SEARCH · Search NASA

Results for “Microstructural Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

DOE OSTI2026

Spatial and temporal characterization of municipal solid waste based on resource recovery pathways

This study presents a two-year, quarterly assessment of MSW across four source sectors (residential, schools, restaurants, and grocery stores) from sixteen sites across five U.S. states. MSW was manually sorted into 27 categories and aggregated into pathway fractions: high-moisture (HM) organics, low-moisture (LM) organics, recyclable (RC) materials, and residuals for disposal. Organics represented 89 % of the MSW stream. The largest fraction was HM organics consisting of food waste (31 %) and yard waste (3 %), with large coefficient of variations (CV), 79 and 278 %, respectively, reflecting high seasonal and site variability that varied significantly (p < 0.01) across sampling periods. The HM fraction showed properties favorable for anaerobic digestion, with moisture content ranging from 56 to 95 % and volatile solids ranges of 86-95 %. In contrast, the LM and RC fractions remained more stable (plastics CV = 41 %; paper CV = 53 %) with heating values up to 26.9 MJ/kg across sources, reflecting suitability for gasification. Microstructural analysis revealed less porosity in residential waste sampled at the landfill, which can influence preprocessing efficiency and microbial accessibility. Pathway informed allocations showed that 35 % of MSW is suitable for anaerobic digestion, 36 % for gasification, and 18 % for recycling, leaving 11 % requiring landfill disposal. These results provide quantitative evidence to determine feedstock allocation, waste-to-energy system design, and the development of data-driven sustainability and resource recovery strategies within a circular bioeconomy.

09 BIOMASS FUELS↗

DOE OSTI2025

Creep Deformation and Damage Mechanisms in an Advanced High-Temperature Additively Manufactured Nickel-Base Superalloy

Abstract This research investigates the processing–structure–properties–performance relationship in a novel nickel-base superalloy, ABD ® -900AM, designed for extreme environments. Specifically tailored for additive manufacturing (AM), ABD ® -900AM maintains mechanical integrity at high temperatures and is comparable to other nickel-based superalloys with a 30–40% gamma-prime volume fraction. A comprehensive study was conducted using laser-beam powder bed fusion and electron-beam powder bed fusion methods. Factors such as heat treatment, porosity, build orientation, and hot isostatic pressing were evaluated to understand their effects on microstructure and mechanical performance. Microstructural characterization revealed significant differences in grain size and orientation across build processes and heat treatments. High-temperature mechanical testing indicated that grain size, heat treatment, and orientation significantly influence creep behavior. A super-solvus heat treatment led to recrystallization and grain growth, significantly improving creep properties compared to a near-solvus heat treatment. Various creep mechanisms were identified across different conditions, and creep rupture models were developed for each build process. Post-test microstructural analysis showed grain boundary damage, with differences in creep cavitation morphology under varying stress conditions. It was shown that MC carbides grow at the expense of gamma-prime near grain boundaries, leading to precipitate-free zones in specimens tested at higher temperatures. This study fills a significant gap in fundamental research by offering a deeper insight into the high-temperature mechanical behavior of additively manufactured nickel-base superalloys. It also explores critical research questions regarding the role of carbides and the significance of heat treatment. The insights gained enhance confidence in the industry adoption of ABD ® -900AM and similar alloys for high-temperature applications, bridging the knowledge gap and supporting the development of reliable AM processes for extreme environments.

Bridges, Alex (ORCID:000000030338759X)↗

DOE OSTI2026

Tensile creep properties of NbTaTi and NbTaTiV refractory complex concentrated alloys

Refractory complex concentrated alloys (RCCAs) have emerged as promising candidates for high-temperature structural applications due to their high melting points and potential for exceptional strength, whereas their creep properties remain relatively underexplored. Here, we investigate the tensile creep behavior of NbTaTi and NbTaTiV in high vacuum to elucidate the influence of alloying on creep mechanisms. NbTaTiV exhibits higher creep resistance than NbTaTi, which is attributed to V-induced edge-dislocation-glide-controlled deformation. Microstructural analysis reveals the formation of Ti- and interstitial impurity-rich secondary phases during creep, which enhances the creep resistance without significant embrittlement. Stress exponents (∼3) and activation energies (∼those for vacancy diffusion) align with thermally activated dislocation glide-controlled creep. Despite NbTaTiV surpassing Ni-based superalloys in yield strength at elevated temperatures, its single-phase BCC structure limits creep resistance under engineering-relevant conditions, highlighting the necessity of deliberate secondary phase design to achieve competitive high-temperature performance.

Complex concentrated alloys↗

DOE OSTI2026

Establishing an acoustic-property relationship in laser powder bed fusion with machine learning

Quality control of Laser Powder Bed Fusion (PBF-LB) additively manufactured parts is an important hurdle inhibiting the technology’s use structural applications. Acoustic monitoring of the laser powder bed fusion process can detect defects in-situ that are known to degrade mechanical properties. However, processing-structure-property (PSP) relationships are required to extrapolate from detected defects to part performance. Here, this study explores how acoustics may be a suitable signature linking processing conditions to properties, thus effectively substituting for structure in the PSP relationship. Establishing such a relationship would enable a part’s mechanical performance to be directly predicted from its acoustic signature, reducing the need for destructive testing or microstructural analysis to ensure a part will meet performance requirements. One hundred CoCrFeMnNi high entropy alloy tensile bars were printed across 13 process conditions in a series of 6 prints. The acoustic signatures of these tensile bars were used to train machine learning models to predict each part’s mechanical properties. By using both process information and acoustic information to predict mechanical properties, yield strength was predicted 18% more accurately and ductility to failure was predicted 10% more accurately than is achieved when using duplicate parts to predict part performance. Finally, individual acoustic frequencies were investigated to determine why acoustic signatures improve mechanical property predictions and the potential physical origins of these signatures. This work demonstrates how blending acoustics, process information, and machine learning can provide in-situ diagnostics of mechanical properties and improve the reliability of the PBF-LB process.

Acoustic emission↗

DOE OSTI2025

Silver diamine fluoride differentially affects dentin and hypomineralized enamel permeabilities

OBJECTIVES: To investigate the physicochemical effect of silver diamine fluoride (SDF) by correlating permeability with mineral density and elemental composition of hypomineralized enamel and carious dentin. METHODS: Enamel and dentin from human carious primary teeth with and without SDF treatment in-vivo, and hypomineralized enamel from permanent molars with and without SDF treatment in-vitro were scanned using micro X-ray computed tomography. Spatial maps of biometals (calcium, zinc), phosphorus, and silver were generated using X-ray fluorescence microprobe. Permeabilities were computed using Porous Microstructure Analysis software. RESULTS: The intrinsic permeability of SDF-treated carious dentin was 14.3 % lower than untreated sound dentin (6.39e-15 ± 3.01e-15 m² vs 7.46e-15 ± 1.82e-15 m²; P < 0.0001), while untreated carious dentin was 98.4 % higher (1.48e-14 ± 7.11e-15 m²; P < 0.0001). SDF-treated and untreated transparent dentin showed similar reduced permeabilities (75.6 % and 78.4 % lower than untreated sound dentin, respectively; P = 0.93). Severely hypomineralized enamel showed permeability reaching 108.1 % of adjacent sound dentin (5.71e-15 ± 2.04e-15 m² vs 5.28e-15 ± 1.30e-15 m²; P = 0.1409) and was significantly higher than mildly hypomineralized enamel (1.39e-15 ± 1.04e-15 m²; P < 0.0001). SDF treatment did not significantly impact the permeability of severely hypomineralized enamel (12.4 % reduction; P = 0.07). Principal component regression identified Zn level as a significant effector of tissue permeabilities in carious primary teeth (P < 0.0001). SIGNIFICANCE: This study introduces a computational method to measure dental tissue permeability, and demonstrates that SDF significantly reduces permeability in carious dentin but not intact hypomineralized enamel. The study reveals biometal Zn localization can alter dentin and enamel permeabilities, providing new insights into pathobiological mechanisms underlying caries and hypomineralization.

Chou, Conrad↗

DOE OSTI2025

High-temperature stability and thermal expansion behavior of equi-atomic refractory multi-principal element alloys based on MoNbTi system for Gen IV reactor applications

The present study investigates the thermal stability and thermal expansion behavior of seven equi-atomic refractory multi-principal element alloys (MPEAs) based on the MoNbTi ternary system composed of low neutron absorption cross section elements. Through an integrated approach utilizing in-situ high-temperature X-ray diffraction (HT-XRD) in conjunction with differential scanning calorimetry (DSC), dilatometry and ageing heat treatment, the thermal stability of the MPEAs was comprehensively analyzed. In-situ HT-XRD experiment confirmed the stability of the room temperature phases up to 1000 °C with no peaks observed corresponding to additional phases in the HT-XRD patterns at 500, 800 and 1100 °C. DSC thermograms showed the absence of peaks up to 1000 °C, while peaks and valleys corresponding to exothermic and endothermic events were observed above 1000 °C. Coefficient of thermal expansion (CTE) derived from second order polynomial fitting of linear thermal expansion data from the dilatometry experiment showed linear increment up to 1000 °C for all the alloys except those containing Zr. The Cr containing alloys exhibited notably higher CTE values, particularly the Al containing alloy exhibited the highest value. Ageing heat treatment at 800 and 1000 °C for 96 h and subsequent microstructural analysis revealed significant precipitation of secondary phases in MoNbTiZr, MoNbTiZrV and MoNbTiCrAl. In conclusion, a substantial increase in hardness was observed in MoNbTiZr and MoNbTiCrAl due to secondary phase precipitation, while the other alloys maintained hardness values comparable to their as-cast and homogenized states.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

A Novel Surface Restoration Method for Hydropower Steel Components: Plasma Gouging and Inconel Cold Spray Coating for Material Repair

A novel surface restoration approach combining plasma gouging with subsequent cold spray deposition is demonstrated in this study. Plasma gouging effectively removes the damaged steel surface, leaving grooves and forming a plasma gouging affected zone up to ~300?µm thick. Within this zone, a hardened martensitic layer with a peak hardness of ~370?HV—almost twice that of the base substrate (~200?HV)—is produced. Following plasma gouging, cold spray deposition is applied to rebuild the surface. Experimental results reveal that cold spray coatings deposited at low energy suffer from delamination, whereas high energy cold spray deposits yield a well-bonded coating. Microstructural analysis further shows that the martensitic layer formed by plasma gouging undergoes dynamic recrystallization during cold spray, reducing the hardness to 317?HV. These findings demonstrate the feasibility of this hybrid method for effective surface restoration of damaged steel components.

Wang, Tianhao↗

DOE OSTI2025

Optimizing processing conditions for additively reinforced thermoforming (ART) in convergent manufacturing

This study utilized additively reinforced thermoforming (ART) to enhance the thermomechanical properties of polyethylene terephthalate glycol (PETG) sheet. ART materials were produced by overprinting PETG/carbon fiber filament (PETG/CF) on neat PETG sheets at varying conditions. The mechanical properties of the PETG sheet, PETG/CF, and ART materials were assessed, showing that ART exhibited superior tensile strength and modulus of elasticity. The tensile strength and modulus in the x-direction for ART at 265°C were 57.32 ± 2.9 MPa and 3.41 ± 0.4 GPa, respectively, compared to 49.1 ± 0.5 MPa and 1.92 ± 0.09 GPa for neat PETG. Microstructural analysis revealed strong interfacial adhesion between layers, while thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and heat deflection temperature analysis provided insights into the ART material's thermoforming behavior, aiding design optimization for enhanced stiffness, reduced necking, and improved customization. In conclusion, this information can be used to design for the thermoforming operation.

Additive reinforcement↗

DOE OSTI2026

Temperature dependent interfacial microstructure in HIP-bonded Al6061/Zr joints

Pressing (HIP) at 450 °C and 560 °C under 103 MPa for 90 minutes to evaluate interfacial diffusion and microstructural evolution. Sound metallurgical bonding was achieved at both temperatures, with Zr serving as an effective diffusion barrier. Microstructural analysis revealed the the formation of a (Al,Si)3Zr intermetallic layer at the Al/Zr interface, whose thickness increased from ~100 nm at 450 °C to ~2100 nm at 560 °C, consistent with temperature-driven diffusion kinetics. The thin and continuous reaction layer observed at 450 °C indicates controlled interdiffusion and minimal reaction zone growth, favorable for maintaining interface stability and ductility. At 560 °C, enhanced atomic mobility led to pronounced intermetallic development, confirming diffusion-controlled growth behavior. These results provide valuable insights for optimizing Al/Zr interface design and diffusion barrier performance in advanced structural and energy systems.

Al/Zr interface↗

DOE OSTI2024

Integration of CeO 2 -Based Memristor with Vertically Aligned Nanocomposite Thin Film: Enabling Selective Conductive Filament Formation for High-Performance Electronic Synapses

The CeO 2 -based memristor has attracted significant attention due to its intrinsic resistive switching (RS) properties, large on/off ratio, and great plasticity, making it a promising candidate for artificial synapses. However, significant challenges such as high power consumption and poor device reliability hinder its broad application in neuromorphic microchips. To tackle these issues, in this work, we design a novel bilayer (BL) memristor by integrating a CeO 2 -based memristor with a Co-CeO 2 vertically aligned nanocomposite (VAN) layer and compare it with the single layer (SL) memristor. Preliminary electrical testing reveals that the BL memristor offers a reduced set/reset voltage (~67% lower), a higher on/off ratio (~5 × 10 2 ), enhanced device reliability, and improved device-to-device variation compared to the SL memristor. Insight from COMSOL simulation, coupled with microstructural analysis, provides a comprehensive elucidation on how the VAN layer facilitates the selective conductive filament (CF) formation. Subsequently, the plasticity of the BL memristor is evaluated through long-term potentiation/depression (LTP/LTD), paired-pulse facilitation (PPF), and spike-time-dependent plasticity (STDP). The spiking neural network (SNN) built upon the BL memristor achieves remarkable accuracy (~94%) after only 12 iterations, underscoring its potential for high-performance neural networks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Dynamics of Radiation Damage Buildup in Ultrathin Hexagonal Boron Nitride Films under Ion Bombardment

Two-dimensional hexagonal boron nitride (hBN) is attractive for several emerging applications. Ion bombardment can be used to modify the hBN properties. However, the understanding of radiation damage buildup in hBN remains limited. Here, we investigate the effects of the dose rate and ion mass on radiation damage buildup by studying 40 nm-thick hBN films bombarded at room temperature with 500 keV 4 He, 15 N, 40 Ar, and 129 Xe ions and comparing with results for ion bombardment of polycrystalline hBN ceramics. Raman spectroscopy is used to quantify damage buildup, and transmission electron microscopy is used for microstructural analysis. Experiments are complemented by molecular dynamics simulations of the formation and evolution of point defects. Lighter ions are found to be more efficient at disordering hBN than heavier ions. This observation points to a critical role of intracascade defect processes. In contrast, a negligible dose rate effect observed suggests limited intercascade defect dynamic annealing processes for these irradiation conditions. These findings provide a fundamental basis for hBN defect engineering.

2D materials↗

DOE OSTI2025

Eocene-Oligocene Metamorphism, Fluid Flow and Deformation in the Ruby Mountains-East Humboldt Range Metamorphic Core Complex

Metamorphic core complexes are ubiquitous in collapsed orogens globally and play a primary role in crustal exhumation. Here, we investigate the metamorphic history of the Ruby Mountains-East Humboldt Range metamorphic core complex, Nevada, using petrochronology to understand how magmatism, metamorphism and deformation interact to modulate crustal rheology, and the timing of exhumation within the Sevier orogenic belt. Field study, microstructural analysis, thermobarometry and laser ablation split-stream monazite, titanite and allanite petrochronology of the mylonitic footwall were integrated to elucidate the pressure-temperature-time (P-T-t) evolution. Major-, trace-element and quartz-in-garnet thermobarometry show peak metamorphism occurred at 5.5–6 kbar and 600–650°C across the study area. Monazite and titanite U-(Th)-Pb petrochronology constrain this episode of metamorphism to 88–81 Ma with the structurally deepest samples yielding dates down to ca. 71 Ma. The preservation of peak metamorphic mineral assemblages indicates these rocks remained at near-peak temperature conditions into the Cenozoic. Cenozoic metamorphism occurred during a punctuated episode contemporaneous with the Great Basin ignimbrite flare up. All samples show a distinct 39–37 Ma population of monazite, titanite and allanite dates that correlate with the emplacement of quartz diorite and gabbro intrusions throughout the footwall. Accessory phases contain zoning textures in backscattered electron images that are consistent with fluid-mediated dissolution-reprecipitation reactions. The U-(Th)-Pb analyses from these zones yield 39–27 Ma dates interpreted as the timing of fluid flow. The results of this study elucidate the integrated importance of magmatism, melting and fluid flow in driving the coupled evolution of Late Cretaceous metamorphism within the Sevier hinterland and the subsequent Cenozoic metamorphic core complex development that exhumed the middle crust.

58 GEOSCIENCES↗

DOE OSTI2025

Rheology improvement for silicon nitride and resin slurries for vat photopolymerization printing and sintering

This work presents the formulation, rheological characterization, and sintering of silicon nitride (Si₃N₄) slurries for vat photopolymerization (VPP) using digital light processing (DLP). Bimodal Si₃N₄ powder was dispersed into commercial photopolymer resin using two different dispersants with opposing effects on surface charge, resulting in varied slurry stability and flow behavior. Slurries were engineered to exhibit shear-thinning behavior suitable for VPP, and their flow properties were quantified using a power-law fluid model. The formulations achieved cure depths of approximately 40 µm and enabled printing of green bodies. Post-processing included thermal debinding and liquid-phase sintering, yielding primarily β-Si₃N₄ with a minor Y-Si-Al-O-N glass phase. The sintered parts reached ~85% of theoretical density and demonstrated a flexural strength of ~330 MPa. Microstructural analysis revealed closed porosity along with some defects related to powder agglomeration and interlayer adhesion. These findings provide insights into slurry formulation strategies for additive manufacturing of high-performance non-oxide ceramics.

Aerospace engineering↗

DOE OSTI2025

Cr-Be Pushered Single Shell (PSS) Capsule Development

Pushered single shell (PSS) has emerged as an alternative platform of implosion to ease the stability issue at the ablation front. The design consists of a thin inner Be layer, a 50% Cr:Be plateau region, an S-curve gradient, a low Cr (1.5%) tamper layer, and followed by a pure Be outer layer. General Atomics has developed a way to fabricate the higher-Z Cr to lower-Z Be gradients on glow discharge polymer mandrels with a designed S-shape profile for optimal implosion stability using magnetron sputtering. Microstructure analysis of the gradient coating indicated that at lower Cr concentration a short order or amorphous structure was formed. Here, these fabricated PSS capsules were subsequently built into capsule fill tube assemblies, verified to be leak tight at both ambient and cryogenic conditions, and delivered to Lawrence Livermore National Laboratory for the shots. The capsule thermal stability was demonstrated by invariable Cr profiles before and after pyrolysis. However, cracking at inner Cr layers was observed, which has been attributed to thermal stress.

Capsule↗

DOE OSTI2025

Compatibility of molten plutonium with wrought and additively manufactured metal crucibles

Understanding plutonium’s interaction with metals is crucial for optimizing pyrochemical operations, nuclear fuel containment, and various actinide processing techniques. Traditionally, tantalum crucibles are employed for plutonium processing due to their high durability, excellent temperature stability, and low solubility in plutonium. However, tantalum faces challenges such as plutonium wetting and diffusion, making surface coatings particularly important for crucibles in pyrochemical applications to enhance corrosion resistance against plutonium. Tantalum is also expensive and difficult to machine, prompting the need for advanced manufacturing techniques to address these challenges. Here, in this work, we investigate the interaction of Pu with tantalum and titanium crucibles fabricated using both traditional machining methods and laser powder bed fusion (LPBF) additive manufacturing (AM). LPBF-AM is an advanced technique that allows for the creation of complex geometries from traditionally difficult-to-machine metals by using a high-powered laser to build parts. Previous studies of conventional manufactured tantalum have utilized oxidation and carburization of the surface to mitigate plutonium wetting; however, no studies of surface modified LPBF-AM material have been undertaken. These studies are crucial, given the typical differences in the grain structure between conventional and LPBF-AM materials. All crucibles underwent differential scanning calorimetry to confirm the melting of plutonium. Subsequently, the crucibles were sectioned and mounted in epoxy for microstructural analysis using optical microscopy and scanning electron microscopy. This investigation, comparing the performance of wrought vs AM metal crucibles, provides a basis for future tooling applications in actinide processing techniques and can address the challenges associated with traditional machining, particularly in pyrochemical applications.

Actinides↗

DOE OSTI2024

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗

DOE OSTI2024

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗