Search NASA⌕ Search

SEARCH · Search NASA

Results for “Nanoindentation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Origin of strain softening in a nanograined Al alloy

Here, one-step and multi-step nanoindentation experiments were conducted to investigate the mechanical response of an Al-Mg-Li alloy. Opposite to the strain hardening effect observed in the coarse-grained (CG) alloy, the nanograined (NG) alloy exhibits strain softening. Compared with multi-step nanoindentation experiments, the ultralow dislocation density and the grain boundary (GB) segregation promote a higher stress level during one-step nanoindentation experiments. Residual perfect dislocations induced by a previous loading and unloading during multi-step nanoindentation experiments lower the stress required for further plastic deformation. In addition, the storage of partial dislocations also serves to render plastic flow to commence at lower stresses. This work provides new insights for the fabrication and property optimization of NG alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Chemo-Mechanics of α-V 2 O 5 During Lithiation and Implications for Rechargeable Battery Cathodes

Chemo-mechanical degradation of layered oxide electrodes is strongly influenced by crystallographic anisotropy, local stress evolution, and ion insertion, yet the intrinsic mechanical response of layered materials remains incompletely understood. Indeed, most prior studies have focused on polycrystalline materials but single crystals enable direct observation of coupling between anisotropic ion diffusion and mechanical response. This study aims to determine how crystallographic anisotropy and lithiation affect deformation, fracture, and mechanical properties in single-crystal V 2 O 5 , and compares this behavior with polycrystalline counterparts. Polycrystalline V 2 O 5 thin films and single-crystal α-V 2 O 5 were studied using nanoindentation, scanning electron microscopy, focused ion beam cross-sectioning, and Raman spectroscopy. Single crystals were tested in pristine and chemically lithiated states, including experiments in which crystals were first plastically deformed via nanoindentation and subsequently lithiated. Polycrystalline films exhibited significantly higher hardness and elastic modulus than single crystals. Single crystals indented normal to the exposed (001) basal plane exhibited pronounced anisotropic deformation, including directional slip, crystallographically-guided cracking, anisotropic crack propagation, interlayer separation, and shear localization. Lithiation caused substantial softening, reduced hardness and modulus, and suppressed displacement bursts during nanoindentation, while previously indented regions showed crack formation and growth upon lithiation. Mechanical behavior of α-V 2 O 5 is strongly governed by crystallographic anisotropy and further altered by lithiation, with pre-existing deformation serving as a strong driver of fracture during ion insertion. These findings illuminate the coupling among ion insertion, deformation, and fracture in layered oxides and provide a basis for understanding and mitigating mechanical failure in electrochemical energy-storage materials.

Anisotropy↗
DOE OSTI2020

Indirectly probing the structural change in ion-irradiated Zr-Based metallic glasses from small scale mechanical tests

Ion irradiation was applied to tailor the structural heterogeneities in Zr-based metallic glasses at room temperature. Experimental methods of X-ray diffraction, nanoindentation, and micropillar compression were conducted to examine the irradiation effects on their structural and mechanical property changes. It is found that the irradiated materials retained amorphous structure after room-temperature Ni ion irradiation. The reduction of elastic modulus and hardness measured by nanoindentation indicated the irradiation-induced mechanical degradation. A unified statistic model was employed to quantitatively predict the density and strength of irradiation defects, although their specific structural and physical nature is not explicitly included in this model. The transition of non-intersecting shear bands to multiple intersecting shear bands was observed on compression tests of irradiated micropillars with the increase of irradiation dose. Furthermore, the analysis of the displacement excursion of micropillar compression tests indicated a different deformation mode from the unirradiated state. These results from nanoindentation pop-in and micro-pillar compression tests suggested that irradiation eventually leads to a new state with different types and characteristics of structural heterogeneities from violent displacement cascades and non-equilibrium energy deposition/dissipation processes, which also proves ion irradiation as an effective method to tune the structure and mechanical properties of metallic glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Alteration in micro-mechanical characteristics of wellbore cement fracture surfaces due to fluid exposure

The stiffness of wellbore cement fracture surfaces was measured after exposing to the advective flow of nitrogen, silicone oil, and medium sweet dead crude oil for different exposure periods. The test specimens were extracted from fractured cement cylinders, where the cement fracture surfaces were exposed to the different fluids up to 15 weeks. A nanoindenter with a Berkovich indenter tip was used to measure load-indentation depth data, which was used to extract the elastic modulus (E) and nano-hardness (H) of the cement fracture surfaces. A reduction in the elastic modulus compared with an unexposed specimen were observed in all the specimens. Both elastic modulus and nano-hardness for the specimens exposed to silicone oil were lower than specimens exposed to nitrogen gas and varied with the period of exposure. The elastic modulus and nano-hardness of the specimens exposed to crude oil were the lowest with a significant decrement with the exposure period. The frequency distribution of the nanoindentation measurements shows that the volume-fraction ratio of the two types of cement hydrated nanocomposites for both the unexposed and test specimens is about 70:30%. Phase transformation beneath the indenter is observed for all of the specimens, with more obvious plastic deformation in specimens exposed to crude oil. Analytical measurements (SEM, EDS, FT-IR, and XRD) on exposed cement fracture surfaces reveal different levels of physical and chemical alteration that are consistent with the reduction in stiffness measured by nanoindentation. Furthermore, the study suggests that cement stiffness will decrease due to crude oil exposure, and the fracture will be sensitive to stress and pore pressure with time.

42 ENGINEERING↗
DOE OSTI2021

Nanomechanical mapping and strain rate sensitivity of microcrystalline cellulose

Nanoindentation provides a convenient and high-throughput means for mapping mechanical properties and for measuring the strain rate sensitivity of a material. Here, nanoindentation was applied to the study of microcrystalline cellulose. Here, constant strain rate nanoindentation revealed a depth dependence of nanohardness and modulus, mostly attributed to material densification. Nanomechanical maps of storage modulus and hardness resolved the shape and size of voids present in larger particles. In smaller, denser particles, however, where storage modulus varied little spatially, there was still some spatial dependence of hardness, which can be explained by cellulose’s structural anisotropy. Additionally, hardness changed with the indentation strain rate in strain rate jump tests. The resulting strain rate sensitivity values were found to be in agreement with those obtained by other techniques in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Relation Between the Defect Interactions and the Serration Dynamics in a Zr-Based Bulk Metallic Glass

For this study, the effects of thermal annealing and compressive strain rate on the complexity of the serration behavior in a Zr-based bulk metallic glass (BMG) was investigated. Here, as-cast and thermally-annealed (300 °C, 1 week) Zr 52.5 Cu 17.9 Ni 14.6 Al 10 Ti 5 BMG underwent room-temperature compression tests in the unconstrained condition at strain rates of 2 × 10 -5 s -1 and 2 × 10 -4 s -1 . The complexity of the serrated flow was determined, using the refined composite multiscale entropy technique. Nanoindentation testing and X-ray diffraction characterization were performed to assess the changes in the microstructure and mechanical properties of the BMG that occurred during annealing. The results indicated that the BMG did not crystallize during annealing in the prescribed heating condition. Nanoindentation tests revealed that annealing led to a significant increase in the depth-dependent nanoindentation hardness and Young’s modulus, which were attributed to the structural relaxation in the glass. Furthermore, both annealing and an increased strain rate resulted in a marked enhancement in the complexity of the serrated flow during compression. It was concluded that the increase in the sample entropy with increasing strain rate is related to an increase in the number of defect interactions during the serrated flow.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Comparison of hardening and microstructures of ferritic/martensitic steels irradiated with fast neutrons and dual ions

Ferritic/martensitic steels T91 and HT9 were irradiated with neutrons (BOR-60 reactor) and dual ions (9 MeV Fe 3+ and 3.42 MeV energy degraded He 2+ ) from 369 to 520 °C and damage levels of 16.6 to 72 dpa to quantify the possibility of using ion irradiation to simulate neutron irradiation in terms of microstructures and mechanical properties. Nanoindentation testing was performed to obtain the bulk equivalent hardness of the dual-ion irradiated samples. For the neutron irradiated samples, both nanoindentation and Vickers hardness testing were conducted. Transmission Electron Microscopy (TEM) characterizations of the cavities, dislocation loops and precipitates were conducted to account for the strengthening contribution of each microstructure element. The good agreement between the microstructure-predicted (dispersed barrier hardening) and measured strength of the irradiated specimens demonstrated the accuracy of the strengthening model and the nanoindentation tests. Furthermore, the comparison of mechanical property and microstructure changes in ion and neutron irradiated structural materials indicated that ion irradiation replicated many neutron irradiation features. However, a single 70 °C temperature shift is insufficient to match all complex microstructures of neutron vs. ion irradiation over the irradiation temperature range of 369–520 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of irradiation damage on the hardness and elastic properties of quaternary and high entropy transition metal diborides

Multi-principal component transition metal (TM) diborides represent a class of high-entropy ceramics (HECs) that have received considerable interest in recent years owing to their promising properties for extreme environment applications that include thermal/ environmental barriers, hypersonic vehicles, turbine engines, and next-generation nuclear reactors. While the addition of chemical disorder through the random distribution of TM elements on the cation sublattice has offered opportunities to tailor elastic stiffness and hardness, the effects of irradiation-induced structural damage on the physical properties of these complex materials have remained largely unexplored. To this end, changes in the hardness and elastic moduli of a high-entropy TM diboride (Hf 0.2 Nb 0.2 Ta 0.2 Ti 0.2 Zr 0.2 )B 2 and three of its quaternary subsets following irradiation with 10 MeV gold (Au) ions to fluences of up to 6 × 10 15 Au cm -2 are investigated at the micrometer and sub-micrometer length-scales via the dispersion of laser-generated surface acoustic waves (SAW) and nanoindentation, respectively. The nanoindentation measurements show that the TM diborides exhibit an initial increase in hardness following irradiation with energetic Au ions, with a subsequent decrease in hardness following further irradiation. One quaternary composition, (Hf 1/3 Ta 1/3 Ti 1/3 )B 2 , exhibits a notable exception to the trend and continues to exhibit an increase in hardness with ion irradiation fluence. Although differences in the absolute values of the effective elastic moduli obtained from the measured SAW dispersion and nanoindentation are observed (and attributed to microstructural variations at the measurement length-scale), both techniques yield similar trends in the form of an initial reduction and subsequent saturation in the elastic modulus with increasing ion irradiation fluence. The quaternary TM diboride (Hf 1/3 Ta 1/3 Ti 1/3 )B 2 again exhibits a departure from this trend. The high-entropy TM diboride (Hf 0.2 Nb 0.2 Ta 0.2 Ti 0.2 Zr 0.2 )B 2 exhibits the greatest recovery in hardness and modulus when irradiated to high ion fluences following initial changes at low fluence, indicating superior resistance to radiation-induced damage over its quaternary counterparts. Opportunities for designing HECs with superior hardness and modulus for enhanced radiation resistance (compared to their single constituent counterparts) by tailoring chemical disorder and bond character in the lattice are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural and Micromechanical Characterization of FeCrAl C26M tubes

The present report summarizes the nanoindentation characterization of a FeCrAl alloy, C26M in both tube and bar form. The current heat, AC2-B, investigated by electron backscatter diffraction showed a textured system with the cross-section favoring orientations near the [110] and the tube surface near the [111], similar to previous heats of C26M. Nanoindentation with a Berkovich tip measured a similar moduli and hardness for all specimens of ~220 GPa and ~5 GPa, respectively. Spherical nanoindentation was performed on all specimens and orientations. Indentation with a 100 μm tip resulted in a measured moduli and yield strength values of ~215 GPa and ~1.5 GPa for all specimens, respectively, and in agreement with the Berkovich indentation results. Mesoscale tensile bars were laser cut out of a thin piece of AC2-B. Initial tensile testing showed that a minimum gauge thickness/width of 0.05 mm is required to approach more bulk-like conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Effects of irradiation damage on the elastic properties and hardness of complex transition metal diborides

Multi-principal component transition metal (TM) diborides represent a class of high-entropy ceramics (HECs) that have received considerable interest in recent years owing to their promising properties for extreme environment applications that include thermal/ environmental barriers, hypersonic vehicles, turbine engines, and next-generation nuclear reactors. While the addition of chemical disorder through the random distribution of TM elements on the cation sublattice has offered opportunities to tailor elastic stiffness and hardness, the effects of irradiationinduced structural damage on the physical properties of these complex materials have remained largely unexplored. To this end, changes in the hardness and elastic moduli of a high-entropy TM diboride (Hf0.2Nb0.2Ta0.2Ti0.2Zr0.2)B2 and three of its quaternary subsets following irradiation with 10 MeV gold (Au) ions to fluences of up to 6 × 10^15 Au cm-2 are investigated at the micrometer and sub-micrometer length-scales via the dispersion of laser-generated surface acoustic waves (SAW) and nanoindentation, respectively. The nanoindentation measurements show that the TM diborides exhibit an initial increase in hardness following irradiation with energetic Au ions, with a subsequent decrease in hardness following further irradiation. One quaternary composition, (Hf1/3Ta1/3Ti1/3)B2, exhibits a notable exception to the trend and continues to exhibit an increase in hardness with ion irradiation fluence. Although differences in the absolute values of the effective elastic moduli obtained from the measured SAW dispersion and nanoindentation are observed (and attributed to microstructural variations at the measurement length-scale), both techniques yield similar trends in the form of an initial reduction and subsequent saturation in the elastic modulus with increasing ion irradiation fluence. The quaternary TM diboride (Hf1/3Ta1/3Ti1/3)B2 again exhibits a departure from this trend. The high-entropy TM diboride (Hf0.2Nb0.2Ta0.2Ti0.2Zr0.2)B2 exhibits the greatest recovery in hardness and modulus when irradiated to high ion fluences following initial changes at low fluence, indicating superior resistance to radiation-induced damage over its quaternary counterparts. Opportunities for designing HECs with superior hardness and modulus for enhanced radiation resistance (compared to their single constituent counterparts) by tailoring chemical disorder and bond character in the lattice are discussed.

36 - MATERIALS SCIENCE↗
DOE OSTI2019

Investigation of the mechanical and microstructural evolution of a Cu based bulk metallic glass during ion irradiation

Ion irradiation and annealing experiments were performed on Cu 60 Zr 20 Hf 10 Ti 10 bulk metallic glass (BMG) specimens to investigate their irradiation- and temperature-induced microstructural and mechanical property evolution. For the ion irradiations, samples were exposed to 9 MeV Ni 3+ ions to a midrange (~1.2 μm depth) dose of 10 displacements per atom (dpa) at temperatures ranging from room temperature to 360 °C (the corresponding peak dose at ~2.8 μm depth was ~25 dpa). Bulk X-ray diffraction (XRD) and transmission electron microscopy (TEM) characterization revealed that the alloy did not crystallize during irradiation up to 290 °C but did partially crystallize at 360 °C. XRD analysis revealed that the crystallization which occurred in the sample irradiated at 360 °C was caused by thermal effects instead of irradiation displacement damage. Subsequent Rietveld refinement analysis of the XRD measurements revealed the presence of two distinct crystal phases, namely a CuTiZr hexagonal structure belonging to the P63/mmc space group and a CuTi tetragonal structure belonging to the P4/mmm space group. Nanoindentation experiments revealed that no pronounced hardness changes occurred in the specimens irradiated at room temperature and 290°C, although significant hardening was observed in the sample irradiated at 360 °C. The significant increase in the hardness at 360°C was ascribed to thermally induced partial crystallization of the alloy instead of the ion irradiation. In general, the results of the nanoindentation experiments and XRD characterization suggest that although the Cu BMG exhibits good stability during irradiation at temperatures up to 290 °C it is not suitable for irradiation environments where the temperature is 360 °C for extended periods of time. The Lam and Chong extrapolation method, which has been used to study the indentation size effect (ISE) in amorphous alloys, was employed to quantify how irradiation and temperature affect this type of behavior in the BMG. However, the poor linear fitting of the indentation hardness data by this model indicate that a new ISE model is likely needed to quantify indentation hardening in BMGs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Nanoscale serration characteristics of additively manufactured superalloys

Structural elements made of nickel-based superalloys usually operate at high temperatures. Many surface failure mechanisms such as creep, fatigue, fretting fatigue, corrosion, and stress corrosion cracking start from the surface. Thus, studying the surface mechanical properties and deformation behavior of materials is vital in order to draw a correlation between the surface properties and failures. Herein, a nanoindentation technique was implemented to characterize surface properties of a widely used additively manufactured (AM) superalloy, i.e., Inconel 625. The specimens were tested in a range of temperatures in a vacuum chamber. Serrated plastic flow characterized by pop-in events during nanoindentation, known as Portevin-Le Chatelier (PLC) effect, was observed in all three tested elevated temperatures. This phenomenon depicts itself as bursts of plasticity in the loading section of the load-displacement curves. These bursts were studied comprehensively to explore incipient plasticity. Hertzian contact mechanics were implemented to extract the maximum shear stress beneath the indenter from the pop-in loads. The results show that the initial pop-in load increases as the temperature increases. The average initial pop-in load increases by almost four times from 300 °C to 650 °C. This was attributed to the formation of strengthening precipitates. The average size of the serrations and the magnitude of dislocation nucleation increase from 300 °C to 500 °C and decrease from 500 °C to 650 °C. Finally, the serrations are attributed to the dislocation generation and movement as well as their interaction with the solute atoms and precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of irradiation spectrum on the microstructural and mechanical properties of bulk metallic glasses

Zr 52.5 Cu 17.9 Ni 14.6 Al 10 Ti 5 (BAM-11) and Cu60Zr 20 Hf 10 Ti 10 bulk metallic glass (BMG) specimens were ion irradiated to characterize and compare their irradiation induced microstructural and mechanical property evolution. For the ion irradiations, samples of each BMG were exposed to 9 MeV Ni 3+ and 5.5 MeV C + ions to a midrange (~1.5 μm depth) dose of 0.5 displacements per atom (dpa) at temperatures ranging from room temperature to 360 °C in order to examine potential effects associated with low (5.5 MeV C) and high (9 MeV Ni) average primary knock on energies. BAM-11 BMG samples were also irradiated by neutrons (E > 0.1 MeV) at ~70 °C to a fluence of 1.4 × 10 20 n/cm 2 (dose of 0.1 dpa). Importantly, no pronounced irradiation spectrum effects were observed for the nanoindentation mechanical properties of the two BMGs following ion irradiation. However, significant softening was observed in the BAM-11 BMG sample irradiated by neutrons, while annealing of the unirradiated samples led to a marked increase in hardening. Finally, results of the nanoindentation experiments indicate that softening is caused by irradiation induced creation of free volume defects, while the hardening is caused by their annihilation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tunable mechanical behavior of graphene nanoribbon-metal composites fabricated through an electrocharge-assisted process

This work investigates the role of a carbon nanophase on the local mechanical behavior of nanocarbon metal matrix composites (NCMCs) produced through an electrocharge-assisted process. Nanoindentation experiments on single crystal Al, Al 1350 parent alloys, and Al 1350 NCMCs revealed variable mechanical properties, caused by an interplay between microstructure and graphitic reinforcements. TEM and AFM studies also reveal nanoscale structural changes based on the incorporation of a carbon nanophase. In order to decouple the effects of the aforementioned mechanical behaviors, molecular dynamics nanoindentation simulations were performed on the (111) surface of Al and Al NCMC samples containing semi-infinite graphene nanoribbons to examine the evolution of plasticity over time. Findings indicate that the arrangement of a finite graphene nanophase within a host matrix can alter plasticity mechanisms and therefore yield strength in near-surface mechanical behavior with little effect on elastic properties. Here, this understanding enables further study into tunable bulk properties of Al-based NCMCs while isolating microstructural effects and reinforcement effects of the carbon phase. Such an understanding will lead to application-specific material geometries ranging from highperforming vehicle structures to next-generation electrical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Chromium enhances the mechanical performance of 3d transition metal high entropy alloys

A comprehensive examination of the compositional effects on the deformation behavior of high entropy alloys (HEAs) was conducted through nanoindentation, indentation creep, and stress relaxation experiments at ambient temperature. The alloys investigated included NiCoFe, NiCoCr, NiCoCrFe, and NiCoCrFeMn, all of which underwent identical thermomechanical processing. From the experimental results, NiCoCr exhibited the highest maximum shear stress for dislocation nucleation (13 GPa) and nanoindentation hardness (3.8 GPa) among the alloys tested. It also showed the lowest stress sensitivity (0.02) and activation volume (3–4 b 3 ) under creep and stress relaxation conditions, indicative of its superior plastic flow properties. Density functional theory (DFT) calculations further revealed an uneven charge density and larger bonding-length variation in NiCoCr due to the presence of Cr, which increased lattice distortion, impeding dislocation movement. Furthermore, in this study, post-deformation microscopy using transmission electron microscopy (TEM) revealed a high density of stacking faults and twins in NiCoCr that effectively enhanced its creep strength. The results highlight the significance of specific elemental effects, particularly from Cr in this study, over configurational entropy effect (i.e., compositional complexity) in governing the deformation microstructure and mechanical properties of HEAs. Finally, these insights will be instrumental for the design and optimization of advanced alloys for load-bearing applications.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural and nanomechanical studies of PVD Cr coatings on SiC for LWR fuel cladding applications

The microstructure and nanomechanical properties of pure Cr coatings deposited on SiC with various physical vapor deposition (PVD) methods have been investigated for the mitigation of hydrothermal corrosion of SiC-SiC f (SiC fiber-reinforced SiC matrix) composite fuel cladding in light water reactors (LWR). Cr coatings (4–7 μm thick) were deposited on unbiased SiC substrates using six variants of magnetron sputtering processes: (i) standard (S-DCMS), (ii) pulsed (P-DCMS), (iii) ion-assisted (I-DCMS), and (iv) pulsed ion-assisted direct current magnetron sputtering (PI-DCMS), (v) high-power impulse magnetron sputtering (HiPIMS), and (vi) bipolar HiPIMS (B-HiPIMS). Microstructural characterization and nanoindentation testing were used to evaluate effects of deposition technique on coating microstructure and nanomechanical properties. The application of positive reverse pulses to the sputter target induced coarsening of the columnar grain structure, while ion bombardment of substrates during deposition promoted densification of the coating microstructure. Both effects are exemplified in B-HiPIMS deposition, resulting in a high-density microstructure with compressive residual stress. Material pile-up around nano-indents and plastic work during nanoindentation were analyzed to understand deformation behavior of the coatings. Finally, the results suggest the B-HiPIMS process to be among the promising methods for the deposition of Cr coatings on SiC-SiC f for LWR cladding application.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanical and tribological properties of anodic Al coatings as a function of anodizing conditions

Enhanced wear and corrosion resistance properties are vital for numerous functional and decorative applications. Anodizing is a process frequently used to generate stable oxide coatings on metal surfaces, including aluminium (Al). In this work, we present an evaluation of process variables for optimized anodized coating properties using existing methods and as a baseline for novel coating development. A representative relatively pure Al alloy was chosen as a model system with a goal of finding conditions to achieve high wear coatings with retained ductility. AA5052 alloy coupons were anodized in two different electrolytes (sulfuric and phosphoric acid) to study the effects of anodizing conditions on the mechanical and tribological properties of the anodic coatings. Porosity was evaluated with microscopy, coating hardness was determined via nanoindentation, and tribological properties were characterized using a pin-on-disk tribometer. These measurements were correlated and a loading evaluation was performed to assess the optimum nanoindentation parameters for the use of representative coupons without the need for special processing prior to anodizing. The porosity and coating thickness were found to depend on the anodizing time and the type of electrolyte. Thicker and harder anodic coatings were generated in sulfuric acid compared to phosphoric acid. Porosity studies of the anodic coatings generated in phosphoric acid revealed that coating porosity decreased as the anodizing time increased. Both electrolytes generated anodic coatings with improved tribological properties (friction coefficient and dimensional wear rate), and an optimum processing time was identified for best wear properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Water Weakening of Calcium Oxide

Chemomechanical processes such as water weakening can control the permeability and deformation of rocks and manmade materials. Here, atomistic modeling and nanomechanical experiments were used to identify molecular origins of chemomechanical effects in calcium oxide (CaO) and its effect on observed elastic, plastic, and brittle deformation. Classical molecular dynamics simulations with the bond order-based reactive force-field ReaxFF were used to assess brittle fracture. In the presence of water, CaO fractured earlier and more often during quasi-static loading, with a calculated reduction in fracture toughness of ~80% associated with changes in the stress distribution around the crack tip. Experimentally, elastic and plastic deformation of CaO surfaces exposed to water was assessed experimentally using in situ liquid nanoindentation. Nanoindentation showed that following exposure to water, the contact hardness decreased by 1–2 orders of magnitude and decreased the modulus by 2–3 orders of magnitude due to surface hydroxylation. Furthermore, the strong chemomechanical effects on the mechanical processes in CaO suggests that minerals with similar structures may exhibit comparable effects, influencing the stability of cements and geomaterials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗