Search NASA⌕ Search

SEARCH · Search NASA

Results for “MASS RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Onset of Reconnection in the near Magnetotail: PIC Simulations

Using 2.5-dimensional particle-in-cell (PIC) simulations of magnetotail dynamics, we investigate the onset of reconnection in two-dimensional tail configurations with finite Bz. Reconnection onset is preceded by a driven phase, during which magnetic flux is added to the tail at the high-latitude boundaries, followed by a relaxation phase, during which the configuration continues to respond to the driving. We found a clear distinction between stable and unstable cases, dependent on deformation amplitude and ion/electron mass ratio. The threshold appears consistent with electron tearing. The evolution prior to onset, as well as the evolution of stable cases, are largely independent of the mass ratio, governed by integral flux tube entropy conservation as imposed in MHD (magnetohydrodynamics). This suggests that ballooning instability in the tail should not be expected prior to the onset of tearing and reconnection. The onset time and other onset properties depend on the mass ratio, consistent with expectations for electron tearing. At onset,we found electron anisotropies T⊥⁄ T∥ (bottom tail divided by parallel tail) equals 1.1-1.3, raising growth rates and wavenumbers. Our simulations have provided a quantitative onset criterion that is easily evaluated in MHD simulations, provided the spatial resolution is sufficient. The evolution prior to onset and after the formation of a neutral line does not depend on the electron physics, which should permit an approximation by MHD simulations with appropriate dissipation terms.

PIC↗

Radial velocity studies and absolute parameters of contact binaries. I - AB Andromedae

New radial velocity curves have been obtained for the contact binary AB And, using the cross-correlation technique. A mass ratio of 0.479 is determined, which is revised to 0.491 when the velocities are corrected for proximity effects using a light curve model. These values differ by less than ten percent from the photometric mass ratio. An analysis of the symmetric B and V light curves reported by Rigterink in 1973 using the spectroscopic mass ratio yields a consistent set of light and velocity curve elements. These also produce a reasonably good fit to the infrared J and K light curves reported by Jameson and Akinci in 1979. Absolute elements are determined, and these indicate that both components have a main-sequence internal structure. These absolute parameters, together with the Galactic kinematics, suggest an age for the system similar to or greater than that of the Sun.

Hrivnak, Bruce J.↗

OGLE-2013-BLG-0911Lb: A Secondary on the Brown-dwarf Planet Boundary around an M Dwarf

We present the analysis of the binary-lens microlensing event OGLE-2013-BLG-0911. The best-fit solutions indicate the binary mass ratio of q 0.03, which differs from that reported in Shvartzvald et al. The event suffers from the well-known close/wide degeneracy, resulting in two groups of solutions for the projected separation normalized by the Einstein radius of s ~ 0.15 or s ~ 7. The finite source and the parallax observations allow us to measure the lens physical parameters. The lens system is an M dwarf orbited by a massive Jupiter companion at very close (M(host) = 0.30(sup +0.08, sub -0.06)Mʘ, M(comp) = 10.1 (sup +2.9, sub -2.2 M(jup), a(exp) = 0.40 (sup +0.05, sub -0.40)au) or wide (M(host) = 0.28 (sup +0.10, sub -0.80)Mʘ, M(comp) = 9.9 (sup +3.8, sub -3.5)M(jup), a(exp) = 18.0 (sup +3.2, sub -3.2)au) separation. Although the mass ratio is slightly above the planet-brown dwarf (BD) mass-ratio boundary of q = 0.03, which is generally used, the median physical mass of the companion is slightly below the planet-BD mass boundary of 13M(Jup). It is likely that the formation mechanisms for BDs and planets are different and the objects near the boundaries could have been formed by either mechanism. It is important to probe the distribution of such companions with masses of ~13M(Jup) in order to statistically constrain the formation theories for both BDs and massive planets. In particular, the microlensing method is able to probe the distribution around low-mass M dwarfs and even BDs, which is challenging for other exoplanet detection methods.

Shota Miyazaki↗

OGLE-2019-BLG-0960 Lb: the Smallest Microlensing Planet

We report the analysis of OGLE-2019-BLG-0960, which contains the smallest mass-ratio microlensing planet found to date (q = 1.2–1.6 × 10^(−5) at 1σ). Although there is substantial uncertainty in the satellite parallax measured by Spitzer, the measurement of the annual parallax effect combined with the finite source effect allows us to determine the mass of the host star (M(L) = 0.3–0.6 Mꙩ), the mass of its planet (m(p) = 1.4–3.1 Mꚛ), the projected separation between the host and planet (a(⊥) = 1.2–2.3 au), and the distance to the lens system (D(L) = 0.6–1.2 kpc). The lens is plausibly the blend, which could be checked with adaptive optics observations. As the smallest planet clearly below the break in the mass-ratio function, it demonstrates that current experiments are powerful enough to robustly measure the slope of the mass-ratio function below that break. We find that the cross-section for detecting small planets is maximized for planets with separations just outside of the boundary for resonant caustics and that sensitivity to such planets can be maximized by intensively monitoring events whenever they are magnified by a factor A > 5. Finally, an empirical investigation demonstrates that most planets showing a degeneracy between (s > 1) and (s < 1) solutions are not in the regime (|log s| ≫ 0) for which the "close"/"wide" degeneracy was derived. This investigation suggests that there is a link between the "close"/"wide" and "inner/outer" degeneracies and also that the symmetry in the lens equation goes much deeper than symmetries uncovered for the limiting cases.

Jennifer C. Yee↗

Venus cloud properties - Infrared opacity and mass mixing ratio

By using the Mariner 5 temperature profile and a homogeneous cloud model, and assuming that CO2 and cloud particles are the only opacity sources, the wavelength dependence of the Venus cloud opacity is inferred from the infrared spectrum of the planet between 450 and 1250 per cm. Volume extinction coefficients varying from 0.000005 to 0.000015 per cm, depending on the wavelength, are determined at the tropopause level of 6110 km. By using all available data, a cloud mass mixing ratio of approximately 0.000005 and a particle concentration of about 900 particles per cu cm at this level are also inferred. The derived cloud opacity compares favorably with that expected for a haze of droplets of a 75% aqueous solution of sulfuric acid.

Samuelson, R. E.↗

An investigation of several NACA 1-series inlets at Mach numbers from 0.4 to 1.29 for mass flow ratios near 1.0

An investigation to determine the performance of eight NACA 1-series inlets at massflow ratios near 1.0 was conducted in the Langley 16-foot transonic tunnel. The inlet diameter ratios (ratio of inlet diameter to maximum diameter) were 0.85 and 0.89 for an inlet length ratio (ratio of inlet length to maximum diameter) of 1.0. Inlet lip radius varied from 0.061 cm to 0.251 cm, and internal contraction area ratio (ratio of inlet area to throat area) varied from 1.006 to 1.201. Reynolds number based on model maximum diameter ranged from 3,600,000 at a Mach number of 400,000 to 5,900,000 at a Mach number of 1.29. The results indicate that nearly uniform pressure distributions on a given inlet were obtained over a limited range of mass-flow ratios and Mach numbers. When inlet lip thickness was increased by means of lip radius or contraction ratio, the inlet critical Mach number decreased. Drag-divergence Mach number inferred from forebody pressure integrations was above 0.94 for most of the inlets tested.

Re, R. J.↗

IRAS observations of a large sample of normal irregular galaxies

IRAS 12, 25, 60, and 100 micron data are presented for a sample of Irr galaxies which span a large range in star-formation activity. It is found that the dwarf, giant, and amorphous Irr's generally have similar IR properties. The typical L(IR)/L(H-alpha) ratios of most classes of Irr's, except for many of the luminous blue galaxies, are low compared with those of spiral galaxies and are consistent with the Irr's being relatively transparent systems without large amounts of optically hidden star formation. Compared with spiral galaxies, the Irr's have similar L(IR)/L(B) ratios, warmer S(100)/S(60) ratios, cooler S(25)/S(12) ratios, and lower dust-to-H I gas mass ratios. The temperature, dust-to-H I gas mass ratios, and L(IR)/L(B) ratios do not correlate with the metallicity of the ionized gas of the Irr's. A correlation between the IR fluxes and both the H-alpha and the blue stellar fluxes is found for the Irr's.

Hunter, Deidre A.↗

Venus cloud properties: Infrared opacity and mass mixing ratio

By using the Mariner 5 temperature profile and a homogeneous cloud model, and assuming that CO2 and cloud particles are the only opacity sources, the wavelength dependence of the Venus cloud opacity is inferred from the infrared spectrum of the planet between 450 and 1250/cm. Justification for applying the homogeneous cloud model is found in the fact that numerous polarization and infrared data are mutually consistent within the framework of such a model; on the other hand, dense cloud models are not satisfactory. Volume extinction coefficients varying from 0.000005 to 0.000015/cm depending on the wavelength, are determined at the tropopause level of 6110 km. By using all available data, a cloud mass mixing ratio of approximately 0.000005 and a particle concentration of about 900 particles per cu cm at this level are also inferred. The derived cloud opacity compares favorably with that expected for a haze of droplets of a 75% aqueous solution of sulfuric acid.

Samuelson, R. E.↗

Ballistic Mass And Velocity Analyzer

Proposed device for measuring distribution of masses and velocities of ions in plasma or ion beam of general type denoted variously as mass, velocity, and energy analyzers. Yields indications of charge-to-mass ratios and velocities; from these quantities, one computes masses and energies if one also either measures charges of ions by other means or else makes realistic assumption that each ion carries small number (usually 1) of fundamental units of electric charge. In comparison with older devices of this type, device smaller, and operates faster, yielding simultaneous indications of both charge-to-mass ratios and velocities.

Chutjian, Ara↗

Celestial mechanics

Tracking data analyses of Mariners 6 and 7 for determining Earth Moon mass ratio and Mars mass

Anderson, J. D.↗

Compact X-ray binaries in hierarchical triples. II - Separation of the inner binary

This paper presents an analytic solution for the behavior of the inner binary separation with time for a coplanar hierarchical triple system in which both the inner and outer orbit are (initially) circular. This separation will be important if the inner binary is a mass transferring binary system, since in this case small changes in the inner binary separation are likely to result in significant changes in the mass-transfer rate and hence in the luminosity. The timing of the minima in the separation, when such luminosity bursts would occur, is shown to be strongly dependent on the inner binary mass ratio and might therefore serve as a diagnostic on the inner binary mass ratio in such systems. The advantages and drawbacks of the method are discussed.

Bailyn, Charles D.↗

Results of a parametric aeroelastic stability analysis of a generic X-wing aircraft

This paper discusses the trends in longitudinal dynamic aeroelastic stability of a generic x-wing aircraft model with design parameter variations. X-wing rotor blade sweep angle, ratio of blade mass to total vehicle mass, blade structural stiffness cross-coupling and vehicle center-of-gravity location were parameters considered. The typical instability encountered is body-freedom flutter involving a low frequency interaction of the first elastic mode and the aircraft short period mode. Parametric cases with the lowest static margin consistently demonstrated the highest flutter dynamic pressures. As mass ratio was increased, the flutter boundary decreased. The decrease was emphasized as center-of-gravity location was moved forward. As sweep angle varied, it was observed that the resulting increase in forward-swept blade bending amplitude relative to aft blade bending amplitude in the first elastic mode had a stabilizing effect on the flutter boundary. Finally, small amounts of stiffness cross-coupling in the aft blades increased flutter dynamic pressure.

Woods, Jessica A.↗

Results of a parametric aeroelastic stability analysis of a generic X-wing aircraft

This paper discusses the trend in longitudinal dynamic aeroelastic stability of a generic X-Wing aircraft model with design parameter variations. X-Wing rotor blade sweep angle, ratio of blade mass to total vehicle mass, blade structural stiffness cross-coupling and vehicle center-of-gravity location were parameters considered. The typical instability encountered is body-freedom flutter involving a low frequency interaction of the first elastic mode and the aircraft short period mode. Parametric cases with the lowest static margin consistently demonstrated the highest flutter dynamic pressures. As mass ratio was increased, the flutter boundary decreased. The decrease was emphasized as center-of-gravity location was moved forward. As sweep angle varied, it was observed that the resulting increase in forward-swept blade bending amplitude relative to aft blade bending amplitude in the first elastic mode had a stabilizing effect on the flutter boundary. Finally, small amounts of stiffness cross-coupling in the aft blades increased flutter dynamic pressure.

Woods, Jessica A.↗

Evaporation, ignition, and combustion of nondilute clusters of drops

A theory of evaporation, ignition, and burning of moderately dense spherical drop clusters has been developed. The theory takes into account burning of premixed air and fuel internal to the cluster at ignition and subsequent burning of fuel emitted from the cluster by a flame sheet surrounding it. The model considers interdrop interaction, momentum exchange between drops and gas, and turbulent exchange processes between the cluster and its surroundings. Calculations are performed for varying initial air-to-fuel-mass ratios, initial cluster radii, ambient gas temperatures and initial drop temperatures. Results are presented for ratios of fuel mass burned to fuel mass lost from the cluster between drop ignition and drop disappearance, fuel burned fractions at ignition and at the moment of drop disappearance, and jump conditions at ignition.

Bellan, J.↗

OGLE-2018-BLG-1185b: A Low-mass Microlensing Planet Orbiting a Low-mass Dwarf

We report an analysis of the planetary microlensing event OGLE-2018-BLG-1185, which was observed by a large number of ground-based telescopes and by the Spitzer Space Telescope. The ground-based light curve indicates a low planet–host star mass ratio ofq=(6.9±0.2)×10−5, which is near the peak of the wide-orbit exoplanet mass-ratio distribution. We estimate the host star and planet masses with a Bayesian analysis using the measured angular Einstein radius under the assumption that stars of all masses have an equal probability of hosting the planet. The flux variation observed by Spitzer is marginal, but still places a constraint on the microlens parallax. Imposing a conservative constraint that this flux variation should beΔfSpz<4 instrumental flux units yields a host mass of=-+MM0.37 host 0.210.35 and a planet mass of =-+ÅmM8.4p4.77.9. A Bayesian analysis including the full parallax constraint from Spitzer suggests smaller host star and planet masses of =-+MM0.091 host 0.0180.064 and =-+ÅmM2.1p0.41.5, respectively. Future high-resolution imaging observations with the Hubble Space Telescope or Extremely Large Telescope could distinguish between these two scenarios and help reveal the planetary system properties in more detail.

Gravitational microlensing↗

OGLE-2018-BLG-1700L: Microlensing Planet in Binary Stellar System

We report a planet in a binary that was discovered from the analysis of the microlensing event OGLE-2018-BLG-1700. We identify the triple nature of the lens from the fact that the anomaly pattern can be decomposed into two parts produced by two binary-lens events, in which one binary pair has a mass ratio of ∼0.01 between the lens components and the other pair has a mass ratio of ∼0.3. We find two sets of degenerate solutions, in which one solution has a projected separation between the primary and its stellar companion less than the angular Einstein radius θ(E) (close solution), while the other solution has a separation greater than θ(E) (wide solution). From the Bayesian analysis with the constraints of the event timescale and angular Einstein radius, we find that the planet has a mass of 4.4(sup +3.0, sub -2.0) M(J) and the stellar binary components have masses of 0.42 (sup +0.29, sub -0.19) M(ʘ) and 0.12 (sup +0.08, sub -0.05) M(ʘ) , respectively, and the distance to the lens is D(L) = 7.6 (sup +1.2, sub -0.9) kpc. The planet is a circumstellar planet according to the wide solution, while it is a circumbinary planet according to the close solution.

Cheongho Han↗