Challenges in developing materials for microreactors: A case-study of yttrium dihydride in extreme conditions
Not Available
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
Not Available
The project goal was to improve the quality of boron phosphide (BP) by optimizing its epitaxial growth on single crystal substrates and by producing bulk BP single crystals with low dislocation densities. BP is potentially a good semiconductor for high efficiency solid state neutron detectors by combining neutron capture and charge creation within the same volume. The project strategy was to use newly available single crystal substrates, silicon carbide and aluminum nitride, engineered to produce the best film properties. Substrate variables included the SiC polytype, crystallographic planes, misorientation of the substrate surface (tilt direction and magnitude) from the major crystallographic plane, and surface polarity (Si and C). The best films were (111)BP on silicon-face (0001) 4H-SiC misoriented 4° in the [1-100] direction, and BP on (100) and (111) 3C-SiC/Si; these substrates resulted in films that were free of in-plane twin defects, as determined by x-ray topography. The impact of the deposition temperature was also assessed: increasing the temperature from 1000 °C to 1200 °C produced films that were more ordered and more uniform, and the size of individual grains increased by more than a factor of twenty. The BP films were free of other compounds such as icosahedral boron phosphide (B 12 P 2 ) over the entire temperature range, as established by Raman spectroscopy. The roughness of the BP films was reduced by increasing the phosphine to diborane ratio from 50 to 200. Bulk crystals were grown by reacting boron dissolved in nickel with phosphorus vapor to precipitate BP. Crystals with dimensions up to 2 mm were produced.
The objective of the work performed under this CRADA is to assist Garmor to quantify technical and cost payoffs of achieving a very high through-plane electrical conductivity in a composite BPP for Proton Exchange Membrane Fuel Cells (PEMFCs).
Abstract not provided.
The HyS process, driven by solar power, has great potential to reach high-efficiency and low-cost hydrogen production without greenhouse gas emissions. The high-temperature section of the HyS cycle, which operates the catalytic decomposition of sulfuric acid into sulfur dioxide, oxygen, and water, is a fundamental part of the cycle affecting the overall plant efficiency and cost. Therefore, a high-performance catalyst (i.e., low cost, high catalytic activity, and low degradation catalyst) is of critical importance to achieve high efficiency and low hydrogen cost. Research and development has highlighted that a Pt-based monometallic catalyst had unacceptable catalytic activity and performance degradation for a high-efficiency and low-cost hydrogen production process. A high-efficiency solar receiver-reactor system, which incorporates the new catalyst, also needs to be developed to achieve the required plant efficiency and cost. Greenway Energy (GWE) and the University of South Carolina (USC), partnering with HydroGEN node laboratories Idaho National Laboratory (INL), Savannah River National Laboratory (SRNL), and National Renewable Energy Laboratory (NREL), propose the development of a new catalyst formulation, included in a novel solar receiver-reactor concept, to be tested experimentally in the last part of the project.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The goals of Office of Clean Coal are: (1) Improved energy security; (2) Reduced green house gas emissions; (3) High tech job creation; and (4) Reduced energy costs. The goals of the Hydrogen from Coal Program are: (1) Prove the feasibility of a 40% efficient, near zero emissions IGCC plant that uses membrane separation technology and other advanced technologies to reduce the cost of electricity by at least 35%; and (2) Develop H{sub 2} production and processing technologies that will contribute {approx}3% in improved efficiency and 12% reduction in cost of electricity.
A brief historical review of the evolution in structural materials options for fusion energy systems is presented, along with the author s perspective on emerging trends in advanced manufacturing techniques and new high-performance materials.
Explore the source record for details and available documents.
Abstract not provided.
Abstract not provided.
Abstract not provided.
Abstract not provided.
Abstract not provided.