Search NASA⌕ Search

SEARCH · Search NASA

Results for “Oil flow visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Measurements and Computations of the Turbulent Corner Flow on the NASA Juncture-Flow Model with a Symmetric Wing

The NASA Juncture Flow experiment is designed to acquire high-quality flowfield data deep in the corner of a wing-fuselage junction specifically for the purpose of computational fluid dynamics (CFD) validation and turbulence model improvement. This paper presents and discusses the results of a recent experiment with the juncture-flow model in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The main objective of the test was to expand the existing juncture-flow dataset with a symmetric wing case that displays fully attached, incipient separation, and separated flow in the corner of the wing-fuselage junction, depending on the model angle of incidence. Laser Doppler velocimetry (LDV) measurements were made at three model angles of incidence (0 deg: fully attached, 1 deg: incipient separation, and 5 deg: separated flow) and for each one, mean-flow and Reynolds-stress data were obtained on the fuselage and at several streamwise locations along the corner of the wing-fuselage junction. Supporting measurements were made during the test campaign and included model and tunnel wall static pressures, tunnel wall and ceiling boundary-layer rake data, oil-flow visualizations, and laser-based measurements of the as-built model geometry and model position in the test section. Comparisons between the experimental data on the test article and Reynolds-averaged Navier-Stokes CFD results are presented and discussed.

Juncture Flow↗
NASA NTRS2023

Measurements and Computations of the Turbulent Corner Flow on the NASA Juncture-Flow Model with a Symmetric Wing

The NASA Juncture Flow experiment is designed to acquire high-quality flowfield data deep in the corner of a wing-fuselage junction specifically for the purpose of computational fluid dynamics (CFD) validation and turbulence model improvement. This paper will present and discuss the results of a recent experiment with the juncture-flow model in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The main objective of that test was to expand the existing juncture-flow dataset with a symmetric wing case that displays fully attached, incipient separation, and separated flow in the corner of the wing-fuselage junction, depending on the model pitch angle. Laser Doppler velocimetry (LDV) measurements were made at three model pitch angles (0 deg: fully attached, 1 deg: incipient separation, and 5 deg: separated flow) and for each one, mean-flow and Reynolds-stress data was obtained on the fuselage and at several streamwise locations along the corner of the wing-fuselage junction. Supporting measurements were made during the test campaign and included model and tunnel wall static pressures, tunnel wall and ceiling boundary-layer rake data, oil-flow visualizations, and laser-based measurements of the as-built model geometry and model position in the test section. Comparisons between the experimental data and Reynolds averaged Navier-Stokes CFD results will also be presented and discussed.

Juncture Flow↗
NASA NTRSDate not supplied

Measurements and Computations of the Turbulent Corner Flow on the NASA Juncture-Flow Model with a Symmetric Wing

The NASA Juncture Flow experiment is designed to acquire high-quality flowfield data deep in the corner of a wing-fuselage junction specifically for the purpose of computational fluid dynamics (CFD) validation and turbulence model improvement. This paper will present and discuss the results of a recent experiment with the juncture-flow model in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The main objective of that test was to expand the existing juncture-flow dataset with a symmetric wing case that displays fully attached, incipient separation, and separated flow in the corner of the wing-fuselage junction, depending on the model pitch angle. Laser Doppler velocimetry (LDV) measurements were made at three model pitch angles (0 deg: fully attached, 1 deg: incipient separation, and 5 deg: separated flow) and for each one, mean-flow and Reynolds-stress data was obtained on the fuselage and at several streamwise locations along the corner of the wing-fuselage junction. Supporting measurements were made during the test campaign and included model and tunnel wall static pressures, tunnel wall and ceiling boundary-layer rake data, oil-flow visualizations, and laser-based measurements of the as-built model geometry and model position in the test section. Comparisons between the experimental data and Reynolds averaged Navier-Stokes CFD results will also be presented and discussed.

Juncture Flow↗
NASA NTRS2024

Measurements and Computational Analysis of the Turbulent Corner Flow on the NASA Juncture-Flow Model with a Symmetric Wing

The NASA Juncture Flow Experiment is designed to acquire high-quality flowfield data deep in the corner of a wing-fuselage junction for the purpose of computational fluid dynamics (CFD) validation and turbulence model improvement. This report presents and discusses the results of a recent experiment with the Juncture Flow Model in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The main objective of the test was to expand the existing juncture-flow dataset with a symmetric wing case that displays fully attached, incipient separation, and separated flow in the corner of the wing-fuselage junction, depending on the model angle of incidence. Laser Doppler velocimetry (LDV) measurements were made at three model angles of incidence (0° : fully attached, 1° : incipient separation, and 5° : separated flow) and for each angle, mean-flow and Reynolds-stress data were obtained on the fuselage and at several locations along the corner of the wing-fuselage junction. Supporting measurements were made during the test campaign and include model and tunnel wall static pressures, tunnel wall boundary-layer profiles, oil-flow visualizations, and laser-based measurements of the as-built model geometry and model position in the test section. A companion set of Reynolds-averaged Navier-Stokes (RANS) CFD simulations were also performed and those results were used to support the discussion of the experimental test results.

Juncture Flow↗
NASA NTRS1982

Flow visualization of shock-boundary layer interaction

Two and three-dimensional shock-boundary layer interaction data were obtained from supersonic wind tunnel tests. These interactions are studied both with and without boundary layer bleed. The data verify computational fluid dynamic codes. Surface static pressure, pitot pressure, flow angularity, and bleed rates, are studied by flow visualization techniques. Surface oil flow using fluorescent dye and laser sheet using water droplets as the scattering material are used for flow visualization.

Hingst, W. R.↗
NASA NTRSDate not supplied

A Method for Obtaining Surface Flow Vectors and Its Implementation in Interferometric Skin Friction Measurement

A new method was developed to extract surface flow vectors from an oilflow visualization image that has oil streaklines. The method is analogous to the PIV processing where the image is divided into interrogation windows. A representative flow direction is obtained for each interrogation window using image processing with a line-detection algorithm. Repeating the process for the entire image, one can find the surface vector field. The Hough transformation, Radon transformation and Machine Learning were used as line-detection algorithms. The obtained vector field is then postprocessed to filter spurious vectors and to apply smoothing. The method was tested on 2D and 3D models with different flow complexities. The method was able to predict surface flow vectors for all cases tested. The predicted surface flow vectors were used in obtaining the surface skin friction. The successful implementation of the surface flow vectors enables interferometric skin friction measurements on surfaces beneath 3D complex flows. In addition, the surface flow vectors can be superimposed on the oilflow visualization images to better explain the surface flow topology.

Surface flow vectors↗
NASA NTRSDate not supplied

A Method for Obtaining Surface Flow Vectors and Its Implementation in Interferometric Skin Friction Measurement

A new method was developed to extract surface flow vectors from an oilflow visualization image that has oil streaklines. The method is analogous to the PIV processing where the image is divided into interrogation windows. A representative flow direction is obtained for each interrogation window using image processing with a line-detection algorithm. Repeating the process for the entire image, one can find the surface vector field. The Hough transformation, Radon transformation and Machine Learning were used as line-detection algorithms. The obtained vector field is then postprocessed to filter spurious vectors and to apply smoothing. The method was tested on 2D and 3D models with different flow complexities. The method was able to predict surface flow vectors for all cases tested. The predicted surface flow vectors were used in obtaining the surface skin friction. The successful implementation of the surface flow vectors enables interferometric skin friction measurements on surfaces beneath 3D complex flows. In addition, the surface flow vectors can be superimposed on the oilflow visualization images to better explain the surface flow topology.

Surface flow vectors↗
NASA NTRS1985

Lee-side flow over delta wings at supersonic speeds

An experimental investigation of the lee-side flow on sharp leading-edge delta wings at supersonic speeds has been conducted. Pressure data were obtained at Mach numbers from 1.5 to 2.8, and three types of flow-visualization data (oil-flow, tuft, and vapor-screen) were obtained at Mach numbers from 1.7 to 2.8 for wing leading-edge sweep angles from 52.5 deg to 75 deg. From the flow-visualization data, the lee-side flows were classified into seven distinct types and a chart was developed that defines the flow mechanism as a function of the conditions normal to the wing leading edge, specifically, angle of attack and Mach number. Pressure data obtained experimentally and by a semiempirical prediction method were employed to investigate the effects of angle of attack, leading-edge sweep, and Mach number on vortex strength and vortex position. In general, the predicted and measured values of vortex-induced normal force and vortex position obtained from experimental data have the same trends with angle of attack, Mach number, and leading-edge sweep; however, the vortex-induced normal force is underpredicted by 15 to 30 percent, and the vortex spanwise location is overpredicted by approximately 15 percent.

Miller, D. S.↗
NASA NTRS2015

Global Skin-Friction Measurements Using Particle Image Surface FLow Visualization and a Luminescent Oil-Film

A quantitative global skin-friction measurement technique is proposed. An oil-film is doped with a luminescent molecule and thereby made to fluoresce in order to resolve oil-film thickness, and Particle Image Surface Flow Visualization is used to resolve the velocity field of the surface of the oil-film. Skin-friction is then calculated at location x as (x )xh, where x is the displacement of the surface of the oil-film and is the dynamic viscosity of the oil. The data collection procedure and data analysis procedures are explained, and preliminary experimental skin-friction results for flow over the wing of the CRM are presented.

FISF↗
NASA NTRS2000

Investigation of Flow Separation in a Transonic-fan Linear Cascade Using Visualization Methods

An extensive study into the nature of the separated flows on the suction side of modem transonic fan airfoils at high incidence is described in the paper. Suction surface.flow separation is an important flow characteristic that may significantly contribute to stall flutter in transonic fans. Flutter in axial turbomachines is a highly undesirable and dangerous self-excited mode of blade oscillations that can result in high cycle fatigue blade failure. The study basically focused on two visualization techniques: surface flow visualization using dye oils, and schlieren (and shadowgraph) flow visualization. The following key observations were made during the study. For subsonic inlet flow, the flow on the suction side of the blade is separated over a large portion of the blade, and the separated area increases with increasing inlet Mach number. For the supersonic inlet flow condition, the flow is attached from the leading edge up to the point where a bow shock from the upper neighboring blade hits the blade surface. Low cascade solidity, for the subsonic inlet flow, results in an increased area of separated flow. For supersonic flow conditions, a low solidity results in an improvement in flow over the suction surface. Finally, computational results modeling the transonic cascade flowfield illustrate our ability to simulate these flows numerically.

Lepicovsky, Jan↗
NASA NTRSDate not supplied

Flow Physics Study of Sweeping Jet Actuation on a NACA 0015 Swept Wing Configuration

Preliminary results from a recently completed active flow control (AFC) experiment on a 30 deg swept, semispan wing are presented. The constant chord NACA 0015 wing is configured with sweeping jet actuators at the flap shoulder to study the effects of excitation introduced into a separated, three-dimensional flowfield. The research is aimed at developing efficient active flow control approaches for swept wing configurations. Oil and tuft flow visualization data, steady and unsteady pressure data, particle image velocimetry (PIV), oil flow interferometry (OFI), and force and moment data are used to compare the flowfields with and without AFC. The parameters that were varied include freestream velocity, actuator momentum coefficient, and flap deflection angle.

active flow control↗
NASA NTRS1972

Effects of leading-edge camber on low-speed characteristics of slender delta wings

Wind-tunnel studies have been conducted to determine the effects of leading-edge camber on the low-speed aerodynamic characteristics of a thin, sharp-edge 74 deg delta wing. The results include force and moment measurements, pressure distributions, and flow visualization patterns determined from oil flow, tuft and water vapor observations. The study indicated that leading-edge camber near the apex is effective in controlling the pitch-up tendency of slender delta wings.

Wentz, W. H., Jr.↗
NASA NTRSDate not supplied

A Separation Control CFD Validation Test Case: Baseline and Steady Suction - Part 1

Low speed flow separation over a wall-mounted hump, and its control using steady suction, were studied experimentally in order to generate a data set for a workshop aimed at validating CFD turbulence models. The baseline and controlled data sets comprised static and dynamic surface pressure measurements, flow field measurements using Particle Image Velocimetry (PIV) and wall shear stress obtained via oil-film interferometry. In addition to the specific test cases studied, surface pressures for a wide variety of conditions were reported for different Reynolds numbers and suction rates. Stereoscopic PIV and oil-film flow visualization indicated that the baseline separated flow field was mainly two- dimensional. With the application of control, some three-dimensionality was evident in the spanwise variation of pressure recovery, reattachment location and spanwise pressure fluctuations. Part 2 of this paper, under preparation for the AIAA Meeting in Reno 2005, considers separation control by means of zero-efflux oscillatory blowing.

David Greenblatt↗
NASA NTRS2004

A Separation Control CFD Validation Test Case: Baseline and Steady Suction - Part 1

Low speed flow separation over a wall-mounted hump, and its control using steady suction, were studied experimentally in order to generate a data set for a workshop aimed at validating CFD turbulence models. The baseline and controlled data sets comprised static and dynamic surface pressure measurements, flow field measurements using Particle Image Velocimetry (PIV) and wall shear stress obtained via oil-film interferometry. In addition to the specific test cases studied, surface pressures for a wide variety of conditions were reported for different Reynolds numbers and suction rates. Stereoscopic PIV and oil-film flow visualization indicated that the baseline separated flow field was mainly two-dimensional. With the application of control, some three-dimensionality was evident in the spanwise variation of pressure recovery, reattachment location and spanwise pressure fluctuations. Part 2 of this paper, under preparation for the AIAA Meeting in Reno 2005, considers separation control by means of zero-efflux oscillatory blowing.

Greenblatt, David↗
NASA NTRS1999

Experimental Investigation of Convoluted Contouring for Aircraft Afterbody Drag Reduction

An experimental investigation was performed in the NASA Langley 16-Foot Transonic Tunnel to determine the aerodynamic effects of external convolutions, placed on the boattail of a nonaxisymmetric nozzle for drag reduction. Boattail angles of 15 and 22 were tested with convolutions placed at a forward location upstream of the boattail curvature, at a mid location along the curvature and at a full location that spanned the entire boattail flap. Each of the baseline nozzle afterbodies (no convolutions) had a parabolic, converging contour with a parabolically decreasing corner radius. Data were obtained at several Mach numbers from static conditions to 1.2 for a range of nozzle pressure ratios and angles of attack. An oil paint flow visualization technique was used to qualitatively assess the effect of the convolutions. Results indicate that afterbody drag reduction by convoluted contouring is convolution location, Mach number, boattail angle, and NPR dependent. The forward convolution location was the most effective contouring geometry for drag reduction on the 22 afterbody, but was only effective for M < 0.95. At M = 0.8, drag was reduced 20 and 36 percent at NPRs of 5.4 and 7, respectively, but drag was increased 10 percent for M = 0.95 at NPR = 7. Convoluted contouring along the 15 boattail angle afterbody was not effective at reducing drag because the flow was minimally separated from the baseline afterbody, unlike the massive separation along the 22 boattail angle baseline afterbody.

Deere, Karen A.↗
NASA NTRS1993

An experimental investigation of a Mach 3.0 high-speed civil transport at supersonic speeds

An experimental study was conducted to determine the aerodynamic characteristics of a proposed high speed civil transport. This configuration was designed to cruise at Mach 3.0 and sized to carry 250 passengers for 6500 n.mi. The configuration consists of a highly blended wing body and features a blunt parabolic nose planform, a highly swept inboard wing panel, a moderately swept outboard wing panel, and a curved wingtip. Wind tunnel tests were conducted in the Langley Unitary Plan Wind Tunnel on a 0.0098-scale model. Force, moment, and pressure data were obtained for Mach numbers ranging from 1.6 to 3.6 and at angles of attack ranging from -4 to 10 deg. Extensive flow visualization studies (vapor screen and oil flow) were obtained in the experimental program. Both linear and advanced computational fluid dynamics (CFD) theoretical comparisons are shown to assess the ability to predict forces, moments, and pressures on configurations of this type. In addition, an extrapolation of the wind tunnel data, based on empirical principles, to full-scale conditions is compared with the theoretical aerodynamic predictions.

Hernandez, Gloria↗