Search NASA⌕ Search

SEARCH · Search NASA

Results for “Laminar Flow Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

User guide for STRMLN: A boundary-layer program for contoured wind-tunnel liner design

A 2-D boundary layer computer code developed to process data for an arbitrary number of streamlines is presented. Provisions are included for the computer code to determine either mass transfer rates necessary for an effective boundary layer displacement of zero thickness or the effective displacement thickness for a specified mass transfer-rate distribution. The computer code was developed to be compatible with other computer codes which are being modified and/or developed at the NASA-Langley Research Center in order to design the three dimensional, contoured, wind tunnel liner used in transonic testing of a laminar flow control system installed on a supercritical airfoil section. A brief discription of the liner design procedure, representative liner calculations, adaptive-wall design for a two dimensional wind tunnel test, and other applications are reported.

Anderson, E. C.↗
NASA NTRS1986

Potential influences of heavy rain on general aviation airplane performance

Recent NASA wind tunnel tests of airfoils in a simulated rain environment under extremely heavy rain conditions have shown reductions in maximum lift and increases in drag. Conventional airfoils were tested with and without high lift devices and tests of laminar-flow airfoils without high-lift devices were conducted. Both types of airfoils indicated performance decrements when exposed to a simulated heavy rain environment. For the laminar flow airfoil, the rain influence was observed to occur throughout the angle of attack range, whereas for the conventional airfoil in a high lift configuration, the rain influence occurred mostly at the higher angles of attack. The performance decrement for the laminar-flow airfoil appeared to be a result of laminar-to-turbulent boundary-layer transition whereas the performance penalty for the conventional airfoil appeared to be the result of premature separation. The results of these tests are presented and the implication of the results to general aviation airplanes are discussed.

Dunham, R. E., Jr.↗
NASA NTRS1987

Flight survey of the 757 wing noise field and its effects on laminar boundary layer transition. Volume 1: Program description and data analysis

It was previously observed that an incident acoustic field on a wing with laminar flow can cause transition to turbulent flow if the fluctuating acoustic velocities are of sufficient amplitude and in the critical frequency range for an unstable laminar boundary layer. A section of a wing was modified with a natural laminar flow (NLF) glove to allow direct measurement of the effect of varying engine noise on the extent of laminar flow. The flight test program was completed in June, 1985. At each flight condition, the engine power was varied from about 2600 r/min (idle) to about 4500 r/min (maximum continuous power). The spectral data provides considerable insight into the influences of the various sound sources that contribute to the overall noise levels. Additional analysis will be required to assess the impact of these sources on boundary layer transition. These results demonstrate that substantial laminar flow on the wing of a transport configuration with wing-mounted engines can be obtained.

Source record↗
NASA NTRS2004

RTO Technical Publications: A Quarterly Listing

The titles of five reports are listed here, together with an abstract for each. The titles include: 1) 'Spectral Models of Kuiper Belt Objects and Centaurs'; 2) 'Simulation of and for Military Decision Making'; 3) 'Abundance of the Radioactive Be-10 in the Cosmic Radiation up to 2 GeV/nucleon with the Balloon-borne Instrument ISOMAX1998'; 4) 'Optical Air Flow Measurements in Flight'; 5) 'Flight Test Measurement Techniques for Laminar Flow'.

Source record↗
NASA NTRS1986

Flight experiences with laminar flow

A review of natural laminar flow (NLF) flight experiences over the period from the 1930's to the present has been given to provide information on the achievability and maintainability of NLF in typical airplane operating environments. Significant effects of loss of laminar flow on airplane performance have been observed for several airplanes, indicating the importance of providing information on these changes to laminar flow airplane operators. Significant changes in airplane stability and control and maximum lift were observed in flight experiments with the loss of laminar flow. However, these effects can be avoided by proper selection of airfoils. Conservative laminar flow airfoil designs should be employed which do not experience significant loss of lift (caused by flow separation) upon the loss of laminar flow. Mechanisms have been observed for the effects of insect accumulation, flight through clouds and precipitation, and propeller slipstreams on laminar flow behavior. Fixed transition testing, in addition to free transition testing, is recommended as a new standard procedure for airplanes with surfaces designed to support laminar flow.

Holmes, Bruce J.↗
NASA NTRS1992

Status of F16XL SSLFC numerical design validation

The viewgraphs and discussion of the status of the F-16XL SSLFC numerical design validation are provided. The F-16XL Supersonic Laminar Flow Control Program (SSLFC) is a joint effort involving Rockwell's North American Aircraft Division, NASA Ames-Dryden Flight Research Facility, and NASA Langley Research Center. The objectives of the program are to demonstrate that laminar flow can be obtained on a highly swept wing at supersonic speeds, validate the capabilities of a numerical methodology designed to predict boundary layer transition, and validate the capabilities of the methodology in the design of active and passive laminar flow control (LFC) concepts. The F-16XL SSLFC Program consists of the design, fabrication, installation, and flight test of an active laminar flow control glove for the F-16XL. The glove design emphasized the active (suction) control of attachment line and crossflow boundary condition instabilities. The glove design envelop was constrained by the existing geometry, safety of flight considerations, and space requirements for the suction mechanism. The leading edge extension of the glove was limited to 10 inches for consideration of asymmetric flying qualities and the glove height above the existing surface restricted to two inches. The active (suction) portion of the wing extends to nominally 25 percent chord. The glove was constructed of a micro-perforated titanium sheet (hole diameter = 0.025 inches, spacing ratio = 1/8, and sheet thickness = 0.0025 inches). The glove design includes 22 separate chambers to allow suction variation in the chordwise direction. The F-16XL SSLFC program is currently in the flight test phase.

George, Mike↗
NASA NTRS2005

Laminar Heating Validation of the OVERFLOW Code

OVERFLOW, a structured finite difference code, was applied to the solution of hypersonic laminar flow over several configurations assuming perfect gas chemistry. By testing OVERFLOW's capabilities over several configurations encompassing a variety of flow physics a validated laminar heating was produced. Configurations tested were a flat plate at 0 degrees incidence, a sphere, a compression ramp, and the X-38 re-entry vehicle. This variety of test cases shows the ability of the code to predict boundary layer flow, stagnation heating, laminar separation with re-attachment heating, and complex flow over a three-dimensional body. In addition, grid resolutions studies were done to give recommendations for the correct number of off-body points to be applied to generic problems and for wall-spacing values to capture heat transfer and skin friction. Numerical results show good comparison to the test data for all the configurations.

Lillard, Randolph P.↗
NASA NTRS1984

Natural laminar flow flight experiments on a swept-wing business jet

Flight test experiments have been conducted to measure the extent and nature of laminar flow on a smoothed test region of a swept-wing business jet. Surface hot film anemometers and sublimating chemicals were used for transition detection. Surface pressure distributions were measured using pressure belts. Instrumentation techniques and problems are presented. Correlation was obtained between the hot film and sublimating chemicals for transition detection. Taylor-Goertler vortices were observed for some flight conditions. Boundary layer stability analysis is being conducted using measured pressure distributions to determine the correlation possible for transition prediction on swept wings.

Wentz, W. H., Jr.↗
NASA NTRS1949

Aerodynamic Study of a Wing-fuselage Combination Employing a Wing Swept Back 63 Degrees : Characteristics at a Mach Number of 1.53 Including Effect of Small Variations of Sweep

Measured values of lift, drag, and pitching moment at a Mach number of 1.53 and Reynolds numbers of 0.31, 0.62, and 0.84 million are presented for a wing-fuselage combination having a wing leading-edge sweep angle of 63 degrees, an aspect ratio of 3.42, a taper ratio of 0.25, and an NACA 64A006 section in the stream direction. Data are also presented for sweep angles of 57.0 degrees, 60.4 degrees, 67.0 degrees, and 69.9 degrees. The experimentally determined characteristics were less favorable than indicated by the linear theory but the experimental and theoretical trends with sweep were in good agreement. Boundary-layer-flow tests showed that laminar boundary-layer separation was the primary cause of the differences between experiment and theory.

REYNOLDS NUMBER EFFECTS - COMPLETE WING↗
NASA NTRS1995

Computations of Axisymmetric Flows in Hypersonic Shock Tubes

A time-accurate two-dimensional fluid code is used to compute test times in shock tubes operated at supersonic speeds. Unlike previous studies, this investigation resolves the finer temporal details of the shock-tube flow by making use of modern supercomputers and state-of-the-art computational fluid dynamic solution techniques. The code, besides solving the time-dependent fluid equations, also accounts for the finite rate chemistry in the hypersonic environment. The flowfield solutions are used to estimate relevant shock-tube parameters for laminar flow, such as test times, and to predict density and velocity profiles. Boundary-layer parameters such as bar-delta(sub u), bar-delta(sup *), and bar-tau(sub w), and test time parameters such as bar-tau and particle time of flight t(sub f), are computed and compared with those evaluated by using Mirels' correlations. This article then discusses in detail the effects of flow nonuniformities on particle time-of-flight behind the normal shock and, consequently, on the interpretation of shock-tube data. This article concludes that for accurate interpretation of shock-tube data, a detailed analysis of flowfield parameters, using a computer code such as used in this study, must be performed.

Sharma, Surendra P.↗
NASA NTRS1986

Flight research on natural laminar flow nacelles - A progress report

This paper presents a progress report on an ongoing flight experiment for natural laminar flow nacelles. The results given herein were obtained during the first phase of the experiment, in which an instrumented natural laminar flow nacelle fairing was flight tested in the presence of turbofan engine noise and a controlled noise source. The results indicate that with the controlled noise source off, natural laminar flow was measured as far aft as 37 percent of the fairing length. The transition front was irregular in contour, and the extent of natural laminar flow was significantly affected by the relative flow angle for the fairing. In addition to these test results, the paper discusses the results of some recent computational analyses to predict pressure distributions and transition location, and to explain some of the data trends. Comparisons between measured and predicted data indicate that the analytical methods successfully predicted trends for the baseline (no controlled noise source) studies.

Hastings, E. C., Jr.↗
NASA NTRS1987

Wind tunnel results of the high-speed NLF(1)-0213 airfoil

Wind tunnel tests were conducted to evaluate a natural laminar flow airfoil designed for the high speed jet aircraft in general aviation. The airfoil, designated as the High Speed Natural Laminar Flow (HSNLF)(1)-0213, was tested in two dimensional wind tunnels to investigate the performance of the basic airfoil shape. A three dimensional wing designed with this airfoil and a high lift flap system is also being evaluated with a full size, half span model.

Sewall, William G.↗
NASA NTRS2024

Experimental and Computational Study of Convective Heating on the Aeroshell Back Side and Payload of the LOFTID Vehicle

A wind tunnel test program was conducted to obtain experimental convective heating data on models of the Low Earth Orbital Flight Test of an Inflatable Decelerator (LOFTID) vehicle in support of the flight test program. Wind tunnel testing was conducted at Mach 6 and Mach 10 at unit Reynolds numbers from 0.5×106/ft to 4.0×106/ft on 6.0inch diameter aeroshell models. Global heating data were obtained through phosphor thermography measurements on the front and back of the aeroshell and on the payload. For all test conditions, attached, laminar flow was definitively produced on the front of the aeroshell, while in the wake the flow was separated, unsteady and possibly transitional or turbulent. A complementary computational study was performed to assess the accuracy of heating predictions for LOFTID wake flow environments. A new grid topology was developed for the study to allow the use of structured grid solvers for complex, open-backed geometries such as that of LOFTID. Close agreement between measurements and predictions was obtained on the front of the aeroshell. Comparisons were more challenging in the wake because of both the extremely low heating rates and the accompanying high uncertainties and the unsteady nature of the separated wake flow simulations. While the differences between heating predictions and measurements for the wake flow were higher than for the forebody flow, these differences were used to assist in the definition of conservative uncertainty margins for predictions of the flight environments for the successful flight test of the LOFTID vehicle in November 2022.

LOFTID↗
NASA NTRS1958

Boundary-Layer-Transition Measurements in Full-Scale Flight

Chemical sublimation has been employed for boundary-layer-flow visualization on the wings of a supersonic fighter airplane in level flight at speeds near a Mach number of 2.0. The tests have shown that laminar flow can be obtained over extensive areas of the wing with practical wing-surface conditions. In addition to the flow visualization tests, a method of continuously monitoring the conditions of the boundary layer has been applied to flight testing, using heated temperature resistance gages installed in a Fiberglas "glove" installation on one wing. Tests were conducted at speeds from a Mach number of 1.2 to a Mach number of 2.0, at altitudes from 35,000 feet to 56,000 feet. Data obtained at all angles of attack, from near 0 deg to near 10 deg, have shown that the maximum transition Reynolds number on the upper surface of the wing varies from about 2.5 x 10(exp 6) at a Mach number of 1.2 to about 4 x 10(exp 6) at a Mach number of 2.0. On the lower surface, the maximum transition Reynolds number varies from about 2 x 10(exp 6) at a Mach number of 1.2 to about 8 x 10(exp 6) at a Mach number of 2.0.

SUPERSONIC FLOW↗
NASA NTRS1985

On the accuracy of the pseudocompressibility method in solving the incompressible Navier-Stokes equations

The method of pseudocompressibility is being tested for its accuracy in solving the incompressible Navier-Stokes equations. An implicit, finite-difference computer code is used to solve the equations in a three-dimensional, curvilinear coordinate system. The code employs artificial compressibility for solving the pressure field, coupled with an implicit, approximate-factorization scheme. This coupling is known as the pseudocompressibility method. The pseudocompressibility method introduces pressure waves of finite speed into the fluid medium that would otherwise have an infinite sound speed. The waves die out as the solution converges, and the steady state solution approaches a divergence-free condition. However, these waves limit the time-accuracy of the computations. The effects of these waves are analyzed and criteria are set for choosing the pseudocompressibility parameters that govern the pressure wave speed. Test cases are presented that verify these criteria. The code is tested by computing laminar flow over a two-dimensional, backward-facing step and over a two-dimensional, impulsively started circular cylinder.

Rogers, S. E.↗
NASA NTRS1986

Natural laminar flow flight experiments on a swept wing business jet-boundary layer stability analyses

The linear boundary layer stability analyses and their correlation with data of 18 cases from a natural laminar flow (NLF) flight test program using a Cessna Citation 3 business jet are described. The transition point varied from 5% to 35% chord for these conditions, and both upper and lower wing surfaces were included. Altitude varied from 10,000 to 43,000 ft and Mach number from 0.3 to 0.8. Four cases were at nonzero sideslip. Although there was much scatter in the results, the analyses of boundary layer stability at the 18 conditions led to the conclusion that crossflow instability was the primary cause of transition. However, the sideslip cases did show some interaction of crossflow and Tollmien-Schlichting disturbances. The lower surface showed much lower Tollmien-Schlichting amplification at transition than the upper surface, but similar crossflow amplifications. No relationship between Mach number and disturbance amplification at transition could be found. The quality of these results is open to question from questionable wing surface quality, inadequate density of transition sensors on the wing upper surface, and an unresolved pressure shift in the wing pressure data. The results of this study show the need for careful preparation for transition experiments. Preparation should include flow analyses of the test surface, boundary layer disturbance amplification analyses, and assurance of adequate surface quality in the test area. The placement of necessary instruments and usefulness of the resulting data could largely be determined during the pretest phase.

Rozendaal, R. A.↗