Search NASA⌕ Search

SEARCH · Search NASA

Results for “PVC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Studies on the Module Structure for the NOvA Liquid Scintillator Neutrino Detector

This thesis contains studies pertinent to the construction of modules for the NOνAexperiment detectors. The tensile strength of acrylic and epoxy adhesives used in construction of the detector was studied over time and with various surface preparations. Sanding and corona discharge surface treatments increased the bond strength of the acrylic by 10-20%; aging in oil did not affect the acrylic bond strength while aging in air at 50°C for 9 months (equivalent to approximately 5 years at room temperature) increased the acrylic bond strength by 25%. For the epoxy, corona discharge treated samples’ strength increased slightly after aging while the strength of sanded samples in air remained consistent and sanded samples in oil decreased by 17% when aged at 50°C for 1.5 years (equivalent to approximately 10 years at room temperature).All materials used in the detector were studied to determine if degrading interaction would occur with the pseudocumene liquid scintillator. Substances such as acrylic adhesive and PTFE paste were found to interact with the scintillator while materials such as a variety of PVCs, epoxy adhesives, and PTFE tape were found to be non-reactive with the scintillator. Following the appearance of cracks on manifold covers in installed modules, studies were carried out to help to determine the cause and mitigation of these cracks. Manifold covers that had been pressure tested at various pressures during the check of the seals during the manufacturing process were examined for the formation of cracks. “Containment units” were used to constrain the swelling of the manifold covers during pressure testing. Internal cracks were visible on the majority of manifold covers tested at 1.4 bar with the original containment units. It was found that reducing the pressure testing of the modules from 1.4 bar to 0.7 bar and increasing the rigidity of the pressure test containment units eliminated the formation of visible cracks in the manifold covers. Stress concentration in small fillet radius injection molded PVC was studied. GeonM3500 PVC has a yield strength 12% greater than Geon M3800 PVC originally used for the manifold covers but increased the stress concentrated failure time by 6600% and was thus chosen to mold new manifold covers after a redesign to eliminate stress concentrating features.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Female Pelvic Vein Embolization: Indications, Techniques, and Outcomes

Until recently, the main indication for pelvic vein embolization (PVE) in women was to treat pelvic venous congestion syndrome (PVC) but increasingly, patients with refluxing pelvic veins associated with leg varicosities are also being treated. A more unusual reason for PVE is to treat pelvic venous malformations, although such lesions may be treated with sclerotherapy alone. Embolotherapy for treating PVC has been performed for many years with several published studies included in this review, whilst an emerging indication for PVE is to treat lower limb varicosities associated with pelvic vein reflux. Neither group, however, has been subjected to an adequate randomized, controlled trial. Consequently, some of the information presented in this review should be considered anecdotal (level III evidence) at this stage, and a satisfactory ‘proof’ of clinical efficacy remains deficient until higher-level evidence is presented. Furthermore, a wide range of techniques not accepted by all are used, and some standardization will be required based on future mandatory prospective studies. Large studies have also clearly shown an unacceptably high recurrence rate of leg varicose veins following venous surgery. Furthermore, minimally or non-invasive imaging is now revealing that there is a refluxing pelvic venous source in a significant percentage of women with de novo leg varicose veins, and many more with recurrent varicosities. Considering that just over half the world’s population is female and a significant number of women not only have pelvic venous reflux, but also have associated leg varicosities, minimally invasive treatment of pelvic venous incompetence will become a common procedure.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

An Investigation on Magnetic-Interacting Fe{sub 3}O{sub 4} Nanoparticles Prepared by Electrochemical Synthesis Method

Naked, polyvinylchloride (PVC)-coated, and polyethylene glycol (PEG)-coated Fe{sub 3}O{sub 4} nanoparticles (NPs) with an equivalent average particle size of 10 nm were prepared through an electrochemical synthesis method. The structural and magnetic properties were investigated systematically. The X-ray diffraction study coupled with the Rietveld refinement of XRD data showed that samples are crystallized in cubic spinel structure with space group referred to as Fd3m. The nature of DC magnetization versus field M (H) plot for sample resembles qualitatively with ferromagnetic (FM) systems. The AC-susceptibility data obtained at different frequencies confirmed the presence of a frequency-dependent freezing temperature. Based on the interparticle interaction strength and phenomenological models (Néel–Brown, Vogel–Fulcher, and critical slowing down), the magnetic dynamic behavior of nanoparticles was characterized. By fitting the experimental data with mentioned models, the possibility existence of superparamagnetic and a spin-glass state at low temperatures was proposed for the samples. Also, the obtained values from fitting performance showed a coating effect on interparticle interaction for PVC- and PEG-coated Fe{sub 3}O{sub 4} nanoparticles.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Separation of packaging plastics by froth flotation in a continuous pilot plant

The objective of the research was to apply froth flotation to separate post-consumer PET (Polyethylene Terephthalate) from other packaging plastics with similar density, in a continuously operated pilot plant. A representative sample composed of 85% PET, 2.5% PVC (Polyvinyl Chloride) and 11.9% PS (Polystyrene) was subjected to a combination of alkaline treatment and surfactant adsorption followed by froth flotation. A mineral processing pilot plant, owned by a Portuguese mining company, was adapted for this purpose. The experimentation showed that it is possible to produce an almost pure concentrate of PET, containing 83% of the PET in feed, in a single bank of mechanical flotation cells. The concentrate grade attained was 97.2% PET, 1.1% PVC and 1.1% PS. By simulation it was shown that the Portuguese recycling industry specifications can be attained if one cleaning and one scavenger stages are added to the circuit.

07 ISOTOPE AND RADIATION SOURCES↗

Modelling piloted ignition of wood and plastics

Highlights: Black-Right-Pointing-Pointer We model piloted ignition times of wood and plastics. Black-Right-Pointing-Pointer The model is applied on a packed bed. Black-Right-Pointing-Pointer When the air flow is above a critical level, no ignition can take place. - Abstract: To gain insight in the startup of an incinerator, this article deals with piloted ignition. A newly developed model is described to predict the piloted ignition times of wood, PMMA and PVC. The model is based on the lower flammability limit and the adiabatic flame temperature at this limit. The incoming radiative heat flux, sample thickness and moisture content are some of the used variables. Not only the ignition time can be calculated with the model, but also the mass flux and surface temperature at ignition. The ignition times for softwoods and PMMA are mainly under-predicted. For hardwoods and PVC the predicted ignition times agree well with experimental results. Due to a significant scatter in the experimental data the mass flux and surface temperature calculated with the model are hard to validate. The model is applied on the startup of a municipal waste incineration plant. For this process a maximum allowable primary air flow is derived. When the primary air flow is above this maximum air flow, no ignition can be obtained.

42 ENGINEERING↗

Thermodynamic Properties of Aggregate Coated by Different Types of Waste Plastic: Adhesion and Moisture Resistance of Asphalt-Aggregate Systems

The utilization of acidic aggregates in hot-mix asphalt (HMA) is often inevitable due to the limited supply of locally available aggregates, posing a potential threat of moisture damage to asphalt pavements. In this regard, the use of urban waste plastic to coat the low-quality aggregates is a promising way to improve the moisture resistance. This study fundamentally evaluated the compatibility between asphalt and plastic-coated aggregate by measuring surface energy, and for the first time compared the effects of different types of waste plastic including high-density polyethylene (HDPE), low-density polyethylene (LDPE), polyethylene terephthalate (PET), polyvinyl chloride (PVC), and polypropylene (PP). The plastic-coating significantly altered the chemistry of aggregate surface by increasing the nonpolar components and reducing the polar components. Such changes remarkably increased the dry adhesion energy between asphalt and aggregate and enhanced the wettability of aggregate. For the acidic aggregates, the polymeric treatment could decrease the value of wet adhesive, which indicated the debonding tendency in the presence of water was reduced. Finally, the energy ratios of the asphalt-aggregate combinations significantly increased by the surface pretreatment, which proved the effect of waste plastic coating on improving the moisture damage resistance of asphalt mixtures. By comparison, the HDPE coating was the most effective way to enhance the compatibility with asphalt, followed by PP and LDPE coatings. The PVC and PET coatings were investigated as the least effective way. In conclusion, this study cannot only contribute to the potential large-scale utilization of waste plastic but also remove the obstacles of using large quantities of acidic natural aggregate in asphalt pavements.

36 MATERIALS SCIENCE↗

Electrical and Surface Morphology of Polyvinylchloride Composites Filled with Aluminum Powder

In this work, the electrical and surface morphology of polyvinyl chloride (PVC) composites filled with different concentration of aluminum powder varying from 0 to 40 wt.% have been prepared by solution costing method. The electrical conductivity of these composites were investigated in the frequency range 100 Hz-10 MHz at room temperature. The conductivity of the composites system exhibited a strong frequency dependence particularly in the vicinity of percolation threshold (20 wt.%). It was observed that the electrical conductivity gradually increased with filler concentration and frequency and explained in terms of hopping conduction mechanism. The electrical conductivity of the composites obeys universal power law (i.e. {sigma} = Af{sup n}), where, n is power exponent. The scanning electron microscope (SEM) micrographs indicate the agglomeration of aluminum particles dispersed within the PVC at the higher aluminum concentration, yielding a conductive path through the composites. It is also corroborated with electrical conductivity result.

36 MATERIALS SCIENCE↗

Non-intrusive, high-resolution, real-time, two-dimensional imaging of multiphase materials using acoustic array sensors

Two parallel multi-element ultrasonic acoustic arrays combined with sets of focal laws for acoustic signal generation and a classical tomographic inversion algorithm are used to generate real-time two-dimensional micro seismic acoustic images of multiphase materials. Proof of concept and calibration measurements were performed for single phase and two phase liquids, uniform polyvinyl chloride (PVC) plates, and aluminum cylinders imbedded in PVC plates. Measurement artefacts, arising from the limited range of viewing angles, and the compromise between data acquisition rate and image quality are discussed. The angle range of scanning and the image resolution were varied, and the effects on the quality of the reproduction of the speed of sound profiles of model solids and liquids with known geometries and compositions were analysed in detail. The best image quality results were obtained for a scanning angle range of [−35°, 35°] at a step size of 2.5° post processed to generate images on a 40 μm square grid. The data acquisition time for high quality images with a 30 mm × 40 mm view field is 10 min. Representation of two-phase solids with large differences in speed of sound between phases and where one phase is dispersed in the form of macroscopic objects (greater than 1 mm in diameter) proved to be the most difficult to image accurately. Liquid-liquid and liquid-vapor phase boundaries, in micro porous solids by contrast, were more readily defined. Displacement of air by water and water by heptane in natural porous limestone provides illustrative kinetic examples. Measurement results with these realistic cases demonstrate the feasibility of the technique to monitor in real time and on the micrometer length scale local composition and flow of organic liquids in inorganic porous media, one of many envisioned engineering applications. Improvement of data acquisition rate is an area for future collaborative study.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

WE-EF-BRA-04: Evaluation of Dosimetric Uncertainties in Individualized Targeted Radionuclide Therapy (TRT) Treatment Planning Using Pre-Clinical Data

Purpose: Dosimetry for targeted radionuclide therapy (TRT) is moving away from conventional model-based methods towards patient-specific approaches. To address this need, a Monte Carlo (MC) dosimetry platform was developed to estimate patient-specific therapeutic 3D dose distributions based on pre-treatment imaging. However, because a standard practice for patient-specific internal dosimetry has not yet been established, there are many sources of dosimetric uncertainties. The goal of this work was to quantify the sensitivity of various parameters on MC dose estimations. Methods: The ‘diapeutic’ agent, CLR1404, was used as a proof-of-principle compound in this work. CLR1404 can be radiolabeled with either {sup 124}I for PET imaging or {sup 131}I for radiotherapy or SPECT imaging. PET/CT images of 5 mice were acquired out to 240 hrs post-injection of {sup 124}I-CLR1404. The therapeutic {sup 131}I-CLR1404 absorbed dose (AD) distribution was calculated using a Geant4-based MC dosimetry platform. A series of sensitivity studies were performed. The variables that were investigated included the PET/CT voxel resolution, partial volume corrections (PVC), material segmentation, inter-observer contouring variability, and the pre-treatment image acquisition frequency. Results: Resampling the PET/CT voxel size between 0.2–0.8 mm resulted in up to a 13% variation in the mean AD. Application of the PVC increased the mean AD by 0.5–11.2%. Less than 1% differences in ROI mean AD were observed between the tissue segmentation schemes using 4 and 27 different material compositions. Inter-observer contouring variability led to up to a 20% CoV (stdev/mean) in the mean AD between the users. Varying the number and frequency of pre-treatment images used resulted in changes in mean AD up to 176% compared to the case using all 12 images. Conclusion: Voxel resolution, contour segmentation, the image acquisition protocol most significantly impacted patient-specific TRT dosimetry. Further work is needed to develop a standard protocol that optimizes accuracy and efficiency for patient-specific internal dosimetry. BT and JG are affiliated with Cellectar Biosciences which owns the licensing rights to CLR1404 and related compounds.

60 APPLIED LIFE SCIENCES↗

Controlled combustion tests and bottom ash analysis using household waste with varying composition

The influence of the co-combustion of household waste with either sewage sludge, shredder fluff, electronic and electrical waste (WEEE) or PVC on the bottom ash quality and content was investigated under controlled laboratory conditions using a pot furnace. This laboratory approach avoids the interpretation problems related to large variations in input waste composition and combustion conditions that are observed in large scale MSW incinerators. The data for metals content, transfer coefficients and leaching values are presented relative to data for a base household waste composition that did not contain any of the added special wastes. The small WEEE invited direct measurement of precious metals content in the ashes, where measurement accuracy is facilitated by using only mobile phone scrap for small WEEE. The analyses were carried out for different particle size ranges that are of relevance to the recyclability of metals and minerals in the ashes. Positive correlations were found between elements content of the input waste and the bottom ashes, and also between increased levels of Cl, Mo and Cu in the input waste and their leaching in the bottom ashes. These correlations indicate that addition of PVC, small WEEE and shredder fluff in input waste can have a negative influence on the quality of the bottom ashes. Enrichment of Au and Ag occurred in the fractions between 0.15 and 6 mm. The precious metals content represents an economically interesting intrinsic value, even when the observed peak values are properly averaged over a larger volume of ashes. Overall, it has been shown that changes in quality and content of bottom ashes may be traced back to the varied input waste composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Temporally resolved planar measurements of transient phenomena in a partially pre-mixed swirl flame in a gas turbine model combustor

This paper presents observations and analysis of the time-dependent behavior of a 10 kW partially pre-mixed, swirl-stabilized methane-air flame exhibiting self-excited thermo-acoustic oscillations. This analysis is based on a series of measurements wherein particle image velocimetry (PIV) and planar laser-induced fluorescence (PLIF) of the OH radical were performed simultaneously at 5 kHz repetition rate over durations of 0.8 s. Chemiluminescence imaging of the OH{sup *} radical was performed separately, also at 5 kHz over 0.8 s acquisition runs. These measurements were of sufficient sampling frequency and duration to extract usable spatial and temporal frequency information on the medium to large-scale flow-field and heat-release characteristics of the flame. This analysis is used to more fully characterize the interaction between the self-excited thermo-acoustic oscillations and the dominant flow-field structure of this flame, a precessing vortex core (PVC) present in the inner recirculation zone. Interpretation of individual measurement sequences yielded insight into various physical phenomena and the underlying mechanisms driving flame dynamics. It is observed for this flame that location of the reaction zone tracks large-scale fluctuations in axial velocity and also conforms to the passage of large-scale vortical structures through the flow-field. Local extinction of the reaction zone in regions of persistently high principal compressive strain is observed. Such extinctions, however, are seen to be self healing and thus do not induce blowout. Indications of auto-ignition in regions of unburned gas near the exit are also observed. Probable auto-ignition events are frequently observed coincident with the centers of large-scale vortical structures, suggesting the phenomenon is linked to the enhanced mixing and longer residence times associated with fluid at the core of the PVC as it moves through the flame. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

5 kHz thermometry in a swirl-stabilized gas turbine model combustor using chirped probe pulse femtosecond CARS. Part 2. Analysis of swirl flame dynamics

We have performed a detailed analysis of the temperature field in a turbulent swirl flame operating with a self-excited thermo-acoustic instability. The temperature field was measured using 5 kHz chirped-probe-pulse (CPP) femtosecond (fs) coherent anti-Stokes Raman scattering (CARS). The measurements are described in detail in the part 1 companion article. In this paper, part 2, a detailed analysis of the time-resolved temperature measurements and simultaneous pressure measurements is performed to provide insight into the dynamics and structure of the swirl-stabilized flame. Here this work is the first to capture the dynamics of the flame, flow, and coupled flow-flame processes using high-fidelity, spatially- and temporally-resolved thermometry in a flame of practical relevance. The time-averaged contour plot of the temperature field indicates that the flame is very flat and stabilizes approximately 10 mm downstream of the burner face. In this region, there are very significant temperature fluctuations indicating a very high level of unsteadiness. The temperature probability distribution functions (PDFs) are clearly bimodal in this region near the injector face. A Fourier analysis of the temperature time series revealed multiple coherent oscillatory modes. The strongest oscillation was found to be coherent and in-phase with an acoustic resonance at 314 Hz, as expected from the Rayleigh criteria for the unstable flame. An analysis of the phase-conditioned average temperature fields clearly shows an axial pumping of low-temperature reactants, which are consumed after a convective delay and result in a spike in the global heat-release rate. Continued analysis also revealed a 438 Hz oscillation that was found to correspond with the dynamics of convective transport by a helical precessing vortex core (PVC). The structure of the PVC, and its interaction with the flame, were studied based on the presence of this characteristic frequency in the power spectral densities computed throughout the flow. The precision and time-resolution of the CPP fsCARS measurements was also sufficient to enable computation of the integral time-scales as well as the PDFs of the temporal temperature gradients. A sample of state space trajectories were used to provide insight into the nature of coupling between the narrowband acoustic resonance and the broadband spectrum of turbulent flame processes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Artificial intelligence-driven municipal solid waste sortation and its significance on downstream waste valorization in the United States: Techno-economic and life cycle assessment

Municipal solid waste (MSW) generation is quickly increasing due to population growth, industrialization, and urbanization. Current sorting technologies, e.g., optical sorters have low sortation efficiency and produce contaminated sorted materials unsuitable for downstream valorization. This study evaluates a novel artificial neural network (ANN)-based MSW sortation system through sorting efficiencies, economic performance, and environmental impacts. ANN system can sort up to 8 plastic types and all organic waste (i.e., food, yard, and paper waste) with 99% and 93% recovery efficiency, respectively, compared to optical sortation which could separate only polyvinyl chloride (PVC) plastic ultimately producing mixed plastics (except PVC) and organics streams as products. Nonetheless, their sortation costs are similar, $28.7 for ANN-based sortation and $28 for optical sortation per metric ton (Mt) of MSW at processing capacity of 94,860 metric tons (Mt)/yr of MSW in the United States. Additionally, ANN system produced high purity feedstocks for downstream valorization. A biochar pyrolysis plant modeled to process 3.6 and 14 Mt/h of sorted yard waste outperformed biochar production from mixed organic fraction (MOF), achieving 8% lower production cost and 34% lower global warming impact (1.37 kg CO 2 eq. per kg) compared to biochar derived from mixed organic feedstock (2.08 kg CO 2 eq.).

09 BIOMASS FUELS↗

Tribo-charging properties of waste plastic granules in process of tribo-electrostatic separation

Highlights: • The cyclone charging was more effective and stable than vibrating charging. • The small particle size was better changed than large ones and was more suitable recycled by TES. • The drying pretreatment is good for improving the short-term charging effect. - Abstract: Plastic products can be found everywhere in people’s daily life. With the consistent growth of plastic consumption, more and more plastic waste is generated. Considering the stable chemical and physics characteristics of plastic, regular waste management methods are not suitable for recycling economic strategy of each government, which has become a serious environmental problem. Recycling plastic waste is considered to be the best way to treat it, because it cannot only deduce the waste but also save the energy to produce new virgin plastic. Tribo-electrostatic separation is strongly recommended for plastic separation as it can preserve the original properties of plastic and has little additional pollution. In this study, plastic granules are generated by crushing plastic waste in waste electric and electronic equipment. The tribo-charging properties of plastic waste were studied by vibrating tribo-charging and cyclone tribo-charging. The triboelectric series obtained by vibrating was: (−)-PE–PS–PC–PVC–ABS–PP-(+), while the triboelectric series obtained by cyclone was (−)-PE–PS–PC–PVC–ABS–PP-(+). Further, the cyclone charging was more effective and stable than vibrating charging. The impact factors experiments showed that small particle size was better changed than large ones and were more suitable recycled by tribo-electrostatic separation. High relative humidity was identified as impede charging effect. The results of this study will help defining the operating parameters of subsequent separator.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Lignin-Derived Methoxyterephthalates for Performance-Advantaged Polymers and Plasticizers

Lignin-derived aromatic carboxylic acids can be produced from oxidative catalytic processes and are promising building blocks for performance-advantaged bioproducts that leverage their inherent heteroatom functionalities. Here, we synthesize 2-methoxyterephthalate and 2,6-dimethoxyterephthalate derivatives by electrochemical carboxylation of guaiacyl- and syringyl-derived lignin monomers obtained from the oxidative deconstruction of lignin. These methoxylated terephthalates are evaluated as comonomers in poly(ethylene terephthalate) (PET) and as plasticizers that could replace petrochemically-derived isophthalate and phthalate, respectively. Specifically, we copolymerize 2-methoxy- and 2,6-dimethoxyterephthalate with dimethyl terephthalate to form several PET copolymers, both of which enable the properties of PET to be tuned, with an incorporation beyond 25% producing amorphous polyesters. At 10 mol % loading in the copolymers, we demonstrate that the bioderived comonomers exhibit comparable behavior to isophthalic acid, a commonly used comonomer in PET, by lowering the crystallinity and melting temperature. Moreover, methoxyterephthalate esters (2-ethylhexyl and butyl) are compared to phthalate and terephthalate ester counterparts used as poly(vinyl chloride) (PVC) plasticizers. The bioderived plasticizers are comparable to the petroleum-derived incumbents in reducing the glass transition temperature and increasing the thermal stability of PVC. Furthermore, the dimethoxyterephthalic esters are expected to have an extended lifetime in the polymer matrix due to their lower volatility and lower diffusion coefficients calculated by molecular dynamic simulations. These results demonstrate that the isophthalate and phthalate components in polyesters and plasticizers, respectively, could be substituted with biobased methoxyterephthalate derivatives.

09 BIOMASS FUELS↗

Catalytic Borylation of Poly(vinyl chloride) Produces Adhesive Materials

Postpolymerization functionalization of polymers can create new applications for existing materials, while retaining their most favorable, intrinsic properties. Polyvinyl chloride (PVC) is a widely used, commodity polymer that is particularly challenging to modify. We report a copper-catalyzed protocol that replaces a small fraction of the C-Cl bonds in PVC with C-B bonds to boronic esters. The reaction occurs with an inexpensive catalyst comprising copper(II) chloride and an NHC ligand derived from a common ionic liquid that is distinct from the N-heterocyclic carbene (NHC) used for the borylation of small alkyl halides. The resulting materials adhere strongly to common surfaces, such as glass and metals, even more strongly than do commercial glues.

D’Angelo, Kyan A↗

A novel method for on-orbit measurement of space materials degradation

The low Earth orbit (LEO) environment is considered hazardous to spacecraft, resulting in materials degradation. Currently, in order to evaluate the degradation of materials in LEO, a retrieval of space exposed samples is required. In this study, a novel approach is proposed to evaluate degradation of materials in LEO without the need of retrieval. The method is utilizing photovoltaic cells (PVCs), an existing component onboard of any satellite. The PVCs are coated by various materials which are sensitive to different LEO constituents, such as atomic oxygen (AO) or ultra-violet (UV) radiation. The method's acronym is ORMADD (on-ORbit MAterials Degradation Detector). The ORMADD's principle of operation is based on measuring the PVC output power which depends on the cell coating material's optical transmission. Erosion of the coating by AO or coloring due to UV radiation affects its optical transmission and, accordingly, the PVC output. The ORMADD performance was tested using different coatings, such as polyimide and amorphous carbon (sensitive to AO), and siloxane based coating which is sensitive to UV radiation. The proposed ORMADD reveals sensitivity to different LEO components and can be used either as material degradation detector or as an AO monitor.

36 MATERIALS SCIENCE↗

β-decay of magic nuclei: Beyond mean-field description

Nuclear β-decay plays an important role not only in nuclear physics but also in astrophysics. The widely used self-consistent Random Phase Approximation (RPA) models tend to overestimate the half-lives of magic nuclei. To overcome this problem, we go beyond the mean-field description and include the effects of particle-vibration coupling (PVC) on top of the RPA model. The β-decay half-lives of {sup 34}Si, {sup 68}Ni, {sup 78}Ni, and {sup 132}Sn are studied within this approach in the case of the Skyrme interaction SkM*. It is found that the low-lying Gamow-Teller (GT) strength is shifted downwards with the inclusion of the PVC effect, and as a consequence, the half-lives are reduced due to the increase of the phase space available for β-decay, which leads to a good agreement between theoretical and experimental lifetimes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗