SEARCH · Search NASA

Results for “Lift Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1989

A zonal method for modeling powered-lift aircraft flow fields

A zonal method for modeling powered-lift aircraft flow fields is based on the coupling of a three-dimensional Navier-Stokes code to a potential flow code. By minimizing the extent of the viscous Navier-Stokes zones the zonal method can be a cost effective flow analysis tool. The successful coupling of the zonal solutions provides the viscous/inviscid interations that are necessary to achieve convergent and unique overall solutions. The feasibility of coupling the two vastly different codes is demonstrated. The interzone boundaries were overlapped to facilitate the passing of boundary condition information between the codes. Routines were developed to extract the normal velocity boundary conditions for the potential flow zone from the viscous zone solution. Similarly, the velocity vector direction along with the total conditions were obtained from the potential flow solution to provide boundary conditions for the Navier-Stokes solution. Studies were conducted to determine the influence of the overlap of the interzone boundaries and the convergence of the zonal solutions on the convergence of the overall solution. The zonal method was applied to a jet impingement problem to model the suckdown effect that results from the entrainment of the inviscid zone flow by the viscous zone jet. The resultant potential flow solution created a lower pressure on the base of the vehicle which produces the suckdown load. The feasibility of the zonal method was demonstrated. By enhancing the Navier-Stokes code for powered-lift flow fields and optimizing the convergence of the coupled analysis a practical flow analysis tool will result.

Roberts, D. W.↗

NASA NTRS1990

Optimal multiple-pass aeroassisted plane change

This paper presents the exact dimensionless equation of motion and the necessary conditions for the computation of the optimal trajectories of a hypervelocity vehicle flying through a non-rotating spherical planetary atmosphere. Numerical solution is then presented for the case when the vehicle makes several passages through the atmosphere near the perigee of its orbit. While the orbit is slowly contracting, aerodynamic maneuver is performed to obtain the maximum plane change. Several plots were presented to show the optimal variations of the lift coefficient and the bank angle and the various elements of the orbit.

Vinh, Nguyen X.↗

NASA NTRS1993

Interpretation of waverider performance data using computational fluid dynamics

A computational study was conducted to better understand experimental results obtained from wind tunnel tests of a Mach 4 waverider model and a comparative reference configuration. The experimental results showed that the performance of the reference configuration was slightly better than that of the waverider model. These results contradict waverider design theory, which suggests that a waverider optimized for maximum lift-to-drag should provide better performance than any other non-waverider configuration at a given design point, especially at hypersonic speeds. The computational results showed that the predicted surface pressure values and the integrated lift and drag coefficients from the pressure distributions were much lower for the reference model than for the flat-top model, due to the reference model bottom surface having a slight expansion. The lift-to-drag ratios for the flat-top model were higher due to a relatively low drag for the same amount of lift. These results indicate that the performance advantage of the reference model was due to the shape of the bottom surface and not due to the flat top surface. The results also showed that the reference model exhibited the same shock attachment characteristics as the waverider because the planform shapes were identical. CFD predictions show that the planform shape gives the waverider an advantage in performance over conventional hypersonic vehicles and that altering the bottom surface of a waverider does not cause significant performance degradation.

Cockrell, Charles E., Jr.↗

NASA NTRS2003

Numerical Simulation of One- and Two-Phase Flows in Propulsion Systems

Four subprojects were conducted using analytical methods, numerical simulation and experimental tests: (A) Shock wave mitigation by spike-shaped blunt bodies with application for the purpose of drag, lift and longitudinal momentum optimization. The main result in this subproject is: application of a single needle against a supersonic flow provides higher benefits for blunt body drag reduction and heat transfer to the body than the application of multiple needles. (B) Solid particles, liquid and air jet injection through the front of a blunt body against a supersonic flow. In this case, the research conducted and analysis of multiple previous investigations in this area have shown essential benefits and preferable application of solid particle injection. (C) Comparison of different methods of fuel injection into supersonic duct flows. Preliminary numerical simulations and theoretical analysis show promising results for Telescope-shaped inlet applications in SCRAMJET; and (D) Development of an acoustic source location method for different applications including propulsion systems.

Gilinsky, Mikhail↗

NASA NTRS2004

Application of Excitation from Multiple Locations on a Simplified High-Lift System

A series of active flow control experiments were recently conducted on a simplified high-lift system. The purpose of the experiments was to explore the prospects of eliminating all but simply hinged leading and trailing edge flaps, while controlling separation on the supercritical airfoil using multiple periodic excitation slots. Excitation was provided by three. independently controlled, self-contained, piezoelectric actuators. Low frequency excitation was generated through amplitude modulation of the high frequency carrier wave, the actuators' resonant frequencies. It was demonstrated, for the first time, that pulsed modulated signal from two neighboring slots interact favorably to increase lift. Phase sensitivity at the low frequency was measured, even though the excitation was synthesized from the high-frequency carrier wave. The measurements were performed at low Reynolds numbers and included mean and unsteady surface pressures, surface hot-films, wake pressures and particle image velocimetry. A modest (6%) increase in maximum lift (compared to the optimal baseline) was obtained due t o the activation of two of the three actuators.

Melton, LaTunia Pack↗

NASA NTRS1993

Interpretation of Waverider Performance Data Using Computational Fluid Dynamics

Cockrell, Charles E., Jr.↗

DOE OSTI2024

On optimizing the sensor spacing for pressure measurements on wind turbine airfoils

This research article presents a robust approach to optimizing the layout of pressure sensors around an airfoil. A genetic algorithm and a sequential quadratic programming algorithm are employed to derive a sensor layout best suited to represent the expected pressure distribution and, thus, the lift force. The fact that both optimization routines converge to almost identical sensor layouts suggests that an optimum exists and is reached. By comparing against a cosine-spaced sensor layout, it is demonstrated that the underlying pressure distribution can be captured more accurately with the presented layout optimization approach. Conversely, a 39 %–55 % reduction in the number of sensors compared to cosine spacing is achievable without loss in lift prediction accuracy. Given these benefits, an optimized sensor layout improves the data quality, reduces unnecessary equipment and saves cost in experimental setups. While the optimization routine is demonstrated based on the generic example of the IEA 15 MW reference wind turbine, it is suitable for a wide range of applications requiring pressure measurements around airfoils.

17 WIND ENERGY↗

NASA NTRS1991

Crescent Wing Planforms Reduce Lift-Dependent Drag

New understanding of optimization of design of wing to minimize induced drag developed by use of computational methods that account properly for nonlinear effects of deflected wake, nonplanar shape of wing, and vortex rollup. Crescent planforms are lunate shapes like some found in nature, similar to certain bird wings and fish fins. Theoretical and experimental analyses reveals superior aerodynamic efficiency and improved high-angle-of-attack characteristics.

Holmes, Bruce J.↗

NASA NTRS1998

Mechanical Design of High Lift Systems for High Aspect Ratio Swept Wings

The NASA Ames Research Center is working to develop a methodology for the optimization and design of the high lift system for future subsonic airliners with the involvement of two partners. Aerodynamic analysis methods for two dimensional and three dimensional wing performance with flaps and slats deployed are being developed through a grant with the aeronautical department of the University of California Davis, and a flap and slat mechanism design procedure is being developed through a contract with PKCR, Inc., of Seattle, WA. This report documents the work that has been completed in the contract with PKCR on mechanism design. Flap mechanism designs have been completed for seven (7) different mechanisms with a total of twelve (12) different layouts all for a common single slotted flap configuration. The seven mechanisms are as follows: Simple Hinge, Upside Down/Upright Four Bar Linkage (two layouts), Upside Down Four Bar Linkages (three versions), Airbus A330/340 Link/Track Mechanism, Airbus A320 Link/Track Mechanism (two layouts), Boeing Link/Track Mechanism (two layouts), and Boeing 767 Hinged Beam Four Bar Linkage. In addition, a single layout has been made to investigate the growth potential from a single slotted flap to a vane/main double slotted flap using the Boeing Link/Track Mechanism. All layouts show Fowler motion and gap progression of the flap from stowed to a fully deployed position, and evaluations based on spanwise continuity, fairing size and number, complexity, reliability and maintainability and weight as well as Fowler motion and gap progression are presented. For slat design, the options have been limited to mechanisms for a shallow leading edge slat. Three (3) different layouts are presented for maximum slat angles of 20 deg, 15 deg and 1O deg all mechanized with a rack and pinion drive similar to that on the Boeing 757 airplane. Based on the work of Ljungstroem in Sweden, this type of slat design appears to shift the lift curve so that higher lift is achieved with the deployed slat with no increase in angle of attack. The layouts demonstrate that these slat systems can be designed with no need for slave links, and an experimental test program is outlined to experimentally validate the lift characteristics of the shallow slat.

Rudolph, Peter K. C.↗

NASA NTRS1991

Evaluation of tunnel sidewall boundary-layer-control systems for high-lift airfoil testing

An experimental study was conducted in the NASA Langley Low-Turbulence Pressure Tunnel to evaluate a suction sidewall boundary-layer-control (BLC) technique used in testing 2D high-lift airfoils. Sidewall BLC is required to maintain spanwise two-dimensionality of the flow over the airfoil at large angles of attack. A supercritical-type high-lift air-foil, equipped with a double-slotted flap and a leading-edge slat, was used for the study which was conducted at a Mach number of 0.2 and Reynolds numbers based on chord of 9 and 16 million. The sidewall BLC technique, which features distributed suction through porous endplates connected to a venting system, was able to control sidewall boundary-layer separation and maintain two-dimensional flow over the high-lift configuration for both Reynolds numbers tested. Discussions on porous endplate optimization and effects of suction on section lift are presented. Results obtained with the suction system were also compared with previous data obtained with a tangential blowing BLC system for the same high-lift configuration.

Paschal, K.↗

NASA NTRS1980

High density circuit technology

Acquisition of polyimide materials for inter-metal dielectrics was obtained from three vendors, with considerable evaluation conducted on the Dupont PI2550 material. Experimental results indicate this material can be patterned using contact printing to line width far below 0.1 mils. Optimum line width is acquired using plasma etch equipment. Metal lift-off experiments on thermal evaporated films were optimized for application to sputtered deposited films. Alternate metal-lift-off experiments are proposed for future investigation. Dry processing equipment studies and future trends in VLSI fabrication techniques are on-going.

Wade, T. E.↗

NASA NTRS1990

Gamma guidance of trajectories for coplanar, aeroassisted orbital transfer

The optimization and guidance of trajectories for coplaner, aeroassisted orbital transfer (AOT) from high Earth orbit (HEO) to low Earth orbit (LEO) are examined. In particular, HEO can be a geosynchronous Earth orbit (GEO). It is assumed that the initial and final orbits are circular, that the gravitational field is central and is governed by the inverse square law, and that at most three impulses are employed: one at HEO exit, one at atmospheric exit, and one at LEO entry. It is also assumed that, during the atmospheric pass, the trajectory is controlled via the lift coefficient. The presence of upper and lower bounds on the lift coefficient is considered. First, optimal trajectories are computed by minimizing the total velocity impulse (hence, the propellant consumption) required for AOT transfer. The sequential gradient-restoration algorithm (SGRA) is used for optimal control problems. The optimal trajectory is shown to include two branches: a relatively short descending flight branch (branch 1) and a long ascending flight branch (branch 2). Next, attention is focused on guidance trajectories capable of approximating the optimal trajectories in real time, while retaining the essential characteristics of simplicity, ease of implementation, and reliability. For the atmospheric pass, a feedback control scheme is employed and the lift coefficient is adjusted according to a two-stage gamma guidance law. Further improvements are possible via a modified gamma guidance which is more stable with respect to dispersion effects arising from navigation errors, variations of the atmospheric density, and uncertainties in the aerodynamic coefficients than gamma guidance trajectory. A byproduct of the studies on dispersion effects is the following design concept. For coplaner aeroassisted orbital transfer, the lift-range-to-weight ratio appears to play a more important role than the lift-to-drag ratio. This is because the lift-range-to-weight ratio controls mainly the minimum altitude (hence, the peak heating rate) of the guidance trajectory; on the other hand, the lift-to-drag ratio controls mainly the duration of the atmospheric pass of the guidance trajectory.

Miele, A.↗

NASA NTRS1985

Aerothermodynamic Heating Analysis of Aerobraking and Aeromaneuvering Orbital Transfer Vehicles

The thermal-protection requirements of two aeroassisted orbital transfer vehicles (AOTVS) are analyzed for return missions between the geosynchronous and Shuttle orbits. One of the designs is a specialized version of a previously proposed generic aerobraking vehicle that Is capable of only delivery-type operations. The other Is a high-lift aeromaneuvering vehicle that is optimized for low Earth orbit sortie missions involving large, multiple plane-inclination changes. The aerothermal environment of the aerobraking vehicle is analyzed using state-of-the-art methods for nonequilibrium-radiative and convective heating that incorporate refinements unique to the configuration. The heating analysis of the aeromaneuvering vehicle required the development of a flowfield model for rarefied-hypersonic flow over a lifting surface at incidence. The predicted aerothermodynamic heating characteristics for both vehicles are correlated with thermal-control

Menees, Gene P.↗

NASA NTRS1984

Aerothermodynamic heating analysis of aerobraking and aeromaneuvering orbital-transfer vehicles

The thermal-protection requirements of two aeroassisted orbital-transfer vehicles (AOTVs) are analyzed for return missions between the geosynchronous and Shuttle orbits. One of the designs is a specialized version of a previously proposed generic aerobraking vehicle that is capable of only delivery-type operations. The other is a high-lift aeromaneuvering vehicle that is optimized for low-earth orbit sortie missions involving large, multiple plane-inclination changes. The aerothermal environment of the aerobraking vehicle is analyzed using state-of-the-art methods for nonequilibrium-radiative and convective heating that incorporate refinements unique to the configuration. The heating analysis of the aeromaneuvering vehicle required the development of a flow-field model for rarefied-hypersonic flow over a lifting surface at incidence. The predicted aerothermodynamic heating characteristics for both vehicles are correlated with thermal-control requirements and flight performance capabilities for the specified mission guidelines. The results help identify technical issues related to the development of future operational systems.

Davies, C. B.↗

NASA NTRS1996

Application of pneumatic lift and control surface technology to advanced transport aircraft

The application of pneumatic (blown) aerodynamic technology to both the lifting and the control surfaces of advanced transport aircraft can provide revolutionary changes in the performance and operation of these vehicles, ranging in speed regime from Advanced Subsonic Transports to the High Speed Civil Transport, and beyond. This technology, much of it based on the Circulation Control Wing blown concepts, can provide aerodynamic force augmentations of 80 to 100 (i.e., return of 80-100 pounds of force per pound of input momentum from the blowing jet). This can be achieved without use of external mechanical surfaces. Clever application of this technology can provide no-moving-part lifting surfaces (wings/tails) integrated into the control system to greatly simplify aircraft designs while improving their aerodynamic performance. Lift/drag ratio may be pneumatically tailored to fit the current phase of the flight, and takeoff/landing performance can be greatly improved by reducing ground roll distances and liftoff/touchdown speeds. Alternatively, great increases in liftoff weights and payloads are possible, as are great reductions in wing and tail planform size, resulting in optimized cruise wing designs. Furthermore, lift generation independent of angle of attack provides much promise for increased safety of flight in the severe updrafts/downdrafts of microbursts and windshears, which is further augmented by the ability to sustain flight at greatly reduced airspeeds. Load-tailored blown wings can also reduce tip vorticity during highlift operations and the resulting vortex wake hazards near terminal areas. Reduced noise may also be possible as these jets can be made to operate at low pressures. The planned presentation will support the above statements through discussions of recent experimental and numerical (CFD) research and development of these advanced blown aerodynamic surfaces, portions of which have been conducted for NASA. Also to be presented will be predicted performance of advanced transports resulting from these devices. Suggestions will be presented for additional innovative high-payoff research leading to further confirmation of these concepts and their application to advanced efficient commercial transport aircraft.

Englar, Robert J.↗

NASA NTRS1992

Design tradeoffs on engine-integrated hypersonic vehicles

Two classes of airbreathing hypersonic vehicle concepts, one for primarily cruise missions and the other for accelerator type missions, are presented. Both are designed with waverider airframes and hydrogen-fueled scramjet engine modules. Cruise configurations are optimized for the product of I(sp) and L/D while matching lift to weight and thrust to drag at some equivalence ratio. Accelerator configurations are optimized for effective specific impulse while matching lift to weight at an equivalence ratio of one. The method and computer code developed to optimize the configurations are discussed. The features and design tradeoffs for each class of vehicles are described. Recently available weight estimates for all-body waveriders have had a significant impact on the integrated configurations. Mach 8 vehicles at 40 km altitude optimized with the cruise objective function have L/Ds of 2.55 to 2.92 and I(sp)s of 2850 to 2940 sec. A Mach 14 vehicle at 40-km altitude optimized with the accelerator objective function has an I(sp) sub eff of 189 sec, and a Mach 10 vehicle an I(sp) sub eff of 880 sec.

O'Neill, Mary Kae L.↗

NASA NTRS1999

The Analysis and Design of Low Boom Configurations Using CFD and Numerical Optimization Techniques

The use of computational fluid dynamics (CFD) for the analysis of sonic booms generated by aircraft has been shown to increase the accuracy and reliability of predictions. CFD takes into account important three-dimensional and nonlinear effects that are generally neglected by modified linear theory (MLT) methods. Up to the present time, CFD methods have been primarily used for analysis or prediction. Some investigators have used CFD to impact the design of low boom configurations using trial and error methods. One investigator developed a hybrid design method using a combination of Modified Linear Theory (e.g. F-functions) and CFD to provide equivalent area due to lift driven by a numerical optimizer to redesign or modify an existing configuration to achieve a shaped sonic boom signature. A three-dimensional design methodology has not yet been developed that completely uses nonlinear methods or CFD. Constrained numerical optimization techniques have existed for some time. Many of these methods use gradients to search for the minimum of a specified objective function subject to a variety of design variable bounds, linear and nonlinear constraints. Gradient based design optimization methods require the determination of the objective function gradients with respect to each of the design variables. These optimization methods are efficient and work well if the gradients can be obtained analytically. If analytical gradients are not available, the objective gradients or derivatives with respect to the design variables must be obtained numerically. To obtain numerical gradients, say, for 10 design variables, might require anywhere from 10 to 20 objective function evaluations. Typically, 5-10 global iterations of the optimizer are required to minimize the objective function. In terms of using CFD as a design optimization tool, the numerical evaluation of gradients can require anywhere from 100 to 200 CFD computations per design for only 10 design variables. If one CFD computation requires an hour of computational time on a Cray computer, one can see that the use of constrained numerical optimization quickly becomes impractical.Hence, in order to practically couple a numerical design optimization technique with a CFD method, the CFD method must be extremely efficient with running times on the order of only minutes. The CFD Euler code developed under NASA sponsorship and referred to as MIM3D-SB for the most part fulfills these efficiency requirements. Analysis of wing- body configurations can be computed in a matter of a few minutes. The present study will concentrate on the feasibility of the use of this CFD code in conjunction with a numerical design optimization technique for the sonic boom reduction of candidate HSCT configurations. A preliminary supersonic aircraft design system has been established that utilizes the numerical design optimization code NPSOL developed at Stanford University coupled with the supersonic NUM3D-SB CFD code. Many questions still need to be answered in regard to using CFD and numerical optimizers as design tools. There are difficulties related to both the CFD codes and the numerical optimizers. Numerical optimizers can converge to a local minima rather than a global minima. This behavior is largely a function of the initial guess in the design space. The optimizer also is searching for a minimum of the function in terms of its derivative without any regard to the actual function value. Numerically (i.e. CFD) determined gradients can also generate spurious numerical local minima. In addition, for the sonic boom problem, grid fineness will also determine the accuracy of the final design solution. Design optimization methods work well on problems defined by continuous objective functions. The sonic boom signature design problem is not necessarily defined by a continuous objective function. The signature can have a variety of shapes; i.e. from N-wave to multiple shocks. The far-field or ground signature may not transition continuously from one shape to another and hence, may exhibit discontinuous behavior. This is also a source of difficulty in using design optimization methods.In the following sections, several low boom and one reference aircraft configuration will be analyzed to predict their sonic boom signature characteristics. Modifications to some of these designs will also be presented to demonstrate the feasibility of using CFD as a design tool and to demonstrate the feasibility of designing shaped sonic boom signatures. Design modifications to some configurations will be presented to demonstrate the feasibility of achieving shaped signatures with reduced levels and not necessarily to represent realistic or aerodynamically efficient design modifications. Fuselage volume or camber are used as design variables in order to have a minimal effect on the primary wing aerodynamics. The paper will also seek to demonstrate whether a hybrid or ramped signature is feasible to achieve. For the low-boom configurations, the CFD predicted signatures will be compared qualitatively to their MLT design signatures.

Siclari, Michael J.↗

NASA NTRS2001

Robust Airfoil Optimization to Achieve Consistent Drag Reduction Over a Mach Range

We prove mathematically that in order to avoid point-optimization at the sampled design points for multipoint airfoil optimization, the number of design points must be greater than the number of free-design variables. To overcome point-optimization at the sampled design points, a robust airfoil optimization method (called the profile optimization method) is developed and analyzed. This optimization method aims at a consistent drag reduction over a given Mach range and has three advantages: (a) it prevents severe degradation in the off-design performance by using a smart descent direction in each optimization iteration, (b) there is no random airfoil shape distortion for any iterate it generates, and (c) it allows a designer to make a trade-off between a truly optimized airfoil and the amount of computing time consumed. For illustration purposes, we use the profile optimization method to solve a lift-constrained drag minimization problem for 2-D airfoil in Euler flow with 20 free-design variables. A comparison with other airfoil optimization methods is also included.

Li, Wu↗