Search NASA⌕ Search

SEARCH · Search NASA

Results for “NYLON”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A critical review on the progress and challenges to a more sustainable, cost competitive synthesis of adipic acid

Adipic acid is a key organic diacid intermediate used in nylon manufacturing. It is primarily produced by an industrial process that can form nitrous oxide as a byproduct. Nitrous oxide has a 300-fold higher global warming potential than carbon dioxide, and an estimated 10% of its annual global emissions are a result of adipic acid production. These concerns have led to significant efforts for the development of nitrous oxide mitigation technologies as well as more environmentally friendly routes for adipic acid production. New processes include both advanced chemical and biotechnological routes. Here in this review, we discuss key recent developments in mitigation as well as new technologies. We also provide a critical look at the potential of new technologies to compete with the incumbent process and highlight key remaining technical challenges to the development of greener (environmentally sustainable) and cost competitive (commercially sustainable) processes for adipic acid manufacture.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2023

Chemical recycling of polymer composites induced by selective variable frequency microwave heating

Abstract The application of variable frequency microwave (VFM) heating to achieve rapid thermal depolymerization of polymer composites is reported for the first time. The thermal and chemical influence of composite additives on polymer decomposition has been studied for a set of chemically recyclable polymers, including polyphthalaldehyde, polypropylene carbonate, two polyhydroxyalkanoates, and nylon 6. Carbon‐based additives, specifically nanocarbon particles, were used as effective microwave absorbers to controllably degrade the surrounding polymer matrix into valuable, monomeric compounds. Depolymerization and byproduct confirmation were quantified by gel permeation chromatography and nuclear magnetic resonance spectroscopy. Synergistic effects can be leveraged from pre‐treating composite samples to further reduce the total microwave energy required to depolymerize composite samples. This study establishes the use of VFM heating for chemical recycling of polymer composites that can be leveraged toward a plastic circular economy.

Polymer Science↗
DOE OSTI2025

Self‐Standing Carbon Nanofibers@Carbon Felt Electrodes to Boost Electrolyzer Productivity: Application to the Electro‐Manufacturing of trans ‐3‐Hexenedioic Acid and Adipic Acid

The industrial implementation of electrosynthesis for chemical manufacturing remains constrained by the limited surface area of conventional electrodes. Herein, this challenge is addressed by designing a carbon nanofiber@carbon felt (CNF@CF) electrode platform that combines the high conductivity, flexibility, and ease of handling of commercial carbon felts (CF) with the large surface area and tunable surface chemistry of carbon nanofibers (CNFs). CNFs are deliberately grown onto the CF scaffold to form a sword-in-sheath structure, where entangled nanofibers wrap the felt macrofibers to provide excellent mechanical stability and electrical conductivity without binders. CNF@CF is evaluated both as an electrode and as a catalyst support for the electrochemical hydrogenation of cis,cis-muconic acid (ccMA), a biobased platform molecule key to the production of performance polyamides and renewable Nylon 6,6. As a noncatalytic electrode for the partial hydrogenation to trans-3-hexenedioic acid, CNF@CF achieves a threefold increase in both cumulative productivity and Faradaic efficiency (FE) compared to bare CF. A similar boost in catalytic activity and energy efficiency is observed using Pd/CNF@CF for the hydrogenation of ccMA to adipic acid. These results highlight the opportunities of the CNF@CF platform for electro-organic synthesis and sustainable chemical manufacturing.

electrochemical hydrogenation↗
DOE OSTI2022

Surface analysis insight note: Differentiation methods applicable to noisy data for determination of sp2‐ versus sp3‐hybridization of carbon allotropes and AES signal strengths

The derivatives of the spectra are commonly used for quantification in Auger Electron Spectroscopy (AES) spectra, while the derivative of the KLL C Auger line has proven to be valuable in obtaining a measure of the relative proportions of sp 2 ‐ and sp 3 ‐hybridization using the D‐parameter in both AES and X‐ray Photoelectron Spectroscopy (XPS). Differentiation of X‐ray Photoelectron Spectroscopy (XPS) and Auger Electron Spectroscopy (AES) spectra by numerical means is presented and illustrated for polymeric, such as PEEK and Nylon, as well as for graphitic materials including highly ordered pyrolytic graphite and graphene oxide. The most commonly available Savitzky–Golay method is explained mathematically and developed through the case of constructing a 5‐point quadratic polynomial convolution kernel suitable for differentiating spectra of adequate signal to noise. The concept of differentiation of spectra where signal to noise is less than adequate is also developed. Two alternative strategies to Savitzky–Golay differentiation are presented, which fit curves to data that allow derivatives to be obtained where Savitzky–Golay would otherwise fail. These alternative methods involve constructing a parametric curve that fits data over the entire energy interval of interest. Derivatives of spectra are then obtained by differentiating these parametric curves directly. A comparison of results for different materials for which specific sp 2 ‐ vs sp 3 ‐hybridized carbon proportions are of interest is used to emphasize the importance of characterizing methods used to differentiate spectra and understanding the characteristics of instrumentation used to measure spectra. The case for using Principal Component Analysis noise reduction with C KLL spectra is made for spectra collected from a heterogeneous graphene oxide sample.

Fairley, Neal↗
DOE OSTI2023

Plastic Laminate Antireflective Coatings for Millimeter-Wave Optics in BICEP Array

The BICEP/Keck series of experiments target the cosmic microwave background at degree-scale resolution from the South Pole. Over the next few years, the “Stage-3” BICEP Array (BA) telescope will improve the program’s frequency coverage and sensitivity to primordial B-mode polarization by an order of magnitude. The first receiver in the array, BA1, began observing at 30/40 GHz in early 2020. The next two receivers, BA2 and BA3, are currently being assembled and will map the southern sky at frequencies ranging from 95 to 150 GHz. Common to all BA receivers is a refractive, on-axis, cryogenic optical design that focuses microwave radiation onto a focal plane populated with antenna-coupled bolometers. High-performance antireflective coatings up to 760 mm in aperture are needed for each element in the optical chain, and must withstand repeated thermal cycles down to 4 K. Here, in this work, we present the design and fabrication of the 30/40 GHz anti-reflection coatings for the recently deployed BA1 receiver, with indices matched to its various polyethylene, nylon and alumina optical components. We describe an epoxy coating technique designed for alumina optics, which achieves better than 80% transmission at room temperature. For polyethylene optical elements, we present a new heat-compression approach that allows low-density polytetrafluoroethylene AR layers to reach sub-percent reflected power. We describe the planned use of these methods for the next BA cryostats, which may inform technological choices for future small-aperture telescopes of the CMB-S4 experiment.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Printing polymer blends through in situ active mixing during fused filament fabrication

Fused filament fabrication (FFF) enables production of 3D objects over a range of material compositions at low-cost relative to traditional manufacturing approaches. To date, a limited but growing number of materials are able to be used with FFF, however many applications exist where specific mechanical, thermal, or chemical properties are needed that cannot currently be met with the available feedstock selection. Therefore, a need exists to tune these materials for specific chemical or mechanical properties. One common formulation strategy to address these demanding design parameters is to develop composites or polymer blend filaments. Typically, this is a time-consuming and costly optimization process. Here, we have developed hardware for reproducibly mixing two filaments of similar or dissimilar compositions at the time of printing within individual printed layers. This mixing occurs via software-controlled rotating hardware in the chamber of an extruder’s hot-end. The efficiency of mixing within the printed layers has been characterized in detail as a function of the rotational speed and geometry of the blending hardware. These parameters were exploited to program the ratio and distribution of thermoplastic-based filaments blended within printed extrudate. Example printed specimens were produced with thermoplastic polyurethane (TPU) elastomer blended with rigid polylactic acid (PLA) and Nylon blended with PLA. In addition, a conductive carbon nanotube (CNT)-PLA composite was blended as a function of mixer geometry and input feed ratios with non-conductive PLA and resistance values were measured across the resulting printed specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multiscale porosity characterization in additively manufactured polymer nanocomposites using micro-computed tomography

Extrusion-based additive manufacturing (AM) of polymer composites exhibits complex thermally driven phenomena that introduce severe discontinuities in the internal structure across length scales, especially voids or porosity. This study utilizes a high-throughput porosity characterization technique to analyze large datasets from numerous micro-computed tomography (mu CT) scans to capture the influence of AM print parameters on the size, shape, and location of porosity across multiple print layers (up to a few cm) on fused granular fabrication (FGF) printers. The materials investigated include nanocomposite formulations based on commercially relevant nylon-12 and polyether ketone ketone (PEKK) materials comprising nano- or micro- sized fillers. The estimated global porosity follows an inverse linear correlation against the bulk density of the printed samples. Increasing the extrusion multiplier (EM) and the nozzle temperature while decreasing the print speeds reduces the global porosity. Outlier analyses (local porosity morphology) show that faster print speeds and higher extrusion rates result in long, slender inter-layer voids, while lower nozzle temperatures lead to large, symmetrical, inter-bead voids (at the bead junction). Lack of active chamber temperature increases inter-layer and intra-bead voids with a two-fold increase in global porosity. Overall, the micro filler-reinforced composites exhibit higher global porosity than nanofiller-reinforced composites, which is attributed to the increased mismatch in the thermal expansion coefficient between the filler and the polymers used in the study.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High compressive energy absorption and shape recovery behavior of additively manufactured textile-inspired cylindrical braided metamaterials

Mechanical metamaterials (MMs) are engineered structures with unique mechanical properties that arise from their unique spatial arrangement or lattice-like structure. The most commonly designed MMs such as honeycomb and re-entrant auxetics are prone to failure at the sharp corners and weak joints due to the increased stress concentration under deformation. To mitigate this challenge, braided MM structures involving intertwining threads of nylon—forming curved unit cells—have been studied. These textile-inspired cylindrical braided metamaterials (CBMMs) with contrasting unit cells, namely diamond and regular CBMMs, were fabricated by 3D printing. The layer-by-layer deposited structure built by fused filament fabrication delivered an assembly of overlapped threads that are fused at the contact point. To understand deformation behavior of these MMs, finite element models were developed for various load scenarios including quasi-static compression, cyclic and creep loads at room temperature. Stress distribution, deformation mechanisms, and failure modes were analyzed and validated by experiments to analyze the geometries and associated performance. The diamond CBMMs showed stress softening at 30 % compressive strain, withstanding a load of ∼440 N, whereas the regular CBMMs at 50 % strain experienced ∼250 N. The diamond CBMMs delivered higher creep resistance under sustained load and better energy absorption under cyclic loading than the regular CBMMs. The latter, however, exhibited 94 % shape recovery in contrast to 88 % recovery in former prototype during their first cyclic load. In conclusion, this study helps design mechanical lightweight devices that endure significant sustained load and exhibit enhanced energy absorption and shape recovery characteristics in cyclic loading.

Creep↗
DOE OSTI2023

Muconic acid production from algae hydrolysate as a high-value co-product of an algae biorefinery

Muconic acid is an attractive bio-derived product because it can be easily converted to adipic acid, a high-value and high-volume monomer used in the production of nylon and other valuable consumer plastics. As such, production of muconic acid from algae hydrolysate was explored to expand the suite of products available from algal biomass. Here we have established initial performance parameters and have shown that the range of substrates present in algae hydrolysate that are consumed by Pseudomonas putida includes at least glucose, mannose, glycerol, acetic acid, and lactic acid. We achieved complete utilization of these major carbon sources found in Scenedesmus acutus hydrolysate with a maximum muconic acid productivity of 0.25 g/L h. Final titer was 13.0 g/L (27% molar process yield) at approximately 50 h. In addition, algae hydrolysate does not require any additional nutrients to achieve these performance metrics. Techno-economic analysis showed the potential to support up to 150 algal biorefineries at this yield with significant greenhouse gas reductions.

09 BIOMASS FUELS↗
DOE OSTI2020

Toward hydrogen economy: Selective guaiacol hydrogenolysis under ambient hydrogen pressure

The conversion of guaiacol into the nylon precursors, cyclohexanol and cyclohexanone, is catalyzed by palladium supported on high surface area ceria (Pd/HS CeO 2 ) under mild conditions (100 °C, ≤1 bar H 2 ) via sequential hydrodemethoxylation and hydrogenation. In contrast, the 2-methoxycyclohexanol side product is generated by direct guaiacol hydrogenation. Reaction selectivity is determined by competing CO bond hydrogenolysis versus arene hydrogenation. Hydrogenolysis selectivity increases as H 2 pressure decreases, and over 80 % H 2 is incorporated into the products at 1 bar H 2 . Higher reactivity of guaiacol than anisole implies that the hydroxyl group is essential in Pd/HS CeO 2 catalysis. Participation of water in the conversion is evidenced by deuterium incorporation at non-exchangeable positions when the reaction is performed in D 2 O. Here, the combination of near quantitative mass balance of H 2 , high recyclability, and use of water as a solvent offers a simple, green and efficient conversion of lignin-derived aromatics into commercial products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Rational design of semi-interpenetrating network based on hyperbranched polyglycerol grafted MXene/polyurethane–epoxy for compressed hydrogen storage

Here, hydrogen (H 2 ) energy has emerged as a promising alternative in the automotive sector to replace fossil fuel; however, its storage with volumetric efficiency remains a challenge. The latest type IV storage vessel featuring a polymeric liner with composite overwrap incurs hydrogen saturation, which eventually causes failure. To prevent the H 2 dissolution in the liner, we have developed a barrier coating comprised of polyurethane/epoxy semi-interpenetrating network (S-IPN) combined with hyperbranched polyglycerol grafted MXene (h-MXene). The hyperbranched structure facilitated the dispersion of MXene in the coating solution by enhancing the exfoliation and improved the polymer filler interaction by forming covalent and H-bonding through end-terminal hydroxyl groups. Leveraging the dense network of S-IPN combined with the dispersed layer structured h-MXene significantly increased the tortuosity of the spray-coated barrier film applied to the nylon 6 liner. The coating exhibited a 90 % reduction in the H 2 gas permeability at only 2 wt% h-MXene concentration, which further improved to above 98 % at 10 wt% loading. Additionally, the h-MXene considerably improved the adhesion with the liner even in a highly stretched condition, signifying the durability of the coating under cyclic pressurization and depressurization of the storage vessel.

08 HYDROGEN↗
DOE OSTI2025

Development of fiber orientation in injection molding: Comparison of glass fiber, carbon fiber and their hybrid composites

Fiber orientation distribution (FOD) in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for glass fiber (GF), carbon fiber (CF), and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varied with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of chemical stabilities and contact angle of 3D printed polymers with CO 2 capture solvents to enhance absorber performance

Increasing absorption rate in aqueous amine CCS systems is one avenue to decrease capital cost by reducing the overall size of the absorber column. One potential route is by replacing conventional steel packing with custom designed packing made from 3D printed polymers. 3D printing offers endless flexibility in packing designs to better enhance liquid/gas contact, increase CO 2 mass transfer and create compact absorber columns. Additionally, before exploring novel packing designs, it is necessary to identify polymer materials that can be 3D printed while also showing long-term physical and surface property stability upon exposure to corrosive amine solutions. Four polymers that are commonly used for 3D printing were evaluated using CO 2 -loaded amine solution at temperatures typically observed in the absorber column. Three polymers, high-density polystyrene (HDPS), acrylonitrile butadiene styrene (ABS) and nylon were found to be physically stable after 5000 hr of amine exposure at temperatures up to 60 °C. The contact angle (wetting) of water and CO 2 -loaded aqueous amine solution on the polymer surfaces were also stable after exposure to the CO2-loaded amine solution.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effects of magnetic field annealing on the hard magnetic properties of milled Nd-Fe-B powders

In this study, we report the effect of magnetic field annealing (MA) in relieving the stress induced during the milling of Nd-Fe-B sintered magnets. The effect of MA processing parameters and particle size on the magnetic properties were investigated. Based on the results, magnetic field annealing is more effective in improving the magnetic properties of larger size particles, compared to finer particles. Our computational study on the role of particle surface defects in bi-modal particle distribution agrees with results obtained experimentally. In conclusion, magnetic field annealed powder has been successfully used to develop 4.6 g.cm -3 density bonded magnets with 75 vol% of magnetic powder and polyamide 12 (nylon 12) polymer binder resulting in 11.3 MGOe energy product.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Recycling of additively printed anisotropic Nd-Fe-B bonded magnets

A high potential cost-effective and environmentally friendly method has been applied for recycling anisotropic Nd-Fe-B bonded magnets. Waste additively printed Hydrogenation-Disproportionation-Desorption-Recombination (HDDR) Nd-Fe-B anisotropic bonded magnet was pulverized into composite powder containing Nd-Fe-B particles and nylon binder through cryomilling at a liquid nitrogen temperature (~77 K) under Ar inert atmosphere. Then, the cryomilled composite powder was warm compacted into a bonded magnet. Further, the magnetic particles were aligned during post-compaction annealing under a magnetic field of 30 kOe. The recycled bonded magnets have a higher density (3% enhancement), but slightly inferior magnetic properties compared to the original magnets, i.e., the magnetic remanence, coercivity and maximum energy product are reduced by 2%, 3% and 8%, respectively. The scanning electron microscopy revealed that some HDDR Nd-Fe-B powder crumbled into fine particles during cryomilling. Powder X-ray diffraction showed a small amount of Nd-oxide impurity in the cryomilled powder. The slightly deteriorated magnetic properties are ascribed to the oxidation of Nd-Fe-B particles due to formation of fresh fracture surface during cryomilling. The approach enables the direct reuse of end-of-life bonded magnets in an economical and environmentally friendly way.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic and single cell characterization of a CRISPR-interference toolset in Pseudomonas putida KT2440 for β-ketoadipate production from p -coumarate

We report Pseudomonas putida KT2440 is a well-studied bacterium for the conversion of lignin-derived aromatic compounds to bioproducts. The development of advanced genetic tools in P. putida has reduced the turnaround time for hypothesis testing and enabled the construction of strains capable of producing various products of interest. Here, we evaluate an inducible CRISPR-interference (CRISPRi) toolset on fluorescent, essential, and metabolic targets. Nuclease-deficient Cas9 (dCas9) expressed with the arabinose (8K)-inducible promoter was shown to be tightly regulated across various media conditions and when targeting essential genes. In addition to bulk growth data, single cell time lapse microscopy was conducted, which revealed intrinsic heterogeneity in knockdown rate within an isoclonal population. The dynamics of knockdown were studied across genomic targets in exponentially-growing cells, revealing a universal 1.75 ± 0.38 hour quiescent phase after induction where 1.5 ± 0.35 doublings occur before a phenotypic response is observed. To demonstrate application of this CRISPRi toolset, β-ketoadipate, a monomer for performance-advantaged nylon, was produced at a 4.39 ± 0.5 g/L and yield of 0.76 ± 0.10 mol/mol from p-coumarate, a hydroxycinnamic acid that can be derived from grasses. These cultivation metrics were achieved by using the higher strength IPTG (1K)-inducible promoter to knockdown the pcaIJ operon in the βKA pathway during early exponential phase. This allowed the majority of the carbon to be shunted into the desired product while eliminating the need for a supplemental carbon and energy source to support growth and maintenance.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

In situ oxidation of reduced graphene oxide membranes by peracetic acid for dye desalination

Graphene oxide (GO) membranes with tunable interlayer spacings are of interest for dye removal from salty textile wastewater, and the membranes are often reduced to improve their stability, which inevitably lowers water permeance. Herein, we demonstrate that reduced GO (rGO) membranes can be facilely modified using peracetic acid (PAA) in situ to dramatically enhance water permeance while retaining dye rejection. Specifically, PAA-modified membranes (PrGO) are synthesized by vacuum-filtering hydrazine-reduced rGO nanosheets onto Nylon substrate and then exposing them to PAA solutions. The effects of the rGO layer thickness, PAA content, and PAA exposure time on the membrane chemistry, nanostructures, and salt/dye separation properties are thoroughly examined. For example, the PAA oxidation of a 100 nm-thick rGO membrane for 10 min increases water permeance by 180 %, from 35 to 93 Liter m −2 h −1 bar −1 , and decreases Na 2 SO 4 rejection from 10 % to 3.3 % while retaining the rejection of Congo red at ≈99.7 %. The PrGO membranes exhibit stable water permeance and >99 % dye rejection in multi-cycle tests in a crossflow system, surpassing state-of-the-art GO membranes and showcasing their potential for practical applications.

Dye desalination↗
DOE OSTI2024

N 2 O deconstruction of polycyclooctene to generate carbonyl-functionalized macromonomers

Deconstruction of polyolefins into functionalized macromonomers presents a compelling strategy for polyolefin upcycling by creating macromonomers through dehydrogenation/depolymerization. We show that nitrous oxide (N 2 O), a greenhouse gas waste product from the production of nylon, mediates the deconstruction of polycyclooctene (PCOE) and generates carbonyl-functionalized macromonomers. Carbonyl incorporation and macromonomer molar mass were well controlled by reaction time, and subsequent hydrogenation readily removed residual carbon-carbon double bonds. Here, we also demonstrated that the reaction could progress efficiently with substrates of moderate levels of unsaturation, closely mimicking partially dehydrogenated polyethylene. Such carbonyl-functionalized macromonomers could serve as feedstock for preparing vitrimers and other functional polymers.

36 MATERIALS SCIENCE↗