Search NASA⌕ Search

SEARCH · Search NASA

Results for “PROPELLERS - DESIGN VARIABLES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

A Monte Carlo investigation of thrust imbalance of solid rocket motor pairs

A technique is described for theoretical, statistical evaluation of the thrust imbalance of pairs of solid-propellant rocket motors (SRMs) firing in parallel. Sets of the significant variables, determined as a part of the research, are selected using a random sampling technique and the imbalance calculated for a large number of motor pairs. The performance model is upgraded to include the effects of statistical variations in the ovality and alignment of the motor case and mandrel. Effects of cross-correlations of variables are minimized by selecting for the most part completely independent input variables, over forty in number. The imbalance is evaluated in terms of six time - varying parameters as well as eleven single valued ones which themselves are subject to statistical analysis. A sample study of the thrust imbalance of 50 pairs of 146 in. dia. SRMs of the type to be used on the space shuttle is presented. The FORTRAN IV computer program of the analysis and complete instructions for its use are included. Performance computation time for one pair of SRMs is approximately 35 seconds on the IBM 370/155 using the FORTRAN H compiler.

Sforzini, R. H.↗
NASA NTRS1926

Some aspects of the comparison of model and full-scale tests

This paper was delivered before the Royal Aeronautical Society as the 1925 Wilbur Wright Memorial lecture. It treats the subject of scale effect from the standpoint of the engineer rather than the physicist, in that it shows what compromises are necessary to secure satisfactory engineering model test data and how these test data compare with full scale or with theoretical values. The paper consists essentially of three parts: (1) a brief exposition of the theory of dynamic similarity, (2) application of the theory to airplane model tests, illustrated by test data on airfoils from the National Advisory Committee for Aeronautics variable-density wind tunnel, and (3) application of the theory to propeller testing, illustrated by comparisons of model and full-scale results.

Taylor, D W↗
NASA NTRS1977

Impact absorbing blade mounts for variable pitch blades

A variable pitch blade and blade mount are reported that are suitable for propellers, fans and the like and which have improved impact resistance. Composite fan blades and blade mounting arrangements permit the blades to pivot relative to a turbine hub about an axis generally parallel to the centerline of the engine upon impact of a large foreign object, such as a bird. Centrifugal force recovery becomes the principal energy absorbing mechanism and a blade having improved impact strength is obtained.

Ravenhall, R.↗
NASA NTRS1980

Aeropropulsion in year 2000

A sampling of probable future engine types, such as convertible engines for helicopters, turboprops for fuel-conservative airliners, and variable-cycle engines for supersonic transports are presented. Related technology improvements in propellers, materials, noise suppression, etc. are reviewed.

Weber, R. J.↗
NASA NTRS1982

Investigation of a panel code for airframe/propeller integration analyses

The Hess panel code was investigated as a procedure to predict the aerodynamic loading associated with propeller slipstream interference on the airframe. The slipstream was modeled as a variable onset flow to the lifting and nonlifting bodies treated by the code. Four sets of experimental data were used for comparisons with the code. The results indicate that the Hess code, in its present form, will give valid solutions for nonuniform onset flows which vary in direction only. The code presently gives incorrect solutions for flows with variations in velocity. Modifications to the code to correct this are discussed.

Miley, S. J.↗
DOE OSTI2023

Swelling and permeability effects during propellant cookoff

Large rocket motors may violently explode when exposed to accidental fires. Even hot metal fragments from a nearby accident may penetrate the propellant and ultimately cause thermal ignition. A mechanistic understanding of heated propellants leading to thermal runaway is a major unsolved problem. Here we show that thermal ignition in propellants can be predicted using a universal cookoff model coupled to a micromechanics pressurization model. Our model predicts the time to thermal ignition in cookoff experiments with variable headspace volumes. Furthermore, we found that experiments with headspace volumes are more prone to deformation which distorts pores and causes increased permeability when the propellant expands into this headspace. Delayed ignition with larger headspace volume correlates with lower headspace pressures during decomposition. We found that our predictions matched experimental measurements best when the initial propellant was impermeable to gas flow rather than being permeable. Similar behavior is expected with other energetic materials with rubbery binders. Our model is validated using data from a separate laboratory. We also present an uncertainty analysis using Latin Hypercube Sampling (LHS) of thermal ignition caused by a steel fragment embedded in the propellant.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1993

Space Shuttle Main Engine real time stability analysis

The Space Shuttle Main Engine (SSME) is a reusable, high performance, liquid rocket engine with variable thrust. The engine control system continuously monitors the engine parameters and issues propellant valve control signals in accordance with the thrust and mixture ratio commands. A real time engine simulation lab was installed at MSFC to verify flight software and to perform engine dynamic analysis. A real time engine model was developed on the AD100 computer system. This model provides sufficient fidelity on the dynamics of major engine components and yet simplified enough to be executed in real time. The hardware-in-the-loop type simulation and analysis becomes necessary as NASA is continuously improving the SSME technology, some with significant changes in the dynamics of the engine. The many issues of interfaces between new components and the engine can be better understood and be resolved prior to the firing of the engine. In this paper, the SSME real time simulation Lab at the MSFC, the SSME real time model, SSME engine and control system stability analysis, both in real time and non-real time is presented.

Kuo, F. Y.↗
NASA NTRS1993

Computational analysis of Variable Thrust Engine (VTE) performance

The Variable Thrust Engine (VTE) of the Orbital Maneuvering Vehicle (OMV) uses a hypergolic propellant combination of Monomethyl Hydrazine (MMH) and Nitrogen Tetroxide (NTO) as fuel and oxidizer, respectively. The performance of the VTE depends on a number of complex interacting phenomena such as atomization, spray dynamics, vaporization, turbulent mixing, convective/radiative heat transfer, and hypergolic combustion. This study involved the development of a comprehensive numerical methodology to facilitate detailed analysis of the VTE. An existing Computational Fluid Dynamics (CFD) code was extensively modified to include the following models: a two-liquid, two-phase Eulerian-Lagrangian spray model; a chemical equilibrium model; and a discrete ordinate radiation heat transfer model. The modified code was used to conduct a series of simulations to assess the effects of various physical phenomena and boundary conditions on the VTE performance. The details of the models and the results of the simulations are presented.

Giridharan, M. G.↗
NASA NTRS1993

Propeller blade retention system

The invention concerns the mounting of propeller blades to a ring-shaped rotor. The blades are of the variable pitch type, and the shank of each blade extends through a respective hole in the rotor. Each hole contains an annular shelf which is fastened to the wall of the hole and surrounds each shank. Each shank bears a pair of bearing races which sandwich the annular shelf in order to connect the blade to the rotor. Bearing rollers are positioned between the annular shelf and the bearing races.

Elston, III, Sidney B.↗
NASA NTRS2004

Orbit Optimization For The Geospace Electrodynamics Connections (GEC) Mission

Part of NASA's Solar Terrestrial Probe line of missions, the Geospace Electrodynamics Connections (GEC) mission will deploy a formation of three spacecraft to perform in-situ atmospheric research in the low Ionosphere-Thermosphere region. These spacecraft will fly together in a %tring-of-pearls formation with variable spacings ranging from 10 seconds to one-quarter of an orbit at perigee. Over the course of its two-year mission, the three spacecraft will perform ten, 1-week dipping campaigns whereby they maneuver to lower their perigee to near 134 km. Using available launch vehicle performance data, an optimal parking orbit of 222 x 1525 km was found to maximize the dry mass available while providing enough propellant to perform the ten deep-dipping campaigns over its two-year mission. The results were used to create multi-variable contour plots containing the orbit perigee, the orbit apogee, spacecraft dry mass, propellant mass, and T500 (a science data collection figure of merit that tabulates the cumulative time spent below 500 km). These plots illustrate how the mission can trade off science return relative to the cost in dry mass and propellant. Other optimal solutions such as minimum propellant or maximum T500 were found to either limit the science data collection or to be dry mass limiting, respectively. Sensitivity analyses were performed to find new optimal (maximum dry mass) solutions if the number of campaigns changed, if the coefficient of drag (CD) were different, and if the propellant specific impulse were increased. A surprising result showed that the dry mass and T500 were both increased if the number of campaigns decreased. Changes in CD provided the expected results - raising CD lowered both the dry mass and T500 while lowering CD raised both the dry mass and T500. Increases in the propellant specific impulse had the expected outcome of raising the dry mass and lowering the propellant load but there was no change in the T500 figure of merit. The orbit optimization was performed parametrically using a Matlab(TradeMark) script and validated using FreeFlyer(TradeMark), a commercial orbit analysis tool. ,

Mesarch, Michael A.↗
NASA NTRS1988

High variable mixture ratio oxygen/hydrogen engine

The ability of an O2/H2 engine to operate over a range of high-propellant mixture ratios was previously shown to be advantageous in single stage to orbit (SSTO) vehicles. The results are presented for the analysis of high-performance engine power cycles operating over propellant mixture ratio ranges of 12 to 6 and 9 to 6. A requirement to throttle up to 60 percent of nominal thrust was superimposed as a typical throttle range to limit vehicle acceleration as propellant is expended. The object of the analysis was to determine areas of concern relative to component and engine operability or potential hazards resulting from the operating requirements and ranges of conditions that derive from the overall engine requirements. The SSTO mission necessitates a high-performance, lightweight engine. Therefore, staged combustion power cycles employing either dual fuel-rich preburners or dual mixed (fuel-rich and oxygen-rich) preburners were examined. Engine mass flow and power balances were made and major component operating ranges were defined. Component size and arrangement were determined through engine layouts for one of the configurations evaluated. Each component is being examined to determine if there are areas of concern with respect to component efficiency, operability, reliability, or hazard. The effects of reducing the maximum chamber pressure were investigated for one of the cycles.

Erickson, C. M.↗
NASA NTRS2019

Converging-Diverging Nozzle Thruster Code for Nuclear or Chemical Rocket Performance Computations

This report describes development of a variable area ratio C-D nozzle numerical computational code "THRST", applicable to the evaluation of nuclear or chemical rocket performance. The propellant for the nuclear rockets is para-hydrogen with gas properties supplied by a sub-routine, while properties for chemical thrusters need to be user input. Detailed documentation of input and output variables and sample output listings enable the report to function as a "User Manual".

Juhasz, Albert J.↗
NASA NTRS1996

Augmentation of Rocket Propulsion: Physical Limits

Rocket propulsion is not ideal when the propellant is not ejected at a unique velocity in an inertial frame. An ideal velocity distribution requires that the exhaust velocity vary linearly with the velocity of the vehicle in an inertial frame. It also requires that the velocity distribution variance as a thermodynamic quantity be minimized. A rocket vehicle with an inert propellant is not optimal, because it does not take advantage of the propellant mass for energy storage. Nor is it logical to provide another energy storage device in order to realize variable exhaust velocity, because it would have to be partly unfilled at the beginning of the mission. Performance is enhanced by pushing on the surrounding because it increases the reaction mass and decreases the reaction jet velocity. This decreases the fraction of the energy taken away by the propellant and increases the share taken by the payload. For an optimal model with the propellant used as fuel, the augmentation realized by pushing on air is greatest for vehicles with a low initial/final mass ratio. For a typical vehicle in the Earth's atmosphere, the augmentation is seen mainly at altitudes below about 80 km. When drag is taken into account, there is a well-defined optimum size for the air intake. Pushing on air has the potential to increase the performance of rockets which pass through the atmosphere. This is apart from benefits derived from "air breathing", or using the oxygen in the atmosphere to reduce the mass of an on-board oxidizer. Because of the potential of these measures, it is vital to model these effects more carefully and explore technology that may realize their advantages.

Taylor, Charles R.↗
NASA NTRS2002

A Plasma Rocket Demonstration on the International Space Station

The Advanced Space Propulsion Laboratory at the NASA Johnson Space Center has been engaged in the development of a magneto-plasma rocket for several years. This type of rocket could be used in the future to propel interplanetary spacecraft. One feature of this concept is the ability to vary its specific impulse so that it can be operated in a mode that maximizes propellant efficiency or a mode that maximizes thrust. For this reason the system is called the Variable Specific Impulse Magneto-plasma Rocket or VASIMR. This ability to vary specific impulse and thrust will allow for optimum low thrust interplanetary trajectories and results in shorter trip times than is possible with fixed specific impulse systems while preserving adequate payload margins. In the development of the VASIMR technology, a series of ground-based experiments and space demonstrations are envisioned. A ground-based experiment of a low-power VASIMR prototype rocket is currently underway at the Advanced Space Propulsion Laboratory. The next step is a proposal to build and fly a 25-kilowatt VASIMR rocket as an external payload on the International Space Station. This experiment will provide an opportunity to demonstrate the performance of the rocket in space and measure the induced environment. The experiment will also utilize the space station for its intended purpose as a laboratory with vacuum conditions that cannot be matched by any laboratory on Earth. The VASIMR experiment will also blaze the trail for the wider application of advanced electric propulsion on the space station. An electric propulsion system like VASIMR, if provided with sufficient electrical power, could provide continuous drag force compensation for the space station. Drag compensation would eliminate the need for reboosting the station, an operation that will consume about 60 metric tons of propellant in a ten-year period. In contrast, an electric propulsion system would require very little propellant. In fact, a system like VASIMR can use waste hydrogen from the station's life support system as its propellant. This waste hydrogen is otherwise dumped overboard. Continuous drag compensation would also improve the microgravity conditions on the station. So electric propulsion can reduce propellant delivery requirements and thereby increase available payload capacity and at the same time improve the conditions for scientific research.

Petro, Andrew J.↗
NASA NTRS1985

Flight vehicle propellant surface motion by numerical method

The marker and cell technique is applied to three idealized hydrodynamic situations of interest to the Space Shuttle External Tank (ET). These applications illustrate the versatility of this technique as well as its usefulness in solving similar problems in the aerospace industry. The codes used are the simplified marker and cell (SMAC) code and the variable grid simplified marker and cell code named ERIE. The examples focus on the dropout height in the LH2 tank, the slosh behavior of propellant in the bottom dome of the ET during thrust termination, both of which are required to accurately determine the amount of usable propellants, and the effect on liquid surface due to LO2 tank wall motions occurring during Space Shuttle lift-off. Comparisons with experimental results and linear theory are also presented.

Mehta, G.↗
NASA NTRS1981

User's manual for a computer program to calculate discrete frequency noise of conventional and advanced propellers

A user's manual is presented for a computer program for the calculation of discrete frequency noise of conventional and advanced propellers. The structure of the program and the subroutines describing the input functions are discussed. Input variables and their default values and the variables in the output data sheet are defined. Two versions of the program are available. These differ only in the graphic output capability. One version has only printed output capability. A second version with extensive graphic output capability is available for the computer system at Langley. This Manual includes four detailed examples of both the printed and graphic outputs. These examples may be reproduced by users to check their code on their computer system.

Martin, R. M.↗
NASA NTRS2012

NASA Tech Briefs, February 2012

This issue contains the following briefs: (1) Optical Comb from a Whispering Gallery Mode Resonator for Spectroscopy and Astronomy Instruments Calibration (2) Real-Time Flight Envelope Monitoring System (3) Nemesis Autonomous Test System (4) Mirror Metrology Using Nano-Probe Supports (5) Automated Lab-on-a-Chip Electrophoresis System (6) Techniques for Down-Sampling a Measured Surface Height Map for Model Validation (7) Multi-Component, Multi-Point Interferometric Rayleigh/Mie Doppler Velocimeter (8) Frequency to Voltage Converter Analog Front-End Prototype (9) Dust-Tolerant Intelligent Electrical Connection System (10) Gigabit Ethernet Asynchronous Clock Compensation FIFO (11) High-Speed, Multi-Channel Serial ADC LVDS Interface for Xilinx Virtex-5 FPGA (12) Glovebox for GeoLab Subsystem in HDU1-PEM (13) Modified Process Reduces Porosity when Soldering in Reduced Gravity Environments (14) Use of Functionalized Carbon Nanotubes for Covalent Attachment of Nanotubes to Silicon (15) Flexible Plug Repair for Shuttle Wing Leading Edge (16) Three Dimensionally Interlinked, Dense, Solid Form of Single-Walled CNT Ropes (17) Axel Robotic Platform for Crater and Extreme Terrain Exploration (18) Site Tamper and Material Plow Tool - STAMP (19) Magnetic Interface for Segmented Mirror Assembly (20) Transpiration-Cooled Spacecraft-Insulation-Repair Fasteners (21) Fluorescence-Based Sensor for Monitoring Activation of Lunar Dust (22) Aperture Ion Source (23) Virtual Ultrasound Guidance for Inexperienced Operators (24) Model-Based Fault Diagnosis: Performing Root Cause and Impact Analyses in Real Time (25) Interactive Schematic Integration Within the Propellant System Modeling Environment (26) Magnetic and Electric Field Polarizations of Oblique Magnetospheric Chorus Waves (27) Variable Sampling Mapping.

Source record↗