modeling the degradation of PFPE lubricants has shown that PFPE's degrade and lose their desirable properties while under boundary-lubricated, sliding/rolling contacts and at elevated temperatures. These performance deficiencies are strongly dependent on the surface chemistry and reactivity of the lubricated contacts, which dictate the formation of harmful catalytic by-products. One way to inhibit tribo-induced degradation may be to use passivated surfaces that do not promote the formation of harmful by-products. Such a passivated surface would inhibit PFPE degradation and increase the lifetime of the lubricated mechanism. Ion implantation is one such passivation technique. This surface-treatment technique can modify the surface properties of materials without affecting either the properties or dimensions of the bulk material beneath the treated layer. By introducing a foreign species into a submicron surface layer, ion implantation can induce unique surface microstructures.

Shogrin, Brad↗
NASA NTRS2016

Pulsed Plasma Lubrication Device and Method

Disclosed herein is a lubrication device comprising a solid lubricant disposed between and in contact with a first electrode and a second electrode dimensioned and arranged such that application of an electric potential between the first electrode and the second electrode sufficient to produce an electric arc between the first electrode and the second electrode to produce a plasma in an ambient atmosphere at an ambient pressure which vaporizes at least a portion of the solid lubricant to produce a vapor stream comprising the solid lubricant. Methods to lubricate a surface utilizing the lubrication device in-situ are also disclosed.

Hofer, Richard R.↗
NASA NTRS1950

Rise of Air Bubbles in Aircraft Lubricating Oils

Lubricating and antifoaming additives in aircraft lubricating oils may impede the escape of small bubbles from the oil by forming shells of liquid with a quasi-solid or gel structure around the bubbles. The rates of rise of small air bubbles, up to 2 millimeters in diameter, were measured at room temperature in an undoped oil, in the same oil containing foam inhibitors, and in an oil containing lubricating additives. The apparent diameter of the air bubbles was measured visually through an ocular micrometer on a traveling telescope. The bubbles in the undoped oil obeyed Stokes' Law, the rate of rise being proportional to the square of the apparent diameter and inversely proportional to the viscosity of the oil. The bubbles in the oils containing lubricating additives or foam inhibitors rose more slowly than the rate predicted by Stokes 1 Law from the apparent diameter, and the rate of rise decreased as the length of path the bubbles traveled increased. A method is derived to calculate the thickness of the liquid shell which would have to move with the bubbles in the doped oils to account for the abnoi'I!l8.lly slow velocity. The maximum thickness of this shell, calculated from the velocities observed, was equal to the bubble radius.

LUBRICATING OILS - FOAMING↗
NASA NTRS1971

The pressure and deformation profile between two colliding lubricated cylinders

The pressure and deformation profiles between two colliding lubricated cylinders are obtained by solving the coupled, time-dependent elastohydrodynamic equations with an iterative procedure. The analysis includes effects which were not considered in a previous solution, namely, the effect of the lubricant compressibility and the effect of a lubricant with composite pressure-viscosity coefficients. It is found that the local approach velocity plays an important role during final stages of normal approach. It causes the lubricant to be entrapped within the contact region; neither the pressure nor the deformation profile converges to the Hertzian profile for a dry contact. The use of a smaller pressure-viscosity coefficient at high pressures reduces the sharp pressure gradient at the center of the contact and produces a much milder variation of load with respect to the film thickness. The effect of compressibility of the lubricant is found to be relatively small.

Lee, K.↗
NASA NTRS1973

KSC lubricant testing program

A program was conducted to evaluate the performance of various lubricants in use and considered for use at Kennedy Space Center (KSC). The overall objectives of the program were to: (1) determine the lubrication characteristics and relative corrosion resistance of lubricants in use and proposed for use at KSC; (2) identify materials which may be equivalent to or better than KELF-90 and Krytox 240 AC greases; and (3) identify or develop an improved lubricating oil suitable for use in liquid oxygen (LOX) pumps at KSC. It was concluded that: (1) earth gel thickened greases are very poor corrosion preventive materials in the KSC environment; (2) Halocarbon 25-5S and Braycote 656 were suitable substiutes for KELF-90 and Krytox 240 AC respectively; and (3) none of the oils evaluated possessed the necessary inertness, lubricity, and corrosion prevention characteristics for the KSC LOX pumping systems in their present configuration.

Lockhart, B. J.↗
NASA NTRS1973

Microfog lubricant application system for advanced turbine engine components, phase 3

The wetting characteristics and deposit forming tendencies of a series of lubricants were evaluated using a microfog jet delivery system to wet a flat heated rotating disc. The performances of the nine lubricants are discussed in terms of the various testing parameters which include temperature, disc speed and lubricant gas flow rates. Also discussed are the heat transfer characteristics of two of the lubricants on that same plane disc specimen. The wetting characteristics and heat transfer characteristics of one of the lubricants on a complex disc simulating bearing geometry are also discussed.

Petrucco, R. J.↗
NASA NTRS1974

Asperity lubrication and cavitation in face seals

The basic aspect of parallel-surface lubrication that distinguishes it from other areas of lubrication technology is that classical lubrication theory does not predict the existence of a stable hydrodynamic film for steady-state, isothermal, incompressible flow between smooth, parallel surfaces. Hydrodynamic films between apparently parallel surfaces have been observed in practice and are often essential for the reliable performance of thrust bearings and seals. In order to account for this fortunate discrepancy between classical theory and experiment, load-support mechanisms relating to accidential features characteristic of seal performance, which relax one or more of the assumptions in the classical theory and permit the theoretical prediction of load support are proposed. Some of the features that have been analyzed are vibratory effects such as wobble and bounce, surface waviness, nonsymmetric rotation resulting from various types of misalignment, lubricant density change, non-Newtonian lubricant effects, and surface roughness.

Walowitt, J. A.↗
NASA NTRS1974

A self-lubricating bearing

An improved bearing structure is described which includes a permanently magnetized porous body filled with an interstitial magnetic lubricant for extending the operational life of self-lubricating bearings. The bearing structure is characterized by a permanently magnetized retainer formed of a porous material and filled with an interstitial magnetic lubricant, whereby the pores serve as lubricant reservoirs from which the lubricant continuously is delivered to a film disposed between contiguous bearing surfaces.

Whitaker, A. F.↗
NASA NTRS1976

Rolling-element fatigue lives of AISI 52100 steel balls with several synthetic lubricants

Rolling-element fatigue tests were run with three synthetic lubricants with and without antiwear additives and with a paraffinic mineral oil at race temperatures of 336 to 353 K (146 146 to 175 F). The five-ball fatigue tester was used with steel balls to evaluate the relative fatigue lives with each of six lubricant-additive combinations. The tests were run at 5,520 MPa (800,000psi) maximum Hertz stress, 10,000 rpm shaft speed, and 30 deg contact angle. The lubricants tested have similar kinetic viscosities at 372 K (210 F) ranging from 0.034 to 0.089 sq cm/sec (3.4 to 8.9 cS). At these conditions, the mode of failure in the five-ball fatigue tester was classical subsurface rolling-element fatigue. The baseline for comparison of fatigue life was the paraffinic mineral oil without additives. The effects of the synthetic lubricants and their additives, which are useful for boundary lubrication, oxidation or foam inhibition, were evaluated.

Parker, R. J.↗
NASA NTRS1977

Design considerations in mechanical face seals for improved performance. 2: Lubrication

The importance of sealing technology in our industrial, chemical-oriented society in regard to maintenance and environmental contamination is pointed out. It is stated that seal performance (leakage, life) is directly related to seal lubrication. Current thinking in regard to seal lubrication is reviewed; the effect of energy dissipation in the thin lubricating film separating the sealing faces is pointed out, and the results of vaporization due to heating are illustrated. Also, hydrodynamic lubrication is reviewed, and an inherent tendency for the seal to operate with angular misalignment is shown. Recent work on hydrostatic effects is summarized and the conditions for seal instability are discussed. Four different modes of seal lubrication are postulated with the mode type being a strong function of speed and pressure.

Ludwig, L. P.↗
NASA NTRS1976

Oil-air mist lubrication for helicopter gearing

The applicability of a once-through oil mist system to the lubrication of helicopter spur gears was investigated and compared to conventional jet spray lubrication. In the mist lubrication mode, cooling air was supplied at 366K (200 F) to the out of mesh location of the gear sets. The mist air was also supplied at 366K (200 F) to the radial position mist nozzle at a constant rate of 0.0632 mol/s (3 SCFM) per nozzle. The lubricant contained in the mist air varied between 32 - 44 cc/hour. In the recirculating jet spray mode, the flow rate was varied between 1893 - 2650 cc/hour. Visual inspection revealed the jet spray mode produced a superior surface finish on the gear teeth but a thermal energy survey showed a 15 - 20% increase in heat generated. The gear tooth condition in the mist lubrication mode system could be improved if the cooling air and lubricant/air flow ratio were increased. The test gearbox and the procedure used are described.

Mcgrogan, F.↗
NASA NTRS1977

Design considerations in mechanical face seals for improved performance. II - Lubrication

The importance of sealing technology in the U.S. industrial chemical-orientated society in regard to maintenance and environmental contamination is pointed out. It is stated that seal performance (leakage, life) is directly related to seal lubrication, which is a mechanism not well understood. Current thinking in regard to seal lubrication is reviewed, the effect of energy dissipation in the thin lubricating film separating the sealing faces is pointed out, and the results of vaporization due to heating are illustrated. Also, hydrodynamic lubrication is reviewed, and an inherent tendency for the seal to operate with angular misalignment is pointed out. Recent work on hydrostatic effects is summarized and the conditions for seal instability are discussed. Four different modes of seal lubrication are postulated with the mode type being a strong function of speed and pressure.

Ludwig, L. P.↗