Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mode Commander”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

SRMS Assisted Docking and Undocking for the Orbiter Repair Maneuver

As part of the Orbiter Repair Maneuver (ORM) planned for Return to Flight (RTF) operations, the Shuttle Remote Manipulator System (SRMS) must undock the Orbiter, maneuver it through a complex trajectory at extremely low rates, present it to an EVA crewman at the end of the Space Station Remote Manipulator System to perform the Thermal Protection System (TPS) repair, and then retrace back through the trajectory to dock the Orbiter with the Orbiter Docking System (ODS). The initial and final segments of this operation involve the interaction between the SRMS, ISS, Orbiter and ODS. Previously, a technique entitled "SRMS assisted docking" for installation of a payload to the ODS had been developed and was utilized for the Russian provided Docking Module on STS-74 during Shuttle-Mir missions and both the Node 1 and FGB elements on STS-88/Flight 2A. This procedure consisted of the SRMS grappling the respective payload, maneuvering it to a pre-install position inches above the ODS Androgynous Peripheral Attachment System (APAS) ring, commanding the SRMS into Test mode (which allows brakes-off motion of the joints), and then down-firing Primary Reaction Control System (PRCS) jets in order to effect a capture of the APAS latches. Once a successful capture had been achieved, then the AP AS was operated through its nominal retraction sequence to complete the mating sequence. While this technique can once again be used for the tail end docking portion of the ORM, the initial undocking of the orbiter and ISS vehicles with the assistance of the SRMS has yet to be attempted on orbit. The objective here is to determine the most efficient means to separate or extract the vehicles. Two techniques were analyzed in support of RTF: (1) the 'nominal' demating from the mated interface, and (2) the SRMS performing the operation (either in an active or passive fashion). In the first operation, the demating process would replicate standard undocking operations, with the exception that the SRMS is allowed to arrest the resulting motion. The second operation would be to extend the APAS ring to a ready to dock position, open the capture latches, and then detach the vehicles using the SRMS either actively or passively. In the active case, the APAS ring is extended and latched, and the SRMS is commanded to pull the two interfaces apart (assuming that the effective pull force of the SRMS can overcome the spec values of the combined latch resistance). In the passive case, the SRMS brakes are engaged and the AP AS mechanism is commanded to retract, pulling the two interfaces apart. Since the emphasis of both STS-74 and STS-88 had solely been on the installation operation, as opposed to the separation operation, two new models required development and incorporation within simulation tools designed to analyze those scenarios. These enhancements included: (1) a detailed demating dynamics model to characterize the pusher spring characteristics during undocking, and (2) contact and mechanical system modeling of the back side of the latches to represent unlatching dynamics. This paper first provides an overview of the Monte-Carlo screening analysis for the installation (both nominal and contingency), including the variation of separation distance, misalignment conditions, SRMS joint/brake parameter characteristics, and PRCS jet combinations and corresponding thrust durations. The resulting 'optimum' solution is presented based on trade studies between predicted capture success and integrated system loads. This paper then discusses the upgrades to the APAS math model associated with the new SRMS assisted undocking technique and reviews simulation results for various options investigated for either the active and passive separation of the ISS from the Orbiter.

Space Station Remote Manipulator System↗
NASA NTRS2011

Space Environments Testbed

The Space Environments Testbed (SET) is a flight controller data system for the Common Carrier Assembly. The SET-1 flight software provides the command, telemetry, and experiment control to ground operators for the SET-1 mission. Modes of operation (see dia gram) include: a) Boot Mode that is initiated at application of power to the processor card, and runs memory diagnostics. It may be entered via ground command or autonomously based upon fault detection. b) Maintenance Mode that allows for limited carrier health monitoring, including power telemetry monitoring on a non-interference basis. c) Safe Mode is a predefined, minimum power safehold configuration with power to experiments removed and carrier functionality minimized. It is used to troubleshoot problems that occur during flight. d) Operations Mode is used for normal experiment carrier operations. It may be entered only via ground command from Safe Mode.

Leucht, David K.↗
NASA NTRS1981

Toggled signal for prevention of control errors

Redundant command lines use two different "true" signals to avoid common failure modes. When function is required to operate, computer generates command and transmits it to demultiplexer, where it is split along two paths, producing outputs from separate electronic cards. Outputs combine to drive AND gate high and begin function.

Wyllie, C. E.↗
NASA NTRS1978

MBASIC batch processor architectural overview

The MBASIC (TM) batch processor, a language translator designed to operate in the MBASIC (TM) environment is described. Features include: (1) a CONVERT TO BATCH command, usable from the ready mode; and (2) translation of the users program in stages through several levels of intermediate language and optimization. The processor is to be designed and implemented in both machine-independent and machine-dependent sections. The architecture is planned so that optimization processes are transparent to the rest of the system and need not be included in the first design implementation cycle.

Reynolds, S. M.↗
NASA NTRS1980

Eight microprocessor-based instrument data systems in the Galileo Orbiter spacecraft

Instrument data systems consist of a microprocessor, 3K bytes of Read Only Memory and 3K bytes of Random Access Memory. It interfaces with the spacecraft data bus through an isolated user interface with a direct memory access bus adaptor, and/or parallel data from instrument devices such as registers, buffers, analog to digital converters, multiplexers, and solid state sensors. These data systems support the spacecraft hardware and software communication protocol, decode and process instrument commands, generate continuous instrument operating modes, control the instrument mechanisms, acquire, process, format, and output instrument science data.

Barry, R. C.↗
NASA NTRS1980

Dual charge-coupled device /CCD/, astronomical spectrometer and direct imaging camera. II - Data handling and control systems

The data collection system for the MASCOT (MIT Astronomical Spectrometer/Camera for Optical Telescopes) is described. The system relies on an RCA 1802 microprocessor-based controller, which serves to collect and format data, to present data to a scan converter, and to operate a device communication bus. A NOVA minicomputer is used to record and recall frame images and to perform refined image processing. The RCA 1802 also provides instrument mode control for the MASCOT. Commands are issued using STOIC, a FORTH-like language. Sufficient flexibility has been provided so that a variety of CCDs can be accommodated.

Dewey, D.↗
NASA NTRS1981

LANDSAT-D flight segment operations manual, volume 2

Functions, performance capabilities, modes of operation, constraints, redundancy, commands, and telemetry are described for the thematic mapper; the global positioning system; the direct access S-band; the multispectral scanner; the payload correction; the thermal control subsystem; the solar array retention, deployment, and jettison assembly; and the boom antenna retention, deployment, and jettison assembly for LANDSAT 4.

Varhola, J.↗
NASA NTRS1972

Actuator participation in a bending mode identification system

A hydraulic actuator designed for a thrust vector control system used as a shaker for a vehicle to determine the bending mode frequencies is described. The actuator is used as the prime mover and the frequency sensor for the flexible vehicle in a test tower. Advantages in using the actuator piston position with respect to a commanded position to obtain the bending mode frequencies are shown.

Thompson, Z.↗
NASA NTRS1988

High level intelligent control of telerobotics systems

A high level robot command language is proposed for the autonomous mode of an advanced telerobotics system and a predictive display mechanism for the teleoperational model. It is believed that any such system will involve some mixture of these two modes, since, although artificial intelligence can facilitate significant autonomy, a system that can resort to teleoperation will always have the advantage. The high level command language will allow humans to give the robot instructions in a very natural manner. The robot will then analyze these instructions to infer meaning so that is can translate the task into lower level executable primitives. If, however, the robot is unable to perform the task autonomously, it will switch to the teleoperational mode. The time delay between control movement and actual robot movement has always been a problem in teleoperations. The remote operator may not actually see (via a monitor) the results of high actions for several seconds. A computer generated predictive display system is proposed whereby the operator can see a real-time model of the robot's environment and the delayed video picture on the monitor at the same time.

Mckee, James↗
NASA NTRS2010

Lunar Reconnaissance Orbiter (LRO) Sun Safe Mode

The Lunar Reconnaissance Orbiter (LRO), a spacecraft designed and built at the National Aeronautics and Space Administration s (NASA) Goddard Space Flight Center (GSFC) in Greenbelt, MD, was launched on June 18, 2009 from Cape Canaveral. It is currently in orbit about the Moon taking detailed science measurements and providing a highly accurate mapping of the suface in preparation for the future return of astronauts to a permanent moon base. Onboard the spacecraft is a complex set of algorithms designed by the attitude control engineers at GSFC to control the pointig for all operational events, including anomalies that require the spacecraft to be put into a well known attitude configuration for a sufficiently long duration to allow for the investigation and correction of the anomaly. GSFC level requirements state that each spacecraft s control system design must include a configuration for this pointing and lso be able to maintain a thermally safe and power positive attitude. This stable control algorithm for anomalous events is commonly referred to as the safe mode and consists of control logic thatwill put the spacecraft in this safe configuration defined by the spacecraft s hardware, power and environment capabilities and limitations. The LRO Sun Safe mode consists of a coarse sun-pointing set of algorithms that puts the spacecraft into this thermally safe and power positive attitude and can be achieved wihin a required amount of time from any initial attitude, provided that the system momentum is within the momentum capability of the reaction wheels. On LRO the Sun Safe mode makes use of coarse sun sensors (CSS), an inertial reference unit (IRU) and reaction wheels (RW) to slew the spacecraft to a solar inertial pointing. The CSS and reaction wheels have some level of redundancy because of their numbers. However, the IRU is a single-point-failure piece of hardware. Without the rate information provided by the IRU, the Sun Safe control algorithms could not maintain the required pointing, so a sub-mode of the Sun Safe mode that does not use the IRU was designed. This submode, referred to as the Sun Safe Gyroless control mode, consists of an algorithm that estimates rate information from the CSS and the RW measurements. RW momentum information is used to estimate the body rate parallel to the target sunline, which CSS alone would not be able to observe. Sun Safe can be autonomously, or via ground command, entered from any other control mode and in the event the IRU is not providing rate information, the control mode is switched to the gyroless submode. This paper looks at the design of the Sun Safe modes and discusses the constraints placed on the algorithm and how the mode wored around these constraints. Items of particular interest include CSS placement on the Solar Array (SA) and its implications to design, estimation of body rate information for the Sun Safe Gyroless control mode, and the effect of solar eclipse on each of the Sun Safe modes. Placing CSS on the SA was necessary for the means to put the Sun along the targeted sun-line, nominally normal to the SA panels, for all operational considerations. This had design implications for determining a sun vector during normal SA operations, if one or both gimbals become inoperable and when the SA is in a stowed configuration. The ability of body rate estimation in Sun Safe Gyroless not only uses CSS sun vector data but requires RW momentum measuremens to estimate rates parallel to the sun-line. LRO encounters solar eclipses of some length for most of its orbits about the Moon. With the lack of CSS measurement data a design was implemented in both Sun Safe and Sun Safe Gyroless, they differ because of having or not having IRU measurement data, to carry the spacecraft through these eclipse periods. This paper also includes some discussion of sun avoidance and how it affected design decisions during nominal and eclipse perids for each of the Sun Safe modes.

Garrick, Joseph↗
NASA NTRS1975

The 4D area navigation system description and flight test results

A 4D area navigation system was designed to guide aircraft along a prespecified flight path (reference path) such that the aircraft would arrive at the approach gate at a time specified by the ATC controller. Key components to achieve this requirement were: (1) stored reference trajectories; (2) a continuously recomputed capture trajectory to a selected waypoint on the reference trajectory so as to achieve the desired time of arrival; (3) electronic situation displays; and (4) a control system to follow the overall trajectory in space and time. The system was implemented in a digital integrated avionics system (STOLAND) installed on a CV-340 airplane. Although the 4D system was designed primarily for automatic operation, it was flight tested in a flight director mode (the pilot follows the flight director commands), because the CV-340 autopilot servos were not tied to the avionics system. The flight test showed that, even in the flight director mode, the pilot did achieve the objectives of path tracking and time of arrival control with only moderate workload. The system also permitted controlled delay of the time of arrival by path stretching, which takes advantage of the continuously changing capture trajectory to predict the time of arrival. Simulations in the automatic and manual modes were used to complement the flight data.

Lee, H. Q.↗
NASA NTRS1991

Dynamic attitude command and control of the TOPEX/Poseidon spacecraft

The dynamic control laws utilized by the TOPEX/Poseidon (T/P) spacecraft attitude determination and control subsystem to command and maneuver the satellite during normal mission mode (NMM) laws are described. Results show that the vehicle is able to respond to the dynamic attitude commands while at the same time providing ample disturbance rejection capability.

Zimbelman, D. F.↗
NASA NTRS1987

Effects of joint rate and displacement constraints on stability regions

A block diagram showing plant dynamics in normal mode coordinates, a linear feedback controller with command limits, and actuator dynamics with rate and displacement limits is given. The objective is to examine the effects of joint rate and displacement saturation limits on the stability regions. An unstable short period dynamic model is transformed into normal mode coordinates and is augmented with actuator dynamics. A linear feedback controller is used to provide closed-loop stability. The stability with constrained actuator rate limits under varying bandwidth, displacement and command limits is examined.

Shrivastava, P. C.↗
NASA NTRS2005

Control method for video guidance sensor system

A method is provided for controlling operations in a video guidance sensor system wherein images of laser output signals transmitted by the system and returned from a target are captured and processed by the system to produce data used in tracking of the target. Six modes of operation are provided as follows: (i) a reset mode; (ii) a diagnostic mode; (iii) a standby mode; (iv) an acquisition mode; (v) a tracking mode; and (vi) a spot mode wherein captured images of returned laser signals are processed to produce data for all spots found in the image. The method provides for automatic transition to the standby mode from the reset mode after integrity checks are performed and from the diagnostic mode to the reset mode after diagnostic operations are carried out. Further, acceptance of reset and diagnostic commands is permitted only when the system is in the standby mode. The method also provides for automatic transition from the acquisition mode to the tracking mode when an acceptable target is found.

Howard, Richard T.↗
NASA NTRS1981

Application of the concept of dynamic trim control and nonlinear system inverses to automatic control of a vertical attitude takeoff and landing aircraft

A full envelope automatic flight control system based on nonlinear inverse systems concepts has been applied to a vertical attitude takeoff and landing (VATOL) fighter aircraft. A new method for using an airborne digital aircraft model to perform the inversion of a nonlinear aircraft model is presented together with the results of a simulation study of the nonlinear inverse system concept for the vertical-attitude hover mode. The system response to maneuver commands in the vertical attitude was found to be excellent; and recovery from large initial offsets and large disturbances was found to be very satisfactory.

Smith, G. A.↗
NASA NTRS1986

Multivariable control of a forward swept wing aircraft

The impact of independent canard and flaperon control of the longitudinal axis of a generic forward swept wing aircraft is examined. The Linear Quadratic Gaussian (LQG)/Loop Transfer Recovery (LTR) method is used to design three compensators: two single-input-single-output (SISO) systems, one with angle of attack as output and canard as control, the other with pitch attitude as output and canard as control, and a two-input-two-output system with both canard and flaperon controlling both the pitch attitude and angle of attack. The performances of the three systems are compared showing the addition of flaperon control allows the aircraft to perform in the precision control modes with very little loss of command following accuracy.

Quinn, W. W.↗
NASA NTRS1991

Linear quadratic servo control of a reusable rocket engine

A design method for a servo compensator is developed in the frequency domain using singular values. The method is applied to a reusable rocket engine. An intelligent control system for reusable rocket engines was proposed which includes a diagnostic system, a control system, and an intelligent coordinator which determines engine control strategies based on the identified failure modes. The method provides a means of generating various linear multivariable controllers capable of meeting performance and robustness specifications and accommodating failure modes identified by the diagnostic system. Command following with set point control is necessary for engine operation. A Kalman filter reconstructs the state while loop transfer recovery recovers the required degree of robustness while maintaining satisfactory rejection of sensor noise from the command error. The approach is applied to the design of a controller for a rocket engine satisfying performance constraints in the frequency domain. Simulation results demonstrate the performance of the linear design on a nonlinear engine model over all power levels during mainstage operation.

Musgrave, Jeffrey L.↗
NASA NTRS1994

Advanced Teleoperator Control System

Proposed teleoperator control system incorporates several advanced features to improve coordination between remote robotic manipulator (slave arm) and human operator at control manipulator (master arm). Provides superior performance in terms of error profiles and task-completion time in presence of human control errors varying over wide range and maintains stability under large signal-propagation delays. System highly robust in presence of nonlinearities and incorrect human commands in both position and rate modes of control.

Lee, Sukhan↗