Search NASA⌕ Search

SEARCH · Search NASA

Results for “NACA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

NACA Conference on Aircraft Loads, Structures, and Flutter

This document contains reproductions of technical papers on some of the most recent research results on aircraft loads, flutter, and structures from the NACA laboratories. These papers were presented by members of the staff of the NACA laboratories at the Conference held at the Langley Aeronautical Laboratory March 5, 6, and 7, 1957. The primary purpose of this Conference was to convey to contractors of the military services and others concerned with the design of aircraft these recent research results and to provide those attending an opportunity to discuss the results. The papers in this document are in the same form in which they were presented at the Conference in order to facilitate their prompt distribution. The original presentation and this record are considered as complementary to, rather than as substitutes for, the Committee?s more complete and formal reports. Accordingly, if information from this document is utilized it is requested that this document not be listed as a reference. Individual reports dealing with most of the information presented at the Conference will subsequently be published by NACA and will therefore be suitable as reference material.

Source record↗
NASA NTRS1953

Impingement of Water Droplets on NACA 65A004 Airfoil and Effect of Change in Airfoil Thickness from 12 to 4 Percent at 4 deg Angle of Attack

The trajectories of droplets in the air flowing past an NACA 65A004 a irfoil at an angle of attack of 4 deg were determined. The amount of water in droplet form impinging on the airfoil, the area of droplet impingement, and the rate of droplet impingement per unit area on the airfoil surface were calculated from the trajectories and presented to cover a large range of flight and atmospheric conditions. The effect of a change in airfoil thickness from 12 to 4 percent at 4 deg angle of attack is presented by comparing the impingement calculations for the NACA 65A004 airfoil with those for the NACA 65(sub 1)-208 and 65(sub 1)-212 airfoils. The rearward limit of impingement on the upper surface decreases as the airfoil thickness decreases. The rearward limit of impingement on the lower surface increases with a decrease in airfoil t hickness. The total water intercepted decreases as the airfoil thickness is decreased.

Brun, Rinaldo J.↗
NASA NTRS1981

Selected bibliography of NACA-NASA aircraft icing publications

A summary of NACA-NASA icing research from 1940 to 1962 is presented. It includes: the main results of the NACA icing program from 1940 to 1950; a selected bibliography of 132 NACA-NASA aircraft icing publications; a technical summary of each document cited in the selected bibliography; and a microfiche copy of each document cited in the selected bibliography.

John J Reinmann↗
NASA NTRS1987

Wind tunnel evaluation of a truncated NACA 64-621 airfoil for wind turbine applications

An experimental program to measure the aerodynamic performance of a NACA 64-621 airfoil with a truncated trailing edge for wind turbine applications has been conducted in the Ohio State University Aeronautical and Astronautical Research Laboratory 6 in. by 21 in. pressurized wind tunnel. The blunted or trailing edge truncated (TET) airfoil has an advantage over similar trailing edge airfoils because it is able to streamline a larger spar structure, while also providing aerodynamic properties that are quite good. Surface pressures were measured and integrated to determine the lift, pressure drag, and moment coefficients over angles of attack ranging from -14 to +90 deg at Mach 0.2 and Reynolds numbers of 1,000,000 and 600,000. Results are compared to the NACA 0025, 0030, and 0035 thick airfoils with sharp trailing edges. Comparison shows that the 30 percent thick NACA 64-621-TET airfoil has higher maximum lift, higher lift curve slope, lower drag at higher lift coefficients, and higher chordwise force coefficient than similar thick airfoils with sharp trailing edges.

Law, S. P.↗
NASA NTRS1922

The NACA Three Component Accelerometer

A new instrument known as the NACA three component accelerometer is described in this note. This instrument was designed by the technical staff of the NACA for recording accelerations along three mutually perpendicular axes, and is of the same type as the NACA single component accelerometer with the addition of two springs and a few minor improvements such as a pump for filling the dash-pots and a convenient method for aligning the springs. This note includes a few records as well as photographs of the instrument itself.

Reid, H J E↗
NASA NTRS1941

Hydrodynamic Tests of a 1/10-size Model of the Hull of the Latecoere 521 Flying Boat : NACA Model 83

A 1/10-size model of the hull of the French flying boat Latecoere 521 was tested in the NACA tank. This model is one of a series of models of the hulls of actual flying boats of both foreign and domestic type that are being tested in the NACA tank to provide information regarding the water characteristics of a variety of forms of hull and to illustrate the development of present-day types of flying boat. The lines and the offsets of the hull were obtained from the manufacturer through the Paris office of the NACA. The form of the stub-wing stabilizers was not furnished and, therefore, the model was tested without them. The model was tested free to trim at the design initial load (initial load coefficient of 0.428) and by the general method at load coefficients from 0.025 to 0.6. The spray characteristics of the model are good. The form of the bow would be particularly desirable for rough water use. The interference of the afterbody and the tail extension is excessive, causing very high resistance at high speeds. A violent vertical instability is present at trims of 4 degrees and 6 degrees with light loads and high speeds.

Olson, Roland E↗
NASA NTRS1953

A comparison of typical national gas turbine establishment and NACA axial-flow compressor blade sections in cascade at low speed

Comparative cascade tests of the NGTE (National Gas Turbine Establishment of Great Britain) 10C4/30C50 and NACA 65-(12)10 axial flow compressor blade sections were conducted in a 5-inch low-speed cascade tunnel at the Langley Laboratory at air-inlet angles of 30 degrees, 45 degrees, and 60 degrees and a solidity of 1.0 by using the porous-wall technique. These NACA data for the NGTE 10C4/30C50 section were also compared with data from NGTE design charts for the same section. British and NACA incompressible cascade force-analysis equations are included.

CASCADES, EXPERIMENT↗
NASA NTRS1939

Tests of NACA 0009, 0012, and 0018 Airfoils in the Full-Scale Tunnel

An investigation was conducted in the NACA full-scale wind tunnel to determine the aerodynamic characteristics of the NACA 0009, 0012, and 0018 airfoils, with the ultimate purpose of providing data to be used as a basis for comparison with other wind-tunnel data, mainly in the study of scale and turbulence effects. Three symmetrical 6 by 36-foot rectangular airfoils were used. The Reynolds number range for minimum drag was form 1,800,000 to 7,000,000 and for maximum lift, from 1,700,000 to 4,500,000. The effect of rounded tips was determined for each of the airfoils. Tests were also made of the NACA 0012 airfoil equipped with a 0.20c full-span split flap hinged at 0.80c. Tuft surveys were included to show the progressive breakdown of flow near maximum lift. Momentum surveys were made in conjunction with force measurements at zero lift as an aid in converting force-test data to section coefficients.

Goett, Harry J↗
NASA NTRS1941

Tests of the NACA 0025 and 0035 Airfoils in the Full-Scale Wind Tunnel

This report presents the results of an investigation conducted in the NACA full-scale wind tunnel to determine the aerodynamic characteristics of the 6 by 36-foot rectangular NACA 0025 and 0035 airfoils. The aerodynamic characteristics of the plain airfoils with rounded and square tips were determined by force tests through a complete angle-of-attack range, in addition, the profile drag was determined by the momentum method. The transition points on the airfoils were located by boundary-layer determinations with small total-head and static tubes. Each airfoil was also tested with a 0.20c full-span split flap. Tuft surveys were included to show the progressive breakdown of flow with increasing angles of attack. Previously published data from tests of the NACA 0009, 0012, and 0018 airfoils in the full-scale tunnel have been included in the summary curves.

Bullivant, W Kenneth↗
NASA NTRS1941

Pressure distribution over NACA 23012 airfoil with a slotted and a split flap

A pressure-distribution investigation has been conducted in the NACA 4 by 6-foot vertical wind tunnel to determine the air loads on an NACA 23012 airfoil in combination with a 25.66-percent-chord slotted flap and a 20-percent-chord split flap. Pressures were measured on both the upper and the lower surfaces of the main airfoil and the flaps for several angles of attack and at several flap settings. The data, presented as pressure diagrams and as graphs of the section coefficients for the flap alone and for the airfoil-flap combinations, are applicable to rib and flap design for a combination of a thick airfoil and a slotted or a split flap. The results of previous tests of a NACA 23012 airfoil with a slotted flap are compared with the present results.

Harris, Thomas A↗
NASA NTRS1942

Wind-tunnel investigation of an NACA 23012 airfoil with 30 percent-chord venetian-blind flaps

Report presents the results of an investigation made in the NACA 7 by 10-foot wind tunnel of a NACA 23012 airfoil with 30-percent-chord venetian-blind flaps having one, two, three, and four slats of Clark y section. The three-slat arrangements was aerodynamically the best of those tested but showed practically no improvement over the comparable arrangement used in the preliminary tests published in NACA Technical Report No. 689. The multiple-slat flaps gave slightly higher lift coefficients than the one-slat (Fowler) flap but gave considerably greater pitching-moment coefficients. An analysis of test data indicates that substitution of a thicker and more cambered section for the Clark y slats should improve the aerodynamic and the structural characteristics of the venetian-blind flap.

Rogallo, F M↗
NASA NTRS1948

Theoretical and experimental data for a number of NACA 6A-series airfoil sections

The NACA 6a-series airfoil sections were designed to eliminate the trailing-edge cusp which is characteristic of the NACA 6a-series sections. Theoretical data are presented for NACA 6a-series basic thickness forms having the position of minimum pressure of 30, 40, and 50 percent chord and with thickness ratios varying from 6 percent to 15 percent. Also presented are data for a mean line designed to maintain straight sides on the cambered sections.

Loftin, Laurence K , Jr↗
NASA NTRS1957

An Investigation of Single- and Dual-Rotation Propellers at Positive and Negative Thrust, and in Combination with an NACA 1-series D-Type Cowling at Mach Numbers up to 0.84

An investigation has been made to determine the aerodynamic characteristics of the NACA 4-(5)(05)-041 four-blade, single-relation propeller and the NACA 4-(5)(05)-037 six- and eight-blade, dual-rotation propellers in combination with various spinners and NACA d-type spinner-cowling combinations at Mach numbers up to 0.84. Propeller force characteristics, local velocity distributions in the propeller planes, inlet pressure recoveries, and static-pressure distributions on the cowling surfaces were measured for a wide range of blade angles, advance ratios, and inlet-velocity ratios. Included are data showing: (a) the effect of extended cylindrical spinners on the characteristics of the single-rotation propeller, (b) the effect of variation of the difference in blade angle setting between the front and rear components of the dual-rotation propellers, (c) the negative- and static-thrust characteristics of the propellers with 1 series spinners, and (d) the effects of ideal- and platform-type propeller-spinner junctures on the pressure-recovery characteristics of the single-rotation propeller-spinner-cowling combination.

Reynolds, Robert M↗
NASA NTRS1953

NACA Conference on aerodynamics of high-speed aircraft

This document contains unedited reproductions of technical papers on some of the most recent research results on the aerodynamics of high-speed aircraft from the NACA Laboratories. These papers were presented by members of the staff of the NACA Laboratories at the NACA Conference held at the Ames Aeronautical Laboratory July 8-10, 1953. The primary purpose of this conference was to convey to contractors of the military services and others concerned with the design of aircraft these recent research results and to provide those attending an opportunity to discuss the results.

Source record↗
NASA NTRS1996

A Wind Tunnel Investigation of Three NACA 1-Series Inlets at Mach Numbers up to 0.92

Pressure distributions on three NACA 1-series inlets have been obtained in the Langley 16-Foot Transonic Tunnel. The cowl diameter ratio (ratio of cowl highlight diameter to cowl maximum diameter) was 0.85 for all three inlets. The cowl length ratio (ratio of cowl length to cowl maximum diameter) was 1.0 for two of the inlets (NACA 1-85-100) and 0.439 for the other (NACA 1-85-43.9) inlet. One of the inlets with a cowl length ratio of 1.0 had an internal contraction ratio (ratio of highlight area to throat area) of 1.009 and the other had a contraction ratio of 1.250. The inlet with a cowl length ratio of 0.439 also had an internal contraction ratio of 1.250. All three inlets had longitudinal rows of static pressure orifices on the top and bottom external cowl surfaces. The inlet with a contraction ratio of 1.009 also had a row of static pressure orifices on the side of the cowl (external surface). The two inlets with a contraction ratio of 1.250 had a longitudinal row of static pressure orifices on the diffuser surface.

Re, Richard J.↗
NASA NTRS2000

Separating the from the Imagined: Flight Research at the NACA and NASA, 1915-1998

One of the most important, but under-appreciated, aspects of the NACA/NASA mission is its aeronautical R&D efforts. Within a short time of the first flight of the Wright brothers in 1903, the United States government recognized the importance of fostering development in the new and critical field of aeronautics. NASA's predecessor, the National Advisory Committee for Aeronautics (NACA), was chartered by Congress in 1915 specifically "to supervise and direct the scientific study of the problems of flight, with a view to their practical solution. " This became an enormously important government research and development activity for the next half century, materially enhancing the development of aeronautics 'in America. The results of the NACA's research appeared in more than 16,000 research reports of one type or another, distributed widely for the benefit of all. Many of the reports documenting R&D conducted under NACA auspices are still being used today. Since the creation of NASA in 1958, the critical R&D function has continued but is not well known. This work documents the historical R&D program of the agency by focusing on flight research.

Gorn, Michael H.↗
NASA NTRS1997

Desktop Access to Full-Text NACA and NASA Reports: Systems Developed by NASA Langley Technical Library

NASA Langley Technical Library has been involved in developing systems for full-text information delivery of NACA/NASA technical reports since 1991. This paper will describe the two prototypes it has developed and the present production system configuration. The prototype systems are a NACA CD-ROM of thirty-three classic paper NACA reports and a network-based Full-text Electronic Reports Documents System (FEDS) constructed from both paper and electronic formats of NACA and NASA reports. The production system is the DigiDoc System (DIGItal Documents) presently being developed based on the experiences gained from the two prototypes. DigiDoc configuration integrates the on-line catalog database World Wide Web interface and PDF technology to provide a powerful and flexible search and retrieval system. It describes in detail significant achievements and lessons learned in terms of data conversion, storage technologies, full-text searching and retrieval, and image databases. The conclusions from the experiences of digitization and full- text access and future plans for DigiDoc system implementation are discussed.

Ambur, Manjula Y.↗
NASA NTRS1941

Wind-Tunnel Investigation of an NACA 66,2-216 Low-Drag Wing with Split Flaps of Various Sizes, Special Report

An investigation was conducted in the NACA 19-foot pressure wind tunnel of a rectangular wing having NACA 66, 2-216 low-drag airfoil sections and various sizes of simple split flaps. The purpose of the investigation was, primarily, to determine the influence of these flap installations on the aerodynamic characteristics of the wing. Complete lift, drag, and pitching-moment characteristics were determined for a range of test Reynolds numbers from about 2,600,000 to 4,600,000 for each of the installations and for the plain wing. The results of this investigation indicate that values of maximum lift coefficient similar to those of wings with conventional airfoil sections and split flaps can be expected of wings having the NACA 66,2-216 low-drag sections. The increment of maximum lift due to the split flap was found to be practically independent of the Reynolds number over the range investigated. The optimum split flap on the basis of maximum lift appears to have a chord about 20% of the wing chord and a deflection of 60 degrees. The C(sub L) max of the wing with the 0.20c partial-span flap deflected 60 degrees is 2.07 at a Reynolds number of 4,600,000 while with the full-span flap it is approximately 2.53; the increment of the maximum lift coefficient due to the flap is approximately proportional to the flap span. Although the addition of a split flap tends to hasten the stall and to cause it to occur more abruptly, little change in pattern is evidenced by observations of the behavior of wool tufts on the wing.

Muse, Thomas C.↗