Search NASA⌕ Search

SEARCH · Search NASA

Results for “OSU”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Free geometric adjustment of the OSU/NGSP global network /solution WN-4/

The paper presents the results of the OSU WN 4 geometric adjustment for the coordinates of 152 satellite tracking stations. The results, when referred to the WN 4 ellipsoid of a = 6,378,127.8 m and 1/f = 298.25 produce geoid undulations consistent with dynamically determined ones. The average standard deviation in a Cartesian coordinate is plus or minus 4.0 m; in height, plus or minus 2.7 m. Comparisons with coordinates obtained from dynamic solutions show significant inconsistencies in the orientation of the coordinate systems.

Mueller, I. I.↗
NASA NTRS1977

Improved ground truth geoid for the GEOS-3 calibration area

The purpose of this investigation is to develop methods and procedures are reported for computing a detailed geoid to be used as geodetic ground truth for the calibration and verification of GEOS-3 altimeter data. The technique developed is based on rectifying the best available detailed geoid so that the rectified geoid will have correct scale, orientation, shape and position with respect to the geocenter. The approach involved the development of a mathematical model based on a second degree polynomial, in rectangular Cartesian coordinates, describing the geoid undulations at the control stations. A generalized least squares solution was obtained for the polynomial which describes the variation of the undulation differences between the control stations geoid and the gravimetric geoid. Three rectified geoid were determined. These geoids correspond to three sets of tracking station data: (1) WFC/C-band data; (2) GSFC/C-band data; and (3) OSU-275 data. The absolute accuracy of these rectified geoids is linearly correlated with the uncertainties of the tracking station coordinates and, to a certain extent, with those of the detailed geoid being rectified.

Mourad, A. G.↗
NASA NTRS1975

Satellite triangulation in Europe from WEST and ISAGEX data

Observational data that was acquired during the West European Satellite Triangulation (WEST) program and the International Satellite Geodesy Experiment (ISAGEX) campaign was obtained for the purpose of performing a geometric solution to improve the present values of coordinates of the European stations in the OSU WN14 solutions, adding some new stations and assessing the quality of the WN14 solution with the help of the additional data available. The status of the data as received, the preprocessing required and the preliminary tests carried out for the initial screening of the data are described. The adjustment computations carried out and the results of the adjustments are discussed.

Leick, A.↗
NASA NTRS1982

Aerodynamic characteristics of airfoils with ice accretions

Results of a wind tunnel test to evaluate the performance of an airfoil with simulated rime ice are presented with theoretical comparisons. A NACA 65A413 airfoil was tested in the OSU 6 x 22 inch Transonic Airfoil Wind Tunnel at a Reynolds number near three million and Mach numbers from 0.20 to 0.80. The model was tested in four configurations to determine the aero-dynamic effects of the roughness and shape of a rime ice accretion. The simulated rime ice shape was obtained analytically using a time-stepping dry ice accretion computer code. Lift, drag, moment coefficients, and pressure distributions for the clean and simulated rime ice cases are reported. The measured degradation in airfoil performance is compared to an analytical method which uses existing airfoil analysis computer codes with empirical corrections for the surface roughness. A discussion of the empirical surface roughness correction and uses of other airfoil computer methods is included.

Bragg, M. B.↗
NASA NTRS1983

Numerical simulation of large-scale ocean-atmosphere coupling and the ocean's role in climate

The problem of reducing model generated sigma coordinate data to pressure levels is considered. A mass consistent scheme for performing budget analyses is proposed, wherein variables interpolated to a given pressure level are weighted according to the mass between a nominal pressure level above and either a nominal pressure level below or the Earth's surface, whichever is closer. The method is applied to the atmospheric energy cycle as simulated by the OSU two level atmospheric general circulation model. The results are more realistic than sigma coordinate analyses with respect to eddy decomposition, and are in agreement with the sigma coordinate evaluation of the numerical energy sink. Comparison with less sophisticated budget schemes indicates superiority locally, but not globally.

Gates, W. L.↗
NASA NTRS1982

Use of a multiprocessor for control of a robotic system

In the case of complex industrial operations, the use of a multiprocessor for the control of a robotic system has a number of potential advantages over an employment of a single-processor design. In addition to the increased speed of parallel computation, multiprocessors can provide greater reliability. However, the control of a system with a multiprocessor is much more complicated, and requires resolution of a number of design criteria. The degree of coupling, the processor interconnection configuration, and the method of fault detection and correction are factors in the design of a multiprocessor which need to be considered for each particular application. In connection with the present investigation, a five-unit multiprocessor was built to experiment with the multiprocessor control of a robotic system. While the primary application of the multiprocessor involves the control of the Ohio State University (OSU) Hexapod, an 18-degree-of-freedom, motor-driven walking machine, the multiprocessor was designed to be versatile enough for a numbr of other uses.

Klein, C. A.↗
NASA NTRS1985

Detailed measurements of the flowfield in the vicinity of an airfoil with glaze ice

An experimental study has been conducted in the OSU subsonic tunnel to measure the characteristics of the separation bubble on an airfoil with glaze ice. A measured glaze ice accretion on a NACA 0012 airfoil was simulated in wood for this dry tunnel test. The 21 inch chord model was pressure belted and the ice shape internally tapped to obtain surface pressures, lift and moment coefficients. A wake survey probe was used to obtain airfoil drag. The separation bubble was explored by measuring the time averaged velocities using a split film probe. The probe was positioned using a computer controlled two-dimensional traversing system. In this paper, airfoil lift, drag, and moment coefficient data are compared for the airfoil with and without glaze ice. Velocity profiles in the separation bubble are presented for several chordwise stations at three angles of attack. The ice shape caused a severe lift and drag penalty. The velocity profiles show clearly the large bubble geometry, regions of reversed flow, and bubble reattachment.

Bragg, M. B.↗
NASA NTRS1985

Simulation of the enhanced traffic alert and collision avoidance system (TCAS 2)

The OSU aircraft code is used to analyze and simulate the TCAS 2 circular array which is mounted on the fuselage of a Boeing 737 aircraft. It is shown that the sum and difference patterns radiated by the circular array are distorted by the various structures of the aircraft, i.e., wings, tail, etc. Furthermore, monopulse curves are calculated and plotted for several beam positions and THETA angles. As expected, the worst cases of distortion occur when the beams are pointed toward the tail of the aircraft.

Rojas, R. G.↗
NASA NTRS1986

Seam tracking performance of a Coaxial Weld Vision System and pulsed welding

This report describes a continuation of a series of tests on the Coaxial Weld Vision System at MSFC. The ability of the system to compensate for transients associated with pulsed current welding is analyzed. Using the standard image processing approach for root pass seam tracking, the system is also tested for the ability to track the toe of a previous weld bead, for tracking multiple pass weld joints. This Coaxial Weld Vision System was developed by the Ohio State University (OSU) Center for Welding Research and is a part of the Space Shuttle Main Engine Robotic Welding Development System at MSFC.

Gangl, K. J.↗
NASA NTRS1986

Aerodynamic measurements of an airfoil with simulated glaze ice

An experimental study has been conducted in the OSU subsonic tunnel to measure the detailed aerodynamic characteristics of an airfoil with simulated glaze ice. A special model was built with interchangeable leading edges to be used in this study. One leading edge is that of a NACA 0012, while the other is a simulation of a glaze ice accretion measured in the NACA Lewis Icing Research Tunnel. The model was instrumented with a dense distribution of surface pressure taps to provide excellent detail around the ice shapes and reattachment point. A traversing total pressure probe was used to document the boundary layer characteristics on the NACA 0012 section. The ice shape caused a severe lift and drag penalty, reducing the maximum lift by over 50 percent and causing a 300 percent increase in drag. Surface pressure distributions revealed a large lower surface separation in addition to the expected large upper surface separation.

Bragg, M. B.↗
NASA NTRS1987

Two-dimensional aerodynamic characteristics of the AMES HI-120, HI-8, and LOW-12 airfoils

During the period between June and September 1986, the Aeronautical and Astronautical Engineering Research Laboratory (AARL) at the Ohio State University (OSU) in Columbus, Ohio, conducted tests in the 6"X22" Transonic Blowdown Wind Tunnel to determine the two-dimensional lift, drag, and pitching moment coefficients for three airfoils designated AMES HI-120, AMES LOW-12, and AMES HI-8. These tests covered a Mach number range of 0.20 to 0.86, Reynolds numbers between 2 x 10 to the 6th and 6 x 10 to the 6th powers, and angles of attack between 0 and 13 degs as directed by the NASA Project Engineer; each model was not run at every condition. This work was performed under NASA Grant NAG-2-401, Analysis of Two Advanced Transonic Airfoils.

Gregorek, G. M.↗
NASA NTRS1988

Comparison of pressure distributions on model and full-scale NACA 64-621 airfoils with ailerons for wind turbine application

The aerodynamic similarity between a small (4-inch chord) wind tunnel model and a full-scale wind turbine blade (24-foot tip section with a 36-inch chord) was evaluated by comparing selected pressure distributions around the geometrically similar cross sections. The airfoils were NACA 64-621 sections, including trailing-edge ailerons with a width equal to 38 percent of the airfoil chord. The model airfoil was tested in the OSU 6- by 12-inch High Reynolds Number Wind Tunnel; the full-scale blade section was tested in the NASA Langley Research Center 30- by 60-foot Subsonic Wind Tunnel. The model airfoil contained 61 pressure taps connected by embedded tubes to pressure transducers. A belt containing 29 pressure taps was fixed to the full-scale section at midspan to obtain surface pressure data. Lift coefficients were obtained by integrating pressures, and corrections were made for the 3-D effects of blade twist and downwash in the blade tip section. The results of the two different experimental methods correlated well for angles of attack from minus 4 to 36 degrees and aileron reflections from 0 to 90 degrees.

Gregorek, G. M.↗
NASA NTRS1989

Improved computer simulation of the TCAS 3 circular array mounted on an aircraft

The Traffic advisory and Collision Avoidance System (TCAS) is being developed by the Federal Aviation Administration (FAA) to assist aircraft pilots in mid-air collision avoidance. This report concentrates on the computer simulation of the enchanced TCAS 2 systems mounted on a Boeing 727. First, the moment method is used to obtain an accurate model for the enhanced TCAS 2 antenna array. Then, the OSU Aircraft Code is used to generate theoretical radiation patterns of this model mounted on a simulated Boeing 727 model. Scattering error curves obtained from these patterns can be used to evaluate the performance of this system in determining the angular position of another aircraft with respect to the TCAS-equipped aircraft. Finally, the tracking of another aircraft is simulated when the TCAS-equipped aircraft follows a prescribed escape curve. In short, the computer models developed in this report have generality, completeness and yield reasonable results.

Rojas, R. G.↗
NASA NTRS1989

Effect of simulated glaze ice on a rectangular wing

Experimental measurements of the effect of simulated glaze ice on a three-dimensional wing are presented. A semispan wing of effective aspect ratio five was mounted from a splitter plate in the OSU subsonic wind tunnel. The model has a straight, untwisted rectangular platform, and uses a NACA 0012 airfoil section. Surface pressures were measured at 5 semispan locations and a total-pressure wake-survey probe was used on the model centerline. The section lift and drag data from the model centerline compared well to earlier two-dimensional data. These data show a large drag and maximum lift penalty due to the simulated glaze ice. Three-dimensional span-load data compare well to computational results.

Bragg, M. B.↗
NASA NTRS1990

Measured aerodynamic performance of a swept wing with a simulated ice accretion

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional swept wing is studied experimentally. A semispan wing of effective aspect ratio four was mounted from a splitter plate in the OSU subsonic wind tunnel. The model uses a NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root pieces to allow for 0- and 30-degree sweep. Surface pressures were measured at 5 semispan locations on the swept-wing model. The section lift data for the 5 semispan locations are presented and compared with theory and zero-sweep model results. In addition, previously unpublished roughness data from the zero-sweep model is presented here. These data show a large drag and maximum lift penalty due to rough simulated glaze ice. The effect of wing-sweep is seen through a decrease in wing lift performance for both the clean and iced wing.

Khodadoust, A.↗
NASA NTRS1992

Writing instrument interfaces with xf/tktcl

Tcl is an embedded control language written in C, running primarily under Unix and with an interpreted C look-and-feel. Tk is an X11 toolkit based on tcl. Xf is an application builder for tk. The entire package is public domain and available from sprite.berkeley.edu. This paper discusses the use of tk to develop a user interface for OSIRIS, an infrared camera/spectrograph now operational on the OSU Perkins 1.8m telescope. The good and bad features of the development process are described.

Henden, A. A.↗
NASA NTRS1998

The Development of the Joint NASA GSFC and the National Imagery and Mapping Agency (NIMA) Geopotential Model EGM96

The NASA Goddard Space Flight Center (GSFC), the National Imagery and Mapping Agency (NIMA), and The Ohio State University (OSU) have collaborated to develop an improved spherical harmonic model of the Earth's gravitational potential to degree 360. The new model, Earth Gravitational Model 1996 (EGM96), incorporates improved surface gravity data, altimeter-derived gravity anomalies from ERS-1 and from the GEOSAT Geodetic Mission (GM), extensive satellite tracking data-including new data from Satellite Laser Ranging (SLR), the Global Postioning System (GPS), NASA's Tracking and Data Relay Satellite System (TDRSS), the French DORIS system, and the US Navy TRANET Doppler tracking system-as well as direct altimeter ranges from TOPEX/POSEIDON (T/P), ERS-1, and GEOSAT. The final solution blends a low-degree combination model to degree 70, a block-diagonal solution from degree 71 to 359, and a quadrature solution at degree 360. The model was used to compute geoid undulations accurate to better than one meter (with the exception of areas void of dense and accurate surface gravity data) and realize WGS84 as a true three-dimensional reference system. Additional results from the EGM96 solution include models of the dynamic ocean topography to degree 20 from T/P and ERS-1 together, and GEOSAT separately, and improved orbit determination for Earth-orbiting satellites.

Lemoine, F. G.↗