Search NASA⌕ Search

SEARCH · Search NASA

Results for “Optical Ceramics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

85 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Proton surface exchange kinetics of perovskite triple conducting thin films for protonic ceramic electrolysis cells: BaPr 0.9 Y 0.1 O 3–δ (BPY) vs. Ba 1–x Co 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3–δ (BCFZY)

Protonic ceramic electrolysis cells (PCECs) are an attractive green H 2 production technology, given their intermediate-temperature operating range and ability to produce dry H 2 . However, PCECs will benefit from development of more efficient and durable “triple conducting” anodes where steam is split, H incorporated, and oxygen evolved. In this work, we evaluated the kinetics of the steam-splitting/H incorporation reaction on BaPr 0.9 Y 0.1 O 3–δ (BPY) in comparison to the benchmark Ba 1–x Co 0.4 Fe 0.4 Z r0.1 Y 0.1 O 3–δ (BCFZY) composition, replacing most of the transition metal elements (Co, Fe, Zr) with the lanthanide Pr. We prepared geometrically well-defined perovskite BPY and BCFZY thin films by pulsed laser deposition and performed simultaneous optical transmission relaxation and electrical conductivity relaxation measurements at 400–500 °C in 0.21 atm O 2 during switching of the steam partial pressure to isolate and compare their proton surface exchange coefficients (k). The k values of BPY were comparable to those of BCFZY and more stable over time. According to angle-resolved XPS and STEM-EDS mapping of FIB cross-sections, the surface of BPY exhibited Ba enrichment, Pr deficiency, and Si contamination. In contrast, BCFZY exhibited Ba deficiency throughout, no obvious surface segregation, and less Si contamination. The Ba segregation on the BPY film appears to have promoted steam splitting/H incorporation kinetics even though the more basic surface reacted with the acidic environmental SiO x H y . Faster kinetics observed on stoichiometric BCFZY vs. Ba-deficient BCFZY confirmed the benefit of a high A-site Ba concentration. This result contrasts with most work on perovskites applied in solid oxide electrolysis cell anodes, in which A-site segregation is considered deleterious for surface reaction kinetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Chemo-Mechanically Driven In Situ Hierarchical Structure Formation in Mixed Conductors (Final Technical Report)

This document is the Final Technical Report for the Early Career project DE-SC0018963. Essential materials for energy technologies tend to exhibit “hierarchical” functions – they perform multiple, inter-related tasks at different locations, across disparate length and time scales. To best support this heterogeneous function, there is a fundamental need to understand and direct formation of corresponding tailored hierarchical architectures. In particular, a wide variety of applications, from energy conversion and storage to sensing and gas separation, rely on oxide mixed ionic and electronic conductors (MIECs). These critical ceramic materials catalyze reactions at their surfaces and selectively transport both ionic and electronic species in the bulk. Ideally, MIECs should adopt hierarchical structures with 1) high surface areas, 2) surface compositions exhibiting high catalytic activity, and 3) microstructural connectivity in the direction needed for fast mass and charge transport. In practice, however, MIECs.

08 HYDROGEN↗
DOE OSTI2026

Boride-based Ceramic Super-high Temperature Thermocouples in Harsh Environments (Final Scientific/Technical Report)

An electromotive force (emf) can be generated along a temperature gradient between the cold end and hot end of a thermoelectric material, termed the Seebeck effect. Based on the Seebeck effect, metallic alloys have been extensively employed to detect temperatures for centuries, named thermocouples. However, commercially available thermocouple alloys suffer from limitations, such as oxidation, chemical degradation, and poor long-term stability under high-temperature harsh environments. This DOE-funded project aimed to develop high-temperature, chemically tolerant thermocouples suitable for operation in extreme environments relevant to semiconducting thermoelectric materials. The research focused on boride-based semiconducting thermoelectric compounds as candidates for next-generation thermocouples with enhanced oxidation resistance, chemical stability, and thermal robustness under conditions representative of charcoal-fired electricity facilities. During the funded years, boride materials were synthesized using an arc-plasma technique under ambient air and argon atmospheres, enabling scalable and cost-effective production compared with conventional boride fabrication methods. The synthesized borides were processed into nanostructured powders, followed by consolidation into dense bulk materials using a spark plasma sintering (SPS) bottom-up approach. Comprehensive characterization was performed, including microstructural analysis, electrical transport measurements, and optical and thermal property evaluation. Both p-type and n-type boride electric legs were fabricated and integrated into boride-based thermocouples. The thermal and irradiation stabilities of the boride nanomaterials and bulk thermoelectric materials were systematically evaluated to assess suitability for long-term operation in harsh environments. Additionally, 12 students were broadly hands-on trained spanning the full research workflow, including word processing and technical editing (e.g., LATEX for manuscript and poster preparation), data collection and analysis (using Python and related libraries and hardware interfaces), sample preparation (including arc-plasma synthesis and spark plasma sintering), and advanced characterization techniques (such as X-ray diffraction, UV–vis spectroscopy, electron microscopy, differential thermal analysis (DTA), and Seebeck coefficient measurements, etc). Overall, this project demonstrated the feasibility of boride-based thermoelectric materials as durable high-temperature thermocouples, providing a promising pathway toward robust temperature sensing technologies aligned with DOE energy infrastructure and extreme-environment monitoring needs.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Hot-pressed ceramic Fe:ZnSe gain-switched laser

We report the first room temperature gain-switched Fe:ZnSe hot-pressed ceramic laser pumped by 2.94 µm radiation of mechanically Q-switched Er:YAG laser. The maximum output energy at 4.2 µm was 41 mJ at 3 Hz repetition rate and 120 ns pulse duration. The measured slope efficiency was 25% with respect to the absorbed energy. This technique could be attractive for the future development of high-energy short-pulse solid-state mid-IR systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Reliability Analysis of Large-Area, Low Pressure-Assisted Silver Sintering for Medium-Voltage Power Modules

Multi-layer insulating ceramic substrates can enable medium-voltage (MV) power modules with reduced peak electric field. This benefit is particularly important for MV silicon carbide (SiC) MOSFETs due to their higher operating voltages. Large-area, low-pressure assisted silver sintering is a potential solution for bonding substrates to create a multi-layer structure. The voiding content and defect density of the bond used to create the multi-layer substrate stack-up is critical to the reliability of the power module and the thermal performance, as this bond is in the primary path for heat dissipation in the power module structure. Here, samples of two-layer direct bonded aluminum (DBA) stacks have been fabricated and subjected to thermal cycling to analyze their reliability. Passive thermal cycling from -40 degrees C to 200 degrees C was performed. Cross-sections were cut at pre-determined intervals and imaged with Scanning Electron Microscopy (SEM). After 1000 thermal cycles, adhesive failures are observed between the sintered silver and the DBA surface. Cross-sections were cut and imaged via optical microscope and SEM. Thermal analyzer measurements are recorded on a 10-kV SiC power module utilizing the sintered DBA substrate stacks.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Thermodynamically Stable, Plasmonic Transition Metal Oxide Nanoparticle Solar Selective Absorbers towards 95% Optical-to-Thermal Conversion Efficiency at 750 °C

Generation 3 (Gen) concentrating solar power (CSP) systems requires a high operation temperature ≥750°C to increase the power-cycle efficiency towards ≥50%. However, such a high operation temperature poses a notable challenge to high temperature materials. On the receiver side, a critical challenge is the lack of solar selective absorbers that demonstrate both high optical-to-thermal energy conversion efficiency η therm approaching 95% and long-term thermal stability at >750°C in air. Existing solar absorbers either have limited η therm ≤89% or deteriorate significantly within 500 h at 750°C; some of these also require costly vacuum deposition for stringent thickness control. Therefore, it is highly desirable to simultaneously achieve η therm ~95% AND high thermal stability at 750°C for future generations of CSP receivers. This project has investigated and developed low-cost, highly scalable spray-coated transition metal oxide nanoparticle (NP) pigmented solar selective coatings on various types of Inconel alloy tube sections that are thermodynamically stable at 750-800°C in air, maintaining η therm >94.3%(93.2%) under a solar concentration ratio of C=1000 after 60 simulated day-night cycles at 750ºC (800ºC) (1 cycle=12 h at 750 or 800°C and 12h ramping down to 25°C). We have also coated up to 48 inches long receiver tubes for preliminary solar testing under Norwich Technology’s parabolic trough systems, demonstrating notably improved performance in solar heating compared to benchmark Pyromark 2500 coatings. Two key innovations have been developed in this project: (1) We achieved an unprecedented high thermal efficiency >94% by optimizing the d-band optical absorption spectra of transition metal ions, engineering their valences and stoichiometry; (2) We were able to maintain or even slightly increase the efficiency when operating at 750°C in air by engineering the interdiffusion of transition metal ions between the coating and the Inconel substrate to our advantage. Featuring high-temperature solar spectral selectivity and thermodynamic stability in air, as well as low-cost, highly scalable solution-chemical synthesis and spray coating techniques, this innovation in solar selective absorber technology alone accounts for nearly 40% of the targeted reduction in the levelized cost of electricity (LCOE) from the receiver, thermal energy storage, and operation & maintenance combined by 2030, as proposed by the U.S. Department of Energy. For a 110 MWe CSP power plant, this LCOE reduction from the solar selective coating alone transfers to ~$\$ $1.9 M increase in annual profit based on a sales price of 10¢/kWh (or an annual sale of $50 M/year). The high solar absorptance (~98%) NP pigment materials developed in this project are equally applicable to volumetric receivers either as a coating or as bigger ceramic microspheres after sintering, potentially benefiting Gen3 falling particle CSP technologies. All these contributions facilitate the larger scale deployment of CSP systems with energy storage capability to address the intermittency issue of solar energy towards dispatchable solar electricity, bridging the temporal gap between peak solar electricity production and peak electricity consumption. The collaboration with Norwich Technologies and Brayton Energy in this project will also facilitate the future commercialization of this new solar selective coating technology developed in this SIPS project.

14 SOLAR ENERGY↗
DOE OSTI2024

Development and Application of In Situ Nanocharacterization to Photocatalytic Materials for Solar Fuel Generation

Photocatalytic materials offer an attractive approach for converting solar energy into chemical energy but the performance of the current generation of materials is insufficient to make a technology viable. To address this deficiency, it is necessary to develop a fundamental atomic level understanding of the functioning of such materials so that strategies can be developed to improve performance. This project was undertaken to explore the fundamental structure and properties of photocatalytic materials using atomic resolution imaging and spectroscopy techniques available on advanced transmission electron microscopy. Specifically, there is a need to develop an understanding of how atomic structures/defects and nanoparticle configurations regulate electronic, optical, and catalytic properties to facilitate the design of next generation photocatalysts for solar fuel production. The work focused on fundamental materials information that can be gained from advanced transmission electron microscopy study on novel and existing photocatalytic systems with an emphasis on the hydrogen evolution reaction (HER). Throughout the project, new instrumentation and microscopy characterization tools were developed. Two focus areas were: developing in situ TEM methods and advanced electron energy-loss spectroscopic for nanoscale analysis of catalysts. The work spanned a period of 12 years and for convenience, the report is divided into four phases, approximately corresponding to the four funding periods of the program. Most of the significant results are reported in archival journal publications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Performance of Embedded Sensors in 3D Printed SiC

This report summarizes recent advances in embedding sensors in 3D printed silicon carbide (SiC) ceramic components under the Transformational Challenge Reactor (TCR) program. The additive manufacturing technologies developed under this program will enable fabrication of complex structures with embedded fuels and sensors. The sensors will be capable of characterizing fuel performance using spatially distributed measurements at the most strategic locations that would be otherwise inaccessible using conventional manufacturing techniques. While previous programmatic updates describe initial concepts for embedding sensors, materials selection, and initial characterization of the embedded sensors, the technology requires further demonstration, and quality-significant procedures must be established before the embedding technology is ready for adoption by industry. To this end, this report describes the most effective techniques that have been used to embed functional sensors in 3D printed components using a combination of binder-jet additive manufacturing and chemical vapor infiltration (CVI). A detailed procedure describes each step in the process and is available upon request. Molybdenum (Mo)-sheathed thermocouples have been successfully embedded in complex SiC components, and temperatures were monitored in situ during the embedding process. Post-embedding measurements showed no significant hysteresis, and characterization of the interface revealed qualitatively strong bonding around the entire perimeter of the sensor sheath. Distributed fiber-optic temperature sensors were able to briefly measure temperature profiles during CVI, but they ultimately failed prior to completion of the CVI run. The failure appears to be related to the fiber coating at temperatures close to 1,000°C. Future work will focus on irradiation testing of embedded thermocouples and other sheathed electrical sensors, as well as the identification of fiber-optic sensor coatings that can survive CVI.

42 ENGINEERING↗
DOE OSTI2020

Coupling between interfacial charge and mechanical deformation at high temperatures in ceramics. Final report

Basic research, under this project, has led to new fundamental discoveries in the effect of electric field (and temperature) on diffusion kinetics, electroluminescence and electronic conductivity in ceramic materials. For example, yttria stabilized zirconia sinters in just seconds well below 1000°C, while, at the same time, exhibiting a highly non-linear rise in conductivity, and intense electroluminescence. The phenomenon has been shown to occur in nearly all ceramics whether they are ionic or electronic conductors, or insulators. The rise in conductivity leads to Joule heating but in-situ measurements with a platinum standard at APS and Brookhaven (NSLS-II) have shown that the temperatures are much below what would have been needed to sinter in a few seconds. We have explored the hypothesis that huge concentrations of Frenkel pairs of vacancies and interstitials are produced. While these point defects accelerate sintering (by the interstitials being transported to the pores and the vacancies to the grain boundaries), they may also produce electron-hole pairs which can impart high electrical conductivity or recombine to emit photons. Many measurements, including in-situ measurements of lattice expansion are consistent with this hypothesis. However, the energy barrier for generating Frenkels in zirconia for example is much larger than can be expected at temperature and electrical fields in these experiments. Most recent work suggests that short wavelength phonons play a critical role in the genesis of the “flash” phenomenon. For example, the Debye temperature has been shown to be the lower bound for initiating flash. Molecular dynamics simulations have shown that large concentrations of Frenkel pairs can form under the proliferation of “optical” phonons at the edge of the Brillouin zone, that is with a wavelength at or below the lattice parameter. This project has led to the development of new experimental techniques as well as a software hardware interface for process and control and data analysis in real time, with a time scale of less than one second. This approach spells a new paradigm in materials science research. It potential impact on high rate manufacturing is self evident.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Utilization of Novel (KNbO 3 ) 1− x (Ba 2 FeNbO 6 ) x ( x = 0.1, 0.2, 0.3) Solid Solutions for Efficient Photo‐Assisted Fenton Degradation of Methylene Blue Dye

Novel (KNbO 3 ) 1− x (Ba 2 FeNbO 6 ) x ( x = 0.1, 0.2, 0.3) solid solutions corresponding to K 0.82 Ba 0.18 Fe 0.09 Nb 0.91 O 3 , K 0.64 Ba 0.36 Fe 0.18 Nb 0.82 O 3 , and K 0.46 Ba 0.54 Fe 0.27 Nb 0.73 O 3 compounds have been synthesized via molten salt method. X‐ray diffraction confirms the formation of solid solutions, while transmission electron microscopy combined with energy‐dispersive spectroscopy results demonstrates a homogeneous distribution of elements. The obtained solid solutions crystallized in a cubic crystal structure, whereas the parent KNbO 3 possesses an orthorhombic structure. The wide bandgap semiconductor KNbO 3 transformed into a visible‐light‐active material, with its bandgap energy reduced from 3.56 eV to ≈2.4 eV. The substitution of K in KNbO 3 with Ba is responsible for structural modification from orthorhombic to cubic symmetry, whereas both structural modification and the substitution of Nb with Fe correlated with optical properties. The photocatalytic activities of all obtained solid solutions are improved compared with the parent KNbO 3 and Ba 2 FeNbO 6 compounds for photocatalytic degradation of methylene blue (MB) dye. Among the series of solid solutions, K 0.82 Ba 0.18 Fe 0.09 Nb 0.91 O 3 photocatalysts show the highest MB removal efficiency owing to its relatively higher surface area, suppressed charge carrier recombination, and more negative conduction band edge. Moreover, K 0.82 Ba 0.18 Fe 0.09 Nb 0.91 O 3 photocatalyst (0.1 g) combined with hydrogen peroxide (H 2 O 2 ) to form a novel photo‐Fenton system, achieving almost complete degradation of 100 mL of 10 mg L −1 MB dye in 30 min.

Avcıoğlu, Celal [Technische Universität Berlin, Fa↗
DOE OSTI2020

Experimental system for studying temperature gradient-driven fracture of oxide nuclear fuel out of reactor

Temperature gradients in ceramic light water reactor (LWR) uranium dioxide (UO 2 ) nuclear fuel pellets generate thermal stresses that cause fractures in the fuel beginning early in the life of fresh fuel. The combination of heating due to fission and forced convective cooling on the exterior of LWR fuel rods generates a temperature profile that is difficult to replicate outside the reactor environment. In the present study, a state-of-the-art experimental set-up using electrical heating to replicate fission heating was built and surrogate fuel materials such as ceria (CeO 2 ) were used to validate the system. Cracking experiments were conducted on these surrogates by inducing reactivity-initiated-accident (RIA) like temperature gradients in the pellets via induction and direct resistance heating. Induction heating was done using copper coils and molybdenum susceptors which heated the surrogates to a threshold temperature that is sufficiently high for the fuel material to conduct current. Thereafter, direct resistance heating was used by a D.C. power supply to introduce volumetric heating to replicate LWR operating conditions analogous to fission heating. The pellets were held against nickel electrodes and mounted on a boron nitride test-stand. All the tests were carried out in a stainless-steel vacuum chamber. Simultaneous real-time dual imaging of the surrogate pellet surface has been implemented using an optical and infrared camera system which will be mounted along axial and perpendicular directions to the pellet surface respectively. A beam-splitter was used to split the incoming radiation from the sample into two halves. While one of the beams is transmitted from the splitter through a bandpass filter to obtain optical images, the other beam is reflected from the splitter to the thermal camera to capture full field temperature gradients of the as fabricated pellet surface during crack initiation and propagation. In the current series of tests, a 2-color pyrometer was used for recording and comparing the surface and centerline temperatures of the surrogate pellets in lieu of the thermal camera. A LabVIEW data acquisition system has been set up for collecting useful data during experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Structural Origins of High MoO 3 Solubility in Peraluminous Borosilicate Glasses

Molybdenum (Mo) imposes strict loading limits in conventional borosilicate nuclear waste glasses due to the tendency of tetrahedral molybdate [MoO 4 ] 2− species to phase-separate and crystallize as alkali molybdates. Here, we demonstrate an unprecedented 13.96 wt % (7.51 mol %) MoO 3 solubility in peraluminous sodium aluminoborosilicate glasses a ∼15× increase over their peralkaline counterparts. Using Raman spectroscopy, multinuclear and dipolarcorrelation magic angle spinning nuclear magnetic resonance (MAS NMR), electron paramagnetic resonance (EPR), and scanning transmission electron microscopy (STEM)-energy dispersive spectroscopy (EDS), we reveal that Nadeficient, low optical basicity conditions stabilize octahedral MoO 6 units, which polymerize into molybdite-like Mo−O clusters dispersed within the glass matrix. These Mo-rich clusters suppress the formation of depolymerized [MoO 4 ] 2− environments typically responsible for Na 2 MoO 4 precipitation and instead promote the formation of Na 2 Mo 2 O 7 as the saturation phase. Concurrently, Mo solubility drives the conversion of AlO 4 − to higher-coordination AlO 5 species, liberating Na + that is subsequently sequestered in molybdate-rich domains. The combined evolution of Mo coordination, modifier redistribution, and network depolymerization provides a mechanistic basis for the markedly enhanced Mo solubility in peraluminous compositions. These findings establish new structural guidelines for designing aluminoborosilicate waste forms with substantially greater capacity to incorporate Mo-rich nuclear waste streams.

Amorphous materials↗
DOE OSTI2024

Strain phase equilibria and phase‐field method of ferroelectric polydomain: A case study of monoclinic K x Na 1 − x NbO 3 thin films

Abstract Knowledge of the thermodynamic equilibria and domain structures of ferroelectrics is critical to establishing their structure–property relationships that underpin their applications from piezoelectric devices to nonlinear optics. Here, we establish the strain condition for strain phase separation and polydomain formation and analytically predict the corresponding domain volume fractions and wall orientations of, relatively low symmetry and theoretically more challenging, monoclinic ferroelectric thin films by integrating thermodynamics of ferroelectrics, strain phase equilibria theory, microelasticity, and phase‐field method. Using monoclinic K x Na 1 − x NbO 3 (0.5 < x < 1.0) thin films as a model system, we establish the polydomain strain–strain phase diagrams, from which we identify two types of monoclinic polydomain structures. The analytically predicted strain conditions of formation, domain volume fractions, and domain wall orientations for the two polydomain structures are consistent with phase‐field simulations and in good agreement with experimental results in the literature. The present study demonstrates a general, powerful analytical theoretical framework to predict the strain phase equilibria and domain wall orientations of polydomain structures applicable to both high‐ and low‐symmetry ferroelectrics and provide fundamental insights into the equilibrium domain structures of ferroelectric K x Na 1 − x NbO 3 thin films that are of technology relevance for lead‐free dielectric and piezoelectric applications.

36 MATERIALS SCIENCE↗